DSC iotega WS900UL, iotega WS901 Reference Manual

Page 1

iotega Wireless Security and Automation System

V1.0 Reference Manual

Models: WS900UL/WS901

WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.

Page 2

Table of Contents

Section 1: Introduction 2

1.1 About the System 2

1.2 Compatible Devices List 2

1.3 Specifications 2

Section 2: Installation 4

2.1 Alarm Controller Installation 4

2.2 Controls and Indicators 6

2.3 Enrolling Wireless PowerG Security Devices 8

Section 3: Operation 10

3.1 Using the Integrated Keypad 10

3.1.1 Key Functions 10

3.1.2 Emergency Keys 10

3.1.3 Phone Test ([*][7]) 11

3.1.4 WPS Mode ([*][8]) 11

3.1.5 Local Webpage ([*][8]) 11

3.2 Arming and Disarming Methods 11

3.2.1 Away Arming 11

3.2.2 Stay Arming 12

3.2.3 Quick Arming 12

3.2.4 Disarming 12

Section 4: Programming Options 13

4.1 Integrated Keypad Options 13

4.2 System Configuration Options 13

4.3 ADC Events to Forward 16

4.3.1 Network Configuration Options 16

4.4 Central Monitoring Station Programming Options 17

4.4.1 Other Communicator Related Options 17

4.5 Partition Configuration Options 18

4.6 Primary Temperature Zone 19

4.7 Wireless Device Configuration Options 19

4.7.1 Wirefree Keypad Configuration Options 19

4.7.2 User Configuration Options 20

4.7.3 Wireless Siren Configuration Options 20

4.7.4 Wireless Key Configuration Options 21

4.7.5 Wireless Smoke and CO Configuration Options 22

4.7.6 Wireless Glassbreak Configuration Options 22

4.7.7 Wireless Temperature Configuration Options 23

4.7.8 Wireless Flood Configurations 24

4.7.9 Wireless PIR CAM Configurations 24

4.7.10 Wireless PIR (NO CAM) Configurations 26

4.7.11 Wireless Door Window Configurations 27

4.7.12 Wireless Shock Sensor Configurations 27

4.7.13 Repeater Configuration Options 28

4.8 Available Zone Types 30

4.9 Available Zone Attributes 32

4.10 Diagnostics - Read Only 33

4.11 System Control 33

4.11.1 Network 34

Section 5: Troubleshooting 35

5.1 Testing 35

5.2 Viewing Troubles from the Integrated Keypad 35

- 2 -

Page 3

Appendix 8: Reporting Codes 37 Appendix 1: Guidelines for Locating Smoke Detectors and CO Detectors 40 Appendix 2: Regulatory Information 43 Appendix 3: EULA 48 Appendix 4: Limited Warranty 49

- 3 -

Page 4

iotega Wireless Security and Automation System

Safety Instructions for Skilled Persons

Warning: When using equipment connected t o the telephone network, always follow the basic safety instructions provided with this product. Save these instructions for future reference. Inform the end-user of the safety precautions t hat must be observed when operating t his equipment.

Before Installing The Equipment

Ensure your package includes the following items:

l Installation and User manuals, includingthe SAFETY INSTRUCTIONS.

READ and SAVE these instructions! Follow all WARNINGS AND INSTRUCTIONS specified within this document and/or on t he equipment.

l iotega alarm controller l Power Supply, direct plug-in l Ethernet cable l Mounting hardware

Selecting A Suitable Location For The Alarm Controller

Use the following list as a guide t o find a suitable location to install t his equipment:

l Locate near a power outlet. l Select a location free from vibration and shock. l Place alarm controller on aflat, stable surface and follow t he installation

instructions. Do NOT locate t his product where people may walk on the secondary circuit cable(s). Do NOT connect alarm controller t o electrical the same circuit as largeappliances. Do NOT select a location that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals or dust. Do NOT inst all t his equipment near water. (e.g., bath tub, kitchen/laundry sink, wet basement, neara swimming pool). Do NOT inst all t his equipment and accessories in areas whererisk of explosion exists. Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers. AVOID interference sources. AVOID installing equipment near heaters, air conditioners, ventilators, and refrigerators. AVOID locating equipment c lose to or on top of large metal objects (e.g., wall studs). See "Locating Detectors and Esc ape Plan" on page40for information on locating smoke and CO detectors.

SAFETY Precautions Required During Installation

l NEVER install this equipment during alightning storm. l Position c ables so that accidents can not occur. Connected cables must

NOT be subject to excessive mechanical strain.

l Use only the power supply provided with this equipment. Use of unauthorized

power supplies may cause damage. WARNING: THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BEQUICKLY DISCONNECTED. IT IS IMPERATIVE THAT ACCESSTO THE MAINS PLUGAND ASSOCIATED MAINS SOCKET/OUTLET IS NEVER OBSTRUCTED.

IMPORTANT NOTE FORNORTHAMERICA!

This alarm system must beinstalled and used within an environment that provides the pollution degree max 2 and over-voltages category II NON-HAZARDOUS LOCATIONS, indoor only. The equipment is DIRECT PLUG-IN (external transformer) and is designedto be installed, serviced and/or repaired by skilled persons only; (skilled person is defined as a person with relevant education or experience to enable him or her to identify hazards and to take appropriate actions to reduce the risks of injury to themselves and others). There are noparts replaceable by the end-user within this equipment. The wiring (cables) used for inst allation of the alarm system and acc essories, shall be insulated with PVC, TFE, PTFE, FEP, Neoprene or Polyamide. (a) Internal wiring must berouted in a manner that prevents:

- Excessive strain or loosening of wire onterminal c onnections;

- Damage of conductor insulation (b) Disposal of used batteries must be made in accordance with local waste recovery and recycling regulations. (c) Before servicing, DISCONNECT the power. (d) DO NOT route any wiring over circuit boards. (e) The installer is responsible to ensure that a readily accessible disconnect device is incorporated inthe building for permanently connected installations. The power supply must be Class II, FAIL SAFE with double or reinforced insulation between t he PRI MARY andSECONDARY CIRCUI T/ENCLOSURE and be an approvedtype acceptable to the local authorities. All national wiring rules must be observed.

- 1 -

Page 5

Section 1: Introduction

1.1 About the System

The iotega is an easy to use, wireless security and home automation panel. iotega supports a range of wireless devices via PowerG or Z-Wave. Installers set up and configure the panel through a smartphone app or cloud-based portal. End users also interact with the iotega using an intuitive smartphone app, web portal or optional wirefree and touchscreen keypads.

1.2 Compatible Devices List

The following table lists all devices compatible with the iotega.

Note: Only models withULare UL/ULC listed. For UL/ULC certified installations use only UL/ULC listed devices.

Note: 'x' refers to detector frequency: 4 = 433MHz, 9 = 868MHz, 9 = 915MHz

Product Type Model

Modules

Touchscreen Keypad* WS9TCHW

Wirefree LCD Keypad WS9LCDWF

Cellular Communicator 3G7090E-EU

PowerG

Wireless vanishing door/window contact PGx975

Wireless door/window contact w/ AUX PGx945

Wireless smoke detector PGx926

Wireless smoke and heat detector PGx916

Wireless CO detector PGx913

PIR/Pet Immune Motion Detector PGx914

Wireless PIR motion detector PGx904(P)

Wireless PIR + camera motion detector PGx934(P)

Wireless Outdoor PG PIR + camera motion

PGx944

detector

Wireless curtain motion detector PGx924

Wireless dual tech motion detector PGx984(P)

Wireless mirror motion detector PGx974(P)

Wireless outdoor motion detector PGx994

Wireless glass break detector PGx912,

PGx922

Wireless shock detector PGx935

Wireless flood detector PGx985

UL**

Product Type Model

Wireless temperature detector (indoor

PGx905

UL**

use)

Wireless 4-button key PGx939

PGx929

Wireless panic key PGx938

Wireless 2-button key PGx949

Wireless indoor siren PGx901

Wireless outdoor siren PGx911

Wireless repeater PGx920

IP Devices

Touchpad Wi-Fi Touchscreen (dedicated

WS9TCHW

as a system keypad)

Phone Cellular Phone w/Wi-Fi iOS/Android

based

Z-Wave Devices

See the portal for a complete list of supported Z-Wave devices.

Central Monitoring Station Receivers

Receiver Sur-Gard System I-IP Receiver SG-System I-

IP Receiver Sur-Gard System II Receiver SG-System II Receiver Sur-Gard System III Receiver SG-System

III Receiver Sur-Gard System IV Receiver SG-System

IV Receiver Sur-Gard System 5 Receiver SG-System 5

1.3 Specifications

Zone Configuration

l 128 wireless zones l 18 zone types and 4 programmable zone attributes l 4 touchscreen keypads supported

l 4 wirefree keypads l 16 wireless sirens l 32 wireless keys supported l 8 wireless repeaters. Note that more than one wire-

less repeater shall be installed in a given fire alarm signaling system to provide a redundant RF transmission path.

Access Codes

l Up to 99 access codes, plus one master code and

two duress codes

l Programmable user access levels and partition

assignment for each user code

Warning Device Output

l Integral sounder capable of 85 dB @ 3m l 2 remote, wireless indoor/outdoor warning devices

supported: models PGx901 (indoor), PGx911 (outdoor)

- 2 -

Page 6

Section 1: Introduction

l Programmable as steady, pulsed, temporal three (as

per ISO8201) or temporal four (CO alarm)

l Warning device sounds alarms in the following pri-

ority: Fire, CO, Burglary

Memory

l 128MB RAM l 4GB eMMC solid-state drive l 128MB embedded FLASH memory

Power Supply

Transformer: Primary: 120VAC, 0.35A, 60Hz Class II Secondary: 12VDC, 1.16A

Standard Battery

l Model: DSC model 17000178, 7.4V,1.0Ah lithium-Ion,

rechargeable

l Backup time: 4 hours l Recharging time to 85%: 24 hours

l Low battery threshold: 7.3V l Low battery restore: 7.4V l Battery Critical Shutdown: 6.5V l Battery lifespan: 3-5 years

Extended Battery

l Model: DSC model 17000179, 7.4V, 4.5Ah, lithium-

Ion, rechargeable

l Backup time: 24 hours l Recharging time to 85%: 24 hours

l Low battery threshold: 7.3V l Low battery restore: 7.4V l Battery Critical Shutdown: 6.5V l Battery lifespan: 3-5 years

Operating Environmental Conditions

l Temperature range: 0°C to +49°C (32°F-120°F) l Relative humidity: <93% non condensing

Alarm Transmitter Equipment (ATE) Specification

l Communications over cellular or Ethernet l Supports SIA and Contact ID l Complies with TS203 021-1, -2, -3 Telecom equip-

ment requirements

System Supervision Features

The iotega continuously monitors a number of possible trouble conditions and provides audible and visual indication at the keypad if a trouble is present. Trouble conditions include:

l AC power failure l Zone trouble l Fire trouble l Communicator trouble l Low battery condition l RF jam l Failure to communicate l Module fault (supervisory or tamper)

Additional Features

l 2-way audio Talk/Listen support* l Quick arming

l User, partition, module, zone and system labels l Z-WAVE-based home automation support*

* Not evaluated by UL.

- 3 -

Page 7

Section 2: Installation

2.1 Alarm Controller Installation

Installing the iotega consists of connecting and powering up the hardware, as well as configuring the device using the installer portal. A typical installation includes the following steps:

1. Create a customer account

2. Install the hardware

3. Power up the panel

4. Confirm communication

5. Enroll and install devices

6. Connect to Wifi router

7. Test the system

To install the iotega:

1. Locate the panel on a flat surface in close proximity to AC power and a wireless router.

2. Remove the plastic pull tab from the access cover on the back of the panel to activate the battery. If the battery is not installed, see Installing a new Battery.

3. Connect the Ethernet cable to the port on the back of the panel. Connect the other end of the cable to the wireless router. Installation and configuration can be done over cellular without the need for an Ethernet connection.

4. Connect the barrel jack of the plug-in adapter to the power connector on the back of the panel. Route the power cable through the strain relief channel on the bottom of the panel then plug the adapter into an AC outlet. The iotega powers up once connected to AC.

The power-up sequence is as follows:

l The integrated keypad numbers illuminate in sequence until power-up is complete. l The system powers up after approximately 2 minutes. l The Ethernet Link Speed LED illuminates steady green and the Ethernet Link Activity LED flashes rapidly to

indicate that a connection is being made to the network.

l After several minutes, depending on network speed, the Remote Connection LED illuminates steady green,

indicating that a connection has been established.

Note: If the Remote Connection Status LED flashes red, the panel may be having difficulty connecting to the remote servers. Restarting the panel may remedy the issue.

For more information on LED indicators, see "Controls and Indicators" on page 6.

5. [Optional] Connect the iotega to the customer's WiFi network. To do this, enable WPS on the router, then enable

WPS on the iotega either via the Alarm.com MobileTech app or the local keypad ([*][8][Installer Code]). If WPS is not available, connect to a valid 2.4 GHz WiFi network via the Alarm.com MobileTech app or from the panel’s local webpage. The local webpage is accessed via [*][8][Installer Code], connecting to the iotega’s access point and navigating to http://iotega. The password is the installer code twice (e.g., if Installer code is 5555, the password is 55555555).”

Figure 2-1 Panel Connections

1. Power Connector

2. Ethernet Link Speed LED

3. Ethernet Link Activity LED

4. Ethernet Port

- 4 -

Page 8

Section 2: Installation

Push tab

release

Figure 2-2 Panel Bottom Figure 2-3 Battery Compartment

1. Power cable Strain Relief

2. Access Cover for Battery, SIM Card and Reset Button

3. Speaker

4. Battery

5. Reset button

6. SIM card

7. Tamper switch

Removing the Battery

1. Remove the access cover from the back of the panel.

2. Push the battery retention tab in the direction of the arrow in Figure 2-4 .

3. Lift the battery from the front, then pull up and slide out.

Figure 2-4 Battery Removal

Installing a new battery

1. Remove the access cover from the back of the panel.

2. Insert the battery, back end first, as shown in Figure 2-4 .

3. Press the front of the battery down until the retention tab clicks into place.

4. Replace the back cover of the panel.

Note: When replacing the battery, use battery pack suitable for the application. Refer to on page2.

- 5 -

Page 9

Section 2: Installation

2.2 Controls and Indicators

The iotega provides a series of LED indicators to notify users of system status.

Figure 2-5 LED Indicators

1. Power LED

2. Ready to Arm LED

3. Armed LED

4. Trouble LED

5. WiFi Signal Strength LED

6. Cellular Signal Strength LED

7. Remote Connection LED

8. Siren

9. Microphone

Table 2-1 LED Indicator Operation

LED Indicator Description

Power ON Steady

[Green]

OFF · System is not powered On

Flashing System test in progress (Ready, Trouble and Arm LED’s flashing at same time)

Ready ON Steady

[Green]

OFF Partition is not ready to arm. Not all zones are secure or an alarm is present.

Flashing [Green] Installer Walk Test (Ready, Trouble and Arm LED’s flashing at same time) or sys-

AC power is connected to the system

· NO AC connected, and system is operating on backup battery

· NO AC connected and backup battery is discharged

Partition is ready to arm

tem test in progress (Ready, Trouble and Arm LED’s flashing at same time)

- 6 -

Page 10

Section 2: Installation

LED Indicator Description

Armed ON Steady

[Red]

Flashing [Red]

OFF Partition is disarmed or audible alarm annunciation is deactivated

Trouble ON Steady

[Amber]

Single flash [Amber]

Two flashes [Amber]

Three Flashes [Amber]

Flashing [Amber]

OFF No system troubles

Wi-Fi Signal

Strength

Cellular Sig-

ON Steady [Green] Strong Signal Connection

ON Flashing [Green]

ON Steady [Amber]

ON Flashing [Amber]

On Steady [Red] No Signal

Flashing [Amber]

OFF WiFi disabled

ON Steady [Green] Strong signal connection

Partition is armed

System in Alarm. [Note: this LED does not flash for silent alarms or panic alarms]

Installer Walk Test (Ready, Trouble and Arm LED’s flashing at same time) or system test in progress (Ready, Trouble and Arm LED’s flashing at same time)

System trouble is present

[*][2] System Trouble menu level 1

[*][2] System Trouble menu 2

[*][2] System Trouble menu 3

Access code is required to view Trouble menu, Installer Walk Test (Ready, Trouble and Arm LED’s flashing at same time) or a system test is in progress ( Ready, Trouble and Arm LED’s flashing at same time)

Wi-Fi active in WSA mode (for AP mode)

Radio active with weak signal connection

Z-Wave is active in learn pair mode

System Test (AC, Ready, Trouble, Arm LED’s, WiFi Trouble, Cellular Trouble & System Remote Status flashing at same time)

nal Strength

ON Steady [Amber]

ON Steady [Red]

Flashing [Amber]

OFF Cellular is disabled

Weak signal connection

No Signal or no connection

System Test (AC, Ready, Trouble, Arm LED’s, WiFi Trouble, Cellular Trouble & System remote status flashing at same time)

- 7 -

Page 11

Section 2: Installation

LED Indicator Description

Remote Con-

nection Status

Note: During a system test, All LEDs flash.

ON Steady [Green] Link to remote server is active

ON Flash [Red]

OFF Link to remote server is not active or

Flashing [Amber]

Link to remote server is active but has failed to communicate

the panel has not been activated with Alarm.com

System Test (AC, Ready, Trouble, Arm LED’s, WiFi Trouble, Cellular Trouble & System Remote Status flashing at same time)

Note: If the Remote Connection status LED flashes red, the panel may be having difficulty connecting to the remote server. Restarting the panel may remedy the issue. If the problem persists, contact technical support

Reset Button

Pressing and holding the Reset button, located under the battery cover (see figure 3-3), for a minimum of 10 seconds defaults the interactive app to factory settings. The iotega beeps once to confirm successful reset. Pressing and holding the Reset button for a minimum of 20 seconds resets the panels network configuration to factory defaults. The iotega beeps twice to confirm successful reset.

Note: The system must be disarmed with no alarms in memory in order for the Reset button to function as described above.

Tamper Switch

The panel includes a tamper switch under the back battery cover. If the battery cover is removed while the system is disarmed, the tamper condition must be cleared before arming is permitted. If the battery cover is removed while the system is armed, the bell sounds, a system tamper is logged and communicated to the central monitoring station, and a system temper trouble is displayed in the Trouble menu.

Low Power Operation

In the event of an AC power outage, all Wi-Fi and home automation functions are discontinued. The panel uses battery power to communicate alarms or critical conditions.

2.3 Enrolling Wireless PowerG Security Devices

Device enrollment and configuration is done using the installer portal. To enroll wireless devices, navigate to Equipment > Sensors > Add a Sensor to put the panel into Add mode. Select AutoLearn or Remote Add.

Auto-Learn mode

1. Power up the sensor or device and trigger it according to the instructions in the device manual. Enrolled devices are displayed on the Mobile Tech page in the Added Devices section.

2. Once all devices are added, choose Exit.

3. Edit the device name, group, and partition as needed.

4. Click Save to finish.

Add Sensor and Peripheral Devices (Remote Add)

1. Enter the device ID, zone definition, partition, name, and ESN into the appropriate fields.

2. Click Add Sensor to finish.

The device may need to be tampered when in range of the panel in order to start functioning. The wireless devices in the table below each have a dedicated Enroll button, located on the circuit board inside the plastic casing. A Phillips screw must be removed on most devices to gain access. Refer to the installation instructions provided with the device for more information.

- 8 -

Page 12

Section 2: Installation

PGx901 I ndoor siren PGx924 Curtain motion detector

PGx904 PIR/Pet Immune motion detector PGx926 Smoke detector

PGx914 PIR/Pet Immune motion detector PGx935 Shock detector and magnetic contact

PGx905 T emperature detector PGx944 T ower Cam motion detect or

PGx911 Outdoor siren PGx945 Magnetic contact with Aux.

PGx913 Carbon Monoxide detector

Note: enrolls automatically onpower-up

PGx912 Glassbreak detector PGx975 Magnetic contact (vanishing)

PGx916 Smoke and heat detector PGx984 Mirror PIR motion detector

PGx920 Wireless repeater

Note: hold Enroll button until red and green LEDs light steady

PGx922 Glassbreak detector PGx994 Outdoor PIR motion detector

PGx974 Mirror PIR with anti-masking

PGx985 F lood detector

To enroll wireless keys:

PGx929/PGx9394-button wireless key Press and hold [*] button until LED lights steady then release.

PGx949 2-button wireless key Press and hold unlock button until LED lights steady then release.

PGx938 Panic key Press and hold button until LED lights steady then release.

- 9 -

Page 13

Section 3: Operation

This section describes how to use the iotega‘s integrated keypad.

3.1 Using the Integrated Keypad

The iotega includes a built-in, touch sensitive keypad that activates by proximity. From the keypad, users can arm and disarm the system, view system troubles, and activate the Fire (F), Auxiliary (A) and Panic (P) keys. The integrated keypad can be configured to work on any partition.

Figure 3-1 Keypad - Normal Operating Mode Figure 3-2 Keypad - Shift Mode

3.1.1 Key Functions

The following keys are enabled during normal operating mode:

Key Description

(0-9)numeric entry (access code)

# clear entries, return to previous screen

* [*] 2 for Troubles, see "Viewing Troubles from the Integrated Keypad" on page 35.

[*] 8 to enable WiFi access point (to add IP devices, i.e.,touchscreen keypad). See "WPS Mode ([*]8)" for more information. [*] 7 to initiate a phone test with ADC.

↑ Shift mode switches between numeric and Emergency keys

3.1.2 Emergency Keys

The Fire, Auxiliary and Panic keys can be enabled independently by the installer. All three are enabled by default. The Emergency keys behave as follows:

Key Alarm Type Indication Reporting Code

Fire Keypad beeps 3 times. Siren sounds. Signal sent to monitoring station Fire Alarm (if pro-

grammed)

Auxiliary Keypad beeps 3 times when activated and 10 times when the event is suc-

cessfully received by the central monitoring station.

Auxiliary alarm

- 10 -

Page 14

Section 3: Operation

Panic Keypad beeps three times and a signal is sent to the monitoring station.

Can be configured as audible or silent

To use the Emergency keys:

1. Press the Shift key (↑). The Emergencykeys are illuminated (if enabled ). If an Emergency key is not pressed within 10 seconds, the keypad returns to normal operating mode.

2. Press and hold an Emergency key for 2 seconds to activate the alarm.

Panic alarm

3.1.3 Phone Test ([*][7])

The Phone test sends a test transmission from the iotega to the monitoring station. This test helps installers determine if the panel is communicating properly. Successful completion of the test is indicated on the installer portal. If the test fails, an FTC error is logged. The Phone test can be initiated by installers and the system master user, and may take several minutes to complete. To perform a Phone test:

l Press [*][7][01][installer code], or [*][7][02][master code]

3.1.4 WPS Mode ([*][8])

WPS (WiFi Protected Setup) mode activates iotega's WiFi access point to facilitate connection with IP devices, such as the touchscreen keypad and IP cameras. To enable WPS mode:

1. At the installation site, tap [*] 8 on the integrated kaypad.

2. Enter a valid installer code. The WiFi signal strength LED flashes for two minutes to indicate the system is in WPS mode.

The WPS window expires after 2 minutes.

3.1.5 Local Webpage ([*][8])

This mode is used to connect the iotega to the local WiFi router, configure static/dynamic ip address, configure WiFi settings and to view panel, cellular status/information and firmware versions.

Note: WLAN Client Mode and Access Point must be enabled to use this feature. The access window expires after 10 minutes.

To enable Local Webpage mode:

1. At the installation site, tap [*] 8 on the integrated kaypad.

2. Enter a valid installer code. The WiFi signal strength LED flashes for two minutes to indicate the system is in local webpage mode.

To access the local webpage:

1. On your local device (mobile/laptop), locate the Guest AP network and join.

2. Enter your password (installer code twice. e.g., 55555555).

3. Use a web browser to access http://iotega.

Note: The access window timer can be restarted by pressing [*][8][installer code] again.

3.2 Arming and Disarming Methods

This section describes the arming methods available on the iotega.

3.2.1 Away Arming

Away Arming arms the entire system, including the perimeter and interior devices. The Ready light must be on to arm the system. If the Ready light is off, ensure all protected doors and windows are secure or bypassed. To arm the system, enter a valid access code. To disarm, enter a valid access code. During exit delay, the Armed and Ready indicators turn on and the keypad beeps once every second during the exit delay (and three times a second during the last 10 seconds) to alert the user to leave via a delay zone. The Ready light turns off when the Exit Delay ends. When the exit delay has expired, the system is armed as indicated by the following conditions:

- 11 -

Page 15

Section 3: Operation

l the Ready indicator turns off. l the Armed indicator stays on. l the panel is silent.

Note: In Away Arming mode, bypassed zones are logged and communicated to the central monitoring station.

3.2.2 Stay Arming

Note: Requires at least one zone defined as Interior Stay/Away or Delay Stay/Away for this function to work.

Stay Arming is intended to arm the perimeter of the premises while permitting movement within. The Ready light must be on to arm the system. If the Ready light is off, ensure all protected doors and windows are secure or bypassed. To Stay arm the system, enter a valid user code and stay within the premises (do NOT violate a zone programmed as Delay). The Armed light turns on once a function key is pressed or an access code is entered. The Ready indicator turns off and the Armed indicator turns on when the exit delay ends.

Note: In Stay Arming mode, all bypassed stay/away zones are logged and communicated to the central monitoring station.

3.2.3 Quick Arming

Quick arming enables users to arm the system via touchscreen or wirefree keypad without entering an access code. This provides a fast method of arming for regular users and allows users without an access code to arm the system. The Quick Arming feature must be enabled in order for this function to operate. See "Quick Arm" on page 18.

3.2.4 Disarming

The user must enter through a door programmed as Delay. Upon entering, the panel emits a steady entry delay tone (and a pulsing tone during the last 10 seconds of entry delay) to alert the user to disarm the system. To disarm the system, enter a valid user code or use a wireless key. If an alarm occurred while the panel was armed, the keypad numbers corresponding to the violated zones are illuminated. If the system is disarmed using a method other than the keypad (e.g., wireless key), the panel emits three squawks to indicate alarm in memory.

- 12 -

Page 16

Section 4: Programming Options

Section 4: Programming

Options

This section provides descriptions of all alarm controller options, both programmable and read-only. Programming options are accessed through the Installer portal.

4.1 Integrated Keypad Options

This section describes programmable options for the iotega’s integrated keypad.

Keypad Partition Assignment

This section is used to select the partition that the built-in keypad will operate on.

Default: 1

Valid range: 1-2

Fire Button Options

This function is used to enable or disable the Fire [F] button on the integrated keypad. When enabled, pressing and holding the [F] button for 2 seconds triggers a Fire alarm. The system sounds 3 beeps to acknowledge the valid alarm and the siren sounds with a pulsing tone. An alarm reporting code is transmitted to the central monitoring station.

Default: Enabled

Valid range: Enabled, Disabled

Auxiliary Button Options

This function is used to enable or disable the Auxiliary [A] button on the integrated keypad. When enabled, pressing and holding the [A] button for 2 seconds sends an emergency alarm reporting code to the central monitoring station. When the emergency reporting code is received, the keypad beeps 10 times.

Default: Enabled

Valid range: Enabled, Disabled

Panic Button

This function is used to enable or disable the Panic [P] button on the integrated keypad. When enabled, pressing and holding the [P] button for 2 seconds sends an emergency alarm reporting code to the central monitoring station.

Default: Enabled

Valid range: Enabled, Disabled

Internal Buzzer Control

This option is used to set the tone of the internal buzzer. The tnoe ranges from lowest (1) to highest (15). Programming (0) turns off the buzzer.

Default: 7

Valid range: 0-15

4.2 System Configuration Options

This section describes programmable options for the alarm controller.

System Area Label

Use this option to program a custom label for the security system. This label is used in the event buffer when system events occur.

Default: System Area

Valid range: 32 Characters

System Account Number

The system account number is used to identify the alarm system when communicating system events to the central monitoring station. The system account number can be either 4 or 6 digits long. Program a 6-digit code only when using the SIA reporting format. SIA uses this account number for all partitions and system events. All other reporting formats use a 4-digit system account number to report system maintenance (e.g., low battery, zone fault) and test transmission events. To program a 4-digit system account number, enter 4 digits followed by FF.

Note: This field is mandatory for communication with the central monitoring station.

Default: F FFFFF (disabled)

Valid range: 000001 t o FFFFFF (Hexadecimal)

Event Reporting Format

The panel has an assigned communicator protocol for transmitting zone alarms, tampers, faults and other signals to the central monitoring station. View the assigned protocol on the portal by navigating to Monitoring Settings and clicking View Additional Receiver Information.

SIA Format - Level 2 ( Hard Coded )

The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October 1997. This format sends the account code along with its data transmission. The transmission appears similar to the following at the receiver: N ri1 BA 01 N = New Event ri1 = Partition /Area Identifier BA = Burglary Alarm 01 = Zone 1 A system event uses the Area Identifier ri00.

- 13 -

Page 17

Section 4: Programming Options

Bell Squawk on Arming

With this option enabled, the iotega chirps the sirens briefly at full volume when the system is successfully armed. The following options are provided to customize this option: None: Sirens do not chirp when the system is armed. All RF: Sirens chirp when armed by any wireless device. RF Wireless Key: Sirens chirp only when armed by a wireless key. RF Keypad: Sirens chirp only when armed by a wirefree keypad.

Default: RF Wireless Key

Valid range: None, All RF, RF Wireless Key, RF Keypad

Chime on Zone Opening

When this option is enabled, the door chime sounds each time an appropriately configured zone is opened. The Door Chime attribute must be set to ON for every zone that requires a chime on opening.

Default: Enabled

Valid range: Enabled, Disabled

Chime on Zone Closing

When this option is enabled, the door chime sounds each time an appropriately configured zone is closed. The Door Chime attribute must be set to ON for every zone that requires a chime on opening.

Default: Disabled

Valid range: Enabled, Disabled

Trouble Beeps (Audible/ Auto-silent)

When this option is enabled, trouble beeps are not sounded for any trouble condition except Fire/CO. For these, trouble beeps sound every 10 seconds for the duration of the trouble. When this option is disabled, the system announces troubles through the keypad buzzer every 10 seconds. Pressing any key on the keypad silences the trouble beeps; however, new troubles will restart trouble beeps. For troubles that have been silenced but are still present, trouble beeps restart daily at 7AM.

Default: Enabled

Valid range: Enabled, Disabled

Fire Bell Time-out takes priority over Burglary Bell Time-out.

Default: 5 Minutes

Valid range: 0 t o 255 Minutes

Audible Panic

This option is used to set internal buzzer behavior when the Panic key is pressed. When set to Audible, pressing the Panic key causes the buzzer to sound a series of 3 beeps to acknowledge the alarm. The buzzer then sounds a steady tone for the length of the bell time-out or until an access code is entered. When set to Silent, pressing the Panic key causes the buzzer and the bell output to remain silent, but the alarm is still transmitted (if programmed).

Default: Silent

Valid range: Audible, Silent

Access Code Required For Bypassing

When this option is enabled, an access code is required to view the zone bypass menu. When this option is disabled, the zone bypass menu is accessible to anyone.

Default: Disabled

Valid range: Enabled/Disabled

RF Jam

When this option is enabled, the alarm panel detects and reports continuous wireless signals that could interfere with the operation of the alarm system. UL: The iotega detects and reports continuous RF interference using UL 20/20 requirements for wireless jam detection (20 seconds of continuous jam detection is required).

Default: Disabled (Note: RF Jam shall be enabled for UL/ULC applications)

Valid range: 00: Disabled, 01: UL 20/20, 02: EN 30/60, 03: Class 6 30/60

Access Code Required to View/Silence Troubles

This option is used to enable and disable the need to enter an access code before viewing and silencing system troubles.

Default: Disabled

Valid range: Enabled, Disabled

Burglary Bell Time-out

This option determines the length of time the system siren sounds for. System tampers follow this timer, but Fire alarms and keypad buzzers do not.

Default: 4 Minutes

Valid range: 0 t o 255 Minutes

Fire Bell Time-Out

This option determines the maximum activation time for fire alarm sirens. Each partition has a dedicated Fire Bell Timeout timer.

Cellular Low Signal Trouble

This option is used to determine if the system will generate a trouble event when a weak cellular signal is detected. When enabled, a trouble event is generated if the radio signal level falls below threshold level (average CSQ level 4 or less).

Default: Enabled

Valid range: Enabled, Disabled

- 14 -

Page 18

Section 4: Programming Options

Lockout Attempts

This option is used to program the number of invalid access code entries allowed before the keypad is locked. When keypad lockout occurs, the system is inaccessible by keypad for the programmed duration. If the number of invalid attempts is not reached within one hour, or if a valid access code is entered, the counter is reset to 0 after 5 minutes. Each keypad keeps track of its own lockout count and time.

Note: The FAP keys are not locked.

Default: 0

Valid range: 0 t o 255

Keypad Lockout Duration

This section displays the length of time that the integrated keypad remains locked after the programmed number of access code attempts has been exceeded.

Default: 5 minutes

Valid range: Read-only

Fire Supervision

This option is used to control system supervision of smoke, CO and heat detectors. When this option is enabled, fire detection devices are monitored over a four-hour period. If a device fails to report within the four-hour window, a hardware fault trouble is logged for the zone. With this option disabled, fire detection devices follow the programmed supervisory window up to a maximum time of 18 hours. After 18 hours, fire detection devices go into fault, regardless of the programmed supervisory window.

Default: Disabled

Valid range: Enabled/Disabled

Wireless Supervisory Window

Use this option to program the time window for reception of supervision (keep alive) signals from wireless devices enrolled on the system. If a device does not report at least once within the programmed time window, a hardware fault trouble is generated.

Default: 24 Hours

Valid range: 1 Hour, 2 Hours, 4 Hours, 8 Hours, 12 Hours, 24 Hours, Disabled

Wi-Fi Low Signal Trouble

This option is used to determine if the system will log and report low Wi-Fi signals.

Default: Enabled

Valid range: Enabled, Disabled

informing them that the previous event should be disregarded. The communications cancel window begins after the transmission delay expires and a zone alarm is transmitted. If an access code is entered during this window, a reporting code is communicated and logged. If the window expires without an access code entry or a code is entered after the window, the communications canceled event is not logged or communicated.

Note: The cancel window does not start after an Emergency key alarm.

Default: 0 Minutes (Standard)

Valid range: 0 to 255 Minutes (Standard)

Swinger Shutdown

This value defines the number of communication attempts made before the event goes into swinger shutdown. Once the programmed number of alarm/restore events have been communicated for an event, no further alarm/restore events are sent until swinger shutdown is reset. The last restore event is not communicated until swinger shutdown is cleared.

Default: 003 (Standard)

Valid range: 000-014 (Standard)

Communication Delay

This value defines the delay before an alarm is transmitted. The delay is for zones which have the Transmission Delay attribute enabled. Each partition shares the same active timer. If the delay is already active due to an alarm on a different partition, any new activity on another partition does not restart the communications delay timer. Burglary Verified events are postponed until after the transmission delay expires. When a valid disarming procedure is used while the transmission delay is active, a communications canceled message is briefly displayed on the keypad when the delay is canceled.

Default: 000 (Standard)

Valid range: 000-255 Seconds (Standard)

AC Failure Communication Delay

This value determines the delay before an AC failure or restore is logged and reported. The AC failure or restore is still displayed immediately in the Trouble menu.

Default: 030Minutes

Valid range: 000 to 255 Minutes

Communication Cancel Window

This option is used to program the length of the Communication Cancel window. Entering an access code during the communicaiton cancel window sends a code to the central monitoring station,

Wireless LowBattery Communication Delay

When a zone reports a low battery condition, the trouble is indicated immediately in the Trouble menu, but transmission to the monitoring station and logging to the event buffer is delayed by the number of days programmed in this section. If the low battery condition is not corrected before the delay

- 15 -

Page 19

Section 4: Programming Options

expires, the condition is transmitted and logged to the event buffer. The Low Battery Restore transmission is not delayed.

Default: 007days

Valid range: 000 to 255 days

[A] Key Alarm control (for 2-way Voice) - Read Only

When this option is enabled, a 2-way talk/listen-in session is initiated when the Auxiliary [A] key is tapped.

Default: Enabled

Valid range: Enabled

[P] Key Alarm Control (for 2-way Voice) - Read Only

When this option is enabled, a 2-way talk/listen-in session is initiated when the Panic [P] key is tapped. Note that the [P] key must be programmed as audible in order to initiate 2way audio. If the [P] key is programmed as silent, a listen-in only session is initiated when the Panic [P] key is tapped.

Default: Enabled

Valid range: Enable

Duress Alarm Control (for 2-way Voice) - Read Only

When this option is enabled, a Listen-in session is initiated when a Duress alarm occurs.

Default: Enabled

Valid range: Enabled

Wireless Siren Control During 2-way Voice

When this option is enabled and an audible alarm is present, the wireless siren activates during a 2-way audio session. When disabled, the wireless siren is silent when a 2-way audio session begins. This allows the user to better hear the operator. The sounder resumes operation for the timeout duration if the panel has not been disarmed at the end of the 2way session.

Default: Enabled

Valid range: Enabled, Disabled

Onboard Siren Control During 2-way Voice

When this option is enabled and an audible alarm is present, the panel's onboard siren activates during a 2-way audio session. When disabled, the onboard siren is silent when a 2-way audio session begins. This allows the user to better hear the operator. The sounder resumes operation for the timeout duration if the panel has not been disarmed at the end of the 2way session.

Note: This option shall be enabled for UL/ULC.

Default: Disabled

Valid range: Enabled, Disabled

4.3 ADC Events to Forward

This section is used to configure monitoring station and receiver settings for the panel. ADC Events to Forward is accessed via the Alarm.com Partner Portal or Mobile Tech app under Monitoring Settings. The following events are selectable:

l Alarms l Bypass l Crash & Smash l Panics l Phone Tests l All Events l Sensor Tampers l Trouble Restorals l Armings (Openings/Closings) l Cancels l Panel Not Responding l Phone Communication Failures l Troubles l RF Receiver Jamming l Sensor Tests

4.3.1 Network Configuration Options

LAN/WAN Obtain IP Address

This option is used to determine how an IP address for LAN/WAN communication is obtained. When DHCP is selected, the iotega is automatically assigned an IP address by the network. When Static IP is selected, a consistent IP address is used.

Default: DHCP (Automatic)

Valid range: DHCP, Static IP

LAN/WAN IP Address

This section is used to program a static IP address. To use a static IP address, the option LAN/WLAN Obtain IP Address must be set to Static IP address.

Default: 000.000.000.000

Valid range: 000.000.000.000to 255.255.255.255

LAN/WLAN IP Subnet Mask

This section is used to program a LAN/WLAN subnet mask. To use the subnet mask, the option LAN/WLAN Obtain IP Address must be set to Static IP address.

Default: 255.255.255.255

Valid range: 000.000.000.000to 255.255.255.255

LAN/WLAN Gateway IP Address

This section is used to program the IP address for the network’s default gateway. To use this gateway, the option LAN/WLAN Obtain IP Address must be set to Static IP address.

- 16 -

Page 20

Section 4: Programming Options

Default: 000.000.000.000

Valid range: 000.000.000.000to 255.255.255.255

Panel's Preferred DNS Server

This section is used to program the name of the preferred Domain Name System server.

Note: To use the panel’s preferred DNS server, the option LAN/WLAN Obtain IP Address must be set to Static IP address.

Default: 000.000.000.000

Valid range: 000.000.000.000to 255.255.255.255

Panel's Alternate DNS Server

This section is used to program the name of an alternate Domain Name System server to be used if the preferred DNS server is unavailable.

Note: To use the panel’s alternate DNS server, the option LAN/WLAN Obtain IP Address must be set to Static IP address.

Default: 000.000.000.000

Valid range: 000.000.000.000to 255.255.255.255

WLAN SSID

This section is used to program a network name (unique identifier) for the panel.

Default: None

Valid range: Alphanumeric

WLAN Client Control

This option is used to control WiFi client mode.

Default: Enabled

Valid range: Enabled/Disabled

Time Zone

This option defines the time zone that the alarm system will operate in.

Default: US Eastern

Valid

US-Alaska, US-Aleutian, US-Arizona, US-Central, US-Eastern, US-

range:

Hawaii, US-Indiana-East, US-Indiana-Starke, US-Michigan, US-Mountain, US-Pacific, US-Samoa, CA-Atlantic, CA-Central, CA-Eastern, CA-Mountain, CA-Newfoundland, CA-Pacific, CA-Saskatc hewan, CASaskatchewan-East, CA-Yukon

Time zone is set automatically by ADC based on the installation address provided in the customer setup.

4.4 Central Monitoring Station Programming Options

The following section provides descriptions of all programming options for communications between the iotega and the central monitoring station.

Communication Path

Use this option to select the method by which the panel communicates to the central monitoring station. Choose one of the following: Cellular: The system communicates to the central monitoring station via cellular connection only. Ethernet and Cellular: The system communicates to the central monitoring station via Ethernet as the primary path and cellular as the secondary path.

Default: None

Valid range: Cellular, Ethernet andCellular

4.4.1 Other Communicator Related Options

WLAN Security Type

This option is used to select which encryption protocol the system uses to secure the wireless network.

Default: WPA2 PSK AES

Valid range: WPA PSK TKIP

WPA PSK AES WPA PSK TKIP AES WPA2 PSK TKIP WPA2 PSK AES WPA2 PSK TKIP AES

WLAN Security Key

This section is used to program a password for the Wi-Fi network.

Default: None

Valid range: 32 character ACCII

Cellular Test Transmission Time

Enter a 4-digit number (0000-2359) using the 24-hour clock format (HHMM) to set the time of day a cellular test transmission is sent. Programming a value of 9999 disables the test transmission time.

Note: The internal date and time will automatically be programmed when the unit communicates with the primary receiver.

Default: 9999

Valid range: 0000 t o 2359, 9999 to disable

Cellular Test Transmission Cycle

This option is used to program how often, in minutes, cellular test transmissions are sent. Once the initial test transmission is sent, all future test transmissions are offset by the programmed number of minutes.

Default: 0 minutes.

Valid range: 000000 to 999999minutes

- 17 -

Page 21

Section 4: Programming Options

Note: Programming an interval of less than 5 minutes or a value greater than 999999 disables the test transmission.

4.5 Partition Configuration Options

This section describes programming options used to configure individual partitions.

Partition Label

This option is used to add a unique label to each partition on the system. This label is displayed on partition keypads and event messages.

Default: Blank

Valid range: 32 character ASCII

Partition Account Number

This option is used to add a unique account number to a partition. When using formats other than SIA, the account number identifies the alarm system to the central monitoring station when communicating partition-specific events.

Note: The iotega will not communicate if the account number is not programmed.

Default: FFFF

Valid range: 0001 t o FFFF (FFFF to disable communication)

Entry Delay 1

This value determines the entry delay time for Delay 1 type zones.

Default: 30 seconds.

Max. 45 seconds requiredfor UL/ULC

Valid range: 0 t o 255 (standard)

30 to 255 Seconds (UL/ULC)

Closing Delinquency Delay

This value determines the time the alarm system delays before transmitting a close delinquency event to the central monitoring station.

Default: 30 Days

Valid range: 0 t o 255 Days

Cross Zone Delay

If another zone with the Burglary Verification attribute enabled is violated within the duration of this timer, a Burglary Verified event is communicated and logged.

Default: 0 Seconds

Valid range: 0 to 255 Seconds

Quick Arm

When this option is enabled, the iotega can be armed without entering an access code.

Note: Quick arming cannot be initiated from the integrated keypad.

Default: Enabled

Valid range: Enabled/Disabled

Quick Exit

When this option is enabled, users can temporarily bypass a Delay 1 or Delay 2 zone to exit the premises when the system is armed. Only one delay zone may be activated. Activity on another delay zone initiates the appropriate alarm sequence. If the delay zone is still open two minutes after being bypassed, entry delay is initiated. If armed in Stay mode, the automatic bypass on Stay/Away zones remains.

Note: Quick Exit cannot be initiated from the integrated keypad.

Default: Disabled

Valid range: Enabled/Disabled

Entry Delay 2

This value determines the entry delay time for Delay 2 type zones.

Default: 45 seconds (standard)

Valid range: 0 t o 255 (standard)

Max. 45 seconds requiredfor UL/ULC

30 to 255 Seconds (UL/ULC)

Exit Delay

This value determines the length of time given to exit the premises before the system becomes fully armed.

Default: 120 seconds (standard). Note: Minimum 45 seconds requiredfor

Valid range:

UL/ULC

0 t o 255 (standard) 45 to 255 seconds (UL/ULC)

Internal Siren

When this option is enabled, The iotega’s built-in siren activates during an alarm.

Default: Enabled

Valid range: Enabled/Disabled

Internal Buzzer

When this option is enabled, the iotega’s built-in buzzer provides auditory feedback (e.g., key presses, door chime).

Default: Enabled

Valid range: Enabled/Disabled

Chime Control

When this option is enabled, the iotega sounds door chime beeps whenever a zone with the Door Chime attribute ON is opened.

- 18 -

Page 22

Section 4: Programming Options

Default: Disabled

Valid range: Enabled/Disabled

Duress Access Code (Pin)

This section is used to program an access code designated as Duress. When this code is used to perform any function on the partition, a Duress reporting code is sent to the central monitoring station.

Default: Blank

Valid range: 4-digit, 0-9

4.6 Primary Temperature Zone

Primary Temperature Zone

Use this option to select the primary temperature zone to display on partition tablets and keypads. This option can be programmed by level 1 users via remote app or local tablet.

Default: 000 (no temperature zoneselected)

Valid range: 000-128

Secondary Temperature Zone

Use this option to select the secondary temperature zone to display on partition tablets and keypads. This option can be programmed by level 1 users via remote app or local tablet.

Default: 000 (no temperature zoneselected)

Valid range: 000-128

Panic ButtonOptions

This feature is used to enable and disable the Fire, Medical, and Panic keys on the wirefree keypad. Programming is done through the installer portal under Command Cata- log>Keypad/Screen Settings>Panic Button Options.

Default: Fire, Medical and Police panic

Valid

Fire panic only, Medical panic only, Police panic only, Fire and Med-

range:

ical panic, Fire and Police panic, Fire, Medical and Police panic, None

Internal Buzzer Control

This option is used to set the volume level of the keypad’s internal buzzer. The volume ranges from lowest (1) to highest (15). Programming (0) turns off the buzzer.

Default: 7

Valid range: 0-15

Keypad Tamper

When this option is enabled, the wirefree keypad tamper switch generates tamper alarms and restores when activated.

Default: Disabled

Valid range: Enabled/Disabled

Armed LED Power Save Option

This option is used to control the Armed LED on/off state. If enabled, the Armed LED does not illuminate when the system is armed to conserve battery life.

Default: Disabled

Valid range: Read-only

4.7 Wireless Device Configuration Options

This section describes programming options used to configure supported wireless PowerG devices.

4.7.1 Wirefree Keypad Configuration Options

The following sections describe programming options used to configure the available wirefree keypad.

Keypad Label

This section is used to program a user-friendly name for the keypad.

Default: Blank

Valid range: 32 character ASCII

Keypad Partition Assignment

This section is used to program the partition that the wirefree keypad is assigned to.

Default: 1

0 t o 255 1-4, ALL

Auto Scroll Open Zones Option

When this option is enabled, the keypad automatically scrolls through and displays all open zones.

Default: Enabled

Valid range: Read-only

Alarms Displayed While Armed Option

When this option is enabled, the keypad displays alarms on affected zones while the system is armed. If disabled, zones in alarm are not displayed while the system is armed.

Default: Enabled

Valid range: Read-only

Power LED AC Present Option

When this option is enabled, the Power LED illuminates when the iotega has electrical power. When disabled, The Power LED illuminates when the iotega does not have electrical power.

Default: Enabled

Valid range: Read-only

- 19 -

Page 23

Section 4: Programming Options

Auto Alarm Scroll Option

When this option is enabled, the keypad scrolls automatically and displays all alarms when the bell is active or when an alarm is in memory while armed.

Default: Enabled

Valid range: Read-only

Local Clock Display Option

When this option is enabled, the keypad displays the time and date when not in use.

Default: Enabled

Valid range: Read-only

4.7.2 User Configuration Options

This section describes programming options for configuring system users.

User Partition Assignment

This section is used to assign system user 2-100 to an available partition. Users may be assigned to multiple partitions. Basic/Standard users may only assign new users to partitions they themselves have permission to access.

Default: 1

Valid range: 1, 2, 3, 4, All

User Access Code (Pin)

This section is used to program a 4-digit code used to access the panel. Each user requires a code. Duplicate codes are not permitted.

Default: Blank

Valid range: 0000 t o 9999

User Access Level

Each system user is assigned an access level that determines the features they can use. All codes are 4-digit decimal entries. Duplicate codes are not permitted. The following access levels may be available on your panel:

Master User

Has access to all system functionality. These functions include:

l Bypass/unbypass zones l Chime enable/disable l View troubles l View alarms in memory l Create new users (via user app) l Initiate a system test l Update Panel WiFi (client mode) SSID & password l Adjust keypad settings sucha as buzzer tone and

volume, display contrast and brightness

l Assign wireless keys to users

Level 0: Professional Installer

Has permission to enable WPS mode (to enable local programming access to the panel via the installer app) and also initiate phone test.

Level 1: Supervisor/Administrator

Users assigned to this level have similar privileges to the Master Code user but are limited based on the partition assignment. This user can perform the following actions on the partitions they are assigned to:

l Arm/Disarm l Bypass/Unbypass l Enable/disable chime l Access home automation menu l View troubles, initiate a system test l Select a display language l View the event buffer l Program zone labels l Update WiFi SSID and password l Create new users l Program a duress code l Program user labels

Supervisor users can only add, edit or delete users assigned to the same partitions as they are.

Level 2: Basic/Standard User

Has permission to access basic security functions, including:

l Arm/disarm l Bypass/unbypass zones l Enable/disable chime l View system troubles l View alarm in memory

Level 3: Maintenance/Guest

Users assigned to this level are limited to an assigned partition and have reduced system access. These functions include:

l Arm/disarm l Enable/disable chime l View system troubles

Duress code:

Has access to all features of Basic/Standard user, including:

l Arm/disarm l Bypass/unbypass zones

When this code is used for any function, a duress code event will be generated.

User Name (label)

This option is used to program a system user name.

Default: Blank

Valid range: 32 character ACSII

4.7.3 Wireless Siren Configuration Options

The following section provides descriptions of all wireless siren programming options.

- 20 -

Page 24

Section 4: Programming Options

Siren Label

This option is used to program a label for the device.

Default: Siren 1

Valid range: 32 character ASCI

Siren Enable/Disable

This option is used to enable and disable the wireless siren.

Default: Enabled

Valid range: Enabled/Disabled

Siren Partition Assignment

This option is used to assign the wireless siren to an available partition.

Default: 1

Valid range: 1-4

Fire Alarm

When this option is enabled, the wireless siren sounds during fire alarms.

Default: Enabled

Valid range: Enabled/Disabled

CO Alarm

When this option is enabled, the wireless siren sounds during CO alarms.

Default: Enabled

Valid range: Enabled/Disabled

Burg Alarm

When this option is enabled, the wireless siren sounds during burglary alarms.

Default: Enabled

Valid range: Enabled/Disabled

Flood Alarm

When this option is enabled, the wireless siren sounds for flood alarms.

Default: Enabled

Valid range: Enabled/Disabled

Auto Tamper Alarm

When this option is enabled, the wireless siren sounds during tamper alarms.

Default: Disabled

Valid range: Enabled/Disabled

Activity LED

When this option is enabled, the Activity LED flashes every few seconds to indicate that the siren is enrolled and active.

Default: Disabled

Valid range: Enabled/Disabled

Volume Control

This option is used to control the volume of the wireless siren.

Default: Medium.

Valid range: Low, Medium, High

Squawk Control

This option is used to control wireless siren behavior during an alarm.

Default: Sounder Only

Valid range: Disabled, Sounder Only, Strobe Only, Sounder and Strobe

Exit/Entry Beeps

When this option is enabled, the wireless siren beeps whenever entry/exit zones are tripped.

Note: When set to Disable in Stay Mode, the siren still beeps on entry/exit when the system is armed in Away mode.

Default: Disabled

Valid range: Disabled, Enabled, Disable in Stay Mode

Siren Strobe Alarm

This option is used to control the behavior of the wireless siren strobe light during an alarm.

Default: Act ive Until Bell Time-out

Valid range: Disabled, Active Until Disarmed, Active Until Bell Time-out

4.7.4 Wireless Key Configuration Options

The following sections are used for programming wireless keys.

Wireless Key Enable/Disable

When this option is enabled, the alarm panel receives commands from the enrolled wireless key.

Default: Enabled

Valid range: Enabled/Disabled

Wireless Key Partition Assignment

This option is used to assign the wireless key to an available partition.

Default: 1

Valid range: 1-4, ALL

Wireless Key Button Programming

This option is used to program functionality for all available buttons on the wireless key. The number of buttons varies depending on the model.

Note: Panic shall be disabled for PGx929 and PGx939 for SIA installations.

- 21 -

Page 25

Section 4: Programming Options

Default: Button 1 = Away Arm*

Button 2= Stay Arm* Button 3= Disarm* Button 4= Panic** Button 5= Quick Exit

Valid

Null, Disarm, Stay Arm, Away Arm, Global Stay Arm, Global Away

range:

Arm, Global Disarm, Quick Exit, Auxiliary Alarm, Panic Alarm

*Not applicable for PGx938. **Not applicable for PGx938 and PGx949.

Supervision

This option is used to control battery supervision of the wireless key. When enabled, the iotega detects and reports a wireless key low battery condition. This feature is only applicable for PGx938.

Default: Disabled (Must be enabled for UL)

Valid range: Enabled/Disabled

User ID

All wireless keys are assigned to the Master user by default. Assignment to another user is done via the touchscreen keypad. Assigning wireless keys to specific users aids in tracking and logging system events. Not applicable for PGx938

Default: None

Valid range: 001-100

4.7.5 Wireless Smoke and CO Configuration Options

The following sections are used for programming wireless smoke and CO detectors.

Device Enable/Disable

This option is used to enable and disable wireless smoke and CO detectors.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to assign wireless smoke and CO detectors to an available partition.

Default: 1

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This programming option is used to program a zone type for the device.

Default: 24-hourstandard f ire

Valid range: 24-hour s tandard fire, Auto-verified fire

Device Label

This section is used to program a custom label for the device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Attribute

This section is used to customize zone behavior for the device. The table below specifies the status of each attribute for this device. See "Available Zone Attributes" on page 32 for attribute definitions.

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Disabled (read-only)

Transmission Delay Disabled (read-only)

Bell Audible Enabled (read-only)

Bell Steady Disabled (read-only)

Bypass Enable Disabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Disabled (read-only)

Two Way Audio Disabled (read-only)

Talk Listen Disabled (read-only)

Supervision

This section is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled (Must be enabled for UL)

Valid range: Enabled/Disabled

4.7.6 Wireless Glassbreak Configuration Options

The following sections are used for programming glassbreak detectors.

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to assign the wireless device to an available partition.

- 22 -

Page 26

Section 4: Programming Options

Default: 1

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This programming section is used to program a zone type for the device.

Default: Interior Follower

Valid

Instant, Interior Follower, Interior Stay/Away, Delay Stay/Away, 24

range:

Hour Supervisory Buzzer, 24Hour NonAlarm

Device Label

This section is used to program a custom label for the device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Attribute

Door Chime Enabled

Alarm Report Enabled

Burglary Verified Enabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Enabled (read-only)

Two Way Audio Enabled (read-only)

Talk Listen Enabled (read-only)

Supervision

This section is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled

Valid range: Enabled/Disabled

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Disabled

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This option is used to program a zone type for the device.

Default: 24-hourTemperature

Valid range: 24-hour Temperature

Device Label

This option is used to program a custom label for the wireless device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Attribute

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Disabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Disabled (read-only)

Two Way Audio Disabled (read-only)

Talk Listen Disabled (read-only)

4.7.7 Wireless Temperature Configuration Options

The following sections are used for programming wireless temperature sensors.

Supervision

This option is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

- 23 -

Page 27

Section 4: Programming Options

Default: Enabled

Valid range: Enabled/Disabled

Temperature Format

This section is used to select the scale temperature is displayed in.

Default: F

Valid range: F (Fahrenheit), C (Celsius)

High Temperature Warning

This option is used to set the temperature threshold for activating the High Temperature warning indicator. A high temperature warning sounds an audible alert but does not send a trouble to the central monitoring station. This option is disabled by entering -999 or 999.

Default: 999

Valid range: -999 to 999

High Temperature Alarm

This option is used to set the temperature threshold for activating the High Temperature alarm. This option is disabled by entering -999 or 999.

Default: 999

Valid range: -999 t o 999

Low Temperature Warning

This option is used to set the temperature threshold for activating the Low Temperature warning indicator. A low temperature warning sounds an audible alert but does not send a trouble to the central monitoring station. This option is disabled by entering -999 or 999.

Default: 999

Valid range: -999 t o 999

Low Temperature Alarm

This option is used to set the temperature threshold for activating the Low Temperature alarm. This option is disabled by entering -999 or 999.

Default: 999

Valid range: -999 t o 999

Device Partition Assignment

This option is used to assign the wireless device to an available partition.

Default: 1

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Disabled

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This programming section is used to program a zone type for the device.

Default: Interior Follower

Valid

Instant, Interior Follower, Interior Stay/Away, Delay Stay/Away, 24

range:

Hour Supervisory Buzzer, 24Hour NonAlarm

Device Label

This section is used to program a custom label for the device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Attribute

This option is used to customize zone operation. The following attributes are available for the temperature sensor:

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Disabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Disabled (read-only)

Bypass Enable Disabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Disabled (read-only)

Two Way Audio Disabled (read-only)

Talk Listen Disabled (read-only)

4.7.8 Wireless Flood Configurations

The following sections are used for programming wireless flood sensors.

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Supervision

This section is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled

Valid range: Enabled/Disabled

4.7.9 Wireless PIR CAM Configurations

The following sections are used to program wireless PIR Camera motion detectors.

- 24 -

Page 28

Section 4: Programming Options

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to assign the wireless device to an available partition.

Default: 1

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Device Label

This section is used to program a custom label for the device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Type

This programming section is used to program a zone type for the device.

Default: Interior Follower

Valid

Instant, Interior Follower, Interior Stay/Away, Delay Stay/Away, 24

range:

Hour Supervisory Buzzer, 24Hour NonAlarm

Zone Attribute

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Enabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Enabled (read-only)

Two Way Audio Enabled (read-only)

Talk Listen Enabled (read-only)

Supervision

This section is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled

Valid range: Enabled/Disabled

Alarm LED

This option is used to enable/disable the device’s onboard LED. When enabled, the LED activates when an alarm occurs.

Default: Enabled

Valid range: Enabled/Disabled

High Traffic Shutdown

Activating this feature helps conserve battery power when the system is disarmed by configuring a reporting timer. When motion is detected, the device transmits an alarm to the receiver and does not report any further events until the timer expires. Any motion detected during the configured period is reported once the timer expires. No Delay causes the device to report an alarm each time the detector is tripped.

Default: Not Active

Valid

Not Active, No Delay, 5Second Delay, 15 Second Delay, 30 Second

range:

Delay, 1 Minute Delay, 5 Minute Delay, 10Minute Delay, 20 Minute Delay, 60 Minute Delay

Event Counter

This option is used to set the number of alarm events required to activate the alarm.

Default: Low

Valid range: Low/High

Image Brightness

This option is used to lighten or darken the camera image.

Default: 0

Valid range: -3, -2, -1, 0, 1, 2, 3

Image Contrast

This option is used to lighten or darken the contrast of the camera image.

Default: o

Valid range: -3, -2, -1, 0, 1, 2, 3

Color

When this option is enabled, the camera captures color images. When disabled, the camera captures black and white images.

Default: Enabled

Valid range: Enabled/Disabled

High Resolution

When this option is enabled, the camera captures high resolution images (320 x 240 dpi). When disabled, image resolution is 160 x 128 dpi.

- 25 -

Page 29

Section 4: Programming Options

Default: Enabled

Valid range: Enabled/Disabled

Normal Quality

When this option is enabled, the camera captures lower resolution images (160 x 128 dpi).

Default: Disabled

Valid range: Enabled/Disabled

Audio (mic)

This option is used to enable/disable the built-in microphone on the device.

Default: Disabled

Valid range: Enabled/Disabled

4.7.10 Wireless PIR (NO CAM) Configurations

The following sections are used to program wireless motion detectors.

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This option is used to program a zone type for the device.

Default: Follower

Valid

Instant, Interior, Follower,Interior Stay/Away, Delay Stay/Away, 24

range:

Hour Supervisory Buzzer, 24Hour Non-Alarm

Device Label

This option is used to program a custom label for the wireless device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Zone Attribute

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Enabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Enabled (read-only)

Two Way Audio Enabled (read-only)

Talk Listen Enabled (read-only)

Supervision

This option is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled

Valid range: Enabled/Disabled

Alarm LED

This option is used to enable/disable the device’s onboard LED. When enabled, the LED activates when an alarm occurs.

Default: Enabled

Valid range: Enabled/Disabled

24 Hour PIR

This option is used to define if motion alarms are always enabled or only enabled at night.

Default: Enabled

Valid range: Enabled/Disabled

High Traffic Shutdown

Default: Not Active

Valid

Not Active, No Delay, 5Second Delay, 15 Second Delay, 30 Second

range:

Delay, 1 Minute Delay, 5 Minute Delay, 10Minute Delay, 20 Minute Delay, 60 Minute Delay

- 26 -

Page 30

Section 4: Programming Options

Detection Range

This option is used to select the sensitivity of the detector. The higher the sensitivity, the further the range of the detector.

Default: High

Valid range: Low, High, UL

4.7.11 Wireless Door Window Configurations

The following sections are used to program wireless door/window contacts.

Device Label

This option is used to program a custom label for the wireless device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Zone Type

This option is used to program a zone type for the device.

Default: 24-hour Temperature

Valid

Delay 1, Delay 2, Instant (Perimeter), Interior Follower, Interior

range:

Stay/Away, Delay Stay/Away, Day Zone, 24HourBurglary, 24Hour Silent Holdup, 24Hour AudiblePanic, 24Hour Medical Alarm, 24Hour Supervisory Buzzer, 24HourNon-Alarm

Device Partition Assignment

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: 1-4

Door Chime Disabled

Alarm Report Enabled

Burglary Verified Enabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Enabled (read-only)

Two Way Audio Enabled (read-only)

Talk Listen Enabled (read-only)

Supervision

This option is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Default: Enabled

Valid range: Enabled/Disabled

Alarm LED

This option is used to enable/disable the device’s onboard LED. When enabled, the LED activates when an alarm occurs.

Default: Enabled

Valid range: Enabled/Disabled

Reed Switch

This option is used to enable/disable the device’s built-in reed switch. The reed switch is used in conjunction with the separately mounted magnet as part of the trigger mechanism. If the reed switch is enabled and a device is hardwired to the external input terminals, both sensors transmit simultaniously. However, the iotega treats both devices as the same zone. Disable the reed switch to have the hardwired device funciton independently.

Default: Enabled

Valid range: Enabled/Disabled

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Attribute

Zone EOL Configuration

This option is used to configure end of line resistors for the external input terminals. The alarm panel uses EOL resistors to monitor for fault or alarm conditions.

Default: EOL Disable

Valid range: Single, EOL Disable, Normal Open, Normal Close

4.7.12 Wireless Shock Sensor Configurations

The following sections are used to program wireless shock sensors.

- 27 -

Page 31

Section 4: Programming Options

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

Device Partition Assignment

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: 1-4

Chime Tone

This option is used to select the tone emitted by the device when the zone is tripped.

Default: Beeps

Valid range: Beeps, Bing Bing, Ding Dong, Alarm Tone

Zone Type

This option is used to program a zone type for the device.

Default: Instant (Perimeter)

Valid range: 24 Hour Burglary, Day Zone, I nstant (Perimeter)

Device Label

This option is used to program a custom label for the wireless device.

Default: Zone ZZZ

Valid range: 32 character ASCII

Default: Enabled

Valid range: Enabled/Disabled

Alarm LED

This option is used to enable/disable the device’s onboard LED. When enabled, the LED activates when an alarm occurs.

Default: Enabled

Valid range: Enabled/Disabled

Reed Switch

Default: Disabled

Valid range: Enabled/Disabled

Zone EOL Configuration

This option is used to configure end of line resistors for the external input terminals. The alarm panel uses EOL resistors to monitor for fault or alarm conditions.

Default: EOL Disable

Valid range: Single, EOL Disable, Normal Open, Normal Close

Zone Attribute

Door Chime Enabled

Alarm Report Enabled

Burglary Verified Enabled

Transmission Delay Enabled

Bell Audible Enabled (read-only)

Bell Steady Enabled (read-only)

Bypass Enable Enabled (read-only)

Force Arm Disabled (read-only)

Swinger Shutdown Enabled (read-only)

Two Way Audio Enabled (read-only)

Talk Listen Enabled (read-only)

Supervision

This option is used to enable/disable wireless supervision of the device. Supervision monitors the presence of the wireless device on the alarm system.

Shock Accumulation

Shock accumulation is used to count a series of low level impacts that fall below the programmed alarm threshold (see Shock Sensitivity) over a ten-second period. If the total energy of the low level impacts surpasses the threshold, an alarm is triggered. If not, the accumulation level is reset.

Default: Enabled

Valid range: Enabled/Disabled

Shock Sensitivity Level

This option is used to adjust the sensitivity of the sensor. The lower the number, the more sensitive the device. Use the lowest settings for hard surfaces such as concrete.

Default: 8

Valid range: 1-19

4.7.13 Repeater Configuration Options

The following sections are used to program wireless repeaters.

- 28 -

Page 32

Section 4: Programming Options

Device Label

This section is used to program a custom label for the device.

Default: Repeater X

Valid range: 32 character ASCII

Device Enable/Disable

This option is used to enable and disable the wireless device.

Default: Enabled

Valid range: Enabled/Disabled

- 29 -

Page 33

4.8 Available Zone Types

Delay 1

Delay 2 Commonly assigned to secondary points of entry (further from t he k eypad). Follows entry delay 2timer.

Instant Commonly used for perimeter doors and windows, this zone type follows t he exit delay. The alarm is triggered inst antly if the zone is t ripped after the

Interior Commonly ass igned to interior motion sensors near a point of entry, such as afoyer or hallway, that must be access ed t o reach the keypad. The

Interior Stay/Away

Delay Stay/Away

Day Zone Commonly used in areas whereimmediate notification of entry is desired. Whendisarmed, tripping t his zone activates the k eypad buzzer but does

Commonly assigned to primary points of entry. Follows entry delay 1 andexit delay timers. Arming the alarm system starts the exit delay timer. After the exit delay has expired, opening the door starts the entry delay timer. During entry delay, the keypad buzzer prompts the user to disarm the system.

exit delay expires.

alarm is activated if the system is armed anda delay type zone (e.g., front door)is not tripped first , or if the entry/exit timer expires before the alarm is disarmed. Otherwise, the zoneis instant if t ripped.

Similar to I nterior zone type except that the s yst em bypasses the zone when armed in Stay mode. Commonly used to activate perimeter zones while permitt ing f ree movement throughout the interior.

Similar to delay 1 except that t he zoneis bypassed when armedin Stay mode. Commonly used with motion detectors that cover an entry point.

not log or report the event. When armed, trippingthis zone activates the sirenthen logs and reports the event.

Note: An alarm during exit delay causes the siren to activate and remain on when exit delayexpires.

Standard 24Hour Fire

Auto Verify Fire

This zone is used with smoke detectors. The siren sounds instantly when the smoke detector is activated. If enabled, the communicator immediately transmits the alarm to the monitoring station. A t amper or fault of this zone type causes a fire troubleto logand transmit.

This 24 hour zone ty pe v alidates analarm condition by looking for a second alarm transmission or the absence of an alarm restoral condition on wireless smoke detectors. When the zone is activated, a 40-second delay begins. If the zoneis still faulted after 40 seconds, the syst em goes into full alarm. The bell sounds and the event is logged and communicated. If another fire zone is activated during the auto verify sequence, alarms are immediately generated for all pending zones. This applies to all other fire zone ty pes and t o [F] key alarms. If the zone is no longer in alarm at the end of the 40 second delay, an 80-second verification t imer begins.If another f ire z one is activated during the auto v erify sequence, both zones go into alarm immediately.

Note: Wirelesssmoke detectors used with this zone type must have a built in siren to act as a pre-alert to the system alarm.

24-Hour CO This zone type is used with CO detectors. In the event of an alarm, a distinct ive siren cadence is sounded. This is followed by a 5-second pause and

24-Hour Burglary

24-Hour Holdup

24-Hour Panic

24-Hour Medical

24-Hour Supervisory

24-Hour Temperature

then repeated. After 4minutes, the 5-secondpause is extended to 60 seconds; however, BTO must be programmed with a value of 5 minutes or higher. The siren is silenced when an access code is entered or the siren times out.

This zone ty pe is active at all times. It reports an alarm if the alarm system is armed or disarmed. This zonetype sounds the siren for the length of Bell time-out if the audible attribute is enabled.

Instant alarm whenactivated, silent alarm at default.

Note: Not for use in UL listed installations.

Instant alarm whenactivated, audible alarm at default.

This zone is active and reports alarms at all times whentripped. Thesiren and keypad buzzer do not activate.

This zone ty pe is used with t emperature sensors and is activated when t he temperature rises above a programmed threshold. Instant alarm when activated, audible alarm at default. This z one type generates an alarm when the system is armed or disarmed.

Note: The temperature threshold includesa 3 °C (5-6 °F) difference between a given state and its restored condition. For example, an alarm at 6 °C isrestored at 3°C (High temperature) or 9°C (Low temperature), depending upon the zone typeselected.

24-Hour Flood

24-Hour NonAlarm

Instant alarm whenactivated, audible alarm at default.

This zone is active at alltimes but does not cause an alarm. Zone att ributes such as Zone Bypassing andDoor Chime affect the functionality of this zone. This z one type can also beassigned t o atemperature s ensor if indoor/outdoor temperature display is required without temperaturewarnings or alarm conditions.

Regulatory Agency Statements

FCC MODIFICATION STATEMENT

Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment.

- 30 -

Page 34

Digital Security Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.

ISED CANADA INTERFERENCE STATEMENT

This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, ême si le brouillage est susceptible d'en compromettre le fonctionnement.

FCC CLASS B DIGITAL DEVICE NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or experienced radio/television technician for help.

CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.

The reference to the WS900-xx throughout this manual is applicable to the following model numbers: WS900-19 and WS900-29. FCC ID:F5316WS90019 FCC ID:F5316WS900-29 IC: 160A-WS90019 IC: 160A-WS90029

FCC/ISED CANADA WIRELESS NOTICE

This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 m between the radiator and your body. Antenna gain must be below:

Fre quency band 3G7090

GSM 850 / FDD V 2.1 dBi

PCS1900 / FDD II 3.7 dBi

Fre quency band LT7090

LTE B4 (1700 MHz) 1.5 dBi

LTE B13 (700 MHz) 2.2 dBi

This transmitter can be co-located or operating in conjunction with any other antenna or transmitter.

The reference to the Cellular Communicator xx7090 throughout this manual is applicable to the following model numbers: 3G7090 and LT7090. FCC ID:F53163G7090 FCC ID:F5316LT7090 IC: 160A-3G7090 IC: 160A-LT7090

WARNING: To satisfy FCC RF exposur e requirements for mobi le transmitting devices, a separation d istance of 20cm or more must be maintained between the antenna of this device and persons dur ing device operation.

NIST Validationof encryption algorithm AES128 certificateNo. 4053

FCC/IC LABEL

- 31 -

Page 35

The modular transmitter 3G7090 or LT7090 is labeled with its own FCC ID and IC number. When the module is installed inside the host device WS900-19 or WS900- 29 and the FCC ID/IC of the module is not visible, the host device displays the provided label referring to the FCC ID and IC of the enclosed module. This label is shipped together with the module and it is the responsibility of the integrator to apply it to the exterior of the enclosure, as displayed in the following figure.

4.9 Available Zone Attributes

The following table defines each available zone attribute.

Alarm Report When this attribute is enabled, z one alarm andrestore events are transmitted. When disabled, zone alarm events are not transmitt ed but are logged to

Chime When this attribute is enabled, t he keypadchimes when the zone is opened or closed.

Burglary Verified

Transmission Delay

Bell Audible The sirenactivates onalarm. This is a read-only option.

Bell Steady Siren output is steady rather thanpulsed when in alarm. This is a read-only option.

Bypass Enable

Force Arm The s yst em can be armedwith the zone open. The zone is t emporarily bypass ed and, when secured, is monitored by the syst em. If Open Zone

Swinger Shutdown

Two-Way Audio

Talk Listen The central station operator and the end user can communicate t hrough the panel's microphone and speaker. This is a read-only option.

the event buffer.

When this attribute is enabled, zone alarms are not communicated until a burglary verified event occurs.

When this attribute is enabled, reporting of zone alarms is delayed for t he programmed time. If a valid access code is entered within this time, no alarm signal is communicated. When disabled, reporting codes are transmitted immediately.

Zones can be manually bypassed. This is a read-only option.

Cancels Armingis enabled, t he s ystem can begin arming with an open, Force Arm zone, but if the zone is still openwhen the exit delay timer expires, arming is cancelled. This is a read-only option.

A zone that goes into alarm for the numberof times programmed in the Swinger Shutdown Counter shuts down with no further transmissions sent to the monitoring station. The sirenfollows swinger shutdown if programmed. This is a read-only option.

The panel is able to initiate a 2-way audio session. This is a read-only option.

- 32 -

Page 36

4.10 Diagnostics - Read Only

Radio Version#

This section displays the software version of the cellular radio.

Primary Telephone Number

This section displays the cellular telephone number of the SIM.

IMEI number

This section displays the unique 15-digit International Mobile Equipment Identity (IMEI) of the radio. The format of the IMEI is: Reporting Body Identifier (2 digits), Allocation Number (4 digits); Final Assembly Code (2 digits); Serial Number (6 digits); and a check digit.

SIM Number

This section displays the Subscriber Identity Module (SIM) number of the SIM card installed in the communicator. The format of the SIM number is: Major Industry Identifier (2 digits); Mobile Country Code (2 or 3 digits); Mobile Network Code (2 - 3 digits); Unique Number (10 -12 digits); and Checksum (1 digit). Valid SIM numbers range is: 18 - 21 numbers. This number is printed on the SIM and the outside of the communicator carton.

Note: The checksum digit is omitted on 19-digit SIM card numbers.

Cellular Device Type

This section displays the type of cellular module used by the system. E.g., UE910-N3G, LE910-SVG

Cellular Signal Strength

This section displays the strength of the cellular signal: Strong, Weak, None.

Radio Network Technology

This section displays the mobile wireless telecommunications technology used by the cellular radio.

Provider ID#

This section identifies number of the telecommunications service provider.

4.11 System Control

Use this section to perform the following diagnostic tests.

System Test

This test is used to check that the iotega‘s siren and LEDs are operating correctly. This is a hardware test only. No signals are transmitted to the monitoring station. During the test, the LEDs flash.

Alarm Control Panel Placement Test

This test is used to check the panel location for signal noise that could interfere with the proper operation of the alarm system. If the location is good, “No noise” is displayed. If the location has signal noise beyond system tolerance, “noise” is displayed.

Walk Test

This mode tests the operation of each detector in the system. While in Walk Test, the Ready, Armed, and Trouble LED's on the keypad flash to indicate that the test is active. When a zone is violated during the test, a 2-second tone sounds on all system keypads to indicate that the zone is working correctly. The system automatically ends the test after 15 minutes without zone activity. An audible warning (5 beeps every 10 seconds) is sounded, beginning 5 minutes before the test ends.

- 33 -

Page 37

Placement Test

This test is used to determine the RF signal status for wireless devices and can be performed on the installer portal or at the individual device. For instructions on placement testing at the device, refer to the installation sheet included with the wireless equipment. Two test results are provided: 24 Hour: The iotega displays RF test results from the enrolled device received over a 24 hour period. Now: The iotega displays RF test results from the last placement test.

Note: For vanishing door contacts and wireless keys, the device must be triggered in order to get a result.

Status Defini tion

Strong Strong signal strength

Good Goodsignal strength

Poor Poor signal strength

1-Way The alarm panel can see the device but cannot configureor c ontrol it.

2-Way The alarm panel can configure and control the device.

0-Way The alarm panel cannot see or control the device.

Missing The device has not received any communications from the panel during the supervision monitoring period.

Not Networked The device is registered but not activated on the network.

NA The device is not registered.

4.11.1 Network

Cellular Test Transmission

Ethernet and Cellular test transmissions check to see if the selected communication path between the iotega and the central monitoring station is functioning correctly. Both Ethernet/Cellular 1 (primary receiver) and Ethernet/Cellular 2 (secondary receiver) can be tested separately based on individual reporting configurations. Test transmissions can also be configured to alternate between primary and secondary receivers. For details, see "Alternate Test Transmission" on page 1. Test transmission time and test transmission cycle can be programmed for both primary and secondary receivers. See "Central Monitoring Station Programming Options" on page 17 for more details.

- 34 -

Page 38

Section 5: Troubleshooting

5.1 Testing

l Power up the system l Program options as required (see programming section) l Trip then restore zones l Verify correct reporting codes are sent to the central monitoring station

5.2 Viewing Troubles from the Integrated Keypad

1. Move your hand over the iotega to illuminate the keypad.

2. Press * 2 .

3. Enter your access code if required. The Trouble LED on the keypad flashes if an access code is needed to view troubles. Entering a valid access code silences trouble beeps.

4. The keypad displays top-level troubles present on the system by illuminating numbers on the keypad. Refer to the table below for the meaning of each trouble code. When in the top level trouble display, the trouble LED flashes once, pauses, then repeats.

5. If additional details are available for the trouble, the [*] key illuminates. Press any illuminated number to display the second level troubles.

6. The keypad displays a second level of detail for the trouble code selected in step 5 by illuminating numbers on the keypad. Refer to the table below for the meaning of each trouble code. When in the second level trouble display, the trouble LED flashes two times, pauses, then repeats.

7. If additional details are available for the trouble, the [*] key illuminates. Press any illuminated number to display the third level trouble detail.

8. The keypad displays the device number with the trouble condition. If more than one device has this trouble at the same time, the keypad cycles though each one. When in the third level trouble display, the trouble LED flashes three times, pauses, then repeats.

9. Press the [*] key to acknowledge a trouble.

Note: Pressing the # key returns you to the previous level. Pressing the # key while in the top-level exits the trouble menu.

Trouble Summary

l Trouble [01] - System Trouble l Trouble [02] - Zone l Trouble [03] - Siren l Trouble [04] - Keypad l Trouble [05] - Repeater l Trouble [06] - Wireless Key l Trouble [07] - Communication l Trouble [00] - Integrator Trouble

Table 7-1 Trouble Indications

1stLayer 2ndLayer 3rdLayer

01 System Trouble 01 AC

02 Battery Trouble 03 Tamper 04 Hardware Fault 05 Loss of Time 06 RF Jam

02 Zone 01 AC Trouble 1-128

02 Battery Trouble 1-128 03 Tamper 1-128 04 Fault (Supervision) 1-128

- 35 -

Page 39

Section 5: Troubleshooting

05 Not Networked 1-128 06 Fire/CO Trouble 1-128

03 Siren 01 Future Use 1-16

02 Battery Trouble 1-16 03 Tamper 1-16 04 Fault (Supervision) 1-16 05 Not Networked 1-16

04 Keypad 01 AC 1-9

02 Battery Trouble 1-9 03 Tamper 1-9 04 Fault (Supervision) 1-9 05 Not Networked 1-9

05 Repeater 01 AC 1-8

02 Battery Trouble 1-8 03 Tamper 1-8 04 Fault (Supervision) 1-8 05 Not Networked 1-8 06 RF Jam 1-8

06 Wireless Key 01 Future Use 1-32

02 Battery Trouble 1-32 03 Future Use 1-32 04 Future Use 1-32 05 Not Networked 1-32

07 Communication 02 FTC Trouble

04 Cellular Trouble 05 Ethernet/WiFi Trouble

00 Integrator Trouble 01 Z-Wave Trouble

- 36 -

Page 40

Appendix 8: Reporting Codes

The following tables contain Contact ID and Automatic SIA format reporting codes.

Contact ID

Each of the digits indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the event code contains [34]. The central monitoring station would receive the following: *BURG - ENTRY/EXIT - 1 where the “1” indicates which zone went into alarm. see "Contact ID and SIAZone Alarm/Restore Event Codes" on page 37 for code definitions.

SIA Format - Level 2 (Hard Coded)

N ri1 BA 01 N = New Event ri1 = Partition /Area Identifier BA = Burglary Alarm 01 = Zone 1

A system event uses the Area Identifier ri00.

Contact ID and SIAZone Alarm/Restore Event Codes

Sec tion # Definition Dialer Dir-

ection*

Sensor Events

Sensor alarms A/R see "Contact ID & SIA Zone Alarm/Restore Event Codes" on

Sensor restores A/R

Sensor tamper/restore MA/R E(3)83-ZZZ / R(3)83-ZZZ TA-ZZZ / T R-ZZZZ

Sensor trouble/restore MA/R E(3)8A-ZZZ / R(3)8A-ZZZ UT-ZZZZ / UJ-ZZZZ

Tamper Events

Sensor tamper/restore T/R E(3)17-000/ R(3)17-000 ES-000 / TR-000

Paneltamper/restore T/R E(1)37-000 / R(1)37-000 ES-000 / EJ-000

Touchpad tamper - keystroke T/R E(4)61-000 JA-000

Automatic Contact ID Codes

page 38" for details.

SIA Auto Rep Codes**

Opening Events

Opening report O/C E(4)A1-UUU OP-UUUU

Closing Events

Closing report O/C R(4)A1-UUU CL-UUUU

Partial closing O/C E(4)56-000 CG-0000

Exit alarm O/C E(3)74-ZZZ EA-ZZZZ

System Troubl e Events

Sensor tamper/restore MA/R E(1)37-000/ R(1)37-000 ES-0000/EJ-0000

CPU low battery trouble/restore MA/R E(3)A2-000 / R(3)A2-000 YT-0000 / YR-0000

Battery absent t rouble/restore MA/R E(3)11-000/ R(3)11-000 YM-0000 / YR-0000

Battery chargingtrouble/restore MA/R E(3)14-000/ R(3)14-000 YP-0000/ YQ-0000

AC power fail/restore MA/R E(3)A1-000 / R(3)A1-000 AT-0000 / AR-0000

Communication

Receiver jammed/restore MA/R E(3)AA-001

Dual path supervision f ailure/restore MA/R E(3)500-xxx

FTC trouble/restore MA/R E(3)54-RRR/ R(3)54-RRR YC-RRR/YK-RRR

2-Way voice session start MA/R E(6)06 LF-000

Sensor Events

Sensor low battery trouble/restore. MA/R E(3) 84-ZZZ

R(3)AA-001

YX-0001 / YZ-0001

YS-0001 / YZ-0001

R(3)500-xxx

XT-ZZZZ / XR-ZZZZ

R(3) 84-ZZZ

- 37 -

Page 41

Appendix 8: Reporting Codes

Sec tion # Definition Dialer Dir-

ection*

Sensor trouble/restore MA/R E(3)8A-ZZZ

Sensor bypass/restore MA/R E(5)7A-ZZZ

Heat or probe trouble/restore MA/R E(3)8A-ZZZ

Freeze ESM module/restore MA/R E(3)8A-ZZZ

Repeater 1-8 AC fail/restore MA/R E (3)A1-901

RF jam t rouble/restore E(3)AA-0000

Miscellaneous Al arms

Duress zlarm -code entered at keypad A/R E(1)21-000 HA-0000/ HH-0000

Opening after alarm - disarmed with alarm in memory A/R E(4)58-000 OR-0000

Recent closing - alarm occurs within two minutes of system arming

Cross zone alarm A/R E(1)39-000 BV-0000

Two trip error A/R E(3)78-000 BG-0000

Cancel report A/R E(4)A6-UUU OC-UUUU

Prior ity Alarm and Restoral Events

[F] Key alarm/restore A/R E(1)1A-000

[A] Key alarm/restore A/R E(1)AA-000

[P] Key alarm/restore A/R E(1)2A-000

Silent police panic/cancel A/R E(1)20-0000/ R(1)20-0000 PA-0000/PH-0000

Miscellaneous Cl osing

Sensor bypass O/C E(5)7A-ZZZ UB-ZZZZ

Sensor bypass restore O/C R(5)7A-ZZZ UU-ZZZZ

A/R E(4)59-UUU CR-UUUU

Automatic Contact ID Codes

R(3)8A-ZZZ

R(5)7A-ZZZ

R(3)8A-ZZZ

R (3)A1-901

R(3)AA-000

R(1)1A-000

R(1)AA-000

R(1)2A-000

SIA Auto Rep Codes**

UT-ZZZZ / UJ-ZZZZ

UB-ZZZZ / UU-ZZ ZZ

KT-ZZZZ / KJ-ZZZZ

ZT-ZZZZ / ZJ-ZZZ Z

AT-0901 / AR-0901

XQ-0000/XH-0000

FA-0000 / FH-0000

MA-0000 / MH-0000

PA-0000 / PH-0000

Testing

Sensor test start/end T E(6)A7-UUU

R(6)A7-UUU

Auto-phone t est T E(6)A2-000 RP-0000 / RY-0000

Test transmission with trouble T E(6)A8-000 RY-0000

Manual phone test T E(6)A1-000 RX-0000

Maintenance

Partition f ire trouble/restore MA/R E(3)73-992

R(3)73-992

Smoke detector low s ensitivuty trouble/restore MA/R E(3)73-000

R(3)73-000

Panelprogramming MA/R E(6)27-000 LB-0000

Panelprogramming exited MA/R E(6)28-000 LS-0000

Lack of usage MA/R E(6)54-000

R(6)54-000

* A/R =alarms/restores; T/R = tampers/restorers; O/C = openings/closings; MA/R = maintenance alarms/restores; T =t est transmiss ions

** UUU = user number. Note t hat for CID, enter 999 f or user 1000. ZZZ/ZZZZ = zone number.

*** Zones and panic pendants are identified, wireless keys can be identified f or openings andclosings.

TS-UUUU/TE-UUUU

FT-992 / FJ-992

FT-0000 / FJ-0000

CD-000

Contact ID & SIA Zone Alarm/Restore Event Codes

(as per SIA DCS: ‘Contact ID’ 01-1999): The table below defines the meaning of all Contact ID and SIA zone alarm/restore event codes.

- 38 -

Page 42

Appendix 8: Reporting Codes

Zone Definition SIA Auto Rep Codes Contact ID Auto Rep Codes

Delay 1 BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ

Delay 2 BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ

Instant BA-ZZZZ / BH-ZZZZ E(1) 3A- ZZZ / R(1)3A- ZZZ

Interior BA-ZZZZ / BH-ZZZZ E(1) 3A- Z ZZ / R(1)3A-ZZZ

Interior stay/away BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ

Delay stay/away BA-ZZZZ / BH-ZZZZ E(1) 3A- ZZZ / R(1)3A- ZZZ

Day Zone BA-ZZZZ / BH-ZZZZ E(1) 3A- ZZZ / R(1)3A- ZZZ

24-Hr. Burglary BA-ZZZZ / BH-ZZZZ E(1) 3A- ZZZ / R(1)3A- ZZZ

Standard 24-Hr. Fire (wireless) FA-ZZZZ / FH-ZZZ Z E(1) 1A - ZZZ / R(1)1A- Z ZZ

24-Hr Temperature KA-ZZZZ / KH-ZZZZ E(1) 58- ZZZ / R(1)58 - ZZZ

24-Hr. Non alarm (walk test only) BA-ZZZZ / BH-ZZZZ E(1) 3A - ZZZ / R(1)3A- ZZZ

24-Hr. Supervisory buzzer UA-ZZZZ / UH-ZZ ZZ E(1)5A - ZZZ / R(1)5A - ZZZ

24-Hr. Auto verified fire (wireless) FA-ZZZZ / FH-ZZZZ E(1) 1A- ZZZ / R(1)1A - ZZZ

24-Hr. CO alarm GA-ZZZZ / GH-ZZZZ E(1)62 - ZZZ / R(1)62 - ZZZ

24-Hr. Holdup HA-ZZZZ / HH-ZZ ZZ E(1)22 - ZZZ / R(1)22 - ZZZ

24-Hr. Panic PA-ZZZZ / PH-ZZZZ E(1) 2A- ZZZ / R(1)2A - ZZZ

24-Hr. Flood WA-ZZZZ / WH-ZZZZ E(1) 54 -ZZZ / R(1)54 - ZZZ

24-Hr. Auxiliary MA-ZZZZ / MH-ZZZZ E(1) AA - ZZZ / R(1)AA - ZZZ

ZZZ/ZZZZ = zones 001-128

- 39 -

Page 43

Appendix 1: Guidelines for Locating Smoke Detectors and CO Detectors

Figure 1

Figure 2

Figure 3

Appendix 1: Guidelines for Locating Smoke Detectors and CO

Detectors

The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke and CO alarms.

Smoke Detectors

Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home. The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke alarms. It is recommended that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not protected by the required units. On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate national standards for installation recommendations.

l Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may pre-

vent the unit from detecting smoke.

l Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector

may prevent smoke from entering the unit.

l Do not locate detectors in areas of high humidity. l Do not locate detectors in areas where the temperature rises above 38°C (100°F) or falls below 5°C (41°F).

Smoke detectors should always be installed in USA in accordance with Chapter 29 of NFPA 72, the National Fire Alarm Code: 29.5.1.1. Where required by other governing laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows:

1. In all sleeping rooms and guest rooms.

2. Outside of each separate dwelling unit sleeping area, within 21 ft (6.4 m) of any door to a sleeping room, with the dis-

tance measured along a path of travel.

3. On every level of a dwelling unit, including basements.

4. On every level of a residential board and care occupancy (small facility), including basements and excluding crawl

spaces and unfinished attics.

5. In the living area(s) of a guest suite.

6. In the living area(s) of a residential board and care occupancy (small facility).

- 40 -

Page 44

Appendix 1: Guidelines for Locating Smoke Detectors and CO Detectors

Figure 3a

Figure 4

GROUND FLOOR

BASEMENT

KITCHEN

GARAGE

BEDROOM

CARBON MONOXIDE DETECTOR

Figure 5

Carbon Monoxide Detectors

Carbon monoxide is colorless, odorless, tasteless, and very toxic. It also moves freely in the air. CO detectors can measure the concentration and sound a loud alarm before a potentially harmful level is reached. The human body is most vulnerable to the effects of CO gas during sleeping hours; therefore, CO detectors should be located in or as near as possible to sleeping areas of the home. For maximum protection, a CO alarm should be located outside primary sleeping areas or on each level of your home. Figure 5 indicates the suggested locations in the home.

Do NOT place the CO alarm in the following areas:

l Where the temperature may drop below -10ºC or exceed 40ºC l Near paint thinner fumes l Within 5 feet (1.5m) of open flame appliances such as furnaces, stoves and fireplaces l In exhaust streams from gas engines, vents, flues or chimneys l Do not place in close proximity to an automobile exhaust pipe; this will damage the detector

PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING INSTRUCTION SHEET FOR SAFETY INSTRUCTIONS AND EMERGENCY INFORMATION.

Household Fire Safety Audit

Read this section for important information about fire safety. Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be conducted and a fire escape plan be developed.

1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or household service, have a professional evaluate these units.

2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area? Cleaning with flammable liquids should be avoided.

3. Are fire-hazardous materials (e.g., matches) well out of reach of children?

4. Are furnaces and wood-burning appliances properly installed, clean and in good working order? Have a professional evaluate these appliances.

Fire Escape Planning

There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed.

1. Every family member should participate in developing the escape plan.

2. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes from sleeping quarters.

3. Escape from a bedroom must be possible without opening the interior door.

Consider the following when making your escape plans:

- 41 -

Page 45

Appendix 1: Guidelines for Locating Smoke Detectors and CO Detectors

l Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their

locking mechanisms operate smoothly.

l If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue should be

developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning signal.

l If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use. l Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in winter; outdoor

furniture or equipment should not block exits.

l Each person should know the predetermined assembly point where everyone can be accounted for (e.g., across the

street or at a neighbour’s house). Once everyone is out of the building, call the fire department.

l A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings

as this can waste valuable time. Once outside, do not re-enter the house. Wait for the fire department.

l Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know

what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes to the building’s construction.

l Make sure your fire warning system is operational by conducting weekly tests. If you are unsure about system oper-

ation, contact your installer.

l We recommend that you contact your local fire department and request further information on fire safety and escape

planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection.

- 42 -

Page 46

Appendix 2: Regulatory Information

This product has been tested and found in compliance with the following standards:

l UL1023 Household Burglar-Alarm System Units l UL985 Household Fire Warning System Units l ULC-S545-02 Residential Fire Warning System Control Units l ORD-C1023-1974 Household Burglar-Alarm System Units

This product has also been tested and found in compliance with the ANSI/SIA CP-01-2014 Control Panel Standard – Features for False Alarm Reduction. This product is UL/ULC listed under the following categories:

l UTOU/UTOUC Control Units and Accessories, Household System Type l NBSX/NBSXC Household Burglar Alarm System Units l AMTB Control Panels, SIA False Alarm Reduction

The product is labeled with the UL and ULC listing marks along with the SIA CP-01 compliance statement (Also Classified in accordance with SIA-CP-01 Standard) as proof of compliance with the above mentioned standards. For further information on this product’s listings please also refer to the official listing guides published at the UL web site (www.ul.com) under Certifications Section. UL/ULC Residential Fire and Burglary Installations: For ULC Installations refer to the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540.

l Use at least one PG9916 or PG9926 Smoke Detector for Fire Installations (refer to Installer portal > Panel Settings>

Zones> Add Device (Enter Device Serial # or Auto Enroll) > Type >Standard Fire)

l The entry delay shall not exceed 60 seconds (refer to Installer portal > Panel Settings>Panel Configuration>Partition

Configuration> Entry Delay 1)

l The exit delay shall not exceed 120 seconds (refer to Installer portal > Panel Settings>Panel Configuration>Partition

Configuration> Exit Delay)

l The minimum Bell Time-out is 4 minutes (refer to Installer portal > Panel Settings>Panel Configuration>System Con-

figuration> Burglary Bell Time-out)

Note: For ULC Residential Fire Installations the minimum Bell Time-out is 5 minutes

l Temporal Three Fire Signal shall be enabled (hardcoded ON) l Arm/Disarm Bell Squawk shall be enabled when using wireless key PG9929, PG9939 or PG9949 (refer to Installer

portal > Panel Settings>Panel Configuration>System Configuration> > Local arm shall be ON)

l A code shall be required for bypassing (refer to Installer portal >Panel Settings>Panel Configuration>System Con-

figuration> Access Code Is Required for Bypassing)

l Trouble beeps shall be enabled (refer to Installer portal >Panel Settings>Panel Configuration>System Con-

figuration> Trouble Beeps Auto Silence)

Note: This product is programmed to perform 5 attempts for communication of an event to the supervising station. If unsuccessful, a Fail To Communicate (FTC) trouble is generated.

l Test transmission cycle shall be set for monthly transmission (refer to Installer portal > Panel Settings>Panel Con-

figuration>Comms Configuration> Ethernet Test Transmission Cycle & Cellular Test Transmission Cycle)

l For UL installations, 2 repeaters (model PG9920) must be used for proper signal routing.

Note: For ULC Residential installations set for daily test transmission

l Wireless Supervision window shall be enabled (refer to Installer portal > Account Details > Panel Configuration > Eth-

ernet Supervision, Cellular Supervision)

l Wireless Supervision window shall be set to 4 hours for Fire Installations (refer to Installer portal > Panel Set-

tings>Panel Configuration>Comms Configuration > Ethernet Supervision, Cellular Supervision)

l Wireless Supervision window shall be set to 24h for Burglary Installations only (refer to Installer portal > Panel Set-

tings>Panel Configuration>Comms Configuration > Ethernet Supervision, Cellular Supervision)

l RF Jam detection shall be enabled (refer to Installer portal > Panel Settings>Panel Configuration>System Con-

figuration> RF Jam Detection and Reporting)

l Bells will be active During 2-way Audio (refer to Installer portal > Panel Settings > Panel Configuration > System Con-

figuration > Wireless Siren Control)

l New Alarms will Disconnect 2-way Audio (refer to Installer portal > Panel Settings > Panel Configuration > System

Configuration > New Alarms Disconnect 2-way Audio for 2G)

l When the 2- way audio feature is enabled(refer to Installer portal > Panel Settings > Zones > 2-Way Audio) ensure

that New alarms will not Disconnect 2-Way Audio is OFF and Wireless Siren During 2-Way Audio is ON

- 43 -

Page 47

Appendix 2: Regulatory Information

Programming

The notes in the programming sections describing the system configurations for UL/ULC listed installations shall be implemented.

Bell Location

The alarm sounding device (bell) shall be located where it can be heard by the person operating the security system during the daily arming and disarming cycle.

Casual Users

The installer should caution the user(s) not to give system information (e.g., codes, bypass methods, etc.) to casual users (baby-sitters or service people).

User Information

The installer should advise the users and note in the User’s Manual:

l Service organization name and telephone number l The programmed exit time l The programmed entry time l Test system weekly

Regulatory Agency Statements

FCC MODIFICATION STATEMENT

Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Digital Security Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.

ISED CANADA INTERFERENCE STATEMENT

FCC CLASS B DIGITAL DEVICE NOTICE

- Reorient the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or experienced radio/television technician for help.

CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003.

The reference to the WS900-xx throughout this manual is applicable to the following model numbers: WS900-19 and WS900-29. FCC ID:F5316WS90019 FCC ID:F5316WS900-29 IC: 160A-WS90019 IC: 160A-WS90029

- 44 -

Page 48

Appendix 2: Regulatory Information

FCC/ISED CANADA WIRELESS NOTICE

Fre quency band 3G7090

GSM 850 / FDD V 2.1 dBi

PCS1900 / FDD II 3.7 dBi

Fre quency band LT7090

LTE B4 (1700 MHz) 1.5 dBi

LTE B13 (700 MHz) 2.2 dBi

This transmitter can be co-located or operating in conjunction with any other antenna or transmitter.

NIST Validationof encryption algorithm AES128 certificateNo. 4053

FCC/IC LABEL

- 45 -

Page 49

SIA False Alarm Reduction Installations: Quick Reference

Caution

Fire Alarm Verification feature (Auto Verified Fire Zone) is supported on the DSC Wireless Smoke Detector, Model PGx916 and PGx926. The fire alarm delay is 40s.

Notes:

Programming at installation may be subordinate to other UL requirements for the intended application. Cross zones have the ability to individually protect the intended area (e.g. motion detectors which overlap). Cross zoning is not recommended for line security Installations nor is to be implemented on exit/entry zones. There is a communication delay of 30 seconds in this control panel. It can be removed, or it can be increased up to 45 seconds at the option of the end user by consulting with the installer. The security system shall be installed with the sounding device activated and the communicator enabled for transmission using SIA or CID format.

SIA Feature Programming Section

Exit Delay Panel Settings>Panel Configuration>Partition Configuration> Exit Delay (select 45s, 60s, 90s, or 2 min)

Exit Time Restart (hardcoded ON) Enables the exit delay restart feature Default: Enabled Required

Auto Stay Arm on Un-vacated Premises Zones must be programmed as stay/Away

Entry delay(s) Panel Settings>Panel Configuration>Partition Configuration > Entry Delay (select 30s, 45s, 60s, 2mins, 3mins or 4mins)

Abort Window for Non-Fire zones Transmission Delay zone attribute must

Abort Window Time for Non-Fire zones Panel Settings>Panel Configuration>System Configuration > Communication Delay

Abort Annunciation An audible tone is generated when an

Communications Canceled Window Panel Settings>Panel Configuration>System Configuration>Communication Cancel Window

Comments Range/Default Requirement

Access to Entry and Exit delays and Bell Time Out for the system

Function Key: Stay Arming. All Stay/Away type zones will be automatically bypassed

Access to Entry and Exit delays and Bell Time Out for the system Note: Combined Entry delay and Communications Delay (Abort Window) shall not exceed 60s

be enabled

Access to the programmable delay before communicating alarms Note: Combined Entry delay and Communications Delay (Abort Window) shall not exceed 60s

alarm is aborted during the Abort window

Access to the programmable Cancel Window.

Range: 45- 120 sec. Default: 60 sec.

If no exit after full arm Default: Enabled

Range: 30 sec. to 4 min. Default: 30 sec.

May be disabled by zone or zone type Default: Enabled

Range: up to 45 sec. Default: 30 sec.

Annunciate that no alarm was transmitted Default: Enabled

Range: minimum 5 min. Default: 5 min. Note: minimum 5 min. for UL installations

Required (programmable)

Required

Required (programmable)

Required

Required (programmable)

Required

- 46 -

Page 50

SIA Feature Programming Section

Cancel Annunciation Panel Settings>Panel Configuration>System Configuration> > Reporting

Duress Feature Do not derive code from an existing

Cross Zone Timer Panel Settings>Panel Configuration>Partition Configuration >Cross Zone Delay

Swinger Shutdown for Alarms Panel Settings>Zones> Swinger Shutdown

24 hour auto verified Fire Access to 24 hour auto verified Fire Activates If a restore is Not

Comments Range/Default Requirement

Access to the reporting code for Alarm Canceled

Master/User code (e.g., Master code is 1234, the duress code should not be 1233 or 1235)

Access to the programmable Cross Zone timer

Access to the swinger shutdown limit for zone alarms.

Annunciate that a Cancel was transmitted. Default: Enabled

No automatic derivative of another user code. No duplicates with other user codes Default: Disabled

May program Range: 001255 seconds. Default: 0 seconds

For all non-fire zones shutdown at 1 or 6 trips Default: 2 trips

received within the specified time Default: disabled

Required

Allowed

Required (programmable)

Required

System Test: Panel Settings> Diagnostics> System>System Test

Panel Settings> Diagnostics> System> Device> Begin Walk Test

The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on. Refer to the User Manual.

This mode is used to test each zone on the system for proper functionality.

- 47 -

Page 51

Appendix 3: EULA

IMPORTANT - READ CAREFULLY: DSC Software purchasedw ith or without Products and Components is copyrightedand is purchased under the following license terms: This End-User License Agreement(“EULA”) is alegal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, adivisi on of Tyco Safety Products Canada Ltd.(“DSC” ), the manufacturer of the integratedsecurity systems and thedeveloper of the software andany relatedproducts or components (“HARDWARE”) which You acquired. If the DSC software product(“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may includeassociated media, printed materials, and “online” or electronic documentation. Any software provided alongw ith the SOFTWARE PRODUCT thatis associated with aseparate end-user licenseagreement is licensedto You under the terms of that l icenseagreement. By installing, copying, downloading, storing, accessingor otherwise using the SOFTWARE PRODUCT, You agreeunconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a m odification of any previous arrangement or contract. If You do not agreeto the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no r ight to use it.

SOFTWARE PRODUCT LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE Th is EULA grants You the f ollowing rights: Software Installation and Use- For each license You acquire, You may have only one copy of

theSOFTW ARE PRODUC T installed. Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or usedconcurrently on or from differentcomputers, includinga workstation, terminal or other digital electronic device (“ Device”). In other words, if You haveseveral workstations, You will haveto acquire a license for each workstation where the SOFTWARE will be used. Backup Copy - Youm ay m ake back-upcopies of the SOFTWARE PRODUCT, but You may only have onecopy per licensei nstalled at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printedm aterials accompanyingthe SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS Limitations on ReverseEngineering, Decompilation and Disassembly - Youm ay not reverse engineer, decompile, or disassemble the SOFTWARE PRODU CT, except and only to theextent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications tothe Software, w ithout the writtenpermission of an officer of DSC. You may not remove any proprietary notices,marks or labels from theSoftware Product. You shall institute reasonable measures to ensure compliance wi th the terms andconditions of this EULA. Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDW ARE unit. Single INTEGRATED PRODUCT - If You acquired this SOFTWARE withHARDWARE, then theSOFTW ARE PRODUC T is li censed with the HARDW ARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDW ARE as set forth in this EULA. Rental - Youmay not r ent, l easeor lendthe SOFTWARE PRODUCT. Youmay not m ake it available to others or post it ona server or web site. Software Product Transfer - Youm ay transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDW ARE, providedYou retain no copies, You transfer all of the SOFTWARE PRODUCT (includingall component parts, the media and printedm aterials, any upgrades andthis EULA), andprovided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUC T is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUC T. Termination - W ithout prejudice to any other rights, D SC may terminatethis EULAi f You fail to comply with the terms and conditions of this EULA. In such event, Youmust destroy all copies of theSOFTW ARE PRODUC T and all of its component parts. Trademarks - This EULA does not grant You any r ights in connection wi th any trademarks or service m arks of DSC or its suppliers.

3. COPYRIGHT

All titleand intellectual property ri ghts in andto the SOFTWARE PRODUCT (includingbut not limi tedto any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printedmaterials, andany copies of the SOFTWARE PRODUCT, are ownedby DSC or its suppliers. You may not copy the printedm aterials accompanyingtheSOFTW ARE PRODUCT. All title and intellectual property rights in and to the content which m ay be accessed throughuse of the SOFTWARE PRODUCT are the property of the r espective content owner and may be protectedby applicable copyright or other intellectual property laws and treaties. This

EULA grants Youno rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers. EXPORT RESTRICTIONS - You agreethat You wil l not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions. CHOICE OF LAW - This Software LicenseAgreement is governedby the laws of theProvinceof Ontario, Canada. ARBITRATION - All disputes arising inconnection with this Agreement shall be determinedby final and binding arbitrationin accordance with the Arbitration Act, andthe parties agree to be boundby the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the languageof the arbitrationshall be English.

LIMITED WARRANTY

NO WARRANT Y - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY.

DSC DOES NOT WARRANT TH AT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILLBE UNINTERR UPTED OR ERRORFREE.

CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDW ARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS. LIMITATION OF LIABILITY; WARR ANTY REFLECTS ALLOCA TION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, D SC’S ENTIRE LIABILITY UND ER ANY PROVISION OF THIS LICENSEAGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVECANADIAN DOLLARS ( CAD$5.00). BECAUSE SOME JUR ISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLYTO YOU. DISCLAIMER OF WARRAN TIES - THIS W ARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INC LUDING ALL IMPLIED W ARRANTIES OF MERCHANTABILITYOR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES N OR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MOD8IFY OR TO C HANGE TH IS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER W ARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUC T. EXCLUSIVE REMEDY AN D LIMITATION OF WARR ANTY - UNDER N O CIRCUM STANCES SHALLDSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTW ARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. DSC recommends that the entire system becompletely testedon ar egular basis. However, despite frequent testing, anddue to, but not lim ited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail toperform as expected.

- 48 -

Page 52

Appendix 4: Limited Warranty

Digital Security Controls warrants the original purchaser that for aperiod of twelve months from thedate of purchase, the product shall befree of defects i n materials and workmanshipunder normal use. During the warr anty period, Digital Security Controls shall, at its option, repair or replaceany defectiveproduct upon return of the product to its factory, at no chargefor labour and materials. Any replacement and/or repairedparts are warranted for the r emainder of the original warranty or ninety (90) days, whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that there i s defect in material or workmanship, such written notice to be received in all events prior to expirationof the warranty period. There is absolutely no warranty on software andall software products are sold as auser licenseunder the terms of the software l icenseagreement includedw ith the product. The Customer assumes all responsibility for the proper selection, installation, operation and maintenance of any products purchasedfrom DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.

International Warranty

The warranty for international customers is the same as for any customer within Canada andthe UnitedStates, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtainservice under this warranty, pleaser eturn the i tem(s) in question to the point of purchase. All authorized distributors and dealers havea warranty program. Anyoner eturning goods to Digital Security Controls m ust first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not beenobtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanshiprelatingto normal use. It does not cover:

l damage incurred in shippingor handling; l damage causedby disaster such as fire, flood, wind, earthquake or lightning; l damage due to causes beyond thecontrol of Digital Security Controls such as excess-

ive voltage, m echanical shock or water damage;

l damage causedby unauthorized attachment, alterations, modifications or foreign

objects;

l damage causedby peripherals (unless such peripherals were supplied by Digital

Security Controls);

l defects causedby failure to provide a suitable installation environment for the products; l damage causedby useof the products for purposes other than those for whichit was

designed;

l damage from improper maintenance; l damage arising outof any other abuse, mi shandlingor improper application of the

products.

Items Not Covered by Warranty

In addition to the items which void the W arranty,thefollowing items shall not be covered by W arranty: (i) freightcost to the repair centre;(ii) products which are not identified wi th DSC' s product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performanceor prevent adequatei nspectionor testing to verify any warranty claim. Access cards or tags returned for replacement under warranty wi ll becredited or replaced at DSC's option. Products not coveredby this warranty, or otherwise out of w arranty due to age, m isuse, or damage shall be evaluated, and a r epair estimate shall be provided. No repair work will be performed until a valid purchase order is receivedfr om the Customer and a R eturn Merchandise Authorisation number (RMA) is issued by D SC's Customer Service. Digital Security Controls’s li ability for failure to repair the product under this w arranty after a reasonablenumber of attempts w ill be limi ted to a replacement of the product, as the exclusive remedy for breachof warranty. Under no ci rcumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based uponbreach of warr anty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substituteor replacementequipment, facilities or services, down tim e, purchaser’s time, the claims ofthird parties, including customers, and injury toproperty. The laws of some jurisdictions limi t or do not allow the disclaimer of consequential damages. If the laws of such a j urisdiction apply to any claim by or against DSC, the limitations and disclaimers containedhere shall be to thegreatest extent permittedby law. Some states do not allow the exclusionor l imitation of incidental or consequential damages, so that the abovem ay not apply to you.

Disclaimer of Warranties

This warranty contains the entire warr anty andshall bei n li eu of any and all other warranties, whether expressed or implied (i ncluding all implied warranties of m erchantability or fitness for a particular purpose) And of all other obligations or liabilities on the part of Digital Security Controls Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf tom odify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and li mited warranty are governed by the laws of the provinceof Ontario, Canada.

Digital Security Controls recommends that the entire system becompletely testedon ar egular basis. However, despitefrequent testing, and due to, but notlimitedto, criminal tamperingor electrical disruption, it is possiblefor this product to fail toperform as expected.

Out of Warranty Repairs

Digital Security Controls wil l atits option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyonereturning goods to Digital Security Controls must first obtainan authorization number. Digital Security Controls will not accept any shipment whatsoever for whichprior authorization has not been obtained. Products which Digital Security Controls determines to be r epairable will be repaired and returned.A set fee which Digital Security Controls has predeterminedand which may be revised from time totim e, will bechargedfor each unit repaired. Products which Digital Security Controls determines not to be r epairable will be replacedby the nearest equivalent product available at that time. The curr entmarket price of the r eplacement product wil l be chargedfor each replacement unit.

- 49 -

Page 53

WARNING: Installer please read carefully

Note to Installers

The warnings on this page contain vital information. As theonly individual incontact with system users, it is thei nstaller’s responsibility to bring each item in this warning to the attention of all users of this system.

System Failures

This system has been carefully designed to be as effective as possible.There are cir cumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail tooperateas expected for a variety of r easons. Some, but notall, of the reasons m ay be:

Access by Intruders

Intruders may enter through an unprotected access point,circumvent a sensing device,evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system.

Component Failure

Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of acomponent.

Compromise of Radio Frequency (Wireless) Devices

Signals m ay not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent r adiosignal interference.

Criminal Knowledge

This system contains security features w hich were known to be effectiveat the time of m anufacture. It is possible for persons with criminal i ntent to develop techniques which r educe the effectiveness of these features. It is important that your security system be r eviewedperiodically to ensure that i ts features remain effectiveand that it is updatedor r eplaced if it is foundthat it does not provide the protection expected.

Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expectedbattery life is a function of the deviceenvironment, usage, and type. Ambient conditions such as high humidity, highor l ow temperatures, or large temperature fluctuations m ay r educe the expected battery life. While eachtransmittingdevice has a low battery m onitor whichidentifies when the batteries needto be replaced, this monitor m ay fail to operate as expected. Regular testingand maintenance wi ll keep the system in good operating condition.

Inadequate Installation

A security system must be installedproperly inorder toprovideadequate protection.Every installationshould be evaluated by asecurity professional to ensure that all access points andareas are covered. Locks and latches on windows and doors must be secure andoperateas intended. W indows, doors, walls, ceilings and other buildingm aterials must be of sufficient strength and constructionto provide the level of protection expected. A reevaluationm ust be doneduring and after any construction activity. An evaluation by the fire and/or police department is highly r ecommended if this service i s available.

Inadequate Testing

Most problems that would preventan alarm system from operating as intended can be found by regular testingand maintenance. The complete system should be testedweekly and imm ediately after abreak-in, an attempted break-in, a fir e, a storm, an earthquake, an accident, or any kind of constructionactivity insideor outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices, andany other operational devices that are part of the system.

Insufficient Time

There may be circumstances when the system w ill operateas intended, yet the occupants will not be protectedfrom an emergency due to their inability to respond to the warnings in a timely manner. If thesystem is remotely monitored, the responsem ay not occur in time to protect the occupants or their belongings.

Motion Detectors

Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate betweenintruders and intendedoccupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection andm otioncan only be detectedin unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions,glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or sprayingof any material on the lenses, mirrors, windows or any other part of the detection system w ill impair its proper operation. Passive infraredmotiondetectors operate by sensing changes intemperature. However their effectiveness can be reduced when the ambient temperature r ises near or abovebody

temperature or if there are intentional or unintentional sources of heat in or near the detectionarea. Some of theseheat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lightingand so on.

Power Failure

Control units, intrusion detectors, smokedetectors and many other security devices require an adequate power supply for proper operation.If a device operates from batteries, it is possiblefor thebatteries to fail. Even if the batteries have not failed,they m ust be charged, in goodcondition and installed correctly. If a device operates only by AC power, any interruption, however brief, wi ll render that device inoperative while it does not havepower. Power interruptions of any length are often accompanied by voltage fluctuations which m ay damageelectronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.

Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently toprevent or minimize the harmful effects of an emergency situation.

Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of a fire for anumber of reasons, some of whichfollow. The smoke detectors may havebeen improperly i nstalled or positioned. Smoke may not be able to r eachthe sm oke detectors, such as when thefire is in a chimney, walls or roofs, or ontheother side of closed doors. Smoke detectors m ay not detect smoke from fires on another level of the r esidence or building. Every fire is different in the amount of sm oke producedand the rate of burning. Smoke detectors cannotsense all types of fires equally well. Smoke detectors m ay not provide timely warningof fires caused by carelessness or safety hazards such as sm oking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical ci rcuits, children playing with m atches, or arson. Eveni f the sm oke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escapei n tim e to avoid injury or death.

Warning Devices

Warning devices such as si rens, bells, horns, or strobes may not warn people or waken someone sleeping if there is ani nterveningwall or door. Ifwarningdevices are locatedon adifferent l evel of ther esidence or premise, then it is less likely that the occupants w ill be alertedor awakened. Audible warning devices may beinterferedwith by other noise sources such as stereos,radios, televisions, air conditioners, other appliances,or passing traffic. Audible w arningdevices, however loud, m ay not be heard by a hearing-impaired person.

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, Tyco S afetyP roducts C anada Ltddec lares thatthe radio equipmenttype Wireless AlarmS ystemw ithIntegralCellular A larmCommunicatoris in c ompliancewith Directive 2014/53/EU. Thefollowing models are cov ered by this guide: WS900-19, WS900- 29,3G7090, LT7090 (used in North America only) ,WS 901-14,WS 90124EU, WS901- 18,WS 901-28, WS911-18, WS911- 28,and 3G7090- EU. Thefull textof theE U declarations of conformityfor the modelsmentioned below are available atthe followinginternet address es: ModelWS 901-14:h ttp://dsc.com/pdf/1707001 ModelWS 901-24EU :http://dsc.com/pdf/1707002 ModelWS 901-18:h ttp://dsc.com/pdf/1707003 Model:WS901-28: http://dsc.com/pdf/1707004

Produc ts pecifications:

Frequency Bands Maximum Power

g1 433.04MHz – 434.79MHz 10mW

h1.4 868.0MHz –868.6MHz h1.5 868.7MHz –869.2MHz

2400MHz-2483.5MHz 100mW

EGSM/EDGE: 880MHz – 915MHz Class 4( 2W) @ 900 MHz, E-GSM

DCS/EDGE: 1710MHz – 1785MHz Class 1 (1W) @ 1800 MHz, D CS

FDD Band VIII:880MHz – 915MHz FDD Band I: 1920MHz – 1980MHz

European singlepointof contact Tyco S afety Pr oducts, Voltaweg 20,6101 X K E cht,Netherlands

TheWS 912-28 Con trolP anel with3G7090E -EU c ellular communicatorhas beencer tifiedby Telefication accor ding toE N501311:2006+A1:2009+A 2:2017,EN 50131-3:2009,E N50131-4: 2008,E N50131- 10:2014, EN501 31-6:2017 (Type A) andEN 50136-1:2012 (SP 2,DP2) for Grade 2, Class II.For E N50131 compliantinstallations,withalarm control panels WS 912-28 only the intrusion portion ofthe alarm sys temmay be activated.

10mW

Class E2 (0.5W) @ 900 MHz, EDGE

Class E2 (0.4W) @ 1800M Hz, EDGE

Class 3( 0.25W) @ 900/1800 MHz, FDD I/VIII

- 50 -

Page 54

The Tyco cloud collects Data from the iotega panel (public IP address, security events and statuses, security configuration, and system diagnostics) in order to improve system performance, troubleshoot customer issues, and improve user experience. You have the right to access, correct and request removal of your personal data by contacting info@tycosecurityproducts.com and the right to lodge a complaint with a supervisory authority. Tyco will not transfer this data to other parties, except for our cloud service provider in the US, with whom we have contractual Personal Data Processing Terms and EU Standard Contractual Clauses. Tyco uses industry-standard safeguards to protect your personal information. Find out more in our Privacy Statement at www.tyco.com/privacy. Your personal information will be retained as long as necessary to achieve the purpose for which it was collected and for any period thereafter as legally required or permitted by applicable law.

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco will aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco are the property of their respective owners, and are used with permission or allowed under applicable laws. Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.