Dräger X-act 7000 User Manual

Dräger X-act® 7000
D-20022-2020
2.4 inch, high contrast colour display
160° viewing angle and day/night reading mode
3-button control
For fast and easy operation
LED status indicator
Green LED glows
when test is complete
Dräger MicroTubes
For 10 measurements per gas.

Automatic drive

Multi-Gas Detector
The innovative Dräger X-act® 7000 analysis system consists of Dräger MicroTubes and an opto-electronic analysis device that lets you precisely measure gases in the low ppb range. It gives you precise results right on site, replacing slow, expensive lab analyses. It's extremely easy to use: insert the Dräger MicroTubes, start measuring, then read out the test result.
02 | Dräger X-act® 7000
Benefits
Measures the lowest-quantity concentrations with lab-quality analysis
Concentrations of hazardous substances in ambient workplace air must never exceed the defined limits. Monitoring these sometimes very low concentration levels is a responsible task. The Dräger X-act 7000 in combination with Dräger MicroTubes is focused on measuring carcinogenic and toxic substances in the low ppb range. This sensitive testing system is based on colorimetric chemical sensors capable of replacing conventional laboratory analysis and providing precise results right on site. This saves time and money.
More safety thanks to high selectivity
The substance-specific reactive layers and multiple pre-layers in the Dräger MicroTubes allow for selective gas testing. The various layers serve as a filter. During testing, they filter out other substances that occur in the workplace so that only the target substance is reflected in the test result. This significantly reduces cross­sensitivities and the number of false-positive test results.
Explosion-proof and ready to use
The RFID tags applied to the Dräger MicroTubes contain all the calibration data that apply throughout their normal lifespan of one year. This eliminates the need for lengthy function tests and manual calibration. Because it works on the basis of mass-flow measurement, air pressure fluctuations have no influence on the device. Any possible temperature or humidity influences are already accounted for during the factory calibration. The analyzer is explosion-proof and certified under ATEX and CSA. The system is also dust- and splash-resistant in accordance with IP54. It also meets the requirements for electromagnetic compatibility under EN 61326-1.
Easy to use
After an automatic self-test, the X-act 7000 analysis system is immediately ready for use. It is suitable for testing with all available Dräger MicroTubes. Simply insert the right Dräger MicroTube for your testing needs. The automatic drive carefully draws the MicroTube in and positions it. Control your test using the 3-button control and 2.4 inch colour display. When the test is complete, the green LED will glow and a message is displayed on the screen. You can store the test result, location and time in the internal data logger and read it later using the Dräger CC Vision software. The device is powered by five easily replaceable AA alkaline batteries. The battery life lasts for more than ten hours of testing and can be read on the display.
Also suitable for remote sampling
Using the coupler (connector piece), the Dräger X-am® Pump can be attached to the X-act 7000. This allows you to test for carcinogenic and toxic substances in the ppb range, even in hard-to-reach places like ducts, pipelines or tanks up to a distance of 45 meters (147.6 feet). Because the X-am Pump is also certified explosion-proof for Zone 0, it is perfectly suited for these tasks.
System Components
D-3380-2019
Dräger X-act® 7000 | 03
Dräger MicroTubes
With each set of MicroTubes, you can perform 10 tests. The concentrations of hazardous substances are shown on the X-act® 7000 display. Specific MicroTubes even allow you to perform tests in the ppb range. The RFID tag applied to the Dräger MicroTube set contains all the calibration data that apply throughout their normal lifespan of one year. This eliminates the need for lengthy function tests and manual calibration.
Accessories
D-11862-2016
Dräger X-am® Pump for Dräger X-act® 7000
The Dräger X-am® Pump is an external pump for portable gas detection devices. In combination with the X-act® 7000, it allows you to perform remote testing (for example, inside tanks or ducts). To use it, simply attach the pump to the Dräger X-act® 7000 using a coupler. Control the pump using the X-act® 7000 software.
Coupler
The coupler is the connector between the Dräger X-act® 7000 analysis system and the Dräger X-am® Pump. It creates a secure, sealed connection between the two devices.
D-3379-2019
04 | Dräger X-act® 7000
Accessories
D-50851-2015
FKM hose
Solvent-resistant
Available in four lengths: Inner diameter 3.2 mm, length 5 m (16.4 ft) Inner diameter 3.2 mm, length 10 m (32.8 ft) Inner diameter 3.2 mm, length 20 m (65.6 ft) Inner diameter 3.2 mm, length 45 m (147.6 ft)
PVC hose
D-50855-2015
D-25396-2009
With PTFE inner-hose
Available in two lengths: 3 m (9.8 ft) 15 m (49.2 m)
Telescopic probe
Available in four lengths: 70 cm (27.6 in) 90 cm (35.4 in) 100 cm (39.4 in) 150 cm (59 in)
Pre-tube holder
Pre-tube holders are needed to improve the sensitivity and selectivity of some Dräger MicroTubes even further. The pre-tube holder ensures a secure, sealed connection with the Dräger X-act® 7000.
D-6549-2017
Services
D-2331-2016
Dräger X-act® 7000 | 05
Product Service
Our product service provides support with different service packages – in our workshops or directly on your premises. Care, maintenance and servicing are crucial for safety and reliability – but careful maintenance and care are a must, even when it comes to commercial considerations. Preventive checks, ongoing care and use of original replacement parts improve the longevity of your investment.
Training
D-2335-2016
D-2330-2016
The Dräger Academy has shared its solid, practical knowledge for over 40 years. We hold more than 2,400 training courses each year, on a range of over 600 topics, with more than 110 authorized trainers. We equip your staff with practical knowledge and ensure that what they learn can be applied effectively, both day-to-day and, more importantly, whenever critical situations occur. We will be pleased to develop a customised training program for you.
Rental Service
From bridging a temporary shortage of equipment to procuring special equipment for applications involving specific requirements: If you only need to cover a temporary higher demand, then Dräger Rental Service with over 65,000 pieces of rental equipment is an economical alternative to purchasing. Fast, straightforward and with a wide range of additional services available upon request.
Shutdown Safety Service
You need a comprehensive safety technology solution which equips you optimally for your project. You have to comply with many different legal requirements – even under intense time pressure. A potential conflict could arise between maximum efficiency and the highest possible degree of safety. We help you to establish a balance: Our Shutdown Safety Service is a solution which takes into account all of the requirements for a shutdown, and your individual needs in particular.
D-2329-2016
06 | Dräger X-act® 7000
Technical Data
Measuring range and resolution Varies, depending on the Dräger MicroTubes in use
Typical testing time From 5 seconds to 1,200 seconds, depending on the Dräger
Ready to use Immediately
Calibration Not necessary
Operating temperature 0 to +50 °C (+32 to +122 °F)
Air pressure 700 to 1,300 hPa
Humidity 0 to 95 % relative humidity, non-condensing
Recording of measured data CMOS sensor optics and LED light
System diagnostics Automatic, using micro-controllers for all system components
Display 2.4 inch high contrast, color display with a resolution of
Menu languages 30
Operating time Approx. 600 minutes of testing time
Power supply 5 x 1.5 v AA alkaline batteries
Dimensions (L x W x H) 195 mm x 85 mm x 70 mm (7.7 in x 3.3 in x 2.8 in)
Approvals ATEX/IECEx II 1G Ex IIC T4 Ga
Protection class IP54, dust- and splash-resistant
MicroTubes in use and the concentration of the test substance.
-20 to +55 °C (-4 to +131 °F) (Analyzer)Storage temperature
+4 to +25 °C (+39 to +77 °F) (Dräger MicroTubes)
240 x 320, viewing angle of 160°
cCSAus Class I, Zone 0, AEx ia IIC T4 Ga
Dräger MicroTubes
Description Test range Test time (min-max) Part number
Ammonia 1 – 100 ppm 10 - 75 seconds 86 10 130
Ammonia 100 – 2,500 ppm 3 - 45 seconds 86 10 020
Benzene 1 – 150 ppb 100 – 900 seconds 86 10 600
Benzene 0.15 – 10 ppm 25 – 150 seconds 86 10 030
1,3-Butadiene 25 – 500 ppb 200 – 600 seconds 86 10 460
1,3-Butadiene 0.5 – 25 ppm 10 – 280 seconds 86 10 300
Carbon Dioxide 200 – 50,000 ppm 2 – 120 seconds 86 10 190
Carbon Monoxide 10 – 1,000 ppm 5 – 300 seconds 86 10 080
Chlorine 50 – 5,000 ppb 10 – 400 seconds 86 10 010
Demo NA 5 – 30 seconds 86 10 290
Ethylene Oxide 25 – 250 ppb 150 – 600 seconds 86 10 200
Ethylene Oxide 0.25 – 10 ppm 100 – 500 seconds 86 10 580
Formaldehyde 5 – 150 ppb 360 – 960 seconds 86 10 540
Formaldehyde 0.15 – 3 ppm 300 – 600 seconds 86 10 100
Hydrochloric Acid 0.5 – 25 ppm 10 – 100 seconds 86 10 090
Hydrocyanic Acid 0.5 – 50 ppm 20 – 180 seconds 86 10 520
Hydrogen Sulfide 0.1 – 50 ppm 5 – 960 seconds 86 10 050
Mercury
Nitrogen Dioxide 0.25 – 50 ppm 10 – 210 seconds 86 10 120
Nitrous Fumes 0.25 – 50 ppm 5 – 120 seconds 86 10 060
Petroleum Hydrocarbons 10 – 3,000 ppm 10 – 360 seconds 86 10 270
Sulphur Dioxide 0.05 – 5 ppm 20 – 480 seconds 86 10 110
Toluene 10 – 1,000 ppm 6 – 360 seconds 86 10 250
Xylene 10 – 1,000 ppm 10 – 240 seconds 86 10 260
0.005 – 0.25 mg/m
3
240 – 1,200 seconds 86 10 350
Ordering Information
Dräger X-act® 7000 | 07
Dräger X-act® 7000
consisting of: Basic device X-act® 7000 incl. batteries, shoulder
strap complete, MicroTube Demo, Torx T10 screwdrawer, USB
cable 2 m with Mini-connection
Pump accessories
Dräger X-act® 7000 Coupler
Dräger X-am® Pump
Other accessories
Dräger X-act® 7000 Pre-tube holder
Dräger Tubes®, ppb-Booster Basic
Tube opener, TO 7000 64 01 200
Shoulder strap, compl. 83 26 823
Label holder for shoulder strap 83 26 824
“Silver” Sticker Set, 5 pieces 83 27 645
“Blue” Sticker Set, 5 pieces 83 27 646
“Red” Sticker Set, 5 pieces 83 27 647
“Green” Sticker Set, 5 pieces 83 27 648
“Yellow” Sticker Set, 5 pieces 83 27 649
Carry case, 470 x 365 x 190 mm, black 37 03 690
Display protector film (3 pcs.) 83 26 828
Dust and water filter for pump inlet 83 19 364
Probes
ES150 Telescopic probe (max. length: 150 cm / 59 in) 83 16 533
Telescopic probe 100, incl. adapter
(max. length: 100 cm / 39.4 in)
Telescopic probe 90 (max. length: 90 cm / 35.4 in) 83 16 532
Telescopic leak probe 70 (max. length: 70 cm / 27.6 in) 83 16 531
86 10 800
86 10 810
83 27 100
37 01 985
37 02 013
83 16 530
Hoses
PTFE-lined PVC hose, 3 m (9.8 ft) 83 26 980
PTFE-lined PVC hose, 15 m (49.2 ft) 45 94 679
Replacement hose for probes, 2 m (6.6 ft) 83 18 205
FKM hose, inner diameter: 3.2 mm, length: 5 m (16.4 ft) 83 25 705
FKM hose, inner diameter: 3.2 mm, length: 10 m (32.8 ft) 83 25 706
FKM hose, inner diameter: 3.2 mm, length: 20 m (65.6 ft) 83 25 707
FKM hose, inner diameter: 3.2 mm, length: 45 m (147.6 ft) 83 28 212
Hose connector, outer diameter: 5 mm (10 pcs.) 83 20 087
Adapter
Hose adapter, incl. 40 mm (1.6 in)
30 mm / 1.2 in FKM (10 pcs.)
Reducer piece, incl. 30 mm (1.2 in)
FKM (10 pcs.)
Luer Adapter, male, 3 mm 83 27 641
83 19 231
83 20 086
08 | Dräger X-act® 7000
Notes
Not all products, features, or services are for sale in all countries. Mentioned Trademarks are only registered in certain countries and not necessarily in the country in which this material is released. Go to www.draeger.com/trademarks to find the current status.
CORPORATE HEADQUARTERS
Drägerwerk AG & Co. KGaA Moislinger Allee 53–55 23558 Lübeck, Germany www.draeger.com
Locate your Regional Sales Representative at: www.draeger.com/contact
USA
Draeger, Inc. 7256 S. Sam Houston Parkway W., Suite 100 Houston, TX 77085 1 800 4DRAGER (1 800 437 2437)
.
CANADA
Draeger Safety Canada, Ltd. 2425 Skymark Ave., Unit 1 Mississauga, Ontario L4W 4Y6 1 877 DRAGER1 (1 877 372 4371)
.
91 05 330 | 21.03-7 | HQ | PP | Subject to modifications | © 2021 Drägerwerk AG & Co. KGaA
Loading...