SBI INC., one of the most important wood stove and fireplace manufacturers in Canada,
congratulates you on your purchase and wishes to help you get maximum satisfaction
from your wood stove. In the pages that follow, we will give you advice on wood heating
and controlled combustion as well as technical specifications regarding installation,
operation and maintenance of the model you have chosen.
The instructions pertaining to the installation of your wood stove comply with ULC-S627
and UL-1482 standards.
Read this entire manual before you install and use your new stove. If this stove is
not properly installed, a house fire may result. To reduce the risk of fire, follow the
installation instructions. Failure to follow instructions may result in property
damage, bodily injury, or even death.
Consult your municipal building department or fire officials about restrictions and
installations requirements in your area and the need to obtain a permit.
Keep this instructions manual for future references.
CAUTIONS:
• HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY
CAUSE SKIN BURNS.
• DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE.
• DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED.
• DO NOT BURN WASTES, FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR MOTOR OIL.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
• ALWAYS CLOSE THE DOOR AFTER THE IGNITION.
2
TECHNICAL SPECIFICATIONS
Combustion Type:
Recommended Surface
Heating Capacity : E.P.A :
Real :
Efficiency :
Average Emission:
Colors :
Flue Pipe Diameter :
Chimney type :
Minimum Chimney Height :
Maximum Log Length :
Dimensions
Blower 75 CFM (2,83 m3/min) with
variable speed control
15 ½’’ x 8 ½’’
(394 x 216 mm)
(432 x 267 mm)
263 lbs ( 119 Kg) 380 lbs (172 Kg) 510 lbs (231 Kg)
YesYes
17 x 10 ½’’
Yes
20 ½ x 8 ¾’’
(521 x 222 mm)
Thermodisc 100-120oF (37-490C). YesYesYes
3
ASSEMBLY
PEDESTAL AND DECORATIVE SIDEWALL INSTALLATION
Pedestal Installation :
1. Remove all bricks and insulations in
the appliance.
2. Slowly, lay down the stove on his
back.
3. Install legs or the pedestal with the
supplied nuts and bolts. Stand up
the stove and place it with the
required clearances. Note that
there is eight holes in the bottom of
the stove but only four will align with
the pedestal.
4. Slide the front part of the pedestal
base around the pedestal and fix
the rear part with the two supplied
screws.
5. Slide the ash pan in position (for
Figure 1: SIBERIAN-1200 and 1600
Deluxe model only).
Side Panels Installation :
1. Fix the front part of the decorative
side with two screws supplied. The
oblong holes allow to adjust the
height of the side 3\16" (5 mm)
above the top of the stove.
2. Then, fix the back on the decorative
side with three screws and washers
supplied. Line up the decorative
side in relation to the side of the
appliance.
Figure 2: SIBERIAN-2000
4
BRICKS INSTALLATION (SIBERIAN-1200)
• Refractory bricks are to be installed
according to figure 4.
• In both stoves, the baffle brick must be
pushed as close to the front as possible
onto its metallic support.
• The upper bricks (2) must lay on the
vertical bricks (4) grove
• Note that a plain brick is supplied
instead of a ashtray cap on standard
models.
Figure 3: SIBERIAN-1200
5
BRICKS AND INSULATION INSTALLATION (SIBERIAN-1600)
1. Remove from the stove all bricks and insulation.
2. Install all side bricks (12 x 4 1/2" x 9")
3. Install the back bricks (6 x 4 1/2" x 9")
4. Install the bottom bricks (4 x 4 1/2" x 9") + (2 x 6" x 7").
5. Install the "T" shape support and the bricks (4 x 4 1/2" x 9") + (2 x 3" x 9").
6. Install the baffle bricks (4 x 4 1/2" x 9") + (2 x 3" x 9") on T shape support.
7. Finally gently slide the insulation panels over the baffle bricks.
The stove is normally supplied with secondary air tubes in position. To install the baffle bricks
and white ceramic insulation, it’s necessary to remove the two front secondary air tubes. First
place only one baffle brick and one white ceramic insulation. Use the same method to put the
other baffle brick and insulation. Put back in place the secondary air tubes.
Install the yellow insulation and the 6" x 8" or 6" x 6" bricks. Install the side and bottom bricks.
Figure 5: Siberian 2000Refractory Bricks Assembly
7
AIR TUBES INSTALLATION (SIBERIAN 2000):
The secondary air tubes are painted different colours . The back tube is yellow, the middle
one is red and the front is unpainted. Before installing, make sure the locating holes in the
tubes (holes near one end of the tube) are on the left side. Insert one tube in the right side
air channel and slide it to the right as much as possible. Bring the left end of the tube
aligned with the ring welded to the left air channel. Move the tube to the left until the
locating holes are aligned with those in the ring. Insert a cutter pin to hold in place. The air
injection holes should be facing down in the front and middle tubes.
Figure 6: Air Tubes Installation
8
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.