Drive Medical Design AS 5000 User Manual

Low air loss/Alternating pressure mattress

Instruction Manual

Drive Medical Design & Manufacturing

99 Seaview Boulevard

Port Washington, NY 11050

Toll Free: 877-224-0946

Local: 516-998-4600

www.drivemedical.com

REV2.12.17.13

746002-5150 V1.0

PLEASE READ ALL INSTRUCTIONS BEFORE USE.

CONTENTS

IMPORTANT SAFEGUARDS...................................................... 2

1. INTRODUCTION .................................................................... 3

2. PRODUCT DESCRIPTION ..................................................... 4

3. INSTALLATION ....................................................................... 5

4. OPERATIONS ......................................................................... 7

5. CLEANING.............................................................................. 8

6. MATTRESS STORAGE .......................................................... 9

7. MAINTENANCE ...................................................................... 9

8. TECHNICAL DESCRIPTION ................................................ 10

APPENDIX A: EMC INFORMATION ......................................... 12

a/ The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6,765 MHz to 6,795 MHz;13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz.

b/ The compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency ran MHz to 2.5 GHz are intended to decrease the likelihood that mobile/portable communications equipment could cause interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 is used in calculating the recommended separation distance for transmitters in these frequency ranges.

c/ Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be ob served to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the device.

d/ Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

e 80

Recommended separation distances between portable and mobile RF communications equipment and this device:

This device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of this device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and this device as recommended b elow, according to the maximum output power of the communications equipment

Rated maximum

output power of transmitter

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73 1 1.2 1.2 2.3 10 3.8 3.8 7.3 100 12 12 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in

meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in a ll situa ti ons. Ele ctroma gneti c pr opa

reflection from structures, objects, and people.

Separation distance according to frequency of t ransmitter m

150 kHz to 80 MHz

Pd 2.1

80 MHz to 800 MHz

Pd 2.1

800 MHz to 2,5 GHz

ation is affected by absorption and

Pd 3.2

Guidance and Manufacturer’s Declaration - Electromagnetic Immunity:

This device is intended for use in the electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.

Immunity Test IEC60601 test level Compliance Electromagnetic Environment-Guidance

3 Vrms

3 V/m

Portable and mobile RF communications equipment should be used no closer to any part of this device, including cables, than there commended separation distance calculated from the equation applicable to the frequency of t he transmitter.

Recommended separation distance

150kHz to 80MHz

Pd 2.1

150kHz to 80MHz

Pd 2.1

80 MHz to 2.5G MHz

Pd 3.2

Where P is the maximum output power rating of the transmitter in watts (W) accordin

to the transmitter manufacturer and d is the recommended separation distance in meters (m).

Field stren as determined by an electromagnetic site survey compliance level in each frequency range

Interference may occur in the vicinity of equipment marked with the following symbol:

ths from fixed RF transmitters,

, should be less than the

Conducted RF IEC 61000-4-6

Radiated RF IEC 61000-4-3

NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption

and reflection from structures, objects and people.

3Vrms150 kHz to 80 MHz outside ISM

bands

m 80 MHz to 2.5

3 V GHz

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE

DANGER - To reduce the risk of electrical shock:

1. Always unplug this product immediately after using.

2. Do not use while bathing.

3. Do not place or store product where it can fall or be pulled into a tub or sink.

4. Do not place in or drop into water or other liquids.

5. Do not reach for a product that has fallen into water. Unplug immediately.

WARNING - To reduce the risk of burns, electrical shock, fire, or injury:

1. This product should never be left unattended when plugged in.

2. Close supervision is necessary when this product is used by, on, or near children or invalids.

3. Use this product only for its intended use as described in this manual.

4. Do not use attachments not recommended by the manufacturer.

5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or exposed to water. Return the product to a service center for examination and repair.

6. Keep the cord away from heated surfaces.

7. Never block the air openings of this product. Never place the product on a soft surface, such as a bed or couch, where the air openings may become blocked. Keep the air openings free of lint, hair, and other similar particles.

8. Never drop or insert any object into any opening or hose on this product.

9. Connect this product to a properly grounded outlet only. See Grounding Instructions.

NOTEs, CAUTIONs AND WARNINGs:

- Calls attention to useful information, tips, reminders.

NOTE CAUTION

- Calls attention to correct operating or maintenance procedures in order to prevent damage to or destruction of the equipment or other property.

WARNING

- Calls attention to a potential danger that requires correct operating procedures or practices in order to prevent personal injury.

SYMBOL Definitions

Authorized representative in the European community.

Manufacturer

Complies with standards protecting against electric shock for type BF equipment. Attention, you should read the accompanying information carefully!

Attention – Observe proper Disposal of Electrical & Electronic Equipment (WEEE): This product should be handed over to an appropriate collection point for the recycling of electrical and electronic equipment. For more detailed information about the recycling of this product, please contact your local city office, household waste disposal service or the retail store where you purchased this product.

Consult operating instructions

Class II

Functional earth.

+ 5 hidden pages