Drive Bellavita User Manual

Badelift

Quick User guide - First installation

1. Remove from the carton and check stop lever

1

1. Raise the drive unit

2

2. Move the backrest forward

3

3. Raise the seat unit

4

4. Please ensure that the red seat
unit locking mechanism is engaged
by pushing down on the seat.

2. Attaching the backrest into the seat unit

1a

correct

1b

wrong wrong

2

B

A

3

4 5

correct

1. Important:
Please ensure that the actuator is fully

retracted in the backrest.

2. A: Bearing block – B: Guide pin
Slide the backrest into the hinge located

on the back of the seat unit.

3. Lift the backrest to an 45° Angle until
it clicks into the latch.

3. Charging the battery • Attaching the hand control

1

1

2

Recharge the battery after application.

1. Place the chinch 1) of the charger
into the socket of the cable 2) attached
to the hand control. During the charging
process, the red light will be on. The
light changes to green when the battery
is fully charged. After Full charged the
battery, please disconnect the charger
from the hand control.

Recommended value: Storage the hand
control on a 15-20 grad celsius place.

Don´t place the hand control at a heater.
Please avoid direct sunlight.

2

2

5

3

4

1

4. Placing or removing the bathlift into/from the bathtub

1

2

4. Important:
Please ensure that the actuator end is/

sits properly in the base plate´s ramp.

3

2. Hand control
description:

3. Plug the hand control to the bathlift (at the back of the

1. Green: power On button

2. Red: emergency Stop

3. Blue: down button

4. Yellow: up button

5. Control light

3 4

backrest). Make sure that the sable is properly seated on the
jack. The red ring at the jack is now hidden.

1.

• Remove anti-slip mats or similar utilities.

• The tongues of the rear suction caps must

be directed outwards.

• The suction cups at the bottom of the Bel­lavita must be clean and dry.

• Make sure that the rear suction cups are lo­cated close to the bevelled edge of the bath.

2.

• Attention! It is very important that both
guide pins are inserted into the bearing
blocks! (see point 2).

• Pivot the attached backrest up until it reach­es its final position.

• The backrest must not collide with the
bathtub. In that case you have to reposi­tion the bathlift.

3.

• Before usage, bring the lift into a position
wich allows seating comfortably.

4.

• In need of elimination please turn 45° In
advance and pull out. Remove backrest ac­cording point 2.

• Remove the two rear suction cups by pull­ing the tongues. The seat unit can now be
removed from the bathtub.

5. Side flap protectors (pair) - Installation and Usage

1

The bathlift side protectors should be used on
baths fitted with grab handles or similars which
protrude inside the bath.

To install the
over the
to slide down the edge of

protectors,

grab

handle and allow the long

snap the hooked end

the

end

bath.

Drive Medical GmbH & Co. KG • Leutkircher Straße 44 • D-88316 Isny/Allgäu • Germany • [e-mail] • www.drivemobil.de • Tel.: [phone] • Fax: [phone]

Once installed, the side
will slide against the
edge of the bath. This
bathlift side flaps getting caught underneath the
grab handles.

For longer bath handles, one or more protectors
may be installed (as shown on picture).

flaps

protector

removes

on the bathlift

rather than

the risk of the

the

The product code is 400 570 and protectors are
supplied in pairs.

As per: 06 / 2014 - Subject to error and change