Drive ASB-2109, ASB-2109V Installation And Use Instructions And Warnings

Installation and Use Instructions

ASB-2109 & ASB-2109V

Chair Belts

Non-Restraint Chair Belts for use with Smart Caregiver Fall/Mobility Monitors

TL-2109_TL-2109V 1-14

ASB-2109 & ASB-2709V Chair Belts

WARNIN G: Failure to comply with warning may result in injury or death. This device is not suitable for all individuals. Other devices may be required.

This device is not a substitute for visual monitoring by caregiver. The manufacturer does not claim that this device will stop elopement and/or stop falls. This device is designed to augment caregivers’ comprehensive resident mobility management program. THIS DEVI CE IS NOT D ESIGNED

TO REST RAIN OR HO LD INDIVIDUA LS IN POSI TION IN THE IR CHAIRS. Test this device before each use. Read the instructions and Legal Disclaimer.

The Drive ASB-2109 and ASB-2109V Chair Belts are designed to be installed by the end user. As such, it is the entire responsibility of the buyer to insure that the system is properly installed and tested. Further, the system is not designed to replace good caregiving practices including, but not limited to:

A.) Direct patient supervision

Seat Belts

SEAT BELT PLACEMENT

• Unscrew one screw on either side of wheelchair that holds the seat in place.

• Attach the seat belt to wheelchair by lining up the grommet holes on seat

belt with the screw holes. Re-insert screws through both seat belt and wheelchair to hold seat belt in place. Make sure the screws are tightened.

• Adjust the seat belt to the desired length using the black buckle that holds the adjustment strap in place.

• Connect the seat belt cord to the monitor.

• Place the monitor out of reach of the resident. Suitable mounting

locations include the back of wheelchair, or on the chair handle so that the resident cannot tamper with the monitor.

TEST THE SYSTEM

• now active. The alert will sound whenever the seat belt is unbuckled.

• When the alert is activated, press the “Reset” button on front of the monitor to silence the alert or use the Caregiver Key, depending on your reset setting. The status light on front of monitor will blink when the seat belt is plugged into the monitor and buckled.

C.) Testing of the system before each use

WHERE PERMISSIBLE, IT IS THE SELLER’S INTENT TO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO REFUND OF THE PURCHASE PRICE OR REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY LIABILITY FOR COMPENSATORY OR OTHER DAMAGES ARISING OUT OF THE USE OF THE GOODS.

WARNING: The manufacturer does not claim that this device will stop elopement and/or stop falls. This device is designed to augment caregivers’ comprehensive resident mobility management program. This product is to be used by a licensed caregiver only.

Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for a period of one year from the date of sale. Other than this limited warranty, seller makes no express or implied warranties. Except for this limited warranty, NO EXPRESS OR IMPLIED WARRANTIES ARE GIVEN AND NO AF FIRMATION OF SELLER, BY WORDS OR ACTION, WILL CONSTITU TE A WARRANTY. THE GOODS BEING PURCHASED ARE BEING SOLD ON A “WITH ALL FAULTS” BASIS. THE ENTIRE RISK AS TO THE QUALITY AND PE BUYER. SHOULD THE GOODS PROVE D EFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER, AND NOT THE MANUFACTURER, DISTRIBUTOR OR RETAILER, ASSUMES THE ENTIRE COST OF ALL N ECESSARY INSTALLATION, SERVICING OR REPAIRS.

Drive Medical Design & Manufacturing

99 Seaview Boulevard, Port Washington, NY 11050 www.drivemedical.com

RFORMANCE OF THE GOODS IS WITH THE

Need S

et-up Help? (866) 621-4933

Quick Start Instructions

y Auy Au

o o

et™et™

adad

ostost

LLooww

ttttee

MoniMonittor Stor Staatustus

titivveeWWhen Blinhen Blin

inging

ad and Moniad and Moni

oror

y Auy Au

o o

et™et™

adad

ostost

LLooww

ttttee

MoniMonittor Stor Staatustus

titivveeWWhen Blinhen Blin

inging

ad and Moniad and Moni

oror

Install

Batteries

The battery compartment door is secured with the included Phillips-head screw

Tone

Adjustment

Alert Volume Adjustment

Alert Delay

Adjustment

Close battery door and secure it with small Philips-head

screw. Place monitor back into its

plastic protective boot.

For more informati on about t he Caregiver Key™, and h ow it can be used in your facilit y’s Fall Asses sment Progra m call 866-621-493 3

Tone

activated and operating properly.

beeps, indicating that the system is working. The Monitor

Status LED will blink every 3 seconds when the system is

Delay

Volume

Dcrease/Increase

2sec 1sec 0sec3 2 1

user. The manufacturer does not claim that this device will

Warning: Failure to comply with warning may result in injury

or death. This device is not suitable for all individuals. Other

stop elopement and/or stop falls. This device is designed to

devices may be required. This device is not a substitute for

agument caregivers comprehensive resident mobility

visual monitoring by caregiver. Sensor pad fall monitors are

management program. Test this device before each use.

Read the instructions and legal disclaimer.

Read Instructions Before Use:

Battery not included. Use 3 x AA alkaline Batteries.

Set Up: Plug sensor pad into the fall monitor. Apply pressure to

the sensor pad to test the system. The monitor will emit two

Need Set-up Help? (866) 621-4933

Seat Belt Installation

Unscrew one screw on either side of the wheelchair that holds the seat in place.

Attach seat belt to the chair by lining up the grommet holes with the screw holes. Re-insert screws through both the seat belt and the chair securing the seat belt in place.

Adjust the seat belt to the desired length by routing the strap through the buckle as shown in Figs A-C.

Route the strap through

the buckle as shown

Strap routed correctly

before tightening

Pull the end of the

strap to tighten

ASB-2109 & ASB-2109V

Mount the Fall Monitor

Mount the monitor out of reach of the resident. Suitable mounting location is the back of wheelchair, so that the resident cannot tamper with monitor or reach the “Reset” button.

Connect the Seat Belt to

the Fall Monitor

Pinch the cord together and route it through the strain relief recess.

Bottom of monitor

Plug the cord

into the monitor.

Test the System

Seat Belt Closed Seat Belt Opened

now active. The monitor will sound the alert whenever the Seat Belt is unfastened.

When the monitor is activated press the “Reset” button. This will shut down the alerting mode.

D ri ve M ed ic a l De si g n & M a nu fa c tu ri n g

Resetting the Monitor/ Tamper Proof™ Mode with Caregiver Key™ (Optional)

Caregivers can choose to reset the CordLess® Monitor in either of two ways:

“Reset Switch ON”: Pressing the Reset button on the front of the monitor.

“Reset Switch OFF”: Placing the optional Caregiver Key over the red dot on the front of the monitor.

Option 2 allows only the caregiver to reset the monitor.

See switch on side of the monitor to select the monitor of your choice.

For more information about the Caregiver Key™ and how it can be used in your facility’s Fall Risk Assessment Program call 866-621-4933

el: 866-371-2266T | www.drivemedical.com

Refer to User Instructions

before changing this setting.

Safety Auto Reset™

Reset Button-

Use Caregiver Key

Reset Button OFF

To Turn OFF

6V DC

300mA MAX

Low

Battery

“Reset Button ON” Mode

Press the Reset button to reset the monitor.

Pad and Monitor

Reset

Monitor Status

Active When Blinking

Pad Lost

“Reset Button OFF, Use Caregiver Key™ To Turn OFF” Mode. Place the Caregiver Key™ over the red dot to reset the monitor.