DreamLine DL-6995-04CL, SHBW-1360603-01 User Manual

QWALL TUB

TUB ACRYLIC BACK WALL INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine
without prior notice. For the latest up-to-date technical drawings, manuals or any

TM

reserves the right to alter, modify or redesign products at any time

other details please refer to the support.BathAuthority.com

web page.

Please carefully read the instructions before installing. If you have any questions
regarding installation, please call our technical support specialists Monday through
Friday 9:00 AM – 5:00 PM EST at 1-866-731-8378, ext. 3 or e-mail our technical support
group at

For more information on DreamLineTM Tub Back Wall please visit www.BathAuthority.com

Rev 1.1

[e-mail].

1

Preparation

1. After opening all boxes and packages, read this introduction carefully. Check that all of

the needed parts are included in the package, by marking all the components on the
“Detailed Diagram of Tub Back Wall Components”. Examine boxes and packages for
shipping damage. If the unit has been damaged, has a finishing defect, or has missing
parts, please contact our customer support department within 3 business days of the
delivery date. Please note that DreamLine TM will not replace any damaged products or

missing parts free of charge after 3 business days or if the product has been
installed. Feel free to contact DreamLineTM if you have any questions.

2. Please note that you should consult your local building codes with questions on

installation compliance standards. Building and plumbing codes may vary by
location, and DreamLine is not responsible for code compliance standards for your
project.

3. This acrylic wall system is specially designed to be installed over any solid surface. If you

are installing the acrylic walls over the existing tiles, remove all loose tiles before the
installation. If you are installing over the existing painted walls, take all loose paint off.
Please, note that some cutting and drilling might be necessary during the installation
process.

4. Make sure to turn off the water supply, remove faucet, handles or any fixture trims

protruding from the wall. Clean the surface removing soap film and dirt from all wall
surfaces using regular household detergent, then wipe it dry.

Caulk

Level

Tools Required

Tape
Measure Pencil

Caulk
Gun

Electric
Drill

Knife

Drill bit

(Ø 5/16")

Hammer

T-Square

Phillips
Screwdriver

Rev 1.1

2

Detailed Diagram of Tub Back Wall Components

4

6

7

8
9

10

3

1

2

5

Packing List

01 Side panel 2pcs 06 Wall anchor 21pcs

02 Back panel 2pcs 07 Countersunk screw ST4.2×30 21pcs

03 Decorative edge molding 2pcs 08 Decorative cover 15pcs

04 Corner cover 2pcs 09 Glass shelf 2pcs

05 Wall cover 1pc 10 Shelf bracket 6pcs

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the
detailed diagram and packing list in your manual as a reference. Before discarding the carton,
check for small hardware bags that tend to fall to the bottom of the box. If any parts are
damaged or missing, please contact DreamLineTM for replacement.

Rev 1.1

3

Back Panel Installation Instruction

1. Measure the distance of the back wall

of the tub (corner to corner)
The distance is “W”

See Fig. 1 for details.

W

2. Divide the W measurement by 2

(W/2). Place a mark on the back wall

and draw a vertical line from top to
bottom.

See Fig. 2 for details.

Fig. 1

W/2

W/2

Rev 1.1

Fig. 2

4

3. Measure the side walls from the

corner to the front point where the
Side panel (01) is going to end.
This distance is “D”.

See Fig. 3 for details.

D

D

4. Verify on which side of your tub

wall the fixtures will be installed.
Place a mark on the side wall (NB:
not the side panel!) with a
distance of 1” (one inch) from the
corner and draw a vertical line from
top to bottom.
Take the exact measurements:

• from the fixture to the line:

(A, B, C)

• from the fixture to the bottom:

(E, F).

See Fig. 4 and Fig. 5 for details.

E

”

F

A

Fig. 3

D - 1”

C B

D

Trim line

Rev 1.1

Fig. 4

5

Attach the Center cover (05)

5.

vertically at the center point

Fig. 5

3

along the line and mark the
drilling holes through the

Ø5/16”

predrilled holes on the Center
cover.

Drill the holes using Ø5/16” drill
bit and insert the Wall Anchors
(06).

See Fig. 6 and Fig. 7 for details.

2

4

Rev 1.1

Fig. 6

6

6. Attach the Corner cover (04)

to the corner of the wall and
mark the drilling holes
through the predrilled holes
on the Corner cover.
Drill the holes using Ø5/16”
drill bit and insert the Wall
Anchors (06).

See Fig. 8 and Fig. 9 for
details

1

2

Fig. 7

3

Ø5/16”

4

Rev 1.1

Fig. 8

7

7. Determine the position of both Back

panels (02).

NOTE:

a) Narrow side of the Back panel

cannot be trimmed and should
face the center of the Back wall.

b) Wide side of the Back panel can

be trimmed to the size of the wall
and should face the corner.

Place a mark on the wide side of the

Back panel with a distance of
(W/2 – 1”) from the center edge of

the Back panel to the wide side of
the Back panel and draw a straight
line from top to bottom.

See Fig. 10 for details.

Fig. 9

W/2-1”

W/2-1”

a

b

b

Rev 1.1

Fig. 10

8

8. Place the Back panel (02) on a flat piece of

plywood or a particle board. Cut the side end of the
Back panel by making a few deep scratches with a
sharp industrial knife using a T-Square tool or a
handheld jig saw.

See Fig. 11 and Fig. 12 for details.

1

2

W/2-1”

Fig. 11

W/2-1”

a

Rev 1.1

Fig. 12

9

9. Mount the Center cover (05) to the center of the

back wall using the Countersunk screws

ST4.2×30 (07). Do not tighten the screws. Leave

the Center cover loose on the wall.

See Fig. 13 for details.

1

2

10. Apply the sealant to the back of the

left Back panel (02).

See Fig. 14 for details.

Fig. 13

Rev 1.1

Fig. 14

10

11. Slide the right edge of the left Back panel (02) all the way

behind the Center cover (05) and push the Back panel
against the wall.
You can adjust the position of the Back panel before the
sealant sets.
Apply equal pressure to the whole surface of the Back panel
from top to bottom.
Fasten the Corner cover (04) to the left corner of the back

wall using the Countersunk screws ST4.2×30 (07). Do not

tighten the screws.

See Fig. 15 for details.

1

2

3

12. Repeat Step 10 and Step 11 to install the right Back panel

(02) to the right side of the back wall.

See Fig. 16 for details.

Fig. 15

4

5

6

Rev 1.1

Fig. 16

11

13. Align both Back panels at the top and tighten

the screws on the Center cover (05) to secure
this assembly in place.

See Fig. 17 and Fig. 18 for details.

2

Fig. 17

Rev 1.1

Fig. 18

12

14. Determine the position of both Side

panels (01).

NOTE:

a) Narrow side of the Side panel

cannot be trimmed and should face
the corner of the side wall.

b) Wide side of the Side panel can be

trimmed to size of your
measurements and should face the
front of the tub.

Place a mark on the wide side of the
Side panel with a distance of D – 1”
from the corner side of the Side panel
to the front edge and draw a straight
line from top to bottom.

See Fig. 19 for details.

D -1”

D -1”

15. Place the Side panel (01) on a flat piece of

plywood or a particle board. Cut the side end of
the Side panel by making a few deep scratches
with a sharp industrial knife using a T-Square tool
or a handheld jig saw.

See Fig. 20 and Fig. 21 for details.

Fig. 19

1

2

Rev 1.1

Fig. 20

13

D -1”

D -1”

16. Place the marks on the Side panel (01) which is

going to the side wall with the fixtures according to
the taken measurements in Fig. 4.
Drill the holes in the Side panel. Mind using the
proper diameter saw bit or a handheld jig saw.

See Fig. 22 and Fig. 23 for details.

Fig. 21

Rev 1.1

Fig. 22

14

17. Apply the sealant to the back surface of

the Side panel (01).
Apply the sealant around the drilled
holes and to the whole back side of the
Side panel.

See Fig. 24 for details.

Fig. 23

Rev 1.1

Fig. 24

15

18. Slide the edge of the Side

panel (01) all the way

behind the Corner cover (04)
and push the Side panel
against the wall.
Align the top of the Side
panel with the Back panel
before the sealant sets.
Apply equal pressure to the
whole surface of the Side
panel from top to bottom.
Peel off the adhesive tape on
the back side of the

Decorative edge molding
(03) and attach it to the

front edge of the Side panel.
Apply pressure to the

Decorative edge molding

from top to bottom.
See Fig. 25 for details.

1

2

3

4

NOTICE:

1

If you are installing a shower door with the
wall profile, you can hide the edge of the Side

Wall Profile

panel (01) behind the wall profile.

Side Panel

See Fig. 26 for details.

Wall

2

Side Panel

Wall Profile

Fig. 25

Rev 1.1

Fig. 26

16

19. Apply the sealant to the back

surface of the Side panel (01)
for another side wall installation.

See Fig. 27 for details.

1

20. Repeat Step 18 to install the

second Side panel.

See Fig. 28 and Fig. 29 for
details.

2

Fig. 27

3

4

Rev 1.1

Fig. 28

17

21. Fasten tight the Corner covers (04) and the

Center cover (05) to secure the Side panels (01)

and the Back panels (02) in place.

See Fig. 28 for details.

Fig. 29

1

2

Rev 1.1

Fig. 28

18

22. Use decorative plugs to cover the screw holes

in the Corner covers (04) and the Center
cover (05).

See Fig. 29 for details.

1

2

23. Apply caulk along the top edge of

the panels and along the
connection of the bottom edges of
the panels with the tub.

See Fig. 30 for details.

ATTENTION:

Installation of QWALL-Tub is
complete.
If you want to install Glass shelves
(09) to your Tub Wall, follow to
the next step.

Fig. 29

Rev 1.1

Fig. 30

19

Tub Glass Shelves Installation Instruction

24. Find the desirable height for the

Glass shelves (09) and mark the
locations on the wall.

NOTE:

The Glass shelves can be installed
either two in one corner, or one in
each.

See Fig. 31 for details.

G

H

Fig. 31

25. Mark the location for the Shelf brackets (10) according to

the measurements in Fig. 32.1.
Drill the holes using Ø5/16” drill bit and insert the Wall

anchors (06).

See Fig. 32 for details.

3½”

3

Ø 5/16”

2

3

½”

3

½”

1

Fig. 32

Rev 1.1

20

10. Mount the Glass brackets (10) to the wall using the

Countersunk screws ST4.2×30.

NOTE: padded set screw of the Glass bracket should be

facing down.

Slide the upper Glass shelf (09) into the Glass brackets and
tighten the set screws at the bottom of the brackets. Then
slide the bottom Glass shelf in place. Tighten the set screws
as well.

See Fig. 33 and Fig. 34 for details.

1

2

3

Fig. 33

Fig. 34

Rev 1.1

21

Product maintenance

To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth.
To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive
cleansers, metal brushes or scrapers that could scratch or dull the surface.

Acrylic cleaning procedure:

Acrylic should be cleaned with warm water and a clean, nonabrasive cloth. If desired, a mild,
nonabrasive detergent may also be used. Use only light pressure when cleaning. Avoid
rubbing dirt or grit into the surface. Turn the cloth often and replace with a clean cloth
frequently. Dry by blotting gently with a clean, dry cloth.

DO NOT USE:

Window cleaning sprays, alcohol, kitchen abrasive compounds, or solvents (such as acetone,
gasoline, or thinners). Do not use ammonia based cleaning solutions on the acrylic as it will
eat into the surface and cause it to damage.

How do you get scratches out of Acrylic?
For light scratches, use a buffing compound such as a car wax. Use the buffer or slightly
buff the surface by hands until scratches disappear.

Rev 1.1

22

WARRANTY

DREAMLINE™ LIMITED WARRANTY

This is Bath Authority LLC’s (“DreamLine”) exclusive written warranty effective April 2, 2012

This warranty extends only to the original owner/end-user for household use only and is not transferable to a subsequent owner. This warranty applies only
to DreamLine™ products purchased from an authorized dealer and installed in United States or Canada. Proof of purchase (original sales receipt) must be
provided with all warranty claims. In no event shall the liability of DreamLine™ exceed the purchase price of the unit.

If DreamLine™ shower & tub doors, shower enclosures and shower bases are used commercially, DreamLine™ warrants such products to be free from
defects in material and workmanship for one (1) year from initial date of purchase from an authorized dealer, with all other terms of this warranty applying
except duration. If DreamLine™ vanities, vessel sinks and shower columns are used commercially, DreamLine™ warrants such products to be free from
defects in material and workmanship for three (3) months from initial date of purchase from an authorized dealer, with all other terms of this warranty ap­plying except duration. DreamLine™ Jetted and Steam Shower Cabins are not intended for commercial use and there is no warranty extended
for these products for commercial use.

DreamLine™ hereby disclaims all warranties for products sold as dealer or store displays. DreamLine™ hereby disclaims all warranties for products used outside of

the United States or Canada whether expressed or implied, including but not limited to the implied warranties of merchantability and tness for a particular purpose.

DreamLine™ will, at its election, repair, replace with product of equal value or make appropriate adjustment where DreamLine’s analysis or inspection of
warranty claim discloses any such defects occurring in normal usage within the warranty period. DreamLine warranty obligation shall be discharged upon
tender of replacement or repair. Purchaser’s refusal to accept the tender terminates warranty obligation.

Cost of freight for returning products to DreamLine™ for repairs or replacement under this limited warranty are the responsibility of the customer. Cost of
freight associated with shipping of replacement product or parts to the customer may be charged to customer. Any product replaced or repaired during the
warranty period will be covered only for the remaining period of the original warranty. In no event will DreamLine be liable for costs of repair or replacement
of any installation material, including but not limited to tiles, marble, etc. DreamLine™ is not responsible for installation, removal or reinstallation

costs of any product requiring warranty services.

Improper modication or alteration of any DreamLine™ products will void the warranty. DreamLine product installations and repairs must be performed
by either a DreamLine authorized agent or a licensed experienced professional contractor - installation or repairs performed by any other party shall void
the warranty. This warranty shall not apply to breakage or damages caused by normal wear and tear, fault, carelessness, abuse, misuse, misapplication,
improper maintenance, alteration or modication of the unit, as well as chemical or natural corrosion, accident, re, ood, act of God or any other casu­alty. Improper care and cleaning will void the warranty. Use of cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents

or other products not recommended for chrome or similar nish, glass or acrylic will void the warranty. For additional product maintenance instructions

please refer to product installation manual. DreamLine™ is not responsible for any issues arising in connection with errors or omissions in information
provided on DreamLine’s websites. The warranty does not extend to any non-DreamLine™ plumbing or components installed by installers, end users
or by any party other than DreamLine™.

THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BATH AIU­THORITY LLC (“DREAMLINE”) AND/OR SELLER DISCLAIM ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. DREAMLINE™ IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGE, LOSS OF USE, LOSS OF TIME, LOSS OF PROFITS, INCONVENIENCE,
INCIDENTAL EXPENSES, LABOR OR MATERIAL CHARGES, OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS
PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY, OR RESULTING FROM THE REMOVAL OR
REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY.

DreamLine™ is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is
excluded from this warranty. DreamLine™ reserves the right to modify this warranty at any time - such warranty modication will not alter warranty ap-

plicable at the time of sale of the products in question. The warranty terms for specic products are:

SHOWER & TUB DOORS, SHOWER ENCLOSURES AND SHOWER BASES

DreamLine™ warrants shower & tub doors, shower enclosures and shower bases to be free from defects in workmanship and materials under

normal residential use for a period of ve (5) years from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.

SHOWER CABINS (JETTED & STEAM)

DreamLine™ warrants glass, acrylic and nish to be free from defects in workmanship for a period of ve (5) years from initial date of purchase by

the owner/end-user, contractor or builder from an authorized dealer; and plumbing, electrical and steam generator components for a period of
one (1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.

SHOWER COLUMNS

DreamLine™ warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one
(1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.

VANITIES AND VESSEL SINKS

DreamLine™ warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use
for a period of one (1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.

Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential

damages, so these limitations and exclusions may not apply to you. This warranty gives you specic legal rights. You may also have other rights, which

vary from state/province to state/province.

© 2012 Bath Authority LLC.
All Rights Reserved.

TEL: [phone]

FAX: [phone]

WWW.

BATHAUTHORITY.COM

For more information on DreamLineTM Tub Back Wall please visit www.BathAuthority.com

Rev 1.1

24