DrayTek VigorFly 210 Quick Install Guide

VViiggoorrFFllyy 221100 SSeerriieess

QQuuiicckk SSttaarrtt GGuuiiddee

Version: 1.1

Date: July 09, 2014

Warranty

We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) year
from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the
warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at
our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem
necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent
product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with,
damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other
vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.

European Community Declarations

Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product: VigorFly 210

DrayTek Corp. declares that VigorFly 210 is in compliance with the following essential requirements and other relevant provisions of R&TTE
Directive 1999/5/EC.

The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set
forth in EN55022/Class B and EN55024/Class

The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the requirements set forth in EN60950-1.

B.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.

This product is designed for 2.4GHz WLAN network throughout the EC region and Switzerland with restrictions in France. The antenna/transmitter

should be kept at least 20 cm away from human body.

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to
operate the equipment.

FCC RF Radiation Exposure Statement

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Package Content

Quick Start Guide CD

RJ-45 Cable (Ethernet)

The type of the power adapter depends on the country that the router will be
installed:

UK-type power adapter

EU-type power adapter

USA/Taiwan-type power adapter

AU/NZ-type Power Adapter

Descriptions of Components

LED Status Explanation

LAN 1 - 4

WLAN
(Blue LED) on

WLAN button

WPS
(Orange LED)

on WLAN
button

Off The system is not ready or is failed. ACT
Blinking The system is ready and can work normally.
On A USB device is connected and active. USB
Blinking The data is transmitting.
On The WAN port is connected. WAN
Blinking It will blink while transmitting data.
On A normal connection is through its corresponding

port.

Off LAN is disconnected.
Blinking Data is transmitting (sending/receiving).
On Wireless access point is ready.
Off Wireless access point is not ready.
Blinking

Blink when wireless traffic goes through.

(Blue)
Off The WPS is off.
Blinking

(Orange)

Blink with 1 second cycle for 2 minutes - - WPS is
enabled and waiting for wireless client to connect
with it.

Blinking

Blink when wireless traffic goes through.

(Orange)

WPS Button Press this button for 2 seconds to wait for client device making

network connection through WPS. When the orange LED lights
up, the WPS will be on.