Draytek Vigor2762 series User Manual

Download

Page 1

Page 2

Vigor2762 Series

ADSL2/2+ & VDSL2 Router

User’s Guide

Version: 1.0 (UK)

Firmware Version: V3.8.8 BT

(For future updates, please visit www.draytek.co.uk/support)

Date: April 12, 2018

Vigor2762 Series User’s Guide

Page 3

Note: The product specification is subject to continuous evolution which may not always be

reflected in current documentation. For the formal and supported current specification,

please refer only to the web site at www.draytek.co.uk

Vigor2762 Series User’s Guide

iii

Page 4

Copyrights

© All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.

Trademarks

The following trademarks are used in this document:

 Microsoft is a registered trademark of Microsoft Corp.

 Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8, 10 and Explorer are trademarks of Microsoft

Corp.

 Apple and Mac OS are registered trademarks of Apple Inc.

 Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions

 Read the installation guide thoroughly before you set up the router.

 The router is a complicated electronic unit that may be repaired only be authorized and qualified

personnel. Do not try to open or repair the router yourself.

 Do not place the router in a damp or humid place, e.g. a bathroom.

 The router should be used in a sheltered area, within a temperature range of +5 to +40 Celsius.

 Do not expose the router to direct sunlight or other heat sources. The housing and electronic components

may be damaged by direct sunlight or heat sources.

 Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.

 Keep the package out of reach of children.

 When you want to dispose of the router, please follow local regulations on conservation of the

environment.

Warranty

 We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship

or materials for a period of two (2) years from the date of purchase from a DrayTek authorized dealer in the UK/Ireland. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labour, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by external factors, used with unapproved accessories or subjected to abnormal working conditions. Warranty applies to hardware only, not software or firmware. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

Join the UK mailing list

 Users in the UK & Ireland can sign up to our mailing list which goes out approximately 4 times per year with

products news, updates, hints & tips and offers. For details, please visit www.draytek.co.uk/list

Firmware & Tools Updates

 Due to the continuous evolution of DrayTek technology and emerging risks, router firmware updates may be

issued. Please consult the DrayTek web site for more information on newest firmware, tools and documents: www.draytek.co.uk (For UK/Ireland)

Vigor2762 Series User’s Guide

Page 5

Table of

Contents

Part I Installation............................................................................................1

I-1 Introduction........................................................................................................2

I-1-1 Indicators and Connectors..................................................................................................3

I-2 Hardware Installation........................................................................................5

I-2-1 Installing Vigor Router......................................................................................................... 5

I-2-2 Wall-Mounted Installation.................................................................................................... 6

I-2-3 Installing USB Printer to Vigor Router................................................................................. 6

I-3 Accessing Web Page.......................................................................................15

I-4 Changing Password........................................................................................17

I-5 Dashboard........................................................................................................18

I-5-1 Virtual Panel..................................................................................................................... 18

I-5-2 Name with a Link.............................................................................................................. 19

I-5-3 Quick Access for Common Used Menu............................................................................20

I-5-4 GUI Map........................................................................................................................... 21

I-5-5 Web Console.................................................................................................................... 22

I-5-6 Config Backup................................................................................................................... 23

I-5-7 Logout............................................................................................................................... 23

I-5-8 Online Status.................................................................................................................... 24

I-5-8-1 Physical Connection........................................................................................... 24

I-5-8-2 Virtual WAN........................................................................................................ 26

I-6 Quick Start Wizard...........................................................................................27

I-6-1 For WAN1 (ADSL)............................................................................................................ 28

I-6-2 For WAN2 (Ethernet)........................................................................................................ 32

I-6-3 For WAN3 (USB).............................................................................................................. 42

I-7 Service Activation Wizard...............................................................................44

I-8 Registering Vigor Router................................................................................46

Part II Connectivity......................................................................................48

II-1 WAN..................................................................................................................49

II-1-1 General Setup.................................................................................................................. 51

II-1-1-1 WAN1 (ADSL/VDSL)......................................................................................... 52

II-1-1-2 WAN2 (Ethernet)...............................................................................................54

II-1-1-3 WAN3 / WAN4 (USB)........................................................................................ 55

II-1-2 Internet Access................................................................................................................ 57

II-1-2-1 Details Page for PPPoE/PPPoA in WAN1 (Physical Mode: ADSL)...................59

II-1-2-2 Details Page for MpoA/Static or Dynamic IP in WAN1 (Physical Mode: ADSL) 62

II-1-2-3 Details Page for PPPoE in Ethernet WAN.........................................................65

II-1-2-4 Details Page for Static or Dynamic IP in Ethernet WAN....................................67

II-1-2-5 Details Page for PPTP/L2TP in Ethernet WAN..................................................71

II-1-2-6 Details Page for 3G/4G USB Modem (PPP mode) in USB WAN.......................72

II-1-2-7 Details Page for 3G/4G USB Modem (DHCP mode) in USB WAN....................75

Vigor2762 Series User’s Guide

Page 6

II-1-2-8 Details Page for IPv6 – Offline in WAN1/WAN2/WAN3.....................................77

II-1-2-9 Details Page for IPv6 – PPP in WAN1/WAN2...................................................77

II-1-2-10 Details Page for IPv6 – TSPC in WAN1/WAN2/WAN3....................................78

II-1-2-11 Details Page for IPv6 – AICCU in WAN1/WAN2/WAN3..................................80

II-1-2-12 Details Page for IPv6 – DHCPv6 Client in WAN1/WAN2.................................82

II-1-2-13 Details Page for IPv6 – Static IPv6 in in WAN1/WAN2....................................83

II-1-2-14 Details Page for IPv6 – 6in4 Static Tunnel in WAN1 / WAN2..........................85

II-1-2-15 Details Page for IPv6 – 6rd in WAN1 / WAN2.................................................87

II-1-3 Multi-PVC/VLAN.............................................................................................................. 89

II-1-4 WAN Budget.................................................................................................................... 94

II-1-4-1 General Setup...................................................................................................94

II-1-4-2 Status................................................................................................................97

Application Notes...................................................................................................................... 98

A-1 How to assign an IPv6 address to LAN clients?......................................................98

A-2 How to configure IPv6 on WAN interface?.............................................................101

II-2 LAN.................................................................................................................106

II-2-1 General Setup................................................................................................................ 108

II-2-1-1 Details Page for LAN1 – Ethernet TCP/IP and DHCP Setup...........................110

II-2-1-2 Details Page for LAN1~ LAN2 – IPv6 Setup....................................................112

II-2-1-3 Details Page for LAN2.....................................................................................115

II-2-2 VLAN............................................................................................................................. 117

II-2-3 Bind IP to MAC.............................................................................................................. 119

II-2-4 LAN Port Mirror.............................................................................................................. 122

II-3 Hardware Acceleration.................................................................................123

II-3-1 Setup............................................................................................................................. 123

II-4 NAT.................................................................................................................126

II-4-1 Port Redirection............................................................................................................. 127

II-4-2 DMZ Host....................................................................................................................... 131

II-4-3 Open Ports..................................................................................................................... 133

II-4-4 Port Triggering............................................................................................................... 135

II-4-5 ALG................................................................................................................................ 137

II-5 Applications..................................................................................................139

II-5-1 Dynamic DNS................................................................................................................ 140

II-5-2 LAN DNS / DNS Forwarding.......................................................................................... 143

II-5-3 DNS Security................................................................................................................. 146

II-5-3-1 General Setup.................................................................................................146

II-5-3-2 Domain Diagnose............................................................................................147

II-5-4 Schedule........................................................................................................................ 147

II-5-5 UPnP............................................................................................................................. 151

II-5-6 IGMP.............................................................................................................................. 152

II-5-6-1 General Setting................................................................................................ 152

II-5-6-2 Working Group................................................................................................153

II-5-7 Wake on LAN................................................................................................................. 154

II-5-8 SMS / Mail Alert Service................................................................................................ 155

II-5-8-1 SMS Alert........................................................................................................ 155

II-5-8-2 Mail Alert.......................................................................................................... 156

Vigor2762 Series User’s Guide

Page 7

II-5-9 Bonjour.......................................................................................................................... 157

Application Notes.................................................................................................................... 160

A-1 How to Configure Customized DDNS?.................................................................. 160

Part III Wireless LAN..................................................................................164

III-1 Wireless LAN................................................................................................165

III-1-1 Wireless Wizard............................................................................................................ 168

III-1-2 General Setup............................................................................................................... 171

III-1-3 Security......................................................................................................................... 172

III-1-4 Access Control.............................................................................................................. 174

III-1-5 WPS.............................................................................................................................. 176

III-1-6 WDS............................................................................................................................. 179

III-1-7 Advanced Setting.......................................................................................................... 182

III-1-8 Station Control.............................................................................................................. 184

III-1-8 Bandwidth Management............................................................................................... 185

III-1-9 AP Discovery................................................................................................................ 186

III-1-10 Airtime Fairness.......................................................................................................... 187

III-1-11 Roaming..................................................................................................................... 188

III-1-12 Station List.................................................................................................................. 189

Part IV VPN.................................................................................................192

IV-1 VPN and Remote Access............................................................................193

IV-1-1 Remote Access Control................................................................................................ 194

IV-1-2 PPP General Setup...................................................................................................... 194

IV-1-3 IPsec General Setup.................................................................................................... 196

IV-1-4 IPsec Peer Identity....................................................................................................... 197

IV-1-5 Remote Dial-in User..................................................................................................... 199

IV-1-6 LAN to LAN.................................................................................................................. 202

IV-1-9 Connection Management............................................................................................. 210

Application Notes.................................................................................................................... 211

A-1 How to Build a LAN-to-LAN VPN Between Vigor Routers via IPsec Main Mode...211

IV-2 SSL VPN.......................................................................................................216

IV-2-1 General Setup.............................................................................................................. 217

IV-2-2 User Account................................................................................................................ 218

IV-2-3 Online User Status....................................................................................................... 222

IV-3 Certificate Management..............................................................................223

IV-3-1 Local Certificate............................................................................................................ 224

IV-3-2 Trusted CA Certificate.................................................................................................. 228

IV-3-3 Certificate Backup........................................................................................................ 230

Part V Security...........................................................................................231

Vigor2762 Series User’s Guide

vii

Page 8

V-1 Firewall..........................................................................................................232

V-1-1 General Setup............................................................................................................... 234

V-1-2 Filter Setup.................................................................................................................... 239

V-1-3 DoS Defense................................................................................................................. 247

V-1-4 Diagnose....................................................................................................................... 252

Application Notes.................................................................................................................... 255

A-1 How to Configure Certain Computers Accessing to Internet..................................255

V-2 CSM (Central Security Management).........................................................259

V-2-1 APP Enforcement Profile............................................................................................... 260

V-2-2 APPE Signature Upgrade.............................................................................................. 262

V-2-3 URL Content Filter Profile.............................................................................................. 263

V-2-4 Web Content Filter Profile............................................................................................. 267

V-2-5 DNS Filter Profile........................................................................................................... 271

V-2-6 APPE Support List......................................................................................................... 273

Application Notes.................................................................................................................... 274

A-1 How to Create an Account for MyVigor..................................................................274

A-2 How to Block Facebook Service Accessed by the Users via Web Content Filter /

URL Content Filter....................................................................................................... 282

Part VI Management...................................................................................287

VI-1 System Maintenance...................................................................................288

VI-1-1 System Status.............................................................................................................. 289

VI-1-2 TR-069......................................................................................................................... 291

VI-1-3 Admin Setting............................................................................................................... 293

VI-1-4 User Password............................................................................................................. 296

VI-1-5 Login Page Greeting..................................................................................................... 299

VI-1-6 Configuration Backup................................................................................................... 301

VI-1-7 SysLog/Mail Alert.......................................................................................................... 304

VI-1-8 Time and Date.............................................................................................................. 307

VI-1-9 SNMP........................................................................................................................... 308

VI-1-10 Management............................................................................................................... 310

VI-1-11 Self-Signed Certificate................................................................................................ 314

VI-1-12 Reboot System........................................................................................................... 316

VI-1-13 Firmware Upgrade...................................................................................................... 317

VI-1-14 Modem Code Upgrade............................................................................................... 317

VI-1-15 Activation.................................................................................................................... 318

Application Notes.................................................................................................................... 320

A-1 How to prevent CPE's settings from being changed by the end-users?................320

VI-2 Bandwidth Management.............................................................................323

VI-2-1 Sessions Limit.............................................................................................................. 325

VI-2-2 Bandwidth Limit............................................................................................................ 327

VI-2-3 Quality of Service......................................................................................................... 329

Vigor2762 Series User’s Guide

viii

Page 9

VI-2-4 APP QoS...................................................................................................................... 336

Application Notes.................................................................................................................... 338

A-1 How to Optimize the Bandwidth through QoS Technology....................................338

VI-3 Central Management (AP)..........................................................................343

VI-3-1 Status........................................................................................................................... 344

VI-3-2 WLAN Profile................................................................................................................ 345

VI-3-3 AP Maintenance........................................................................................................... 350

VI-3-4 Traffic Graph................................................................................................................. 351

VI-3-5 Load Balance................................................................................................................ 352

VI-3-6 Function Support List.................................................................................................... 354

Part VII Others............................................................................................355

VII-1 Objects Settings.........................................................................................356

VII-1-1 IP Object...................................................................................................................... 356

VII-1-2 IP Group...................................................................................................................... 360

VII-1-3 IPv6 Object.................................................................................................................. 361

VII-1-4 IPv6 Group.................................................................................................................. 363

VII-1-5 Service Type Object.................................................................................................... 364

VII-1-6 Service Type Group..................................................................................................... 366

VII-1-7 Keyword Object........................................................................................................... 368

VII-1-8 Keyword Group............................................................................................................ 370

VII-1-9 File Extension Object................................................................................................... 371

VII-1-10 SMS/Mail Service Object........................................................................................... 373

VII-1-11 Notification Object..................................................................................................... 377

VII-1-12 String Object.............................................................................................................. 378

Application Notes.................................................................................................................... 380

A-1 How to Send a Notification to Specified Phone Number via SMS Service in WAN

Disconnection............................................................................................................... 380

VII-2 USB Application.........................................................................................384

VII-2-1 USB General Settings................................................................................................. 384

VII-2-2 USB User Management............................................................................................... 385

VII-2-3 File Explorer................................................................................................................ 387

VII-2-4 USB Device Status...................................................................................................... 388

VII-2-5 Temperature Sensor.................................................................................................... 389

VII-2-6 Modem Support List.................................................................................................... 391

VII-2-6 SMB Client Support List.............................................................................................. 392

VII-2-7 SMB Client Support List.............................................................................................. 393

Application Notes.................................................................................................................... 394

A-1 How can I get the files from USB storage device connecting to Vigor router?.......394

Part VIII Troubleshooting..........................................................................398

VIII-1 Diagnostics................................................................................................399

Vigor2762 Series User’s Guide

Page 10

VIII-1-1 Dial-out Triggering......................................................................................................399

VIII-1-2 Routing Table............................................................................................................. 401

VIII-1-3 ARP Cache Table....................................................................................................... 402

VIII-1-4 IPv6 Neighbour Table................................................................................................. 402

VIII-1-5 DHCP Table............................................................................................................... 403

VIII-1-6 NAT Sessions Table................................................................................................... 403

VIII-1-7 DNS Cache Table....................................................................................................... 405

VIII-1-8 Ping Diagnosis............................................................................................................ 406

VIII-1-9 Data Flow Monitor...................................................................................................... 407

VIII-1-10 Traffic Graph............................................................................................................. 410

VIII-1-11 Trace Route.............................................................................................................. 411

VIII-1-12 Syslog Explorer........................................................................................................ 412

VIII-1-13 IPv6 TSPC Status..................................................................................................... 413

VIII-1-14 DSL Status............................................................................................................... 413

VIII-1-15 DoS Flood Table....................................................................................................... 414

VIII-1-16 Route Policy Diagnosis............................................................................................. 417

VIII-2 Checking If the Hardware Status Is OK or Not.......................................419

VIII-3 Checking If the Network Connection Settings on Your Computer Is OK

or Not....................................................................................................................420

VIII-4 Pinging the Router from Your Computer................................................423

VIII-5 Checking If the ISP Settings are OK or Not............................................425

VIII-6 Problems for 3G/4G Network Connection..............................................426

VIII-7 Backing to Factory Default Setting If Necessary...................................427

VIII-8 Contacting DrayTek...................................................................................429

VIII-8-1 Getting further help..................................................................................................... 429

VIII-8-2 Additional Feature Setup............................................................................................429

VIII-8-3 Keep up to date with our mailing list...........................................................................429

VIII-8-4 Firmware Updates...................................................................................................... 430

VIII-8-5 Security & Router Best Practice.................................................................................430

Appendix I: VLAN Applications on Vigor Router.............................................431

Part IX DrayTek Tools................................................................................439

X-1 SmartVPN Client...........................................................................................440

X-1-1 DrayTek Android-based SmartVPN for SSL VPN tunnels.............................................440

X-1-2 How to Use SmartVPN Android APP to Establish SSL VPN Tunnel?...........................441

Part X Telnet Commands...........................................................................445

Accessing Telnet of Vigor2762..........................................................................446

Vigor2762 Series User’s Guide

Page 11

Part I Installation

This part will introduce Vigor router and guide to install the device in hardware and software.

Vigor2762 Series User’s Guide

Page 12

I-1 Introduction

The Vigor2762 series is an ADSL2+ / VDSL2 router / firewall with guest network capability for fast and secure home and small office connectivity, designed for bandwidth-intensive applications such as high-definition video streaming, online gaming and Internet telephony.

Packed with advanced features, the Vigor 2762 series offers truly comprehensive DSL connectivity and security. Compatible with all UK variants of ADSL (including ADSL2+ and Annex M), VDSL2 (BT Infinity™/FTTC), the Vigor 2762 can also be used for cable-modem or fibre connections, using its GigaLAN 4 port in Ethernet WAN mode and 3G/4G cellular service using a supported USB modem.

A 4-port Gigabit Ethernet switch on the LAN side provides high speed connectivity for your computers or network storage (NAS) devices and can connect a VigorAP wireless access point or network switch with 802.1Q VLAN tagging. Comprehensive security features include content filtering, web application controls and an object based firewall management system.

GlobalView Web Content Filtering allows blocking of websites based on the category they’re determined to fit in, which is managed by the GlobalView servers, making it far simpler to block unwanted sites (e.g. Gambling and adult categories) with less maintenance required as new or changed site categorisations are continuously updated. A free 30-day trial is included with your new router.

Advanced IP based Quality of Service, Bandwidth Management and WAN Budget facilities make it possible to control bandwidth usage fairly on your network, prioritising important traffic such as Voice over IP over bulk downloads and making it possible to limit network segments, such as the guest network from over-using bandwidth.

The router’s hardware accelerated IPSec/SSL/L2TP VPN (Virtual Private Networking) functionality can dial-out quickly and securely to an office VPN server for teleworking.

The SSL VPN server allows you to connect your computer, phone or tablet into your home network from anywhere, with access to network storage and secure Internet connectivity through the SSL VPN tunnel.

Two USB ports allow for connection of USB Printers, USB Storage (for Samba or FTP usage) for basic NAS functionality, USB Modem for Internet connectivity or a USB Temperature sensor to monitor temperatures remotely and warn if the temperature goes outside of the desired range.

Vigor2762 Series User’s Guide

Page 13

I-1-1

Indicators

and Connectors

Before you use the Vigor router, please get acquainted with the LED indicators and connectors first.

LED Status Explanation

(Activity)

Blinking The router is ready and operating normally Off The router is powered off.

(2.4GHz Wireless LAN On/Off/WPS)

On (Green) 2.4GHz Access Point is active Blinking

(Green)

Data is being transmitted on the router’s 2.4 GHz wireless interface

Blinking (Orange)

WPS pairing mode is active for two minutes

Off The wireless access point is turned off.

(5GHz Wireless LAN On/Off/WPS)

On (Green) 5GHz Access Point is turned off Blinking

(Green)

Data is being transmitted on the router’s 5GHz wireless interface

Blinking (Orange)

WPS pairing mode is active for two minutes

(USB)

On USB device is connected and ready for use Blinking Data is being transmitted over USB

(DSL)

On DSL connection synchronised Blinking

(Slowly)

DSL connection not currently synchronising or not detected

Blinking (Quickly)

DSL connection is synchronising

(LAN1/2/3/4)

On Ethernet LAN (RJ45) is connected Blinking Data is transmitting (sending/receiving) Off Ethernet LAN is disconnected

Vigor2762 Series User’s Guide

Page 14

Vigor2762

Vigor2762n / Vigor2762ac

Interface Description

Factory Reset

Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press gently and hold

for more than 5 seconds. When the ACT LED blinks rapidly, release the button. Then the router will restart with the factory default configuration

WLAN ON/OFF/WPS

Press for less than 2 seconds to switch toggle the router’s wireless interfaces:

For example,

 2.4G (On) and 5G (On) – Default state.  2.4G (Off) and 5G (On) – press and release the button

once.

 2.4G (On) and 5G (Off) – press and release the button

twice.

 2.4G (Off) and 5G (Off) – press and release the button

three times.

When WPS is enabled in the router’s web interface, press this button for more than 2 seconds to enable WPS pairing mode.

USB1~USB2 Connector for a USB 3G/4G modem, storage, printer or USB

Thermometer

GigaLAN1~LAN4 RJ-45 Gigabit Ethernet connectors for local network devices.

GigaLAN4 can be configured as the Ethernet WAN port, see Section 5.3 for details

DSL

RJ-11 connector for ADSL or VDSL line

I / O

Power Switch. Turns the unit on (I) or off (O)

PWR Connector for the power adapter

Vigor2762 Series User’s Guide

Page 15

I-2 Hardware Installation

I-2-1 Installing Vigor Router

1. ADSL/VDSL Connections: Connect the DSL port to the Modem or DSL port of the external splitter/microfilter (not supplied) with the RJ-11 line cable. In some cases, your RJ-11 DSL socket will be built-into your phone line socket on the wall and you won’t have a separate microfilter/splitter.

2. LAN Connections: Connect a LAN port of the router to your computer or switch.

3. Wireless Antennas: Connect the wireless antennas to the router

4. Power Supply: Connect the power adapter to the Vigor 2762’s PWR socket on the rear and plug the power adapter into a suitable mains socket.

5. Turn the Vigor 2762 on using its power switch.

6. The router will start up. After completing the system test, the ACT LED will light up and start blinking once per second to indicate that it is ready for use.

7. Ethernet-based Internet Connections: The GigaLAN4 port can be switched to operate as the Ethernet WAN port. This must be configured in the router’s web interface before it can operate in this mode – Section II-1-1-2 details how to do that. With the GigaLAN4 port configured for Ethernet WAN mode, connect the cable Modem/DSL Modem/Media Converter to the WAN port of the router with Ethernet cable (RJ-45).

Vigor2762 Series User’s Guide

Page 16

I-2-2 Wall-Mounted Installation

Vigor2762 has keyhole type mounting slots on the underside.

1. A template is provided on the Vigor2762 packaging box to enable you to space the screws correctly on the wall.

2. Place the template on the wall and drill the holes according to the recommended instruction.

3. Fit screws into the wall using the appropriate type of wall plug.

Note

The recommended drill diameter shall be 6.5mm (1/4”).

4. When you finished about procedure, the router has been mounted on the wall firmly.

I-2-3 Installing USB Printer to Vigor Router

You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows 7. For other Windows system, please visit www.DrayTek.com.

Vigor2762 Series User’s Guide

Page 17

Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).

1. Connect the printer with the router through USB/parallel port.

2. Open All Programs>>Getting Started>>Devices and Printers.

3. Click Add a printer.

4. A dialog will appear. Click Add a local printer and click Next.

Vigor2762 Series User’s Guide

Page 18

5. In this dialog, choose Create a new port. In the field of Type of port, use the drop

down list to select Standard TCP/IP Port. Then, click Next.

Vigor2762 Series User’s Guide

Page 19

6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Hostname or

IP Address and type 192.168.1.1 as the Port name. Then, click Next.

7. Click Standard and choose Generic Network Card.

Vigor2762 Series User’s Guide

Page 20

8. Now, your system will ask you to choose right name of the printer that you installed

onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next.

9. Type a name for the chosen printer. Click Next.

Vigor2762 Series User’s Guide

Page 21

10. Choose Do not share this printer and click Next.

11. Then, in the following dialog, click Finish.

Vigor2762 Series User’s Guide

Page 22

12. The new printer has been added and displayed under Printers and Faxes. Click the

new printer icon and click Printer server properties.

13. Edit the property of the new printer you have added by clicking Configure Port.

Vigor2762 Series User’s Guide

Page 23

14. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next

please refer to the red rectangle for choosing the correct protocol and LPR name.

Vigor2762 Series User’s Guide

Page 24

The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router.

Info Note 1: Some printers with the fax/scanning or other additional functions are not

supported. If you do not know whether your printer is supported or not,

please visit www.draytek.com to find out the printer list. Open Support >FAQ/Application Notes; find out the link of USB>>Printer Server and click it.

Then, click the What types of printers are compatible with Vigor router? link.

Note 2: Vigor router supports printing request from computers via LAN ports but not WAN port.

Vigor2762 Series User’s Guide

Page 25

I-3 Accessing Web Page

1. Make sure your PC connects to the router correctly.

You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to the later section - Trouble Shooting of the guide.

2. Open a web browser on your PC and type http://192.168.1.1. The following window

will be open to ask for username and password.

3. Please type “admin/admin” as the Username/Password and click Login.

Info If you fail to access to the web configuration, please go to “Trouble Shooting” for

detecting and solving your problem.

Vigor2762 Series User’s Guide

Page 26

4. Now, the Main Screen will appear.

Info The home page will be different slightly in accordance with the type of the

router you have.

5. The web page can be logged out according to the chosen condition. The default

setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity.

Vigor2762 Series User’s Guide

Page 27

I-4 Changing Password

Please change the password for the original security of the router.

1. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will

open to ask for username and password.

2. Please type “admin/admin” as Username/Password for accessing into the web user

interface with admin mode.

3. Go to System Maintenance page and choose Administrator Password.

4. Enter the login password (the default is “admin”) on the field of Old Password. Type

New Password and Confirm Password. Then click OK to continue.

Info The maximum length of the password you can set is 23 characters.

5. Now, the password has been changed. Next time, use the new password to access the

Web user interface for this router.

Info Even the password is changed, the Username for logging onto the web user

interface is still “admin”.

Vigor2762 Series User’s Guide

Page 28

I-5 Dashboard

Dashboard shows the connection status including System Information, IPv4 Internet Access, IPv6 Internet Access, Interface (physical connection), Security and Quick Access.

Click Dashboard from the main menu on the left side of the main page.

A web page with default selections will be displayed on the screen. Refer to the following figure:

I-5-1 Virtual Panel

On the top of the Dashboard, a virtual panel (simulating the physical panel of the router) displays the physical interface connection. It will be refreshed every five seconds. When you move and click the mouse cursor on LEDs (except ACT), USB ports, LAN, or WAN, related web setting page will be open for you to configure if required.

Vigor2762 Series User’s Guide

Page 29

For detailed information about the LED display, refer to I-1-1 LED Indicators and Connectors.

I-5-2 Name with a Link

A name with a link (e.g., Router Name, Current Time, WAN1~4 and etc.) below means you can click it to open the configuration page for modification.

Vigor2762 Series User’s Guide

Page 30

I-5-3 Quick Access for Common Used Menu

All the menu items can be accessed and arranged orderly on the left side of the main page for your request. However, some important and common used menu items which can be accessed in a quick way just for convenience.

Look at the right side of the Dashboard. You will find a group of common used functions grouped under Quick Access.

The function links of System Status, Dynamic DDNS, TR-069, User Management, IM/P2P Block, Schedule, Syslog/Mail Alert, LDAP, RADIUS, Firewall Object Setting and Data Flow Monitor are displayed here. Move your mouse cursor on any one of the links and click on it. The corresponding setting page will be open immediately.

In addition, quick access for VPN security settings such as Remote Dial-in User and LAN to LAN are located on the bottom of this page. Scroll down the page to find them and use them if required.

Note that there is a plus ( ) icon located on the left side of VPN/LAN. Click it to review the VPN connection(s) used presently.

Vigor2762 Series User’s Guide

Page 31

Host connected physically to the router via LAN port(s) will be displayed with green circles in the field of Connected.

All of the hosts (including wireless clients) displayed with Host ID, IP Address and MAC address indicates that the traffic would be transmitted through LAN port(s) and then the WAN port. The purpose is to perform the traffic monitor of the host(s).

I-5-4 GUI Map

All the functions the router supports are listed with table clearly in this page. Users can click the function link to access into the setting page of the function for detailed configuration. Click the icon on the top of the main screen to display all the functions.

Vigor2762 Series User’s Guide

Page 32

I-5-5 Web Console

It is not necessary to use the telnet command via DOS prompt. The changes made by using web console have the same effects as modified through web user interface. The functions/settings modified under Web Console also can be reviewed on the web user interface.

Click the Web Console icon on the top of the main screen to open the following screen.

Vigor2762 Series User’s Guide

Page 33

I-5-6 Config Backup

There is one way to store current used settings quickly by clicking the Config Backup icon. It allows you to backup current settings as a file. Such configuration file can be restored by using System Maintenance>>Configuration Backup.

Simply click the icon on the top of the main screen to store the setting.

I-5-7 Logout

Click this icon to exit the web user interface.

Vigor2762 Series User’s Guide

Page 34

I-5-8 Online Status

I-5-8-1 Physical Connection

Such page displays the physical connection status such as LAN connection status, WAN connection status, ADSL information, and so on.

Physical Connection for IPv4 Protocol

Vigor2762 Series User’s Guide

Page 35

Physical Connection for IPv6 Protocol

Detailed explanation (for IPv4) is shown below:

Item Description

LAN Status Primary DNS-Displays the primary DNS server address for

WAN interface. Secondary DNS -Displays the secondary DNS server

address for WAN interface.

IP Address-Displays the IP address of the LAN interface. TX Packets-Displays the total transmitted packets at the

LAN interface. RX Packets-Displays the total received packets at the LAN

interface.

WAN1/WAN2/WAN3 /WAN4 Status

Enable – Yes in red means such interface is available but

not enabled. Yes in green means such interface is enabled.

Line – Displays the physical connection (VDSL, ADSL, Ethernet, or USB) of this interface.

Name – Display the name of the router. Mode - Displays the type of WAN connection (e.g., PPPoE). Up Time - Displays the total uptime of the interface. IP - Displays the IP address of the WAN interface. GW IP - Displays the IP address of the default gateway. TX Packets - Displays the total transmitted packets at the

WAN interface. TX Rate - Displays the speed of transmitted octets at the

WAN interface. RX Packets - Displays the total number of received

packets at the WAN interface.

Vigor2762 Series User’s Guide

Page 36

Item Description

RX Rate - Displays the speed of received octets at the

WAN interface.

Detailed explanation (for IPv6) is shown below:

Item Description

LAN Status IP Address- Displays the IPv6 address of the LAN interface..

TX Packets-Displays the total transmitted packets at the

LAN interface. RX Packets-Displays the total received packets at the LAN

interface. TX Bytes - Displays the speed of transmitted octets at the

LAN interface. RX Bytes - Displays the speed of received octets at the LAN

interface.

WAN IPv6 Status Enable – No in red means such interface is available but not

enabled. Yes in green means such interface is enabled. No in red means such interface is not available.

Mode - Displays the type of WAN connection (e.g., TSPC). Up Time - Displays the total uptime of the interface. IP - Displays the IP address of the WAN interface. Gateway IP - Displays the IP address of the default

gateway.

Info The words in green mean that the WAN connection of that interface is ready for

accessing Internet; the words in red mean that the WAN connection of that interface is not ready for accessing Internet.

I-5-8-2 Virtual WAN

Such page displays the virtual WAN connection information.

Virtual WAN are used by TR-069 management, VoIP service and so on.

The field of Application will list i-9the purpose of such WAN connection.

Vigor2762 Series User’s Guide

Page 37

I-6 Quick Start Wizard

Quick Start Wizard can help you to deploy and use the router easily and quickly. Click Wizards>>Quick Start Wizards. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.

On the next page as shown below, please select the WAN interface (WAN 1 to WAN3) that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if 3G/4G USB modem is used, please choose WAN3. For WAN2, choose Auto negotiation as the physical type for your router.

WAN1~ WAN3 will bring up different configuration page. Refer to the following sections for detailed information.

Vigor2762 Series User’s Guide

Page 38

I-6-1 For WAN1 (ADSL)

WAN1 is specified for ADSL or VDSL2 connection.

Available settings are explained as follows:

Item Description

Display Name Type a name to identify such WAN.

VLAN Tag insertion (VDSL2)/(ADSL)

The settings configured in this field are available for WAN1 and WAN2.

Enable – Enable the function of VLAN with tag. The router will add specific VLAN number to all packets on

the WAN while sending them out. Please type the tag value and specify the priority for the

packets sending by WAN1.

Disable – Disable the function of VLAN with tag. Tag value – Type the value as the VLAN ID number. The

range is from 0 to 4095. Priority – Type the packet priority number for such VLAN.

The range is from 0 to 7.

Please select the appropriate Internet access type according to the information from your ISP. Click Next.

PPPoE/PPPoA

PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable modem. All the users over the Ethernet can share a common connection.

PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection for accessing the Internet. Your service provider will provide you information about user name, password, and authentication mode.

1. Choose WAN1 as WAN Interface and click the Next button; you will get the following

page. Choose PPPoE XXXX or PPPoA XXXXX as the protocol.

Vigor2762 Series User’s Guide

Page 39

Available settings are explained as follows:

Item Description

Protocol / Encapsulation

Choose PPPoE/PPPoA for WAN1 interface.

VPI Type in the value provided by ISP.

Auto detect – Click this button to have the VPI and VCI to

be detected by the system automatically

VCI Type in the value provided by ISP.

Fixed IP Click Yes to enable Fixed IP feature.

IP Address Type the IP address if Fixed IP is enabled.

Primary DNS Type in the primary IP address for the router.

Secondary DNS Type in secondary IP address for necessity in the future.

Back Click it to return to previous setting page.

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

2. After finished the above settings, simply click Next.

Vigor2762 Series User’s Guide

Page 40

Available settings are explained as follows:

Item Description

Service Name (Optional)

Enter the description of the specific network service.

User Name Type in the valid user name (maximum 63 characters)

provided by the ISP in this field.

Password Type a valid password provided by the ISP.

Confirm Password Retype the password.

Back Click it to return to previous setting page.

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

3. Please manually enter the Username/Password provided by your ISP. Then click Next

for viewing summary of such connection.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

Vigor2762 Series User’s Guide

Page 41

5. Now, you can enjoy surfing on the Internet.

MPoA

1. Choose WAN1 as WAN Interface and click the Next button; you will get the following

page.

Available settings are explained as follows:

Item Description

Protocol There are two modes offered for you to choose for WAN1

interface. Choose MPoA as the protocol.

For ADSL Only Such field is provided for ADSL only. You have to choose

encapsulation and type the values for VPI and VCI. Or, click

Auto detect to find out the best values.

Fixed IP Click Yes to enable Fixed IP feature.

IP Address Type the IP address if Fixed IP is enabled.

Subnet Mask Type the subnet mask.

Default Gateway Type the IP address as the default gateway.

Primary DNS Type in the primary IP address for the router.

Secondary DNS Type in secondary IP address for necessity in the future.

Back Click it to return to previous setting page.

Vigor2762 Series User’s Guide

Page 42

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

2. Please type in the IP address/mask/gateway information originally provided by your

ISP. Then click Next for viewing summary of such connection.

3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

4. Now, you can enjoy surfing on the Internet.

I-6-2 For WAN2 (Ethernet)

WAN2 is dedicated to physical mode in Ethernet. Please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface.

Available settings are explained as follows:

Vigor2762 Series User’s Guide

Page 43

Item Description

Display Name Type a name for the router.

VLAN Tag insertion Enable – Enable the function of VLAN with tag.

The router will add specific VLAN number to all packets on the WAN while sending them out.

Please type the tag value and specify the priority for the packets sending by WAN2.

Disable – Disable the function of VLAN with tag. Tag value – Type the value as the VLAN ID number. The

range is form 0 to 4095. Priority – Type the packet priority number for such VLAN.

The range is from 0 to 7.

PPPoE

1. Choose WAN2 as the WAN Interface and click the Next button. The following page will

be open for you to specify Internet Access Type.

Vigor2762 Series User’s Guide

Page 44

2. Click PPPoE as the Internet Access Type. Then click Next to continue.

Available settings are explained as follows:

Item Description

Service Name (Optional)

Enter the description of the specific network service.

Username Assign a specific valid user name provided by the ISP.

Note: The maximum length of the user name you can set is

63 characters.

Password Assign a valid password provided by the ISP.

Note: The maximum length of the password you can set is

62 characters.

Confirm Password Retype the password.

Back Click it to return to previous setting page.

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

Vigor2762 Series User’s Guide

Page 45

3. Please manually enter the Username/Password provided by your ISP. Click Next for

viewing summary of such connection.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

5. Now, you can enjoy surfing on the Internet.

Vigor2762 Series User’s Guide

Page 46

PPTP/L2TP

1. Choose WAN2 as the WAN Interface and click the Next button. The following page will

be open for you to specify Internet Access Type.

2. Click PPTP/L2TP as the Internet Access Type. Then click Next to continue.

Available settings are explained as follows:

Item Description

Username Assign a specific valid user name provided by the ISP.

The maximum length of the user name you can set is 63 characters.

Password Assign a valid password provided by the ISP.

The maximum length of the password you can set is 62 characters.

Confirm Password Retype the password.

Vigor2762 Series User’s Guide

Page 47

WAN IP Configuration Obtain an IP address automatically – the router will get an

IP address automatically from DHCP server. Specify an IP address – you have to type relational settings

manually.

 IP Address - Type the IP address.  Subnet Mask –Type the subnet mask.  Gateway – Type the IP address of the gateway.  Primary DNS –Type in the primary IP address for the

router.

 Second DNS –Type in secondary IP address for

necessity in the future.

PPTP Server / L2TP Server

Type the IP address of the server.

Back Click it to return to previous setting page.

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

3. Please type in the IP address/mask/gateway information originally provided by your

ISP. Then click Next for viewing summary of such connection.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

5. Now, you can enjoy surfing on the Internet.

Vigor2762 Series User’s Guide

Page 48

Static IP

1. Choose WAN2 as the WAN Interface and click the Next button. The following page will

be open for you to specify Internet Access Type.

2. Click Static IP as the Internet Access type. Simply click Next to continue.

Available settings are explained as follows:

Item Description

WAN IP Type the IP address.

Subnet Mask Type the subnet mask.

Gateway Type the IP address of gateway.

Primary DNS Type in the primary IP address for the router.

Secondary DNS Type in secondary IP address for necessity in the future.

Back Click it to return to previous setting page.

Vigor2762 Series User’s Guide

Page 49

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

3. Please type in the IP address information originally provided by your ISP. Then click

Next for next step.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

5. Now, you can enjoy surfing on the Internet.

Vigor2762 Series User’s Guide

Page 50

DHCP

1. Choose WAN2 as WAN Interface and click the Next button. The following page will be

open for you to specify Internet Access Type.

2. Click DHCP as the Internet Access type. Simply click Next to continue.

Available settings are explained as follows:

Item Description

Host Name Type the name of the host.

Note: The maximum length of the host name you can set is

39 characters.

MAC Some Cable service providers specify a specific MAC address

for access authentication. In such cases you need to enter the MAC address.

Back Click it to return to previous setting page.

Next Click it to get into the next setting page.

Cancel Click it to give up the quick start wizard.

Vigor2762 Series User’s Guide

Page 51

3. After finished the settings above, click Next for viewing summary of such connection.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

5. Now, you can enjoy surfing on the Internet.

Vigor2762 Series User’s Guide

Page 52

I-6-3 For WAN3 (USB)

WAN3/WAN4 is dedicated to physical mode in USB.

1. Choose WAN3 as WAN Interface.

2. Then, click Next for getting the following page.

Available settings are explained as follows:

Item Description

Internet Access Choose one of the selections as the protocol of accessing

the internet.

3G/4G USB Modem (PPP mode)

SIM Pin code –Type PIN code of the SIM card that will be

used to access Internet. The maximum length of the pin code you can set is 15 characters.

Modem Initial String – Such value is used to initialize USB modem. Please use the default value. If you have any question, please contact to your ISP. The maximum length of the string you can set is 47 characters.

Vigor2762 Series User’s Guide

Page 53

APN Name – APN means Access Point Name which is provided and required by some ISPs. Type the name and click Apply.

3. Then, click Next for viewing summary of such connection.

4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system

status of this protocol will be shown.

5. Now, you can enjoy surfing on the Internet.

Vigor2762 Series User’s Guide

Page 54

I-7 Service Activation Wizard

Service Activation Wizard can guide you to activate WCF service (Web Content Filter) with a quick and easy way. For the Service Activation Wizard is only available for admin

operation, therefore, please type “admin/admin” on Username/Password while Logging into the web user interface.

Service Activation Wizard is a tool which allows you to use trial version of WCF directly without accessing into the server (MyVigor) located on http://myvigor.draytek.com. For using Web Content Filter Profile, please refer to later section Web Content Filter Profile for detailed information.

Now, follow the steps listed below to activate WCF feature for your router.

Info Such function is available only for Admin Mode.

1. Open Wizards>>Service Activation Wizard.

2. In the following page, you can activate the Web content filter services and APP

Enforcement service at the same time or individually. When you finish the selection, check the box of “I have read…” and click Next.

Info BPjM is web content filter (WCF) for German Speaking users. It is ideal for

your family to provide more Internet security for youngsters.

DT-APPE, developed by DrayTek, offers a mechanism to upgrade APPE signature automatically.

3. Setting confirmation page will be displayed as follows, please click Activate.

Vigor2762 Series User’s Guide

Page 55

Info The service will be activated and applied as the default rule configured in

Firewall>>General Setup.

4. Now, the web page will display the service that you have activated according to your

selection(s). The valid time for the free trial of these services is one month.

Vigor2762 Series User’s Guide

Page 56

I-8 Registering Vigor Router

You have finished the configuration of Quick Start Wizard and you can surf the Internet at any time. Now it is the time to register your Vigor router to MyVigor website for getting more service. Please follow the steps below to finish the router registration.

1 Please login the web configuration interface of Vigor router by typing “admin/admin”

as User Name / Password.

2 Click Support Area>>Production Registration from the home page.

3 A Login page will be shown on the screen. Please type the account and password that

you created previously. And click Login.

Vigor2762 Series User’s Guide

Page 57

Info If you haven’t an accessing account, please refer to section Creating an

Account for MyVigor to create your own one. Please read the articles on the Agreement regarding user rights carefully while creating a user account.

4 The following page will be displayed after you logging in MyVigor. When the following

page appears, please type in Nickname (for the router) and choose the right registration date from the popup calendar (it appears when you click on the box of Registration Date). Click Add.

5 When the following page appears, your router information has been added to the

database.

6 After clicking OK, you will see the following page. Your router has been registered to

myvigor website successfully.

Vigor2762 Series User’s Guide

Page 58

Part II Connectivity

It means wide area network. Public IP will be used in WAN.

It means local area network. Private IP will be used in LAN.

Local Area Network (LAN) is a group of subnets regulated and ruled by router. The design of network structure is related to what type of public IP addresses coming from your ISP.

When the data flow passing through, the Network Address Translation (NAT) function of the router will dedicate to translate public/private addresses, and the packets will be delivered to the correct host PC in the local area network.

DNS, LAN DNS, UPnP, IGMP, WOL …

Vigor2762 Series User’s Guide

Page 59

II-1 WAN

It allows users to access Internet.

Basics of Internet Protocol (IP) Network

IP means Internet Protocol. Every device in an IP-based Network including routers, print server, and host PCs, needs an IP address to identify its location on the network. To avoid address conflicts, IP addresses are publicly registered with the Network Information Centre (NIC). Having a unique IP address is mandatory for those devices participated in the public network but not in the private TCP/IP local area networks (LANs), such as host PCs under the management of a router since they do not need to be accessed by the public. Hence, the NIC has reserved certain addresses that will never be registered publicly. These are known as private IP addresses, and are listed in the following ranges:

From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255

What are Public IP Address and Private IP Address

As the router plays a role to manage and further protect its LAN, it interconnects groups of host PCs. Each of them has a private IP address assigned by the built-in DHCP server of the Vigor router. The router itself will also use the default private IP address: 192.168.1.1 to communicate with the local hosts. Meanwhile, Vigor router will communicate with other network devices through a public IP address. When the data flow passing through, the Network Address Translation (NAT) function of the router will dedicate to translate public/private addresses, and the packets will be delivered to the correct host PC in the local area network. Thus, all the host PCs can share a common Internet connection.

Get Your Public IP Address from ISP

In ADSL deployment, the PPP (Point to Point)-style authentication and authorization is required for bridging customer premises equipment (CPE). Point to Point Protocol over Ethernet (PPPoE) connects a network of hosts via an access device to a remote access concentrator or aggregation concentrator. This implementation provides users with significant ease of use. Meanwhile it provides access control, billing, and type of service according to user requirement.

When a router begins to connect to your ISP, a serial of discovery process will occur to ask for a connection. Then a session will be created. Your user ID and password is authenticated via PAP or CHAP with RADIUS authentication system. And your IP address, DNS server, and other related information will usually be assigned by your ISP.

Network Connection by 3G/4G USB Modem

For 3G/4G mobile communication through Access Point is popular more and more, Vigor2762 adds the function of 3G/4G network connection for such purpose. By connecting 3G/4G USB Modem to the USB port of Vigor2762, it can support LTE/HSDPA/UMTS/EDGE/GPRS/GSM and the future 3G/4G standard (HSUPA, etc). Vigor2762n with 3G/4G USB Modem allows you to receive 3G/4G signals at any place such as your car or certain location holding outdoor activity and share the bandwidth for using by more people. Users can use LAN ports on the router to access Internet. Also, they can access Internet via 802.11(a/b/g/n/ac) wireless standard, and enjoy the powerful firewall, bandwidth management, and VPN features of Vigor2762n series.

Vigor2762 Series User’s Guide

Page 60

After connecting into the router, 3G/4G USB Modem will be regarded as the WAN3/WAN4 port. However, the original WAN1 and WAN2 still can be used and Load-Balance can be done in the router. Besides, 3G/4G USB Modem in WAN3/WAN4 also can be used as backup device. Therefore, when WAN1 and WAN2 are not available, the router will use 3.5G for supporting automatically. The supported 3G/4G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information.

Vigor2762 Series User’s Guide

Page 61

Web User Interface

II-1-1 General Setup

This section will introduce some general settings of Internet and explain the connection modes for WAN1, WAN2 and WAN3/WAN4 in details.

This router supports multiple-WAN function. If any connection problem occurrs on one of the ISP connections, traffic will be guided and switched to the backup Internet connection until it resumes connectivity.

This webpage allows you to set general setup for WAN1, WAN2, WAN3 and WAN4 respectively. In default, WAN2 is disabled. If you want to enable it, simply click the WAN2 link and select Yes in the field of Enable.

Available settings are explained as follows:

Item Description

Index Click the WAN interface link under Index to access into the

WAN configuration page.

Enable V means such WAN interface is enabled and ready to be

used.

Physical Mode / Type Display the physical mode and physical type of such WAN

interface.

Active Mode Display whether such WAN interface is Active device or

backup device.

After finished the above settings, click OK to save the settings.

Vigor2762 Series User’s Guide

Page 62

II-1-1-1 WAN1 (ADSL/VDSL)

Vigor router will detect the physical line is connected by ADSL automatically. Therefore, this page allows you to configure settings for ADSL at one time. That is, it is not necessary for you to configure different profile settings for ADSL respectively.

Vigor2762 Series User’s Guide

Page 63

Available settings are explained as follows:

Item Description

Enable Choose Yes to invoke the settings for this WAN interface.

Choose No to disable the settings for this WAN interface.

Display Name Type the description for such interface.

Physical Mode Display the physical mode of such interface.

DSL Mode Specify the physical mode (VDSL or ADSL) for such router

manually.

DSL Modem Code Choose the correct DSL modem code for ensuring the

network connection.

If you have no idea about the selection, simply choose

Default or contact the dealer for assistance.

VLAN Tag insertion (ADSL/VDSL)

Such feature is offered to the user with the environment supporting IEEE_802.1ad. In which, service is used for outer tag; customer is used for inner tag.

Enable – Enable the function of VLAN with tag. The router will add specific VLAN number to all packets on

the WAN while sending them out. Please type the tag value and specify the priority for the

packets sending by WAN1.

Disable – Disable the function of VLAN with tag. Tag value – Type the value as the VLAN ID number. The

range is form 0 to 4095. Priority – Type the packet priority number for such VLAN.

The range is from 0 to 7.

Vigor2762 Series User’s Guide

Page 64

II-1-1-2 WAN2 (Ethernet)

Ethernet is the Physical Mode for WAN2.

Available settings are explained as follows:

Item Description

Enable Choose Yes to invoke the settings for this WAN interface.

Choose No to disable the settings for this WAN interface.

Display Name Type the description for such WAN interface.

Physical Mode Display the physical mode of such WAN interface.

Physical Type You can change the physical type for WAN1/WAN2/WAN3/

WAN4 or choose Auto negotiation for determined by the system.

Line Speed If you choose According to Line Speed as the Load

Balance Mode, please type the line speed for downloading

and uploading for such WAN interface. The unit is kbps.

VLAN Tag insertion Enable – Enable the function of VLAN with tag.

The router will add specific VLAN number to all packets on the WAN while sending them out.

Please type the tag value and specify the priority for the packets sending by WAN1.

Disable – Disable the function of VLAN with tag. Tag value – Type the value as the VLAN ID number. The

range is form 0 to 4095. Priority – Type the packet priority number for such VLAN.

The range is from 0 to 7.

Active Mode Choose Always On to make the WAN connection being

Vigor2762 Series User’s Guide

Page 65

activated always. If you choose Failover as the Active Mode, the option of

Active When will appear. Failover – Choose it to make the WAN connection as a

backup connection.

 WAN Failure – When the active WAN failed, such WAN

will be activated as the main network connection.

 Traffic Threshold – When the data traffic of active

WAN reaches the traffic threshold (specified here), the failover WAN will be enabled automatically to share the overloaded data traffic.

After finished the above settings, click OK to save the settings.

II-1-1-3 WAN3 / WAN4 (USB)

To use 3G/4G network connection through 3G/4G USB Modem, please configure WAN3 or WAN4 interface.

Available settings are explained as follows:

Item Description

Enable Choose Yes to invoke the settings for this WAN interface.

Choose No to disable the settings for this WAN interface.

Display Name Type the description for such WAN interface.

Physical Mode Display the physical mode of such WAN interface.

Line Speed If you choose According to Line Speed as the Load Balance

Mode, please type the line speed for downloading and

uploading for such WAN interface. The unit is kbps.

Active Mode Choose Always On to make the WAN connection being

activated always. If you choose Failover as the Active Mode, the option of

Active When will appear. Failover – Choose it to make the WAN connection as a

backup connection.

Vigor2762 Series User’s Guide

Page 66

Item Description

 WAN Failure – When the active WAN failed, such WAN

will be activated as the main network connection.

 Traffic Threshold – When the data traffic of active

WAN reaches the traffic threshold (specified here), the failover WAN will be enabled automatically to share the overloaded data traffic.

After finished the above settings, click OK to save the settings.

Vigor2762 Series User’s Guide

Page 67

II-1-2 Internet Access

For the router supports multi-WAN function, the users can set different WAN settings (for WAN1/WAN2/WAN3) for Internet Access. Due to different Physical Mode for WAN interface, the Access Mode for these connections also varies. Refer to the following figures.

And,

Available settings are explained as follows:

Item Description

Index Display the WAN interface.

Display Name It shows the name of the WAN1/WAN2/WAN3 that entered

in general setup.

Physical Mode It shows the physical connection for WAN1~2 (Ethernet)

/WAN3 (3G/4G USB Modem) according to the real network connection.

Access Mode Use the drop down list to choose a proper access mode. The

details page of that mode will be popped up. If not, click

Vigor2762 Series User’s Guide

Page 68

Details Page for accessing the page to configure the settings.

Details Page This button will open different web page (based on IPv4)

according to the access mode that you choose in WAN interface.

Note that Details Page will be changed slightly based on physical mode.

IPv6 This button will open different web page (based on Physical

Mode) to setup IPv6 Internet Access Mode for WAN interface.

If IPv6 service is active on this WAN interface, the color of “IPv6” will become green.

Advanced This button allows you to configure DHCP client options.

DHCP packets can be processed by adding option number and data information when such function is enabled and configured.

Enable – Check the box to enable the function of DHCP Option. Each DHCP option is composed by an option number with data. For example,

Option number:100 Data: abcd

When such function is enabled, the specified values for DHCP option will be seen in DHCP reply packets.

Interface – Specify the WAN interface(s) that will be overwritten by such function. WAN5 ~ WAN7 can be located under WAN>>Multi-PVC/VLAN.

Option Number – Type a number for such function. DataType – Choose the type (ASCII or Hex) for the data to

be stored. Data – Type the content of the data to be processed by the

function of DHCP option.

Info If you choose to configure option 61 here, the detailed settings in WAN>>Internet

Access will be overwritten.

Vigor2762 Series User’s Guide

Page 69

II-1-2-1 Details Page for PPPoE/PPPoA in WAN1 (Physical Mode: ADSL)

Available settings are explained as follows:

Item Description

Enable/Disable Click Enable for activating this function. If you click

Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

Modem Settings Set up the DSL parameters required by your ISP. These

settings configured here are specified for ADSL only. Multi-PVC channel - The selections displayed here are

determined by the page of WAN >> Multi-PVC/VLAN. Select

M-PVCs Channel means no selection will be chosen. VPI - Type in the value provided by ISP. VCI - Type in the value provided by ISP. Encapsulating Type - Drop down the list to choose the type

provided by ISP. Protocol - Drop down the list to choose the one (PPPoE or

PPPoA) provided by ISP. If you have already used Quick Start Wizard to set the

protocol, then it is not necessary for you to change any settings in this group.

Modulation –Default setting is Multimode. Choose the one that fits the requirement of your router.

Vigor2762 Series User’s Guide

Page 70

PPPoE Pass-through The router offers PPPoE dial-up connection. Besides, you

also can establish the PPPoE connection directly from local clients to your ISP via the Vigor router. When PPPoA protocol is selected, the PPPoE package transmitted by PC will be transformed into PPPoA package and sent to WAN server. Thus, the PC can access Internet through such direction.

For Wired LAN – If you check this box, PCs on the same network can use another set of PPPoE session (different with the Host PC) to access into Internet.

For Wireless LAN – It is available for n model. If you check this box, PCs on the same wireless network can use another set of PPPoE session (different with the Host PC) to access into Internet.

To have PPPoA Pass-through, please choose PPPoA protocol and check the box(es) here. The router will behave like a modem which only serves the PPPoE client on the LAN. That’s, the router will offer PPPoA dial-up connection.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 Ping Gateway IP – If you choose Ping Detect as

detection mode, you also can enable this setting to use current WAN gateway IP address for pinging.

With the IP address(es) pinging, Vigor router can check if the WAN connection is on or off.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific transmit path.

Click Detect to open the following dialog.

Vigor2762 Series User’s Guide

Page 71

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

size of MTU value. For example, the number specified in this field is “8”. The maximum MTU size is “1500”. After clicking the “detect” button, the system will calculate and get the suitable MTU value such as 1500, 1492, 1484 and etc., automatically.

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

ISP Access Setup Enter your allocated username, password and

authentication parameters according to the information provided by your ISP.

Service Name - Enter the description of the specific network service.

Username – Type in the username provided by ISP in this field.

Password – Type in the password provided by ISP in this field.

Separate Account for ADSL – In default, WAN1 supports VDSL2/ADSL and uses the same PPPoE account and password for connection. If required, you can configure another account and password for ADSL connection by checking this box. If it is checked, the system will ask you to type another group of account and password additionally.

PPP Authentication – Select PAP only or PAP or CHAP for PPP.

IP Address From ISP Usually ISP dynamically assigns IP address to you each time

you connect to it and request. In some case, your ISP provides service to always assign you the same IP address whenever you request. In this case, you can fill in this IP address in the Fixed IP field. Please contact your ISP before you want to use this function.

Fixed IP – Click Yes to use this function and type in a fixed IP address in the box of Fixed IP Address.

Default MAC Address – You can use Default MAC Address or specify another MAC address by typing on the boxes of MAC Address for the router.

Specify a MAC Address – Type the MAC address for the router manually.

Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set previously in Applications >> Schedule web page and you can use the number that you have set in that web page.

Vigor2762 Series User’s Guide

Page 72

II-1-2-2 Details Page for M

II-1-2-2 Details Page for Mpp

oA/Static or Dynamic IP in WAN1 (Physical Mode:

ADSL)

MPoA is a specification that enables ATM services to be integrated with existing LANs, which use either Ethernet, token-ring or TCP/IP protocols. The goal of MPoA is to allow different LANs to send packets to each other via an ATM backbone.

To use MPoA / Static or Dynamic IP as the accessing protocol of the Internet, select MPoA / Static or Dynamic IP from the WAN>>Internet Access >>WAN1 page. The following web page will appear.

Available settings are explained as follows:

Item Description

Enable/Disable Click Enable for activating this function. If you click

Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

Modem Settings Set up the DSL parameters required by your ISP. These

settings configured here are specified for ADSL only. Multi-PVC channel - The selections displayed here are

determined by the page of Internet Access >>Multi PVCs.

Select M-PVCs Channel means no selection will be chosen. Encapsulation - Drop down the list to choose the type

provided by ISP.

VPI - Type in the value provided by ISP. VCI - Type in the value provided by ISP. Modulation –Default setting is Multimode. Choose the one

that fits the requirement of your router.

Vigor2762 Series User’s Guide

Page 73

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

Mode – Choose ARP Detect or Ping Detect or Always On for the system to execute for WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 Ping Gateway IP – If you choose Ping Detect as

detection mode, you also can enable this setting to use current WAN gateway IP address for pinging. With the IP address(es) pinging, Vigor router can check if the WAN connection is on or off.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific transmit path.

Click Detect to open the following dialog.

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

RIP Protocol Routing Information Protocol is abbreviated as

RIP（RFC1058）specifying how routers exchange routing tables information. Click Enable RIP for activating this function.

Bridge Mode Enable Bridge Mode - If the function is enabled, the router

will work as a bridge modem.

WAN IP Network Settings This group allows you to obtain an IP address automatically

Vigor2762 Series User’s Guide

Page 74

and allows you type in IP address manually. Obtain an IP address automatically – Click this button to

obtain the IP address automatically.

 Router Name – Type in the router name provided

by ISP.

 Domain Name – Type in the domain name that

you have assigned.

DHCP Client Identifier for some ISP -

 Enable: Check the box to specify username and

password as the DHCP client identifier for some ISP.

 Username: Type a name as username. The

maximum length of the user name you can set is 63 characters.

 Password: Type a password. The maximum

length of the password you can set is 62 characters.

Specify an IP address – Click this radio button to specify some data.

 IP Address – Type in the private IP address.  Subnet Mask – Type in the subnet mask.  Gateway IP Address – Type in gateway IP

address.

Default MAC Address – Type in MAC address for the router. You can use Default MAC Address or specify another MAC address for your necessity.

Specify a MAC Address – Type in the MAC address for the router manually.

DNS Server IP Address Type in the primary IP address for the router. If necessary,

type in secondary IP address for necessity in the future.

After finishing all the settings here, please click OK to activate them.

Vigor2762 Series User’s Guide

Page 75

II-1-2-3 Details Page for PPPoE in Ethernet WAN

To choose PPPoE as the accessing protocol of the Internet, please select PPPoE from the WAN>>Internet Access >>WAN1 page. The following web page will be shown.

Available settings are explained as follows:

Item Description

Enable/Disable Click Enable for activating this function. If you click

Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

ISP Access Setup Enter your allocated username, password and

authentication parameters according to the information provided by your ISP.

Service Name (Optional) - Enter the description of the specific network service.

Username – Type in the username provided by ISP in this field.

The maximum length of the user name you can set is 63 characters.

Password – Type in the password provided by ISP in this field.

The maximum length of the password you can set is 62 characters.

Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and

Vigor2762 Series User’s Guide

Page 76

you can use the number that you have set in that web page.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 Ping Gateway IP – If you choose Ping Detect as

detection mode, you also can enable this setting to use current WAN gateway IP address for pinging. With the IP address(es) pinging, Vigor router can check if the WAN connection is on or off.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific transmit path.

Click Detect to open the following dialog.

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

TTL Change the TTL value – Enable or disable the TTL (Time to

Live) for a packet transmitted through Vigor router. Enable - TTL value will be reduced (-1) when it passess

through Vigor router. It will cause the client, accessing Internet through Vigor router, be blocked by certain ISP when TTL value becomes “0”.

Vigor2762 Series User’s Guide

Page 77

Disable – TTL value will not be reduced. Then, when a packet passes through Vigor router, it will not be cancelled. That is, the client who sends out the packet will not be blocked by ISP.

PPP/MP Setup PPP Authentication – Select PAP only or PAP or CHAP for

PPP. Idle Timeout – Set the timeout for breaking down the

Internet after passing through the time without any action.

IP Address Assignment Method (IPCP)

Usually ISP dynamically assigns IP address to you each time you connect to it and request. In some case, your ISP provides service to always assign you the same IP address whenever you request. In this case, you can fill in this IP address in the Fixed IP field. Please contact your ISP before you want to use this function.

Fixed IP – Click Yes to use this function and type in a fixed IP address in the box of Fixed IP Address.

Default MAC Address – You can use Default MAC Address or specify another MAC address by typing on the boxes of MAC Address for the router.

Specify a MAC Address – Type the MAC address for the router manually.

After finishing all the settings here, please click OK to activate them.

II-1-2-4 Details Page for Static or Dynamic IP in Ethernet WAN

For static IP mode, you usually receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address or many IP address to the WAN interface.

To use Static or Dynamic IP as the accessing protocol of the internet, please click the Static or Dynamic IP tab. The following web page will be shown.

Vigor2762 Series User’s Guide

Page 78

Available settings are explained as follows:

Item Description

Enable / Disable Click Enable for activating this function. If you click

Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

Keep WAN Connection Normally, this function is designed for Dynamic IP

environments because some ISPs will drop connections if there is no traffic within certain periods of time. Check

Enable PING to keep alive box to activate this function. PING to the IP - If you enable the PING function, please

specify the IP address for the system to PING it for keeping alive.

PING Interval - Enter the interval for the system to execute the PING operation.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 Ping Gateway IP – If you choose Ping Detect as

detection mode, you also can enable this setting to use current WAN gateway IP address for pinging. With the IP

Vigor2762 Series User’s Guide

Page 79

address(es) pinging, Vigor router can check if the WAN connection is on or off.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific transmit path.

Click Detect to open the following dialog.

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

RIP Protocol Routing Information Protocol is abbreviated as

RIP（RFC1058）specifying how routers exchange routing tables information. Click Enable RIP for activating this function.

TTL Change the TTL value – Enable or disable the TTL (Time to

Live) for a packet transmitted through Vigor router. Enable - TTL value will be reduced (-1) when it passess

through Vigor router. It will cause the client, accessing Internet through Vigor router, be blocked by certain ISP when TTL value becomes “0”.

Disable – TTL value will not be reduced. Then, when a packet passes through Vigor router, it will not be cancelled. That is, the client who sends out the packet will not be blocked by ISP.

WAN IP Network Settings This group allows you to obtain an IP address automatically

and allows you type in IP address manually. Obtain an IP address automatically – Click this button to

obtain the IP address automatically if you want to use Dynamic IP mode.

 Router Name: Type in the router name provided

Vigor2762 Series User’s Guide

Page 80

by ISP.

 Domain Name: Type in the domain name that

you have assigned.

DHCP Client Identifier for some ISP

 Enable: Check the box to specify username and

password as the DHCP client identifier for some ISP.

 Username: Type a name as username. The

maximum length of the user name you can set is 63 characters.

 Password: Type a password. The maximum

length of the password you can set is 62 characters.

Specify an IP address – Click this radio button to specify some data if you want to use Static IP mode.

 IP Address: Type the IP address.  Subnet Mask: Type the subnet mask.  Gateway IP Address: Type the gateway IP

address.

Default MAC Address: Click this radio button to use default MAC address for the router.

Specify a MAC Address: Some Cable service providers specify a specific MAC address for access authentication. In such cases you need to click the Specify a MAC Address and enter the MAC address in the MAC Address field.

DNS Server IP Address Type in the primary IP address for the router if you want to

use Static IP mode. If necessary, type in secondary IP address for necessity in the future.

After finishing all the settings here, please click OK to activate them.

Vigor2762 Series User’s Guide

Page 81

II-1-2-5 Details Page for PPTP/L2TP in Ethernet WAN

To use PPTP/L2TP as the accessing protocol of the internet, please click the PPTP/L2TP tab. The following web page will be shown.

Available settings are explained as follows:

Item Description

PPTP/L2TP Enable PPTP- Click this radio button to enable a PPTP

client to establish a tunnel to a DSL modem on the WAN interface.

Enable L2TP - Click this radio button to enable a L2TP client to establish a tunnel to a DSL modem on the WAN interface.

Disable – Click this radio button to close the connection through PPTP or L2TP.

Server Address - Specify the IP address of the PPTP/L2TP server if you enable PPTP/L2TP client mode.

Specify Gateway IP Address – Specify the gateway IP address for DHCP server.

ISP Access Setup Username -Type in the username provided by ISP in this

field. The maximum length of the user name you can set is 63 characters.

Password -Type in the password provided by ISP in this field. The maximum length of the password you can set is 62 characters.

Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific

Vigor2762 Series User’s Guide

Page 82

transmit path. Click Detect to open the following dialog.

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

PPP Setup PPP Authentication - Select PAP only or PAP or CHAP for

PPP. Idle Timeout - Set the timeout for breaking down the

Internet after passing through the time without any action.

IP Address Assignment Method(IPCP)

Fixed IP - Usually ISP dynamically assigns IP address to you

each time you connect to it and request. In some case, your ISP provides service to always assign you the same IP address whenever you request. In this case, you can fill in this IP address in the Fixed IP field. Please contact your ISP before you want to use this function. Click Yes to use this function and type in a fixed IP address in the box.

Fixed IP Address -Type a fixed IP address.

WAN IP Network Settings Obtain an IP address automatically – Click this button to

obtain the IP address automatically. Specify an IP address – Click this radio button to specify

some data.

 IP Address – Type the IP address.  Subnet Mask – Type the subnet mask.

After finishing all the settings here, please click OK to activate them.

II-1-2-6 Details Page for 3G/4G USB Modem (PPP mode) in USB WAN

To use 3G/4G USB Modem (PPP mode) as the accessing protocol of the internet, please choose Internet Access from WAN menu. Then, select 3G/4G USB Modem (PPP mode) for WAN5. The following web page will be shown.

Vigor2762 Series User’s Guide

Page 83

Available settings are explained as follows:

Item Description

Modem Support List It lists all of the modems supported by such router.

3G /4G USB Modem (PPP mode)

Click Enable for activating this function. If you click Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

SIM PIN code Type PIN code of the SIM card that will be used to access

Internet. The maximum length of the PIN code you can set is 15

characters.

Modem Initial String Such value is used to initialize USB modem. Please use the

default value. If you have any question, please contact to

Vigor2762 Series User’s Guide

Page 84

your ISP. The maximum length of the string you can set is 47

characters.

APN Name APN means Access Point Name which is provided and

required by some ISPs. Type the name and click Apply. The maximum length of the name you can set is 43

characters.

Modem Initial String2 The initial string 1 is shared with APN.

In some cases, user may need another initial AT command to restrict 3G band or do any special settings.

The maximum length of the string you can set is 47 characters.

Modem Dial String Such value is used to dial through USB mode. Please use the

default value. If you have any question, please contact to your ISP.

The maximum length of the string you can set is 31 characters.

Service Name Enter the description of the specific network service.

PPP Username Type the PPP username (optional). The maximum length of

the name you can set is 63 characters.

PPP Password Type the PPP password (optional). The maximum length of

the password you can set is 62 characters.

PPP Authentication Select PAP only or PAP or CHAP for PPP.

Index (1-15) in Schedule Setup

You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

After finishing all the settings here, please click OK to activate them.

Vigor2762 Series User’s Guide

Page 85

II-1-2-7 Details Page for 3G/4G USB Modem (DHCP mode) in USB WAN

To use 3G/4G USB Modem (DHCP mode) as the accessing protocol of the internet, please choose Internet Access from WAN menu. Then, select 3G/4G USB Modem (DHCP mode) for WAN3/WAN4. The following web page will be shown.

Available settings are explained as follows:

Item Description

Modem Support List It lists all of the modems supported by such router.

3G/4G USB Modem (DHCP mode)

Click Enable for activating this function. If you click Disable, this function will be closed and all the settings that

you adjusted in this page will be invalid.

SIM PIN code Type PIN code of the SIM card that will be used to access

Internet. The maximum length of the PIN code you can set is 19

characters.

Network Mode Force Vigor router to connect Internet with the mode

specified here. If you choose 4G/3G/2G as network mode,

Vigor2762 Series User’s Guide

Page 86

Item Description

the router will choose a suitable one according to the actual wireless signal automatically.

APN Name APN means Access Point Name which is provided and

required by some ISPs. Type the name and click Apply. The maximum length of the name you can set is 47

characters.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect.

Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.

 Primary/Secondary Ping IP – If you choose Ping Detect

as detection mode, you have to type Primary or Secondary IP address in this field for pinging.

 Ping Gateway IP – If you choose Ping Detect as

detection mode, you also can enable this setting to use current WAN gateway IP address for pinging. With the IP address(es) pinging, Vigor router can check if the WAN connection is on or off.

 TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to

execute the PING operation.

 Ping Retry – Type the number of times that the system is

allowed to execute the PING operation before WAN disconnection is judged.

MTU It means Max Transmit Unit for packet.

Path MTU Discovery – It is used to detect the maximum

MTU size of a packet not to be segmented in specific transmit path.

Click Detect to open the following dialog.

 Path MTU to – Type the IP address as the specific

transmit path.

 MTU reduce size by – It determines the decreasing

 Detect – Click it to detect a suitable MTU value  Accept – After clicking it, the detected value will be

displayed in the field of MTU.

Vigor2762 Series User’s Guide

Page 87

Item Description

Authentication Select PAP only or PAP or CHAP for PPP authentication.

Username – Type the username for authentication

(optional). Password – Type the password for authentication (optional).

After finishing all the settings here, please click OK to activate them.

II-1-2-8 Details Page for IPv6

II-1-2-8 Details Page for IPv6 ––

Offline in WAN1/WAN2/WAN3

When Offline is selected, the IPv6 connection will be disabled.

II-1-2-9 Details Page for IPv6

II-1-2-9 Details Page for IPv6 ––

PPP in WAN1/WAN2

During the procedure of IPv4 PPPoE connection, we can get the IPv6 Link Local Address between the gateway and Vigor router through IPv6CP. Later, use DHCPv6 or accept RA to acquire the IPv6 prefix address (such as: 2001:B010:7300:200::/64) offered by the ISP. In addition, PCs under LAN also can have the public IPv6 address for Internet access by means of the generated prefix.

No need to type any other information for PPP mode.

Available settings are explained as follows:

Item Description

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect for the system to execute for WAN detection. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

Vigor2762 Series User’s Guide

Page 88

Item Description

detection mode, you have to type TTL value.

RIPng Protocol RIPng (RIP next generation) offers the same functions and

benefits as IPv4 RIP v2.

Below shows an example for successful IPv6 connection based on PPP mode.

Info At present, the IPv6 prefix can be acquired via the PPPoE mode connection which

is available for the areas such as Taiwan (hinet), the Netherlands, Australia and UK.

II-1-2-10 Details Page for IPv6

II-1-2-10 Details Page for IPv6 ––

TSPC in WAN1/WAN2/WAN3

Tunnel setup protocol client (TSPC) is an application which could help you to connect to IPv6 network easily.

Please make sure your IPv4 WAN connection is OK and apply one free account from hexago (http://gogonet.gogo6.com/page/freenet6-account ) before you try to use TSPC for network connection. TSPC would connect to tunnel broker and requests a tunnel according to the specifications inside the configuration file. It gets a public IPv6 IP address and an IPv6 prefix from the tunnel broker and then monitors the state of the tunnel in background.

After getting the IPv6 prefix and starting router advertisement daemon (RADVD), the PC behind this router can directly connect to IPv6 the Internet.

Vigor2762 Series User’s Guide

Page 89

Available settings are explained as follows:

Item Description

Username Type the name obtained from the broker. It is suggested for

you to apply another username and password for

http://gogonet.gogo6.com/page/freenet6-account.

The maximum length of the name you can set is 63 characters.

Password Type the password assigned with the user name.

The maximum length of the name you can set is 19 characters.

Tunnel Broker Type the address for the tunnel broker IP, FQDN or an

optional port number.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect for the system to execute for WAN detection. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

detection mode, you have to type TTL value.

After finished the above settings, click OK to save the settings.

Vigor2762 Series User’s Guide

Page 90

II-1-2-11 Details Page for IPv6

II-1-2-11 Details Page for IPv6 ––

AICCU in WAN1/WAN2/WAN3

Available settings are explained as follows:

Item Description

Always On Check this box to keep the network connection always.

Username Type the name obtained from the broker. Please apply new

account at http://www.sixxs.net/. It is suggested for you to apply another username and password.

The maximum length of the name you can set is 19 characters.

Password Type the password assigned with the user name.

The maximum length of the password you can set is 19 characters.

Tunnel Broker It means a server of AICCU. The server can provide IPv6

tunnels to sites or end users over IPv4. Type the address for the tunnel broker IP, FQDN or an

optional port number.

Tunnel ID One user account may have several tunnels. And, each

tunnel shall have one specified tunnel ID (e.g., T115394). Type the ID offered by Tunnel Broker.

Subnet Prefix Type the subnet prefix address obtained from service

provider. The maximum length of the prefix you can set is 128

characters.

WAN Connection Such function allows you to verify whether network

Vigor2762 Series User’s Guide

Page 91

Item Description

Detection connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect for the system to

execute for WAN detection.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

detection mode, you have to type TTL value.

After finished the above settings, click OK to save the settings.

Vigor2762 Series User’s Guide

Page 92

II-1-2-12 Details Page for IPv6

II-1-2-12 Details Page for IPv6 ––

DHCPv6 Client in WAN1/WAN2

DHCPv6 client mode would use DHCPv6 protocol to obtain IPv6 address from server.

Available settings are explained as follows:

Item Description

IAID Type a number as IAID.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through NS Detect or Ping Detect.

Mode – Choose Always On, Ping Detect or NS Detect for the system to execute for WAN detection. With NS Detect mode, the system will check if network connection is established or not, like IPv4 ARP Detect. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

detection mode, you have to type TTL value.

RIPng Protocol RIPng (RIP next generation) offers the same functions and

benefits as IPv4 RIP v2.

Bridge Mode Enable Bridge Mode - If the function is enabled, the router

will work as a bridge modem. Enable Firewall – It is available when Bridge Mode is

enabled. When both Bridge Mode and Firewall check boxes

Vigor2762 Series User’s Guide

Page 93

Item Description

are enabled, the settings configured (user profiles) under User Management will be ignored. And all of the filter rules defined and enabled in Firewall menu will be activated.

Bridge Subnet – Make a bridge between the selected LAN subnet and such WAN interface.

After finished the above settings, click OK to save the settings.

II-1-2-13 Details Page for IPv6

II-1-2-13 Details Page for IPv6 ––

Static

IPv6 in in WAN1/WAN2

This type allows you to setup static IPv6 address for WAN interface.

Vigor2762 Series User’s Guide

Page 94

Available settings are explained as follows:

Item Description

Static IPv6 Address Configuration

IPv6 Address – Type the IPv6 Static IP Address. Prefix Length – Type the fixed value for prefix length. Add – Click it to add a new entry. Update – Click it to modify an existed entry. Delete – Click it to remove an existed entry.

Current IPv6 Address Table

Display current interface IPv6 address.

Static IPv6 Gateway Configuration

IPv6 Gateway Address - Type your IPv6 gateway address

here.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect or NS Detect for the system to execute for WAN detection. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

detection mode, you have to type TTL value.

RIPng Protocol RIPng (RIP next generation) offers the same functions and

benefits as IPv4 RIP v2.

Bridge Mode Enable Bridge Mode - If the function is enabled, the router

will work as a bridge modem. Enable Firewall – It is available when Bridge Mode is

enabled. When both Bridge Mode and Firewall check boxes are enabled, the settings configured (user profiles) under User Management will be ignored. And all of the filter rules defined and enabled in Firewall menu will be activated.

Bridge Subnet – Make a bridge between the selected LAN subnet and such WAN interface.

After finished the above settings, click OK to save the settings.

Vigor2762 Series User’s Guide

Page 95

II-1-2-14 Details Page for IPv6

II-1-2-14 Details Page for IPv6 ––

6in4 Static Tunnel in WAN1 / WAN2

This type allows you to setup 6in4 Static Tunnel for WAN interface.

Such mode allows the router to access IPv6 network through IPv4 network.

However, 6in4 offers a prefix outside of 2002::0/16. So, you can use a fixed endpoint rather than anycast endpoint. The mode has more reliability.

Available settings are explained as follows:

Item Description

Remote Endpoint IPv4 Address

Type the static IPv4 address for the remote server.

6in4 IPv6 Address Type the static IPv6 address for IPv4 tunnel with the value

for prefix length.

LAN Routed Prefix Type the static IPv6 address for LAN routing with the value

for prefix length.

Tunnel TTL Type the number for the data lifetime in tunnel.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect for the system to execute for WAN detection. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

 TTL (Time to Live) –If you choose Ping Detect as

Vigor2762 Series User’s Guide

Page 96

Item Description

detection mode, you have to type TTL value.

After finished the above settings, click OK to save the settings.

Below shows an example for successful IPv6 connection based on 6in4 Static Tunnel mode.

Vigor2762 Series User’s Guide

Page 97

II-1-2-15 Details Page for IPv6

II-1-2-15 Details Page for IPv6 ––

6rd in WAN1 / WAN2

This type allows you to setup 6rd for WAN interface.

Available settings are explained as follows:

Item Description

6rd Mode Auto 6rd – Retrieve 6rd prefix automatically from 6rd

service provider. The IPv4 WAN must be set as "DHCP".

Static 6rd - Set 6rd options manually.

IPv4 Border Relay Type the IPv4 addresses of the 6rd Border Relay for a given

6rd domain.

IPv4 Mask Length Type a number of high-order bits that are identical across

all CE IPv4 addresses within a given 6rd domain. It may be any value between 0 and 32.

6rd Prefix Type the 6rd IPv6 address.

6rd Prefix Length Type the IPv6 prefix length for the 6rd IPv6 prefix in

number of bits.

WAN Connection Detection

Such function allows you to verify whether network connection is alive or not through Ping Detect.

Mode – Choose Always On or Ping Detect for the system to execute for WAN detection. Always On means no detection will be executed. The network connection will be on always.

 Ping IP/Hostname – If you choose Ping Detect as

detection mode, you have to type IP address in this field for pinging.

Vigor2762 Series User’s Guide

Page 98

Item Description

 TTL (Time to Live) –If you choose Ping Detect as

detection mode, you have to type TTL value.

After finished the above settings, click OK to save the settings.

Below shows an example for successful IPv6 connection based on 6rd mode.

Vigor2762 Series User’s Guide

Page 99

II-1-3 Multi-PVC/VLAN

This router allows you to create multi-PVC for different data transferring for using. Simply go to WAN and select Multi-PVC/VLAN page.

General

The system allows you to set up to eight channels which are ready for choosing as the first PVC line that will be used as multi-PVC.

Available settings are explained as follows:

Item Description

Channel Display the number of each channel.

Channels 1 and 2 are used by the Internet Access web user interface and can not be configured here.

Channels 4 ~ 10 are configurable.

Enable Display whether the settings in this channel are enabled

(Yes) or not (No).

WAN Type Displays the physical medium that the channel will use.

VPI/VCI Display the value for VPI and VCI.

VLAN Tag Displays the VLAN tag value that will be used for the

packets traveling on this channel.

Port-based Bridge The network traffic flowing on each channel will be

identified by the system via their VLAN Tags. Channels using the same WAN type may not configure the same VLAN tag value.

Enable - Check this box to enable the port-based bridge function on this channel.

P1 ~ P4 – Check the box(es) to build bridge connection on LAN.

Vigor2762 Series User’s Guide

Page 100

Click any index (7~10) to get the following web page:

Available settings are explained as follows:

Item Description

Multi-VLAN Channel 7~10 Enable – Click it to enable the configuration of this channel.

Disable –Click it to disable the configuration of this channel.

WAN Type The connections and interfaces created in every channel

may select a specific WAN type to be built upon. In the Multi-VLAN application, only the Ethernet WAN type is available. The user will be able to select the physical WAN interface the channel shall use here.

General Settings VPI - Type in the value provided by your ISP.

VCI - Type in the value provided by your ISP. Protocol - Select a proper protocol for this channel. Encapsulation - Choose a proper type for this channel. The

types will be different according to the protocol setting that you choose.

Add VLAN Header – Check the box to enable the following two options.

VLAN Tag – Type the value as the VLAN ID number. Valid settings are in the range from 1 to 4095. The network traffic flowing on each channel will be identified by the system via their VLAN Tags. Channels using the same WAN type may not configure the same VLAN tag value.

Priority – Choose the number to determine the packet priority for such VLAN. The range is from 0 to 7.

Bridge mode Enable – Click it to enable Bridge mode for such channel.

Physical Members – Group the physical ports by checking

the corresponding check box(es) for applying the bridge

Vigor2762 Series User’s Guide