Page 1
Page 2
Vigor2760 Series User’s Guide
ii
Page 3
Vigor2760 Series User’s Guide
iii
Vigor2760 Series
VDSL2 Security Firewall
User’s Guide
Version: 1.6
Firmware Version: V3.8.2.1
(For future update, please visit DrayTek web site)
Date: January 11, 2016
Page 4
Vigor2760 Series User’s Guide
iv
Intellectual Property Rights (IPR) Information
Copyrights
© All rights reserved. This publication contains information that is protected by
copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without written permission from the copyright
holders.
Trademarks
The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7 and Explorer are
trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Safety Instructions and Approval
Safety
Instructions
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
The router should be used in a sheltered area, within a temperature range of +5 to
+40 Celsius.
Do not expose the router to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock
hazards.
Keep the package out of reach of children.
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free from any
defects in workmanship or materials for a period of two (2) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it serves
as proof of date of purchase. During the warranty period, and upon proof of purchase,
should the product have indications of failure due to faulty workmanship and/or
materials, we will, at our discretion, repair or replace the defective products or
components, without charge for either parts or labor, to whatever extent we deem
necessary tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and
will be offered solely at our discretion. This warranty will not apply if the product is
modified, misused, tampered with, dam aged by an act of God, or subjected to abnormal
working conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the product will
not be covered by the warranty. We reserve the right to revi se the m anual and onli ne
documentation and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.DrayTek.com.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be regularly
upgraded. Please consult the DrayTek web site for more information on newest
firmware, tools and documents.
http://www.DrayTek.com
Page 5
Vigor2760 Series User’s Guide
v
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, Hukou Township, Hsinchu Industrial Park, Hsinchu County, Taiwan 303
Product: Vigor2760 Series Router
DrayTek Corp. declares that Vigor2760 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC and RoH S 201 1/65/EU
.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by
complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the
requirements set forth in EN60950-1.
This product is designed for the DSL and 2.4GHz WLAN network throughout the EC region. Please see the user
manual for the applicable networks on your product.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or televisio n recept i on , whi ch can be determined by turning the equipment of f and
on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must
be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Caution
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
The antenna/transmitter should be kept at least 20 cm away from human body.
DrayTek Vigor2760 series VDSL2/ADSL2+ routers are compliant with 47 C.F.R. Part 68.
Page 6
Vigor2760 Series User’s Guide
vi
IC Regulatory Information
Product: Vigor2760Vn, Vigor2760n
IC : 20803-V2760
Canadian Representative:
Company Name: Network Systems Solutions Canada Inc.
Company Address: 56 Rory Road, North York, ON, M6L 3G1
Company Telephone: 1-647-930-9285
This radio transmitter (IC:20803-V2760) has been approved by Industry Canada to operate with the antenna types listed below
with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum
gain indicated for that type, are strictly prohibited for use with this device.
Dipole antenna, maximum permissible gain: 2.1 dBi
Le présent émetteur radio (IC:20803-V2760) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Dipole antenne, maximal admissible gain: 2.1 dBi
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices subject only to the requirement that
the sum of the RENs of all the devices not exceed five.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement
économique Canada.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de dispositifs qui peuvent être raccordés à
une interface téléphonique. La terminaison d'une interface peut consister en une combinaison quelconque de dispositifs, à la
seule condition que la somme des IES de tous les dispositifs n'excède pas cinq.
Product: Vigor2760
IC: 20803-2760
Canadian Representative:
Company Name: Network Systems Solutions Canada Inc.
Company Address: 56 Rory Road, North York, ON, M6L 3G1
Company Telephone: 1-647-930-9285
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices subject only to the requirement that
the sum of the RENs of all the devices not exceed five.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement
économique Canada.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de dispositifs qui peuvent être raccordés à
une interface téléphonique. La terminaison d'une interface peut consister en une combinaison quelconque de dispositifs, à la
seule condition que la somme des IES de tous les dispositifs n'excède pas cinq.
Page 7
Vigor2760 Series User’s Guide
vii
More update, please visit www.draytek.com.
Page 8
Vigor2760 Series User’s Guide
viii
TTaabbllee ooff CCoonntteennttss
Introduction...................................................................................................1
1.1 Features.......................................................................................................................... 2
1.2 Package and Content.............................................................................................................. 4
1.3 LED Indicators and Connectors.............................................................................................. 5
1.3.1 For Vigor2760................................................................................................................... 5
1.3.2 For Vigor2760n................................................................................................................. 7
1.3.3 For Vigor2760Vn............................................................................................................... 9
1.4 Hardware Installation .............................................................................................................11
1.5 Printer Installation ................................................................................................................. 12
1.6 Accessing Web Page............................................................................................................ 20
1.7 Changing Password.............................................................................................................. 21
1.8 Introducing Dashboard.......................................................................................................... 22
1.8.1 Virtual Panel ................................................................................................................... 23
1.8.2 Name with a Link............................................................................................................ 23
1.8.3 Quick Access for Common Used Menu.......................................................................... 24
1.8.4 GUI Map ......................................................................................................................... 25
1.8.5 Web Console.................................................................................................................. 26
1.8.6 Config Backup ................................................................................................................ 27
1.8.7 Logout............................................................................................................................. 27
1.9 Online Status......................................................................................................................... 28
1.9.1 Physical Connection.......................................................................................................28
1.9.2 Virtual WAN.................................................................................................................... 30
1.10 Saving Configuration........................................................................................................... 31
Quick Setup.................................................................................................33
2.1 Quick Start Wizard................................................................................................................ 33
2.1.1 For WAN1 (ADSL/VDSL2).............................................................................................. 35
2.1.2 For WAN2 (Ethernet)...................................................................................................... 41
2.1.3 For WAN3 (USB)............................................................................................................50
2.2 Service Activation Wizard...................................................................................................... 52
2.3 VPN Client Wizard ................................................................................................................ 55
2.4 VPN Server Wizard............................................................................................................... 61
2.5 Wireless Wizard.................................................................................................................... 66
2.6 VoIP Wizard........................................................................................................................... 69
2.7 Registering Vigor Router....................................................................................................... 71
Page 9
Vigor2760 Series User’s Guide
ix
Advanced Configuration............................................................................75
3.1 WAN...................................................................................................................................... 75
3.1.1 Basics of Internet Protocol (IP) Network......................................................................... 75
3.1.2 General Setup................................................................................................................. 77
3.1.3 Internet Access............................................................................................................... 82
3.1.4 Multi-PVC/VLAN........................................................................................................... 119
3.2 LAN ..................................................................................................................................... 125
3.2.1 Basics of LAN ............................................................................................................... 125
3.2.2 General Setup............................................................................................................... 128
3.2.3 Static Route.................................................................................................................. 140
3.2.4 VLAN............................................................................................................................. 145
3.2.5 Bind IP to MAC............................................................................................................. 148
3.2.6 LAN Port Mirror............................................................................................................. 150
3.2.7 Web Portal Setup.......................................................................................................... 151
3.3 Route Policy........................................................................................................................ 152
3.3.1 General Setup............................................................................................................... 152
3.3.2 Diagnose....................................................................................................................... 159
3.4 NA T..................................................................................................................................... 162
3.4.1 Port Redirection............................................................................................................ 162
3.4.2 DMZ Host...................................................................................................................... 166
3.4.3 Open Ports.................................................................................................................... 169
3.4.4 Port Triggering.............................................................................................................. 171
3.5 Firewall................................................................................................................................ 174
3.5.1 Basics for Firewall......................................................................................................... 174
3.5.2 General Setup............................................................................................................... 176
3.5.3 Filter Setup ................................................................................................................... 181
3.5.4 DoS Defense ................................................................................................................ 189
3.6 Objects Settings.................................................................................................................. 193
3.6.1 IP Object....................................................................................................................... 193
3.6.2 IP Group ....................................................................................................................... 196
3.6.3 IPv6 Object................................................................................................................... 198
3.6.4 IPv6 Group.................................................................................................................... 200
3.6.5 Service Type Object ..................................................................................................... 201
3.6.6 Service Type Group...................................................................................................... 203
3.6.7 Keyword Object ............................................................................................................205
3.6.8 Keyword Group............................................................................................................. 207
3.6.9 File Extension Object.................................................................................................... 208
3.6.10 SMS/Mail Service Object............................................................................................ 210
3.6.11 Notification Object....................................................................................................... 215
3.7 CSM Profile.........................................................................................................................217
3.7.1 APP Enforcement Profile.............................................................................................. 218
3.7.2 APPE Signature Upgrade............................................................................................. 221
3.7.3 URL Content Filter Profile............................................................................................. 222
3.7.4 Web Content Filter Profile............................................................................................. 226
3.7.5 DNS Filter Profile.......................................................................................................... 230
3.7.6 APPE Support List........................................................................................................ 231
3.8 Bandwidth Management ..................................................................................................... 232
3.8.1 Sessions Limit............................................................................................................... 232
Page 10
Vigor2760 Series User’s Guide
x
3.8.2 Bandwidth Limit ............................................................................................................ 234
3.8.3 Quality of Service.......................................................................................................... 236
3.8.4 APP QoS ...................................................................................................................... 245
3.9 Applications......................................................................................................................... 247
3.9.1 Dynamic DNS............................................................................................................... 247
3.9.2 LAN DNS / DNS Forwarding ........................................................................................ 250
3.9.3 Schedule....................................................................................................................... 253
3.9.4 RADIUS........................................................................................................................ 256
3.9.5 Active Directory/LDAP.................................................................................................. 257
3.9.6 UPnP............................................................................................................................. 259
3.9.7 IGMP............................................................................................................................. 261
3.9.8 Wake on LAN................................................................................................................ 262
3.9.9 SMS / Mail Alert Service............................................................................................... 263
3.9.10 Bonjour ....................................................................................................................... 265
3.10 VPN and Remote Access.................................................................................................. 268
3.10.1 Remote Access Control.............................................................................................. 268
3.10.2 PPP General Setup .................................................................................................... 269
3.10.3 IPsec General Setup................................................................................................... 270
3.10.4 IPsec Peer Identity...................................................................................................... 272
3.10.5 Remote Dial-in User ................................................................................................... 274
3.10.6 LAN to LAN................................................................................................................. 277
3.10.7 Connection Management ........................................................................................... 287
3.11 Certificate Management.................................................................................................... 288
3.11.1 Local Certificate.......................................................................................................... 288
3.11.2 Trusted CA Certificate ................................................................................................ 291
3.11.3 Certificate Backup....................................................................................................... 293
3.12 VoIP................................................................................................................................... 294
3.12.1 General Setting........................................................................................................... 296
3.12.1 SIP Accounts.............................................................................................................. 298
3.12.2 DialPlan ...................................................................................................................... 302
3.12.3 Phone Settings ........................................................................................................... 311
3.12.4 Status.......................................................................................................................... 315
3.13 Wireless LAN .................................................................................................................... 317
3.13.1 Basic Concepts........................................................................................................... 317
3.13.2 General Setup............................................................................................................. 319
3.13.3 Security....................................................................................................................... 320
3.13.4 Access Control............................................................................................................ 323
3.13.5 WPS............................................................................................................................ 324
3.13.6 WDS............................................................................................................................ 327
3.13.7 Advanced Setting........................................................................................................ 330
3.13.8 Station Control............................................................................................................ 333
3.13.9 Bandwidth Management............................................................................................. 334
3.13.10 AP Discovery............................................................................................................ 335
3.13.11 Station List................................................................................................................ 336
3.14 SSL VPN........................................................................................................................... 337
3.14.1 General Setup............................................................................................................. 337
3.14.2 SSL Web Proxy .......................................................................................................... 338
3.14.3 SSL Application .......................................................................................................... 339
3.14.4 User Account.............................................................................................................. 341
3.14.5 User Group................................................................................................................. 345
3.14.6 Online User Status...................................................................................................... 347
3.15 USB Application................................................................................................................ 348
3.15.1 USB General Settings................................................................................................. 348
Page 11
Vigor2760 Series User’s Guide
xi
3.15.2 USB User Management.............................................................................................. 349
3.15.3 File Explorer................................................................................................................ 351
3.15.4 USB Device Status..................................................................................................... 352
3.15.5 Temperature Sensor................................................................................................... 353
3.15.6 Modem Support List.................................................................................................... 355
3.16 System Maintenance......................................................................................................... 356
3.16.1 System Status............................................................................................................. 356
3.16.2 TR-069........................................................................................................................ 358
3.16.3 Administrator Password.............................................................................................. 359
3.16.4 User Password ........................................................................................................... 360
3.16.5 Login Page Greeting................................................................................................... 362
3.16.6 Configuration Backup ................................................................................................. 364
3.16.7 Syslog/Mail Alert......................................................................................................... 366
3.16.8 Time and Date............................................................................................................ 369
3.16.9 SNMP.......................................................................................................................... 370
3.16.10 Management............................................................................................................. 372
3.16.11 Reboot System......................................................................................................... 376
3.16.12 Firmware Upgrade.................................................................................................... 377
3.16.13 DSL Firmware Upgrade............................................................................................ 378
3.16.14 Activation.................................................................................................................. 378
3.17 Diagnostics........................................................................................................................ 379
3.17.1 Dial-out Triggering...................................................................................................... 380
3.17.2 Routing Table ............................................................................................................. 381
3.17.3 ARP Cache Table....................................................................................................... 382
3.17.4 IPv6 Neighbour Table................................................................................................. 382
3.17.5 DHCP Table................................................................................................................ 383
3.17.6 NAT Sessions Table................................................................................................... 384
3.17.7 Ping Diagnosis............................................................................................................ 385
3.17.8 Data Flow Monitor....................................................................................................... 386
3.17.9 Traffic Graph............................................................................................................... 388
3.17.10 Trace Route.............................................................................................................. 389
3.17.11 Syslog Explorer......................................................................................................... 390
3.17.12 IPv6 TSPC Status..................................................................................................... 392
Tutorials and Applications....................................................................... 393
4.1 How to configure settings for IPv6 Service in Vigor2760.................................................... 393
4.2 How can I get the files from USB storage device connecting to Vigor router?................... 405
4.3 How to Build a LAN-to-LAN VPN Between Remote Office and Headquarter via IPsec Tunnel
(Main Mode).............................................................................................................................. 407
4.4 How to Optimize the Bandwidth through QoS Technology..................................................411
4.5 QoS Setting Example.......................................................................................................... 415
4.6 How to Send a Notification to Specified Phone Number via SMS Service in WAN
Disconnection............................................................................................................................ 420
4.7 How to Create an Account for MyVigor............................................................................... 424
4.7.1 Create an Account via Vigor Router............................................................................. 424
4.7.2 Create an Account via MyVigor Web Site .................................................................... 428
4.8 How to Setup Address Mapping.......................................................................................... 432
4.9 How to Configure Certain Computers Accessing to Internet.............................................. 434
Page 12
Vigor2760 Series User’s Guide
xii
4.10 How to Block Facebook Service Accessed by the Users via Web Content Filter / URL
Content Filter............................................................................................................................. 438
Trouble Shooting......................................................................................443
5.1 Checking If the Hardware Status Is OK or Not....................................................................443
5.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ................. 444
5.3 Pinging the Router from Y our Computer............................................................................. 447
5.4 Checking If the ISP Settings are OK or Not........................................................................ 448
5.5 Problems for 3G Network Connection ................................................................................ 448
5.6 Backing to Factory Default Setting If Necessary ................................................................ 449
5.7 Contacting DrayTek............................................................................................................. 450
Telnet Command Reference..........................................................................................451
Accessing Telnet of Vigor2760.................................................................................................. 451
Telnet Command: adsl bridge................................................................................................ 454
Telnet Command: adsl idle.................................................................................................... 455
Telnet Command: adsl drivemode......................................................................................... 455
Telnet Command: adsl reboot ............................................................................................... 455
Telnet Command: adsl oamlb................................................................................................ 456
Telnet Command: adsl vcilimit............................................................................................... 456
Telnet Command: adsl annex................................................................................................ 457
Telnet Command: adsl automode ......................................................................................... 457
Telnet Command: adsl optn................................................................................................... 457
Telnet Command: adsl savecfg............................................................................................. 458
Telnet Command: adsl vendorid............................................................................................ 458
Telnet Command: adsl atm.................................................................................................... 458
Telnet Command: adsl pvcbinding........................................................................................ 459
Telnet Command: adsl snr..................................................................................................... 460
Telnet Command: vdsl status................................................................................................ 460
Example Telnet Command: vdsl idle..................................................................................... 460
Telnet Command: vdsl drivermode........................................................................................ 461
Telnet Command: vdsl reboot................................................................................................ 461
Telnet Command: vdsl annex................................................................................................ 461
Telnet Command: vdsl showbins........................................................................................... 462
Telnet Command: vdsl optn................................................................................................... 462
Telnet Command: vdsl savecfg ............................................................................................. 463
Telnet Command: vdsl vendorid............................................................................................ 463
Telnet Command: vdsl snr..................................................................................................... 463
Telnet Command: bpa........................................................................................................... 464
Telnet Command: csm appe prof.......................................................................................... 465
Telnet Command: csm appe p2p .......................................................................................... 466
Telnet Command: csm appe prot.......................................................................................... 467
Telnet Command: csm appe misc......................................................................................... 467
Telnet Command: csm ucf..................................................................................................... 468
Telnet Command: csm ucf obj INDEX uac............................................................................ 469
Telnet Command: csm ucf obj INDEX wf.............................................................................. 471
Telnet Command: csm wcf.................................................................................................... 472
Telnet Command: ddns log.................................................................................................... 474
Telnet Command: ddns time.................................................................................................. 474
Telnet Command: dos ........................................................................................................... 475
Telnet Command: exit............................................................................................................ 476
Telnet Command: Internet..................................................................................................... 476
Page 13
Vigor2760 Series User’s Guide
xiii
Telnet Command: ip 2ndsubnet............................................................................................. 477
Telnet Command: ip 2ndaddr................................................................................................ 477
Telnet Command: ip 2ndmask............................................................................................... 478
Telnet Command: ip aux........................................................................................................ 478
Telnet Command: ip addr...................................................................................................... 479
Telnet Command: ip nmask................................................................................................... 479
Telnet Command: ip arp........................................................................................................ 480
Telnet Command: ip dhcpc.................................................................................................... 481
Telnet Command: ip ping....................................................................................................... 482
Telnet Command: ip tracert................................................................................................... 482
Telnet Command: ip telnet..................................................................................................... 483
Telnet Command: ip rip ......................................................................................................... 483
Telnet Command: ip wanrip................................................................................................... 483
Telnet Command: ip route..................................................................................................... 485
Telnet Command: ip igmp_proxy........................................................................................... 486
Telnet Command: ip wanaddr................................................................................................ 486
Telnet Command: ip wanttr.................................................................................................... 487
Telnet Command: ip dmz....................................................................................................... 487
Telnet Command: ip session................................................................................................. 488
Telnet Command: ip bandwidth............................................................................................. 489
Telnet Command: ip bindmac................................................................................................ 490
Telnet Command: ip maxnatuser........................................................................................... 490
Telnet Command: ip6 addr.................................................................................................... 491
Telnet Command: ip6 dhcp req_opt...................................................................................... 491
Telnet Command: ip6 dhcp client.......................................................................................... 492
Telnet Command: ip6 dhcp server ........................................................................................ 493
Telnet Command: ip6 internet ............................................................................................... 495
Telnet Command: ip6 neigh................................................................................................... 496
Telnet Command: ip6 pneigh................................................................................................. 497
Telnet Command: ip6 route................................................................................................... 497
Telnet Command: ip6 ping..................................................................................................... 498
Telnet Command: ip6 tracert................................................................................................. 499
Telnet Command: ip6 tspc..................................................................................................... 499
Telnet Command: ip6 radvd .................................................................................................. 500
Telnet Command: ip6 mngt ................................................................................................... 500
Telnet Command: ip6 online.................................................................................................. 501
Telnet Command: ip6 aiccu................................................................................................... 502
Telnet Command: ip6 ntp ...................................................................................................... 503
Telnet Command: ipf view..................................................................................................... 503
Telnet Command: ipf set........................................................................................................ 504
Telnet Command: ipf rule ...................................................................................................... 505
Telnet Command: ipf flowtrack.............................................................................................. 510
Telnet Command: Log........................................................................................................... 510
Telnet Command: mngt ftpport.............................................................................................. 512
Telnet Command: mngt httpport............................................................................................ 512
Telnet Command: mngt httpsport.......................................................................................... 512
Telnet Command: mngt telnetport......................................................................................... 512
Telnet Command: mngt sshport ............................................................................................ 513
Telnet Command: mngt telnetport......................................................................................... 513
Telnet Command: mngt sshport ............................................................................................ 513
Telnet Command: mngt ftpserver.......................................................................................... 514
Telnet Command: mngt noping ............................................................................................. 514
Telnet Command: mngt defenseworm .................................................................................. 516
Telnet Command: mngt rmtcfg.............................................................................................. 516
Telnet Command: mngt echoicmp......................................................................................... 517
Telnet Command: mngt accesslist ........................................................................................ 517
Telnet Command: mngt snmp ............................................................................................... 518
Telnet Command: msubnet switch........................................................................................ 519
Telnet Command: msubnet addr........................................................................................... 519
Telnet Command: msubnet nmask........................................................................................ 520
Page 14
Vigor2760 Series User’s Guide
xiv
Telnet Command: msubnet status......................................................................................... 520
Telnet Command: msubnet dhcps......................................................................................... 520
Telnet Command: msubnet nat ............................................................................................. 521
Telnet Command: msubnet gateway..................................................................................... 521
Telnet Command: msubnet ipcnt........................................................................................... 522
Telnet Command: msubnet talk............................................................................................. 522
Telnet Command: msubnet startip ........................................................................................ 523
Telnet Command: msubnet pppip ......................................................................................... 523
Telnet Command: msubnet nodetype ................................................................................... 523
Telnet Command: msubnet primWINS .................................................................................. 524
Telnet Command: msubnet secWINS................................................................................... 524
Telnet Command: msubnet tftp ............................................................................................. 525
Telnet Command: msubnet mtu ............................................................................................ 525
Telnet Command: object ip obj.............................................................................................. 525
Telnet Command: object ip grp.............................................................................................. 527
Telnet Command: object service obj ..................................................................................... 529
Telnet Command: object service grp..................................................................................... 530
Telnet Command: object kw.................................................................................................. 531
Telnet Command: object fe.................................................................................................... 532
Telnet Command: port........................................................................................................... 535
Telnet Command: portmaptime............................................................................................. 535
Telnet Command: qos setup.................................................................................................. 536
Telnet Command: qos class.................................................................................................. 538
Telnet Command: qos type.................................................................................................... 539
Telnet Command: quit ........................................................................................................... 540
Telnet Command: show lan1................................................................................................. 540
Telnet Command: show lan2................................................................................................. 540
Telnet Command: show dhcp................................................................................................ 540
Telnet Command: show dmz................................................................................................. 541
Telnet Command: show dns.................................................................................................. 541
Telnet Command: show openport ......................................................................................... 542
Telnet Command: show nat................................................................................................... 542
Telnet Command: show portmap........................................................................................... 542
Telnet Command: show pmtime............................................................................................ 542
Telnet Command: show session............................................................................................ 543
Telnet Command: show status.............................................................................................. 543
Telnet Command: show adsl................................................................................................. 543
Telnet Command: show statistic............................................................................................ 544
Telnet Command: srv dhcp badip.......................................................................................... 544
Telnet Command: srv dhcp public......................................................................................... 544
Telnet Command: srv dhcp dns1........................................................................................... 545
Telnet Command: srv dhcp dns2........................................................................................... 546
Telnet Command: srv dhcp frcdnsmanl................................................................................. 547
Telnet Command: srv dhcp gateway..................................................................................... 547
Telnet Command: srv dhcp ipcnt........................................................................................... 548
Telnet Command: srv dhcp off............................................................................................... 548
Telnet Command: srv dhcp on............................................................................................... 548
Telnet Command: srv dhcp relay........................................................................................... 548
Telnet Command: srv dhcp startip......................................................................................... 549
Telnet Command: srv dhcp status......................................................................................... 549
Telnet Command: srv dhcp leasetime................................................................................... 550
Telnet Command: srv dhcp nodetype.................................................................................... 550
Telnet Command: srv dhcp primWINS.................................................................................. 551
Telnet Command: srv dhcp secWINS ................................................................................... 551
Telnet Command: srv dhcp expired_RecycleIP .................................................................... 552
Telnet Command: srv dhcp tftp.............................................................................................. 552
Telnet Command: srv dhcp option......................................................................................... 552
Telnet Command: srv nat dmz............................................................................................... 554
Telnet Command: sys cfg...................................................................................................... 558
Telnet Command: sys cmdlog............................................................................................... 559
Page 15
Vigor2760 Series User’s Guide
xv
Telnet Command: sys ftpd..................................................................................................... 559
Telnet Command: sys domainname...................................................................................... 559
Telnet Command: sys iface................................................................................................... 560
Telnet Command: sys name.................................................................................................. 562
Telnet Command: sys passwd............................................................................................... 562
Telnet Command: sys reboot................................................................................................. 562
Telnet Command: sys autoreboot ......................................................................................... 563
Telnet Command: sys commit............................................................................................... 563
Telnet Command: sys tftpd.................................................................................................... 563
Telnet Command: sys cc....................................................................................................... 563
Telnet Command: sys version............................................................................................... 564
Telnet Command: sys qrybuf................................................................................................. 564
Telnet Command: sys pollbuf................................................................................................ 564
Telnet Command: sys britask................................................................................................ 565
Telnet Command: sys tr069................................................................................................... 565
Telnet Command: sys sip_alg ............................................................................................... 567
Telnet Command: sys license................................................................................................ 567
Telnet Command: sys diag_log............................................................................................. 568
Telnet Command: testmail..................................................................................................... 570
Telnet Command: upnp off.................................................................................................... 570
Telnet Command: upnp on.................................................................................................... 570
Telnet Command: upnp nat................................................................................................... 570
Telnet Command: upnp service............................................................................................. 571
Telnet Command: upnp subscribe......................................................................................... 571
Telnet Command: upnp tmpvs............................................................................................... 572
Telnet Command: upnp wan.................................................................................................. 573
Telnet Command: vigbrg on .................................................................................................. 573
Telnet Command: vigbrg off .................................................................................................. 573
Telnet Command: vigbrg status............................................................................................. 573
Telnet Command: vigbrg cfgip............................................................................................... 574
Telnet Command: vigbrg wan1on.......................................................................................... 574
Telnet Command: vigbrg wan1off.......................................................................................... 574
Telnet Command: vpn l2lset.................................................................................................. 574
Telnet Command: vpn l2lDrop............................................................................................... 575
Telnet Command: vpn dinset................................................................................................. 575
Telnet Command: vpn subnet................................................................................................ 576
Telnet Command: vpn setup.................................................................................................. 577
Telnet Command: vpn option................................................................................................. 578
Telnet Command: vpn mroute............................................................................................... 582
Telnet Command: vpn list...................................................................................................... 582
Telnet Command: vpn remote............................................................................................... 583
Telnet Command: vpn 2ndsubnet ......................................................................................... 584
Telnet Command: vpn NetBios.............................................................................................. 584
Telnet Command: vpn mss.................................................................................................... 585
Telnet Command: vpn ike...................................................................................................... 586
Telnet Command: vpn Multicast............................................................................................ 586
Telnet Command: vpn pass2nd............................................................................................. 586
Telnet Command: vpn pass2nat............................................................................................ 587
Telnet Command: wan ppp_mru........................................................................................... 587
Telnet Command: wan mtu.................................................................................................... 588
Telnet Command: wan DF_check......................................................................................... 588
Telnet Command: wan disable.............................................................................................. 588
Telnet Command: wan enable............................................................................................... 588
Telnet Command: wan forward.............................................................................................. 589
Telnet Command: wan status................................................................................................ 589
Telnet Command: wan vdsl................................................................................................... 590
Telnet Command: wan detect................................................................................................ 590
Telnet Command: wan lb....................................................................................................... 591
Telnet Command: wan mvlan................................................................................................ 592
Telnet Command: wan multifno............................................................................................. 593
Page 16
Vigor2760 Series User’s Guide
xvi
Telnet Command: wl acl........................................................................................................ 594
Telnet Command: wl config................................................................................................... 595
Telnet Command: wl set........................................................................................................ 597
Telnet Command: wl act........................................................................................................ 598
Telnet Command: wl iso_vpn ................................................................................................ 598
Telnet Command: wl wmm.................................................................................................... 598
Telnet Command: wl ht.......................................................................................................... 600
Telnet Command: wl restart................................................................................................... 601
Telnet Command: wl btnctl.................................................................................................... 601
Telnet Command: wl efuse.................................................................................................... 601
Telnet Command: wan vlan................................................................................................... 602
Telnet Command: wol............................................................................................................ 602
Page 17
Vigor2760 Series User’s Guide
1
IInnttrroodduuccttiioonn
NNoottee:: TThhiiss iiss aa ggeenneerriicc IInntteerrnnaattiioonnaall vveerrssiioonn ooff tthhee
uusseerr gguuiiddee.. SSppeecciiffiiccaattiioonn,, ccoommppaattiibbiilliittyy aanndd ffeeaattuurreess
vvaarryy bbyy rreeggiioonn.. FFoorr ssppeecciiffiicc uusseerr gguuiiddeess ssuuiittaabbllee ffoorr
yyoouurr rreeggiioonn oorr pprroodduucctt,, pplleeaassee ccoonnttaacctt llooccaall
ddiissttrriibbuuttoorr..
Vigor2760 series is a VDSL2 router. It integrates IP layer QoS, NAT session/bandwidth
management to help users control works well with large bandwidth.
With the development of NGN (Next Generation Network), you may recently hear the news
about FTTx deployment in your local area or even have already subscribed the unbundling last
mile service (e.g. VDSL2) from local ITSP for FTTx. As adopting FTTx, the main question
for end users is whether your legacy router could fully utilize its bandwidth or not.
DrayTek launches Vigor 2760 series – High speed router, perfectly complied with VDSL2
environment including Vigor2760, Vigor2760n and Vigor2760Vn for speed-wanted customers.
With high throughput performance and secured broadband connectivity provided by Vigor
2760 series, you can simultaneously engage these bandwidth-intensive applications, such as
high-definition video streaming, online gaming, and Internet telephony / access.
Note: This manual is written based on the standard firmware version of Vigor2760 series and
suitable for all of the countries except for UK area. For product enquiries in the UK, Ireland
and Channel Islands, please contact the UK office.
DrayTek UK Office
Sales Tel: 020 8381 5500
Email: info@draytek.co.uk
Page 18
Vigor2760 Series User’s Guide
2
11..11 FFeeaattuurreess
ADSL2/2+ & VDSL2
Compliant with ITU-T G.993.2 & G.997.1
Support Band Plan 998 & 997
Support Annex A / Annex B
VDSL2 Profile 8a/8b/8c/8d/12a/12b/17a/30a
Capability Fall-back to ADSL2/2+
Multi-VLAN
Multi-PVC
Internet
Support IPv4 & IPv6
Support PPPoE/PPPoA
Support DHCP/Static IP
Internet connection over 3G/4G USB Dongle
Multi-VLAN/Multi-PVC for triple play
VPN
2 VPN Tunnels
Built-in PPTP/L2TP/IPsec VPN server
VPN Passthough (PPTP/L2TP/IPsec)
IPsec Main/Aggressive Mode
IKE Authentication (PSK & X.509)
PPTP MPPE
L2TP over IPsec
Security
Object-based Firewall
MAC Address Filter
SPI (Stateful Packet Inspection)
DoS/DDoS Prevention
IM/P2P Applications Filter
URL Content Filter
Global View Web Content Filter
Bind IP to MAC
NAT/Routing
DMZ Host
Port Forwarding & Redirection
Route Policy
Static Route
RIPv2
Network Feature
Two subnets(VLAN)
LAN Port Mirror
Bandwidth/Session Management
QoS by IP, Port, Applications
Dynamic DNS
LAN DNS
UPnP
IGMP proxy & snooping
Wake on LAN
Bonjour
Printer Sharing
FTP Server for File Sharing by a USB Memory
Stick/USB HDD with FAT32 Format
System Maintenance
Web Syslog
HTTP/HTTPS User Interface
CLI over Telnet/SSH/Web UI
Configuration Backup/Restore
Administrator Access Control
Restricted User Mode
Page 19
Vigor2760 Series User’s Guide
3
Flow Monitor
Built-in Diagnostic Function
E-mail/SMS Alert
SNMP v1/v2c
TR-069 (Compliance with VigorACS SI)
Wireless AP (n model)
Support 2T2R 2.4GHz, Single Band
IEEE802.11n Compliant
64/128-bit WEP, WPA/WPA2
WDS (Wireless Distribution System)
MAC Address Access Control
WPS
Wireless Client List
Access Point Discovery
Hidden SSID
Multiple SSID
WMM
VoIP (V model)
Protocol: SIP, RTP/RTCP
6 SIP Registrars
G.168 Line Echo-cancellation
VoIP Status
PSTN Loop Through
Codec Features :
G.711 A/μ law
G.723.1
G.726
G.729 A/B
VAD/CNG
DTMF Relay :
In Band
Out Band (RFC-2833)
SIP Info
FAX/Modem Support :
G.711 Pass-through
T.38 for fax Sending/Receiving
Supplemental Services :
Call Hold/Retrieve
Call Waiting
CLIR (Calling Line Identification Restriction)
Call Forwarding (Always, Busy and No Answer)
Call Barring (Incoming / Outgoing)
Hotline
DND (Do Not Disturb)
Call Transfer
MWI (Message Waiting Indicator) (RFC-3842)
Firmware Updates
Firmware updates for your product ensure that you have the latest set of features, security
updates and improvements for your product.
Please note that if your Vigor 2760 product has firmware version 1.x.x or earlier then it can
only update to later 1.x.x firmware. If your Vigor 2760 has firmware version 3.7.5 or later
(‘Delight/DrayOS’ hardware) then you can upgrade to any compatible later firmware. You
cannot use Delight/DrayOS firmware on original (classic) Vigor 2760 hardware or vice-versa.
This manual applies only to DrayOS/Delight hardware/firmware.
Page 20
Vigor2760 Series User’s Guide
4
11..22 PPaacckkaaggee aanndd CCoonntteenntt
Antenna (n models)
CD
RJ-45 Cable
(Ethernet)
Quick Start Guide
The type of the power adapter depends on the country that the router will be installed. *
The maximum power consumption is 17-23 Watt.
UK-type Power Adapter
EU-type Power Adapter
USA/Taiwan-type Power Adapter
AU/NZ-type Power Adapter
Page 21
Vigor2760 Series User’s Guide
5
11..33 LLEEDD IInnddiiccaattoorrss aanndd CCoonnnneeccttoorrss
Before you use the Vigor router, please get acquainted with the LED indicators and connectors
first.
11..33..11 FFoorr VViiggoorr22776600
LED Status Explanation
Blinking The router is powered on and running normally.
(ACT)
Off The router is powered off.
On The DSL port is connected.
Blinking
(Slowly)
The router is ready.
DSL (Green)
Blinking
(Quickly)
The connection is training.
On (Green) The port is connected.
~
LAN1/2/3/4
Blinking
(Green)
The data is transmitting.
~
USB1/2
On A USB device is connected and active.
Page 22
Vigor2760 Series User’s Guide
6
Interface Description
PWR Connector for a power adapter.
I / O
Power switch.
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
VDSL/ADSL Connector for accessing the Internet.
USB (1-2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or
3G backup.
LAN (1-4) Connectors for local network devices.
Page 23
Vigor2760 Series User’s Guide
7
11..33..22 FFoorr VViiggoorr22776600nn
LED Status Explanation
Blinking The router is powered on and running normally.
(Activity)
Off The router is powered off.
On (Green) The wireless access point is ready.
Blinking
(Green)
The data is transmitting via wireless connection.
Blinking
(Orange)
Blinks with one second cycle for two minutes. The WPS
function is active.
(Wireless LAN
On/Off/WPS)
Off The wireless access point is turned off.
On The DSL port is connected.
Blinking
(Slowly)
The router is ready.
DSL (Green)
Blinking
(Quickly)
The router is trying to connect to Internet.
On The port is connected.
~
LAN1/2/3/4
Blinking
(Green)
The data is transmitting.
~
USB1/2
On A USB device is connected and active.
Page 24
Vigor2760 Series User’s Guide
8
Interface Description
PWR Connector for a power adapter.
I / O Power switch.
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you see
the ACT LED begins to blink rapidly than usual, release the button. Then
the router will restart with the factory default configuration.
WLAN
ON/OFF/WPS
WLAN WPS - Press this button for 2 seconds to wait for client device making
network connection through WPS. When the LED lights up, the WPS connection
will be on.
WLAN ON/OFF - Press the button once to enable (WLAN LED on) or disable
(WLAN LED off) wireless connection.
VDSL/ADSL Connector for accessing the Internet.
USB (1-2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or
3G backup.
LAN (1-4) Connectors for local network devices.
Page 25
Vigor2760 Series User’s Guide
9
11..33..33 FFoorr VViiggoorr22776600VVnn
LED Status Explanation
Blinking The router is powered on and running normally.
(ACT)
Off The router is powered off.
On A PSTN phone call comes (in and out). However, when
the phone call is disconnected, the LED will be off for
awhile.
(LINE)
Off There is no PSTN phone call.
On The phone connected to this port is off-hook.
Off The phone connected to this port is on-hook.
(Phone1/Phone2)
Blinking A phone call comes.
On (Green) The wireless access point is ready.
Blinking
(Green)
The data is transmitting via wireless connection.
Blinking
(Orange)
Blinks with one second cycle for two minutes. The WPS
function is active.
(Wireless LAN
On/Off/WPS)
Off The wireless access point is turned off.
On The DSL port is connected.
Blinking
(Slowly)
The router is ready.
DSL (Green)
Blinking
(Quickly)
The router is trying to connect to Internet.
On The port is connected.
~
LAN1/2/3/4
Blinking
(Green)
The data is transmitting.
~
USB1/2
On A USB device is connected and active.
Page 26
Vigor2760 Series User’s Guide
10
Interface Description
PWR Connector for a power adapter.
I / O
Power switch.
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is
blinking). Press the hole and keep for more than 5 seconds. When you
see the ACT LED begins to blink rapidly than usual, release the button.
Then the router will restart with the factory default configuration.
WLAN
ON/OFF/WPS
WLAN WPS - Press this button for 2 seconds to wait for client device making
network connection through WPS. When the LED lights up, the WPS
connection will be on.
WLAN ON/OFF - Press the button once to enable (WLAN LED on) or disable
(WLAN LED off) wireless connection.
VDSL/ADSL Connector for accessing the Internet.
USB (1-2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or
3G backup.
LAN (1-4) Connectors for local network devices.
Interface Description
LINE Connector for PSTN life line.
Phone1/Phone2 Connector of analog phone for VoIP communication.
Page 27
Vigor2760 Series User’s Guide
11
11..44 HHaarrddwwaarree IInnssttaallllaattiioonn
Before starting to configure the router, you have to connect your devices correctly.
1. Connect the xDSL interface to the external XDSL splitter with an XDSL line cable for
all models. For Vigor2760Vn, also connect Line interface to external XDSL splitter.
2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device
allows you to connect 4 PCs directly.
3. Connect Phone port to a conventional analog telephone (for V model only).
4. Connect detachable antennas to the router for Vigor2760 series (for n model only).
5. Connect one end of the power cord to the power port of this device. Connect the other
end to the wall outlet of electricity.
6. Power on the router.
7. Check the ACT and DSL, LAN LEDs to assure network connection.
(For the hardware connection, we take “n” model as an example.)
Page 28
Vigor2760 Series User’s Guide
12
11..55 PPrriinntteerr IInnssttaallllaattiioonn
You can install a printer onto the router for sharing printing. All the PCs connected this router
can print documents via the router. The example provided here is made based on Windows 7.
For installation on other Windows systems, please visit www.DrayTek.com.
Before using it, please follow the steps below to configure settings for connected computers
(or wireless clients).
1. Connect the printer with the router through USB/parallel port.
2. Open All Programs>>Getting Started>>Devices and Printers.
Page 29
Vigor2760 Series User’s Guide
13
3. Click Add a printer.
4. A dialog will appear. Click Add a local printer and click Next.
5. In this dialog, choose Create a new port. In the field of Type of port, use the drop
down list to select Standard TCP/IP Port. Then, click Next.
Page 30
Vigor2760 Series User’s Guide
14
6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Hostname or
IP Address and type 192.168.1.1 as the Port name. Then, click Next.
7. Click Standard and choose Generic Network Card.
Page 31
Vigor2760 Series User’s Guide
15
8. Now, your system will ask you to choose right name of the printer that you installed onto
the router. Such step can make correct driver loaded onto your PC. When you finish the
selection, click Next.
9. Type a name for the chosen printer. Click Next.
Page 32
Vigor2760 Series User’s Guide
16
10. Choose Do not share this printer and click Next.
11. Then, in the following dialog, click Finish.
Page 33
Vigor2760 Series User’s Guide
17
12. The new printer has been added and displayed under Printers and Faxes. Click the new
printer icon and click Printer server properties.
13. Edit the property of the new printer you have added by clicking Configure Port.
Page 34
Vigor2760 Series User’s Guide
18
14. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next
please refer to the red rectangle for choosing the correct protocol and LPR name.
The printer can be used for printing now. Most of the printers with different manufacturers are
compatible with vigor router.
Page 35
Vigor2760 Series User’s Guide
19
Note 1: Some printers with the fax/scanning or other additional functions are not supported.
If you do not know whether your printer is supported or not, please visit www.draytek.com
to find out the printer list. Open Support >FAQ/Application Notes; find out the link of
USB>>Printer Server and click it.
Then, click the What types of printers are compatible with Vigor router? link.
Note 2: Vigor router supports printing request from computers via LAN ports but not WAN
port.
Page 36
Vigor2760 Series User’s Guide
20
11..66 AAcccceessssiinngg WWeebb PPaaggee
1. Make sure your PC connects to the router correctly.
You may either simply set up your computer to get IP dynamically from the router or set
up the IP address of the computer to be the same subnet as the default IP address of
Vigor router 192.168.1.1. For the detailed information, please refer to the later section Trouble Shooting of the guide.
2. Open a web browser on your PC and type http://192.168.1.1. The following window
will be open to ask for username and password.
3. Please type “admin/admin” as the Username/Password and click Login.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
Page 37
Vigor2760 Series User’s Guide
21
4. Now, the Main Screen will appear.
Note: The home page will be different slightly in accordance with the type of the
router you have.
5. The web page can be logged out according to the chosen condition. The default setting is
Auto Logout, which means the web configuration system will logout after 5 minutes
without any operation. Change the setting for your necessity.
11..77 CChhaannggiinngg PPaasssswwoorrdd
Please change the password for the original security of the router.
1. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password.
2. Please type “admin/admin” as Username/Password for accessing into the web user
interface with admin mode.
3. Go to System Maintenance page and choose Administrator Password.
Page 38
Vigor2760 Series User’s Guide
22
4. Enter the login password (the default is “admin”) on the field of Old Password. Type
New Password and Confirm Password. Then click OK to continue.
Note: The maximum length of the password you can set is 23 characters.
5. Now, the password has been changed. Next time, use the new password to access the
Web user interface for this router.
Note: Even the password is changed, the Username for logging onto the web user
interface is still “admin”.
11..88 IInnttrroodduucciinngg DDaasshhbbooaarrdd
Dashboard shows the connection status including System Information, IPv4 Internet Access,
IPv6 Internet Access, Interface (physical connection), Security and Quick Access.
Click Dashboard from the main menu on the left side of the main page.
Page 39
Vigor2760 Series User’s Guide
23
A web page with default selections will be displayed on the screen. Refer to the following
figure:
11..88..11 VViirrttuuaall PPaanneell
On the top of the Dashboard, a virtual panel (simulating the physical panel of the router)
displays the physical interface connection. It will be refreshed every five seconds.
The LED lights or blinks according to the physical connection on the router. For detailed
information about the LED display, refer to 1.2 LED Indicators and Connectors.
11..88..22 NNaammee wwiitthh aa LLiinnkk
A name with a link (e.g., Router Name, Current Time, WAN1 and etc.) below means you can
click it to open the configuration page for modification.
Page 40
Vigor2760 Series User’s Guide
24
11..88..33 QQuuiicckk AAcccceessss ffoorr CCoommmmoonn UUsseedd MMeennuu
All the menu items can be accessed and arranged orderly on the left side of the main page for
your request. However, some important and common used menu items which can be
accessed in a quick way just for convenience.
Look at the right side of the Dashboard. You will find a group of common used functions
grouped under Quick Access.
The function links of System Status, Dynamic DDNS, TR-069, IM/P2P Block, Schedule,
Syslog/Mail Alert, RADIUS, Firewall Object Setting and Data Flow Monitor are displayed
here. Move your mouse cursor on any one of the links and click on it. The corresponding
setting page will be open immediately.
In addition, quick access for VPN security settings such as Remote Dial-in User and LAN to
LAN are located on the bottom of this page. Scroll down the page to find them and use them if
required.
Note that there is a plus (
) icon located on the left side of VPN/LAN/WLAN. Click it to
review the VPN/LAN/WLAN connection(s) used presently.
Host connected physically to the router via LAN port(s) will be displayed with green circles in
the field of Connected.
All of the hosts (including wireless clients) displayed with Host ID, IP Address and MAC
address indicates that the traffic would be transmitted through LAN port(s) and then the WAN
port. The purpose is to perform the traffic monitor of the host(s).
Page 41
Vigor2760 Series User’s Guide
25
11..88..44 GGUUII MMaapp
All the functions the router supports are listed with table clearly in this page. Users can click
the function link to access into the setting page of the function for detailed configuration.
Click the icon on the top of the main screen to display all the functions.
Page 42
Vigor2760 Series User’s Guide
26
11..88..55 WWeebb CCoonnssoollee
It is not necessary to use the telnet command via DOS prompt. The changes made by using
web console have the same effects as modified through web user interface. The
functions/settings modified under Web Console also can be reviewed on the web user
interface.
Click the Web Console icon on the top of the main screen to open the following screen.
Page 43
Vigor2760 Series User’s Guide
27
11..88..66 CCoonnffiigg BBaacckkuupp
There is one way to store current used settings quickly by clicking the Config Backup icon. It
allows you to backup current settings as a file. Such configuration file can be restored by using
System Maintenance>>Configuration Backup.
Simply click the icon on the top of the main screen and a pop up dialog will appear.
Click Save to store the setting.
11..88..77 LLooggoouutt
Click this icon to exit the web user interface.
Page 44
Vigor2760 Series User’s Guide
28
11..99 OOnnlliinnee SSttaattuuss
11..99..11 PPhhyyssiiccaall CCoonnnneeccttiioonn
Such page displays the physical connection status such as LAN connection status, WAN
connection status, ADSL information, and so on.
PPhhyyssiiccaall CCoonnnneeccttiioonn ffoorr IIPPvv44 PPrroottooccooll
Note: If the firmware which supports Vectoring has been installed to your Vigor router,
you will see a short message of “with Vectoring support” near to VDLS2 Information.
Such feature is available for VDSL2 only.
Page 45
Vigor2760 Series User’s Guide
29
PPhhyyssiiccaall CCoonnnneeccttiioonn ffoorr IIPPvv66 PPrroottooccooll
Detailed explanation (for IPv4) is shown below:
Item Description
LAN Status
Primary DNS-Displays the primary DNS server address
for WAN interface.
Secondary DNS -Displays the secondary DNS server
address for WAN interface.
IP Address-Displays the IP address of the LAN interface.
TX Packets-Displays the total transmitted packets at the
LAN interface.
RX Packets-Displays the total received packets at the LAN
interface.
WAN1/WAN2/WAN3
Status
Enable – Yes in red means such interface is available but
not enabled. Yes in green means such interface is enabled.
Line – Displays the physical connection (VDSL, ADSL,
Ethernet, or USB) of this interface.
Name – Display the name of the router.
Mode - Displays the type of WAN connection (e.g.,
PPPoE).
Up Time - Displays the total uptime of the interface.
IP - Displays the IP address of the WAN interface.
GW IP - Displays the IP address of the default gateway.
TX Packets - Displays the total transmitted packets at the
WAN interface.
TX Rate - Displays the speed of transmitted octets at the
WAN interface.
RX Packets - Displays the total number of received packets
at the WAN interface.
RX Rate - Displays the speed of received octets at the
WAN interface.
Page 46
Vigor2760 Series User’s Guide
30
Detailed explanation (for IPv6) is shown below:
Item Description
LAN Status
IP Address- Displays the IPv6 address of the LAN
interface..
TX Packets-Displays the total transmitted packets at the
LAN interface.
RX Packets-Displays the total received packets at the LAN
interface.
TX Bytes - Displays the speed of transmitted octets at the
LAN interface.
RX Bytes - Displays the speed of received octets at the
LAN interface.
WAN IPv6 Status
Enable – No in red means such interface is available but
not enabled. Yes in green means such interface is enabled.
No in red means such interface is not available.
Mode - Displays the type of WAN connection (e.g., TSPC).
Up Time - Displays the total uptime of the interface.
IP - Displays the IP address of the WAN interface.
Gateway IP - Displays the IP address of the default
gateway.
Note: The words in green mean that the WAN connection of that interface is ready for
accessing Internet; the words in red mean that the WAN connection of that interface is not
ready for accessing Internet.
11..99..22 VViirrttuuaall WWAANN
Such page displays the virtual WAN connection information.
Virtual WAN are used by TR-069 management, VoIP service and so on.
The field of Application will list the purpose of such WAN connection.
Page 47
Vigor2760 Series User’s Guide
31
11..1100 SSaavviinngg CCoonnffiigguurraattiioonn
Each time you click OK on the web page for saving the configuration, you can find messages
showing the system interaction with you.
Ready indicates the system is ready for you to input settings.
Settings Saved means your settings are saved once you click Finish or OK button.
Page 48
Vigor2760 Series User’s Guide
32
This page is left blank.
Page 49
Vigor2760 Series User’s Guide
33
Q
Quuiicckk SSeettuupp
There are several setup wizards offered for you to configure the router simply and quickly.
Quick Start Wizard – used for building network connection, Internet access.
Service Activation Wizard – used for activating the web content filter service.
VPN Client Wizard – used for establishing VPN tunnel; the router is treated as a VPN
client.
VPN Server Wizard – used for establishing VPN tunnel; the router is treated as a VPN
server.
Wireless Wizard – used for building wireless LAN connection.
VoIP Wizard – used for establishing VoIP profile.
22..11 QQuuiicckk SSttaarrtt WWiizzaarrdd
Quick Start Wizard can help you to deploy and use the router easily and quickly. The first
screen of Quick Start Wizard is entering login password. After typing the password, please
click Next.
Page 50
Vigor2760 Series User’s Guide
34
On the next page as shown below, please select the WAN interface that you use. If DSL
interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if
3G USB modem is used, please choose WAN3. Then click Next for next step.
WAN1, WAN2, and WAN3 will bring up different configuration page. Refer to the following
sections for detailed information.
Page 51
Vigor2760 Series User’s Guide
35
22..11..11 FFoorr WWAANN11 ((AADDSSLL//VVDDSSLL22))
WAN1 is specified for ADSL or VDSL2 connection.
Available settings are explained as follows:
Item Description
Display Name
Type a name to identify such WAN.
DSL Mode
Specify the physical mode (VDSL2 only or ADSL only) for
such router manually.
VLAN Tag insertion
(VDSL2)/(ADSL)
The settings configured in this field are available for WAN1
and WAN2.
Enable – Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets on
the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN1.
Disable – Disable the function of VLAN with tag.
Tag value – Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority – Type the packet priority number for such VLAN.
The range is from 0 to 7.
You have to select the appropriate Internet access type according to the information from
your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE
interface. In addition, the field of For ADSL Only will be available only when ADSL is
detected. Then click Next for next step.
Page 52
Vigor2760 Series User’s Guide
36
PPPPPPooEE//PPPPPPooAA
1. Choose WAN1 as WAN Interface and click the Next button; you will get the following
page.
Available settings are explained as follows:
Item Description
Protocol
There are two modes offered for you to choose for WAN1
interface.
Choose PPPoE/PPPoA as the protocol.
For ADSL Only
Such field is provided for ADSL only. You have to choose
encapsulation and type the values for VPI and VCI. Or, click
Auto detect to find out the best values.
Fixed IP
Click Yes to enable Fixed IP feature.
IP Address
Type the IP address if Fixed IP is enabled.
Primary DNS
Type in the primary IP address for the router.
Secondary DNS
Type in secondary IP address for necessity in the future.
Back
Click it to return to previous setting page.
Page 53
Vigor2760 Series User’s Guide
37
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
2. After finished the above settings, simply click Next. Manually enter the
Username/Password provided by your ISP
Available settings are explained as follows:
Item Description
Service Name
(Optional)
Enter the description of the specific network service.
User Name
Assign a specific valid user name provided by the ISP.
Note: The maximum length of the user name you can set is
63 characters.
Password
Assign a valid password provided by the ISP.
Note: The maximum length of the password you can set is 62
characters.
Confirm Password
Retype the password.
Back
Click it to return to previous setting page.
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
Page 54
Vigor2760 Series User’s Guide
38
3. After finished the above settings, click Next for viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 55
Vigor2760 Series User’s Guide
39
MMPPooAA // SSttaattiicc oorr DDyynnaammiicc IIPP
1. Choose WAN1 as WAN Interface and click the Next button; you will get the following
page.
Available settings are explained as follows:
Item Description
Protocol
There are two modes offered for you to choose for WAN1
interface.
Choose MPoA / Static or Dynamic IP as the protocol.
For ADSL Only
Such field is provided for ADSL only. You have to choose
encapsulation and type the values for VPI and VCI. Or, click
Auto detect to find out the best values.
Fixed IP
Click Yes to enable Fixed IP feature.
IP Address
Type the IP address if Fixed IP is enabled.
Subnet Mask
Type the subnet mask.
Page 56
Vigor2760 Series User’s Guide
40
Primary DNS
Type in the primary IP address for the router.
Secondary DNS
Type in secondary IP address for necessity in the future.
Back
Click it to return to previous setting page.
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
2. Please type in the IP address/mask/gateway information originally provided by your ISP.
Then click Next for viewing summary of such connection.
3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
4. Now, you can enjoy surfing on the Internet.
Page 57
Vigor2760 Series User’s Guide
41
22..11..22 FFoorr WWAANN22 ((EEtthheerrnneett))
WAN2 is dedicated to physical mode in Ethernet. If you choose WAN2, please specify
physical type. Then, click Next.
Available settings are explained as follows:
Item Description
Display Name
Type a name for the router.
VLAN Tag insertion
The settings configured in this field are available for WAN1
and WAN2.
Enable – Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets on
the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN2.
Disable – Disable the function of VLAN with tag.
Tag value – Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority – Type the packet priority number for such VLAN.
The range is from 0 to 7.
On the next page as shown below, please select the appropriate Internet access type according
to the information from your ISP. For example, you should select PPPoE mode if the ISP
provides you PPPoE interface. Then click Next for next step.
Page 58
Vigor2760 Series User’s Guide
42
PPPPPPooEE
1. Choose WAN2 as the WAN Interface and click the Next button. The following page will
be open for you to specify Internet Access Type.
2. Click PPPoE as the Internet Access Type. Then click Next to continue.
Available settings are explained as follows:
Item Description
Service Name
(Optional)
Enter the description of the specific network service.
User Name
Assign a specific valid user name provided by the ISP.
Note: The maximum length of the user name you can set is
63 characters.
Password
Assign a valid password provided by the ISP.
Note: The maximum length of the password you can set is 62
characters.
Page 59
Vigor2760 Series User’s Guide
43
Confirm Password
Retype the password.
Back
Click it to return to previous setting page.
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
3. Please manually enter the Username/Password provided by your ISP. Click Next for
viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 60
Vigor2760 Series User’s Guide
44
PPPPTTPP
1. Choose WAN2 as the WAN Interface and click the Next button. The following page will
be open for you to specify Internet Access Type.
2. Click PPTP as the Internet Access Type. Then click Next to continue.
Available settings are explained as follows:
Item Description
User Name
Assign a specific valid user name provided by the ISP.
Note: The maximum length of the user name you can set is
63 characters.
Password
Assign a valid password provided by the ISP.
Note: The maximum length of the password you can set is 62
characters.
Page 61
Vigor2760 Series User’s Guide
45
Confirm Password
Retype the password.
WAN IP
Configuration
Obtain an IP address automatically – the router will get an
IP address automatically from DHCP server.
Specify an IP address – you have to type relational settings
manually.
IP Address - Type the IP address.
Subnet Mask –Type the subnet mask.
Gateway – Type the IP address of the gateway.
Primary DNS –Type in the primary IP address for the router.
Second DNS –Type in secondary IP address for necessity in
the future.
PPTP Server
Type the IP address of the server.
Back
Click it to return to previous setting page.
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
3. Please type in the IP address/mask/gateway information originally provided by your ISP.
Then click Next for viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 62
Vigor2760 Series User’s Guide
46
SSttaattiicc IIPP
1. Choose WAN2 as the WAN Interface and click the Next button. The following page will
be open for you to specify Internet Access Type.
2. Click Static IP as the Internet Access type. Simply click Next to continue.
Available settings are explained as follows:
Item Description
WAN IP
Type the IP address.
Subnet Mask
Type the subnet mask.
Gateway
Type the IP address of gateway.
Primary DNS
Type in the primary IP address for the router.
Secondary DNS
Type in secondary IP address for necessity in the future.
Back
Click it to return to previous setting page.
Page 63
Vigor2760 Series User’s Guide
47
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
3. Please type in the IP address information originally provided by your ISP. Then click
Next for next step.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 64
Vigor2760 Series User’s Guide
48
DDHHCCPP
1. Choose WAN2 as WAN Interface and click the Next button. The following page will be
open for you to specify Internet Access Type.
2. Click DHCP as the Internet Access type. Simply click Next to continue.
Page 65
Vigor2760 Series User’s Guide
49
Available settings are explained as follows:
Item Description
Host Name
Type the name of the host.
Note: The maximum length of the host name you can set is
39 characters.
MAC
Some Cable service providers specify a specific MAC
address for access authentication. In such cases you need to
enter the MAC address.
Back
Click it to return to previous setting page.
Next
Click it to get into the next setting page.
Cancel
Click it to give up the quick start wizard.
3. After finished the settings above, click Next for viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 66
Vigor2760 Series User’s Guide
50
22..11..33 FFoorr WWAANN33 ((UUSSBB))
WAN3 is dedicated to physical mode in USB. If WAN3 is selected, it is not necessary for you
to type any information for such connection.
1. Choose WAN3 as WAN Interface.
2. Then, click Next for getting the following page.
Available settings are explained as follows:
Item Description
Internet Access
Choose one of the selections as the protocol of accessing the
internet.
3G/4G USB Modem
(PPP mode)
SIM Pin code –Type PIN code of the SIM card that will be
used to access Internet. The maximum length of the pin code
you can set is 15 characters.
Modem Initial String – Such value is used to initialize USB
modem. Please use the default value. If you have any
Page 67
Vigor2760 Series User’s Guide
51
question, please contact to your ISP. The maximum length of
the string you can set is 47 characters.
APN Name – APN means Access Point Name which is
provided and required by some ISPs. Type the name and
click Apply.
3G/4G USB Modem
(DHCP mode)
SIM Pin code –Type PIN code of the SIM card that will be
used to access Internet.
Network Mode – Force Vigor router to connect Internet with
the mode specified here. If you choose 4G/3G/2G as network
mode, the router will choose a suitable one according to the
actual wireless signal automatically.
APN Name – APN means Access Point Name which is
provided and required by some ISPs.
3. Then, click Next for viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system
status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.
Page 68
Vigor2760 Series User’s Guide
52
22..22 SSeerrvviiccee AAccttiivvaattiioonn WWiizzaarrdd
Service Activation Wizard can guide you to activate WCF service (Web Content Filter) with a
quick and easy way. For the Service Activation Wizard is only available for admin
operation, therefore, please type “admin/admin” on Username/Password while Logging
into the web user interface.
Service Activation Wizard is a tool which allows you to use trial version or update the license
of WCF directly without accessing into the server (MyVigor) located on
http://myvigor.draytek.com
. For using Web Content Filter Profile, please refer to later section
Web Content Filter Profile for detailed information.
Now, follow the steps listed below to activate WCF feature for your router.
Note: Such function is available only for Admin Mode.
1. Open Wizards>>Service Activation Wizard.
2. The screen of Service Activation Wizard will be shown as follows. Choose the one you
need and click Next. In this case, we choose to activate free trail edition.
Free trial edition: it offers a period of trial for you to get acquainted with WCF function.
Formal edition with license key: you can extend the license valid time manually.
Note: If you activate Formal edition with license key first, the free trial edition will
be invalid.
Page 69
Vigor2760 Series User’s Guide
53
3. In the following page, you can activate the Web content filter services at the same time
or individually. When you finish the selection, please click Next.
Commtouch is the web content filter based on Commtouch operated in the
worldwide. There is a 30-day trial period. After trial, you can purchase DrayTek's
prepared Commtouch GlobalView WCF package from retailing outlets.
BPjM is WCF for German Speaking users. The fragfINN is whitelist for German
Speaking users. The BPjM is ideal for your family to provide more Internet security
for youngsters.
The fragFINN is designed for protecting kids from inadequate web sites. More info
is available at http://www.draytek.de/jugendschutz .
4. Setting confirmation page will be displayed as follows, please click Next.
Page 70
Vigor2760 Series User’s Guide
54
5. Wait for a moment till the following page appears.
When such page appears, you can enable or disable these services for your necessity.
Then, click Finish.
Note: The service will be activated and applied as the default rule configured in
Firewall>>General Setup.
6. Now, the web page will display the service that you have activated according to your
selection(s). The valid time for the free trial of these services is one month.
When all the trial editions for various web content filters had been enabled, the
configuration page of Service Activation Wizard will be invalid as shown below.
Page 71
Vigor2760 Series User’s Guide
55
22..33 VVPPNN CClliieenntt WWiizzaarrdd
Such wizard is used to configure VPN settings for VPN client. Such wizard will guide to set
the LAN-to-LAN profile for VPN dial out connection (from server to client) step by step.
1. Open VPN and Remote Access>>VPN Client Wizard. The following page will appear.
Available settings are explained as follows:
Item Description
LAN-to-LAN Client
Mode Selection
Choose the client mode.
Route Mode/NAT Mode – If the remote network only
allows you to dial in with single IP, please choose this
mode, otherwise please choose Route Mode.
Please choose a
LAN-to-LAN Profile
There are 32 VPN profiles for users to set.
Page 72
Vigor2760 Series User’s Guide
56
2. When you finish the mode and profile selection, please click Next to open the following
page.
In this page, you have to select suitable VPN type for the VPN client profile. There are
six types provided here. Different type will lead to different configuration page. After
making the choices for the client profile, please click Next. You will see different
configurations based on the selection(s) you made.
Page 73
Vigor2760 Series User’s Guide
57
Note: The following descriptions for VPN Type are based on the Route Mode
specified in LAN-to-LAN Client Mode Selection.
When you choose PPTP (None Encryption) or PPTP (Encryption), you will see the
following graphic:
When you choose IPsec, you will see the following graphic:
Page 74
Vigor2760 Series User’s Guide
58
When you choose L2TP, you will see the following graphic:
When you choose L2TP over IPsec (Nice to Have) or L2TP over IPsec (Must), you
will see the following graphic:
Available settings are explained as follows:
Item Description
Profile Name
Type a name for such profile. The length of the file is
limited to 10 characters.
Page 75
Vigor2760 Series User’s Guide
59
Always On
Check to enable router always keep VPN connection.
Server IP/Host Name
for VPN
Type the IP address of the server or type the host name for
such VPN profile.
IKE Authentication
Method
IKE Authentication Method usually applies to those are
remote dial-in user or node (LAN to LAN) which uses
dynamic IP address and IPsec-related VPN connections
such as L2TP over IPsec and IPsec tunnel.
Pre-Shared Key- Specify a key for IKE authentication.
Confirm Pre-Shared Key-Confirm the pre-shared key.
Digital Signature
(X.509)
Click Digital Signature to invoke this function.
Peer ID – Choose the peer ID selection from the drop down
list.
Local ID – Choose Alternative Subject Name First or
Subject Name First.
Local Certificate – Use the drop down list to choose one of
the certificates for using. You have to configure one
certificate at least previously in Certificate Management
>> Local Certificate. Otherwise, the setting you choose
here will not be effective.
IPsec Security
Method
Medium - Authentication Header (AH) means data will be
authenticated, but not be encrypted. By default, this option
is active.
High - Encapsulating Security Payload (ESP) means
payload (data) will be encrypted and authenticated. You
may select encryption algorithm from Data Encryption
Standard (DES), Triple DES (3DES), and AES.
User Name
This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.
The length of the use name is limited to 11 characters.
Password
This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.
The length of the password is limited to 11 characters.
Remote Network IP
Please type one LAN IP address (according to the real
location of the remote host) for building VPN connection.
Remote Network
Mask
Please type the network mask (according to the real location
of the remote host) for building VPN connection.
3. After finishing the configuration, please click Next. The confirmation page will be shown
as follows. If there is no problem, you can click one of the radio buttons listed on the page
and click Finish to execute the next action.
Page 76
Vigor2760 Series User’s Guide
60
Available settings are explained as follows:
Item Description
Go to the VPN
Connection
Management
Click this radio button to access VPN and Remote
Access>>Connection Management for viewing VPN
Connection status.
Do another VPN
Server Wizard Setup
Click this radio button to set another profile of VPN Server
through VPN Server Wizard.
View more detailed
configuration
Click this radio button to access VPN and Remote
Access>>LAN to LAN for viewing detailed configuration.
Page 77
Vigor2760 Series User’s Guide
61
22..44 VVPPNN SSeerrvveerr WWiizzaarrdd
Such wizard is used to configure VPN settings for VPN server. Such wizard will guide to set
the LAN-to-LAN profile for VPN dial in connection (from client to server) step by step.
1. Open VPN and Remote Access>>VPN Server Wizard. The following page will appear.
Available settings are explained as follows:
Item Description
VPN Server Mode
Selection
Choose the direction for the VPN server.
Site to Site VPN – To set a LAN-to-LAN profile
automatically, please choose Site to Site VPN.
Remote Dial-in User –You can manage remote access by
maintaining a table of remote user profile, so that users can
be authenticated to dial-in via VPN connection.
Please choose a
LAN-to-LAN Profile
This item is available when you choose Site to Site VPN
(LAN-to-LAN) as VPN server mode. There are 32 VPN
profiles for users to set.
Page 78
Vigor2760 Series User’s Guide
62
Please choose a
Dial-in User
Accounts
This item is available when you choose Remote Dial-in
User (Teleworker) as VPN server mode. There are 32 VPN
tunnels for users to set.
Allowed Dial-in Type
This item is available after you choose any one of dial-in
user account profiles. Next, you have to select suitable
dial-in type for the VPN server profile. There are several
types provided here (similar to VPN Client Wizard).
Different Dial-in Type will lead to different configuration
page. In addition, adjustable items for each dial-in type will
be changed according to the VPN Server Mode (Site to Site
VPN and Remote Dial-in User) selected.
2. After making the choices for the server profile, please click Next. You will see different
configurations based on the selection you made.
Here we take the examples of choosing Site-to-Site VPN as the VPN Server Mode.
Page 79
Vigor2760 Series User’s Guide
63
When you check PPTP, you will see the following graphic:
When you check PPTP & IPsec & L2TP (three types) or PPTP & IPsec (two types) or
L2TP with Policy (Nice to Have/Must), you will see the following graphic:
Page 80
Vigor2760 Series User’s Guide
64
When you check IPsec, you will see the following graphic:
Available settings are explained as follows:
Item Description
Profile Name
Type a name for such profile. The length of the file is
limited to 10 characters.
User Name
This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.
The length of the name is limited to 11 characters.
Password
This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.
The length of the name is limited to 11 characters.
Pre-Shared Key
For IPsec/L2TP IPsec authentication, you have to type a
pre-shared key.
The length of the name is limited to 64 characters.
Confirm Pre-Shared
Key
Type the pre-shared key again for confirmation.
Digital Signature
(X.509)
Check the box of Digital Signature to invoke this function.
Peer ID – Choose the peer ID selection from the drop down
list.
Local ID – Choose Alternative Subject Name First or
Subject Name First.
Peer IP/VPN Client
IP
Type the WAN IP address or VPN client IP address for the
remote client.
Peer ID
Type the ID name for the remote client.
The length of the name is limited to 47 characters.
Page 81
Vigor2760 Series User’s Guide
65
Remote Network IP
Please type one LAN IP address (according to the real
location of the remote host) for building VPN connection.
Remote Network
Mask
Please type the network mask (according to the real location
of the remote host) for building VPN connection.
3. After finishing the configuration, please click Next. The confirmation page will be shown
as follows. If there is no problem, you can click one of the radio buttons listed on the page
and click Finish to execute the next action.
Available settings are explained as follows:
Item Description
Go to the VPN
Connection
Management
Click this radio button to access VPN and Remote
Access>>Connection Management for viewing VPN
Connection status.
Do another VPN
Server Wizard Setup
Click this radio button to set another profile of VPN Server
through VPN Server Wizard.
View more detailed
configuration
Click this radio button to access VPN and Remote
Access>>LAN to LAN for viewing detailed configuration.
Page 82
Vigor2760 Series User’s Guide
66
22..55 WWiirreelleessss WWiizzaarrdd
The wireless wizard allows you to configure settings specified for a host AP (for home use or
internal use for a company) and specified for a guest AP (for any wireless clients accessing
into Internet).
Follow the steps listed below:
1. Open Wireless Wizard.
2. The screen of wireless wizard will be shown as follows. This page will be used for internal
users in a company or your home.
Available settings are explained as follows:
Item Description
Name
Type the SSID name of this router. The default name is
defined with DrayTek. Change the name if required.
Mode
At present, the router can connect to 11b Only, 11n Only, 11g
Only, Mixed (11b+11g), Mixed (11g+11n), and Mixed
(11b+11g+11n) stations simultaneously. Simply choose Mix
(11b+11g+11n) mode.
Page 83
Vigor2760 Series User’s Guide
67
Channel
Means the channel of frequency of the wireless LAN. The
default channel is 6. You may switch channel if the selected
channel is under serious interference. If you have no idea of
choosing the frequency, please select Auto to let system
determine for you.
Password
The wireless mode offered by this wizard is WPA2/PSK.
The WPA encrypts each frame transmitted from the radio
using the key, which either PSK (Pre-Shared Key) entered
manually in this field below.
Either 8~63 ASCII characters, such as 012345678(or 64
Hexadecimal digits leading by 0x, such as
“0x321253abcde…”).
Next
Click it to get into the next setting page.
Cancel
Exit the wireless wizard without saving any changes.
3. After typing the required information, click Next. The settings in the page limit the
wireless station (guest) accessing into Internet but not being allowed to share the LAN
network and VPN connection.
Available settings are explained as follows:
Item Description
Enable/Disable
Click it to enable or disable settings in this page.
Name
Type the SSID name of this router. (SSID1)
Security Key
The wireless mode offered by this wizard is WPA2/PSK.
The WPA encrypts each frame transmitted from the radio
using the key, which either PSK (Pre-Shared Key) entered
Page 84
Vigor2760 Series User’s Guide
68
manually in this field below.
Either 8~63 ASCII characters, such as 012345678(or 64
Hexadecimal digits leading by 0x, such as
"0x321253abcde...").
Bandwidth Limit
It controls the data transmission rate through wireless
connection.
Total Upload – Check Enable and type the transmitting rate
for data upload. Default value is 30,000 kbps.
Total Download – Type the transmitting rate for data
download. Default value is 30,000 kbps.
Next
Click it to get into the next setting page.
Cancel
Exit the wireless wizard without saving any changes.
4. After typing the required information, click Next.
5. The following page will display the configuration summary for wireless setting.
6. Click Finish to complete the wireless settings configuration.
Page 85
Vigor2760 Series User’s Guide
69
22..66 VVooIIPP WWiizzaarrdd
Vigor router offers a quick method to configure settings for VoIP application. Follow the steps
listed below.
Note: This wizard is available for “V” model only.
1. Open Wizards>>VoIP Wizard.
2. The screen of VoIP Wizard will be shown as follows.
Available settings are explained as follows:
Item Description
Set VoIP service
provider domain
VoIP service provider - Use the drop down list to choose
the ISP which offers the VoIP service for your router.
SIP Port – Use the default setting (5060).
Set Account quickly
Account Number/Name – Type the account number/name
registered to your ISP.
Password – Type the password for the account registered to
your ISP.
Use the same Account as phone 1 – If you don’t need to
configure Phone 2 settings, simply check this box.
Next
Click it to get into the next setting page.
Page 86
Vigor2760 Series User’s Guide
70
Cancel
Click it to give up the quick start wizard.
3. After finished the settings above, click Next for viewing summary of such connection.
4. Click Finish. A page of VoIP Wizard Setup OK!!! will appear.
Page 87
Vigor2760 Series User’s Guide
71
22..77 RReeggiisstteerriinngg VViiggoorr RRoouutteerr
You have finished the configuration of Quick Start Wizard and you can surf the Internet at any
time. Now it is the time to register your Vigor router to MyVigor website for getting more
service. Please follow the steps below to finish the router registration.
1 Please login the web configuration interface of Vigor router by typing “admin/admin”
as User Name / Password.
2 Click Support Area>>Production Registration from the home page.
3 A Login page will be shown on the screen. Please type the account and password that
you created previously. And click Login.
Page 88
Vigor2760 Series User’s Guide
72
4 The following page will be displayed after you logging in MyVigor. From this page,
please click Add or Product Registration.
5 When the following page appears, please type in Nickname (for the router) and choose
the right registration date from the popup calendar (it appears when you click on the box
of Registration Date). After adding the basic information for the router, please click
Submit.
6 When the following page appears, your router information has been added to the
database.
7 Now, you have finished the product registration.
Page 89
Vigor2760 Series User’s Guide
73
8 After clicking OK, you will see the following page. Your router has been registered to
myvigor website successfully.
If you have not activated web content filter service by using Service Activation Wizard,
you can activate the service from this step. Please click the serial number link.
9 From the Device’s Service section, click the Trial.
10 In the following page, check the box of “I have read and accept the above Agreement”.
The system will find out the date for you to activate this version of service. Then, click
Next.
Page 90
Vigor2760 Series User’s Guide
74
11 When this page appears, click Register.
12 Wait for a moment until the following page appears.
13 Click Close.
Page 91
Vigor2760 Series User’s Guide
75
A
Addvvaanncceedd
C
Coonnffiigguurraattiioonn
This chapter will guide users to execute web configuration.
1. Open a web browser on your PC and type http://192.168.1.1. The window will ask for
typing username and password.
2. Please type “admin/admin” on Username/Password for administration operation.
Now, the Main Screen will appear. Note that different model will have different web pages.
33..11 WWAANN
Quick Start Wizard offers user an easy method to quick setup the connection mode for the
router. Moreover, if you want to adjust more settings for different WAN modes, please go to
WAN group.
33..11..11 BBaassiiccss ooff IInntteerrnneett PPrroottooccooll ((IIPP)) NNeettwwoorrkk
IP means Internet Protocol. Every device in an IP-based Network including routers, print
server, and host PCs, needs an IP address to identify its location on the network. To avoid
address conflicts, IP addresses are publicly registered with the Network Information Centre
(NIC). Having a unique IP address is mandatory for those devices participated in the public
network but not in the private TCP/IP local area networks (LANs), such as host PCs under the
management of a router since they do not need to be accessed by the public. Hence, the NIC
has reserved certain addresses that will never be registered publicly. These are known as
private IP addresses, and are listed in the following ranges:
From 10.0.0.0 to 10.255.255.255
From 172.16.0.0 to 172.31.255.255
From 192.168.0.0 to 192.168.255.255
WWhhaatt aarree PPuubblliicc IIPP AAddddrreessss aanndd PPrriivvaattee IIPP AAddddrreessss
Page 92
Vigor2760 Series User’s Guide
76
As the router plays a role to manage and further protect its LAN, it interconnects groups of
host PCs. Each of them has a private IP address assigned by the built-in DHCP server of the
Vigor router. The router itself will also use the default private IP address: 192.168.1.1 to
communicate with the local hosts. Meanwhile, Vigor router will communicate with other
network devices through a public IP address. When the data flow passing through, the
Network Address Translation (NAT) function of the router will dedicate to translate
public/private addresses, and the packets will be delivered to the correct host PC in the local
area network. Thus, all the host PCs can share a common Internet connection.
GGeett YYoouurr PPuubblliicc IIPP AAddddrreessss ffrroomm IISSPP
In ADSL deployment, the PPP (Point to Point)-style authentication and authorization is
required for bridging customer premises equipment (CPE). Point to Point Protocol over
Ethernet (PPPoE) connects a network of hosts via an access device to a remote access
concentrator or aggregation concentrator. This implementation provides users with significant
ease of use. Meanwhile it provides access control, billing, and type of service according to
user requirement.
When a router begins to connect to your ISP, a serial of discovery process will occur to ask for
a connection. Then a session will be created. Your user ID and password is authenticated via
PAP or CHAP with RADIUS authentication system. And your IP address, DNS server, and
other related information will usually be assigned by your ISP.
NNeettwwoorrkk CCoonnnneeccttiioonn bbyy 33GG UUSSBB MMooddeemm
For 3G mobile communication through Access Point is popular more and more, Vigor2760
adds the function of 3G network connection for such purpose. By connecting 3G USB Modem
to the USB port of Vigor2760, it can support HSDPA/UMTS/EDGE/GPRS/GSM and the
future 3G standard (HSUPA, etc). Vigor2760n with 3G USB Modem allows you to receive 3G
signals at any place such as your car or certain location holding outdoor activity and share the
bandwidth for using by more people. Users can use four LAN ports on the router to access
Internet. Also, they can access Internet via 802.11n wireless function of Vigor2760n, and
enjoy the powerful firewall, bandwidth management, VPN features of Vigor2760n series.
After connecting into the router, 3G USB Modem will be regarded as the third WAN port.
However, the original WAN1 and WAN2 still can be used and Load-Balance can be done in
the router. Besides, 3G USB Modem in WAN3 also can be used as backup device. Therefore,
when WAN1 and WAN2 are not available, the router will use 3.5G for supporting
automatically. The supported 3G USB Modem will be listed on DrayTek web site. Please visit
www.draytek.com for more detailed information.
Below shows the menu items for WAN.
Page 93
Vigor2760 Series User’s Guide
77
33..11..22 GGeenneerraall SSeettuupp
This section will introduce some general settings of Internet and explain the connection modes
for WAN1, WAN2 and WAN3 in details.
This router supports multiple-WAN function. It allows users to access Internet and combine
the bandwidth of the multiple WANs to speed up the transmission through the network. Each
WAN port can connect to different ISPs, Even if the ISPs use different technology to provide
telecommunication service (such as DSL, Cable modem, etc.). If any connection problem
occurred on one of the ISP connections, all the traffic will be guided and switched to the
normal communication port for proper operation. Please configure WAN1, WAN2, and
WAN3 settings.
This webpage allows you to set general setup for WAN1, WAN2, and WAN3 respectively. In
default, WAN2 is disabled. If you want to enable it, simply click the WAN2 link and select
Yes in the field of Enable.
Available settings are explained as follows:
Item Description
Index
Click the WAN interface link under Index to access into the
WAN configuration page.
Enable
V means such WAN interface is enabled and ready to be
used.
Physical Mode / Type
Display the physical mode and physical type of such WAN
interface.
Note: In default, each WAN port is enabled.
After finished the above settings, click OK to save the settings.
Page 94
Vigor2760 Series User’s Guide
78
WWAANN11 wwiitthh AADDSSLL//VVDDSSLL
Vigor router will detect the physical line is connected by ADSL or VDSL2 automatically.
Therefore, this page allows you to configure settings for ADSL and VDSL2 at one time. That
is, it is not necessary for you to configure different profile settings for ADSL and VDSL2
respectively.
Available settings are explained as follows:
Item Description
Enable
Choose Yes to invoke the settings for this WAN interface.
Choose No to disable the settings for this WAN interface.
Display Name
Type the description for such interface.
Physical Mode
Display the physical mode of such interface. If VDSL2 is
detected, this field will display “VDSL2”; if ADSL is
detected, it will display “ADSL”.
DSL Mode
Specify the physical mode (VDSL or ADSL) for such
router manually.
Physical Type
For such interface, no type can be selected.
DSL Modem Code
Choose the correct DSL modem code for ensuring the
network connection.
If you have no idea about the selection, simply choose
Page 95
Vigor2760 Series User’s Guide
79
Default or contact the dealer for assistance.
VLAN Tag insertion
(ADSL)
The settings configured in this field are available for ADSL.
Enable – Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets
on the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN1.
Disable – Disable the function of VLAN with tag.
Tag value – Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority – Type the packet priority number for such VLAN.
The range is from 0 to 7.
VLAN Tag insertion
(VDSL2)
The settings configured in this field are available for
VDSL2.
Enable – Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets
on the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN1.
Disable – Disable the function of VLAN with tag.
Tag value – Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority – Type the packet priority number for such VLAN.
The range is from 0 to 7.
After finished the above settings, click OK to save the settings.
Page 96
Vigor2760 Series User’s Guide
80
WWAANN22 wwiitthh EEtthheerrnneett
The physical LAN4 port can be treated as a WAN interface, named WAN2.
When WAN2 is enabled, WAN1 (DSL) will be disabled automatically.
Available settings are explained as follows:
Item Description
Enable
Choose Yes to invoke the settings for this WAN interface.
Choose No to disable the settings for this WAN interface.
Display Name
Type the description for such WAN interface.
Physical Mode
Display the physical mode of such WAN interface.
Physical Type
You can change the physical type for WAN2 or choose
Auto negotiation for determined by the system.
VLAN Tag insertion
Enable – Enable the function of VLAN with tag.
The router will add specific VLAN number to all packets on
the WAN while sending them out.
Please type the tag value and specify the priority for the
packets sending by WAN1.
Disable – Disable the function of VLAN with tag.
Tag value – Type the value as the VLAN ID number. The
range is form 0 to 4095.
Priority – Type the packet priority number for such VLAN.
WAN1
WAN3
WAN2
Page 97
Vigor2760 Series User’s Guide
81
The range is from 0 to 7.
After finished the above settings, click OK to save the settings.
WWAANN33 wwiitthh UUSSBB
To use 3G/4G network connection through 3G/4G USB Modem, please configure WAN3
interface.
Available settings are explained as follows:
Item Description
Enable
Choose Yes to invoke the settings for this WAN interface.
Choose No to disable the settings for this WAN interface.
Display Name
Type the description for such WAN interface.
Physical Mode
Display the physical mode of such WAN interface.
After finished the above settings, click OK to save the settings.
Page 98
Vigor2760 Series User’s Guide
82
33..11..33 IInntteerrnneett AAcccceessss
For the router supports multi-WAN function, the users can set different WAN settings (for
WAN1/WAN2/WAN3) for Internet Access. Due to different Physical Mode for WAN
interface, the Access Mode for these connections also varies. Refer to the following figures.
Available settings are explained as follows:
Item Description
Index
Display the WAN interface.
Display Name
It shows the name of the WAN1/WAN2/WAN3 that
entered in general setup.
Physical Mode
It shows the physical connection for
WAN1(ADSL/VDSL2) /WAN2 (Ethernet) /WAN3 (3G/4G
USB Modem) according to the real network connection.
Access Mode
Use the drop down list to choose a proper access mode. The
details page of that mode will be popped up. If not, click
Details Page for accessing the page to configure the
settings.
Details Page
This button will open different web page (based on IPv4)
Page 99
Vigor2760 Series User’s Guide
83
according to the access mode that you choose in WAN
interface.
Note that Details Page will be changed slightly based on
ADSL/VDSL2 physical mode specified on
WAN>>General Setup.
IPv6
This button will open different web page (based on Physical
Mode) to setup IPv6 Internet Access Mode for WAN
interface.
If IPv6 service is active on this WAN interface, the color of
“IPv6” will become green.
Advanced
This button allows you to configure DHCP client options.
DHCP packets can be processed by adding option number
and data information when such function is enabled and
configured.
Enable/Disable – Enable/Disable the function of DHCP
Option. Each DHCP option is composed by an option
number with data. For example,
Option number:100
Data: abcd
When such function is enabled, the specified values for
DHCP option will be seen in DHCP reply packets.
Interface – Specify the WAN interface(s) that will be
overwritten by such function. WAN4 ~ WAN6 can be
located under WAN>>Multi-PVC.
Option Number – Type a number for such function.
Note: If you choose to configure option 61 here, the
detailed settings in WAN>>Interface Access will be
overwritten.
DataType – Choose the type (ASCII or Hex) for the data to
be stored.
Data – Type the content of the data to be processed by the
function of DHCP option.
Page 100
Vigor2760 Series User’s Guide
84
DDeettaaiillss PPaaggee ffoorr PPPPPPooEE iinn WWAANN11 ((PPhhyyssiiccaall MMooddee:: VVDDSSLL22))
To choose PPPoE as the accessing protocol of the Internet, please select PPPoE from the
WAN>>Internet Access >>WAN1 page. The following web page will be shown.
Available settings are explained as follows:
Item Description
Enable/Disable
Click Enable for activating this function. If you click
Disable, this function will be closed and all the settings that
you adjusted in this page will be invalid.
ISP Access Setup
Enter your allocated username, password and authentication
parameters according to the information provided by your
ISP.
Username – Type in the username provided by ISP in this
field.
Password – Type in the password provided by ISP in this
field.
Index (1-15) in Schedule Setup - You can type in four sets
of time schedule for your request. All the schedules can be
set previously in Application >> Schedule web page and
you can use the number that you have set in that web page.
WAN Connection
Detection
Such function allows you to verify whether network
connection is alive or not through ARP Detect or Ping
Detect.
Mode – Choose ARP Detect or Ping Detect for the system
to execute for WAN detection.
Ping IP – If you choose Ping Detect as detection mode, you
have to type IP address in this field for pinging.
TTL (Time to Live) – Displays value for your reference.
Loading...