Page 1
Vigor2760 Series Quick Start Guide
i
Page 2
Vigor2760 Series Quick Start Guide
ii
Page 3
Vigor2760 Series Quick Start Guide
iii
Vigor2760 Series
High Speed VDSL2 Router
Quick Start Guide
Guide Version: 1.0
For updates and support, visit www.draytek.co.uk
May 2014 / Firmware V3.7.5.1
Note: Product specification is subject to continuous evolution which may
not always be reflected in current documentation. For the formal specification
of your product, please refer only to the web site at www.draytek.co.uk
Page 4
Page 5
Vigor2760 Series Quick Start Guide
i
Copyright Information
Copyright
Declarations
Copyright© 2014 All rights reserved. This publication contains information that
is protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
Microsoft & Windows are a registered trademarks of Microsoft Corp.
Apple, iOS and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks of their respective manufacturers.
Safety Instructions, Warranty & Updates
Safety Instructions
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized personnel. Do not try to open or repair the router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
Do not stack the router or obstruct its ventilation..
The router should be used within a temperature range of +5 to +40C and
not exposed to heat sources or direct sunlight.
Do not run any LAN cables outdoors or to external buildings.
Keep the packaging out of reach of children.
When you want to dispose of the router, please follow local regulations
on conservation of the environment.
W
arranty
We warrant to the original end user (purchaser) that the router will be free
from any defects in workmanship or materials for a period of two (2) years
from the date of purchase from the dealer. Please keep your purchase receipt
safely as proof of purchase. During the warranty period, and upon proof of
purchase, should the product have indications of failure due to faulty
workmanship and/or materials, we will, at our discretion, re pair or replace the
defective products or components, without charge for either parts or labour, to
whatever extent we deem necessary to re-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at
our discretion. This warranty will not apply if the product is modified,
misused, tampered with, damaged by an act of God, or subjected to
abnormal/unapproved working conditions. The warranty does not cover the
bundled or licensed software of other vendors. Def ect s which do not
significantly affect the usability of the product will not be covered by the
warranty. We reserve the right to revise the manual and online documentation
and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes. Warranty service
is ‘RTB’ (return to base), not advance replacement or on-site and in all cases
provided through the distribution chain through which the product was
supplied and only to the intended locale. You can subscribe to VigorCare
within 30 days of purchase – see www.draytek.co.uk/vigorcare
J
oin the UK
mailing list
Users in the UK & Ireland can sign up to our mailing list which goes out 4-6
times per year with products news, updates, hints & tips an d of fers. For
details, please visit www.draytek.co.uk/mailing-list
Fi
r
mware & Tools
Updates
Due to the continuous evolution of DrayTek technology and emerging risks,
router firmware updates may be issued. Please consult the DrayTek web site
for more information on newest firmware, tools and documents.
www.draytekco.uk
(For users and products in the UK/Ireland)
Page 6
Vigor2760 Series Quick Start Guide
ii
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product: Vigor2760 Series Router
DrayTek Corp. declares that Vigor2760 Series complies with R&TTE Directive 1999/5/EEC, the
requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC, EN55022/Class B and
EN55024/Class B and Low Voltage (LVD) Directive 2006/95/EC complying with EN60950-1.
This product is designed for POTS, xDSL and 2.4GHz WLAN network for UK/Ireland. Please refer to the
web site (www.draytek.co.uk
) for latest specification and compatibility for your product.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit to the the receiver.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
RRFF EExxppoossuurree WWaarrnniinngg
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
`` CCaauuttiioonn
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment including the usage on unauthorised accessories.
Please visit http://www.draytek.com/user/SupportDLRTTECE.php
#
Page 7
Vigor2760 Series Quick Start Guide
iii
TTaabbllee ooff CCoonntteennttss
1. Introduction ........................................................................................1
1.1 Front Panel & Connectors .............................................................................. 2
1.2 Package Contents (Accessories).................................................................... 5
2. Installing Yo ur Router ........................................................................6
2.1 Hardware Installation...................................................................................... 6
3. Quick Setup ........................................................................................8
3.1 Accessing the Web User Interface (WUI) ....................................................... 8
3.2 Configuring WAN1 for Internet Access ........................................................... 9
3.3 Configuring WAN2 for Internet Access ......................................................... 12
3.4 Configuring WAN3 for Internet Access ......................................................... 14
4. Troubleshooting...............................................................................15
4.1 Check the Hardware connection................................................................... 15
4.2 Check your computer’s Network Connection Settings.................................. 16
For Windows............................................................................................ 16
For Mac OS.............................................................................................. 18
4.3 Pinging the router from your computer ......................................................... 19
For Windows............................................................................................ 19
For Mac OS (Terminal)............................................................................ 19
4.4 Check the ISP Settings on the router............................................................ 20
4.5 Problems with 3G/4G Network Connection .................................................. 20
Check if the router’s USB LED is on........................................................ 20
USB LED lit but no network connection................................................... 20
3G/4G Connection Speed........................................................................ 21
4.6 Restoring back to Factory Default Settings................................................... 21
4.7 Getting further help....................................................................................... 23
5. Additional Feature Setup.................................................................23
6. Keep Up to Date with Our Mailing List ...........................................23
7. Firmware Updates............................................................................23
Page 8
Page 9
Vigor2760 Series Quick Start Guide
1
11.. IInnttrroodduuccttiioonn
The Vigor2760 series is a router/firewall supporting ADSL, VDSL or
Ethernet-fed WAN technologies, ideal to allow later migration or
standardization on a single model regardless of your Internet connectivity
The Vigor 2760 series includes 802.11n Wireless LAN (n models) with
multiple security methods to help protect your network. The Vigor 2760Vn
also includes phone ports for connectivity of a phone to make use of
Voice-over-IP (VoIP) services for low-cost calls over the Internet
(compatible SIP/VoIP provider required).
With the high throughput performance, Quality of Service assurance and
web content filtering features provided by the Vigor2760 series, you can
simultaneously use bandwidth-intensive applications, such as video
streaming, online gaming, and Internet telephony / access.
The Vigor2760 supports up to 2 outgoing (dial-out to HQ) VPN tunnels
using advanced protocols such as IPSec with AES/3DES for encryption and
MD5/SHA-1 for authentication allowing connectivity to your main office.
In addition, the Vigor 2760 series supports two USB interfaces for
connecting a shared USB printer, a USB memory device for sharing files or
compatible 3G/4G cellular dongle for Internet backup.
Page 10
Vigor2760 Series Quick Start Guide
2
11..11 FFrroonntt PPaanneell && CCoonnnneeccttoorrss
LED Status Explanation
Blinking The router is running normally.
ACT
Off The router is powered off.
On A PSTN phone call is active on a
connected telephone handset.
LINE
(Vigor 2760Vn only)
Off There is no active PSTN phone call.
On The phone on this port is off-hook.
Off The phone on this port is on-hook.
Phone1/Phone2
(Vigor 2760Vn only)
Blinking A phone call is ringing.
On (Green) The wireless access point is ready.
Blinking
(Green)
The data is transmitting via wireless
connection.
Blinking
(Orange)
Blinks with one second cycle for two
minutes. The WPS function is active.
Wireless LAN
On/Off/WPS
(Vigor 2760n and
Vigor 2760Vn only)
Off Wireless access is turned off.
On The xDSL port is connected.
Slow Blink The router is ready to connect.
xDSL (Green)
Fast Blink The router is trying to connect to
Internet or synchronize with the line.
On The port is connected.
~
LAN 1/2/3/4
Blinking Data is transmitting.
~
USB1/2
On A USB device is connected and active.
Page 11
Vigor2760 Series Quick Start Guide
3
Interface Description
PWR Connector for the power adapter.
I / O
Power switch. Turns the unit on or off.
Factory Reset Restore the default settings. Usage: Turn on the
router (ACT LED is blinking). Press gently and hold
for more than 5 seconds. When the ACT LED blinks
rapidly, release the button and the router will restart
with its factory default configuration.
WLAN
ON/OFF/WPS
(Vigor 2760n and
Vigor 2760Vn only)
WLAN ON/OFF - Press button to enable/disable.
WLAN WPS - Press this button for 2 seconds to
allow for client devices to connect through WPS.
VDSL/ADSL RJ-11 connector for ADSL or VDSL line
USB (1-2) Connector for USB storage, printer or 3G/4G
modem
LAN (1-4)
(or WAN2)
RJ-45 Gigabit Ethernet connectors for local network
devices. If WAN2 (Ethernet) is enabled, LAN Port 4
becomes WAN2 (and WAN1 is disabled).
Page 12
Vigor2760 Series Quick Start Guide
4
Analogue Line / Phone Ports (Vigor 2760Vn only)
On the Vigor 2760Vn, you can take advantage of VoIP using any provider
compatible with the ‘SIP’ protocol (such as www.draytel.org
). VoIP enables
low cost or free calls and gives you additional call capacity (like having two
extra phone lines). You can connect 2 phones to the router to make calls,
each of which can work independently to make or receive calls.
You can also connect the router to your analogue line so that calls can also
be received from or made via your analogue line.
Interface Description
Line Connector for PSTN (analogue/POTS line)
Phone1/Phone2 Connector for a regular analogue phone for VoIP
communication. The socket is RJ-11 type; two
adaptors to BT/UK type socket are included.
Emergency Services: For the Vigor 2760Vn, check if your
VoIP service provides emergency services access (999/112).
You may need a separate analogue phone/line or mobile phone
for use in emergency. In a power cut, Phone 1 will
automatically connect to your analogue line, if the line is
connected to your router’s Line port. Do not make test calls to
the emergency service but do test a regular outgoing call using
your analogue line (dial #0 to select).
Page 13
Vigor2760 Series Quick Start Guide
5
11..22 PPaacckkaaggee CCoonntteennttss ((AAcccceessssoorriieess))
Quick Start Guide
CD (Contains manual)
RJ-45 Cable (Ethernet)
2 x Antennae (n models)
RJ-11 xDSL Line Cable
UK Power Adapter (PSU)
The Vigor 2760 router should only be used with the supplied PSU.
Operation with any other PSU may cause product malfunction or damage the
product and will invalidate your manufacturer’s warranty. If you lose your
PSU, use a genuine replacement from your DrayTek dealer.
For the Vigor 2760Vn model, you will additionally have two RJ11-BT
adaptors (to plug in phones) and an RJ11-BT plug cable, for connecting to
the analogue phone line for POTS (landline) voice calls.
Page 14
Vigor2760 Series Quick Start Guide
6
22.. IInnssttaalllliinngg YYoouurr RRoouutteerr
This section will guide you to install the router including hardware
connection and configuring the router’s settings through your web browser.
Firstly, be sure of what type of Internet connection you have:
Connection Port Description
ADSL WAN1
(RJ-11)
ADSL/ADSL2+ Service
VDSL WAN1
(RJ-11)
VDSL Service (FTTC/BT Infinity™).
Some ISPs (incorrectly) call this ‘fibre broadband’
Ethernet WAN2
(RJ-45)
If your Internet comes in via another
modem or other RJ-45 connection you can
use WAN2 instead of xDSL.
3G/4G Modem WAN3
(USB)
Using a compatible modem, you can use
3G/4G networks for backup (failover) to
your primary Internet connection. Check
for a list of compatible modems.
Note: ‘xDSL’ means either ADSL or VDSL. Several ISPs refer to their
VDSL service as ‘Fibre’ even though it’s delivered to you by copper wires to
your regular phone socket. Actual Fibre To The Premises (FTTP) is
relatively rare in the UK so most ISPs really mean copper/VDSL (Fibre To
The street Cabinet). The Vigor2760 is not compatible with actual fibre.
22..11 HHaarrddwwaarree IInnssttaallllaattiioonn
1. Connect the xDSL interface to the external xDSL splitter (microfilter)
with an xDSL line cable. With the Vigor2760Vn, also connect the Line
interface to the phone port on the xDSL splitter.
2. Connect Port 1 of the 4-port LAN switch to your computer with the
supplied RJ-45 cable. The router allows you to connect up to 4 PCs
directly (or 3 if you are using WAN2).
Page 15
Vigor2760 Series Quick Start Guide
7
3. If required, connect the Phone ports to a regular analogue telephone (for
Vn model only). Cordless DECT base stations are also compatible.
4. Connect the antennae to the router for Vigor2760 series (for n models
only). Attach them firmly but do not over-tighten.
5. Connect the power cord to the power port. Plug the PSU into the mains
wall outlet.
6. Turn on the router (the power switch is on the rear of the router).
7. Check the ACT and DSL, LAN LEDs to assure network connection.
Wireless Connection: If you have a Vigor 2760n or Vigor
2760Vn then you can connect to it from any wireless-equipped
device (PC, tablet etc.). The default SSID (network name) and
encryption password is printed on the bottom of your router.
Page 16
Vigor2760 Series Quick Start Guide
8
33.. QQuuiicckk SSeettuupp
33..11 AAcccceessssiinngg tthhee WWeebb UUsseerr IInntteerrffaaccee ((WWUUII))
1. Make sure your PC connects to the router correctly.
Normally, your computer will get its IP address dynamically from
the router (using ‘DHCP’), otherwise you must set the PCs IP
address to be in the same IP subnet as the router (e.g.
192.168.1.2).
The default IP address of the Vigor 2760 router
is 192.168.1.1.
2. Open a web browser on your PC and type http://192.168.1.1.
3. The following prompt will ask for the router’s username and password.
The default is “admin/admin” for Username/Password. The click Login
to open the web user interface (WUI).
Note: The default password of ‘admin’ should be changed at
your earliest opportunity (from the router’s system maintenance
menu), but don’t forget what you change it to otherwise you
will not be able to access the router’s configuration/WUI.
Page 17
Vigor2760 Series Quick Start Guide
9
The web interface that you see will vary depending on your exact model,
specification and firmware version in use. The dashboard gives you a live
snapshot of the current router and ports’ status.
33..22 CCoonnffiigguurriinngg WWAANN11 ffoorr IInntteerrnneett AAcccceessss
1. Select WAN>>General Setup. The below menu will appear:
Page 18
Vigor2760 Series Quick Start Guide
10
2. Click on the WAN1 link to open the following page:
3. Ensure that WAN1 interface is enabled (Enable:Yes). Set ‘Display
Name’ to your ISP’s name (e.g. BT, Sky, TalkTalk etc.). For the UK,
other default settings should be correct. Click OK to save/exit.
4. Open WAN>>Internet Access.
Page 19
Vigor2760 Series Quick Start Guide
11
5. Click the Details Page button for WAN1. Depending on your your ISP,
click either the PPPoE/PPPoA, MPoA/Static or Dynamic tab:
6. The PPPoE/PPPoA tab and the default settings are appropriate for
nearly all ISPs in the UK.
7. Users in Ireland may have different settings requirements. For
VDSL/FTTC users may need a VLAN tag of 10 (see point 2 above) and
for ADSL, use PPPoE/LLC with VPI/VCI settings of 8 and 35 (check
with your ISP for the latest settings).
8. Sky Broadband is one ISP which does vary; it may use the DHCP
method and require setting of the DHCP Option parameters; please refer
to specific help guides if you are using Sky (or former O2/Be).
9. Enter the ISP’s name and username/password in the boxes shown at the
top right of the above image.
10. Click OK to save. The router will restart to activate the settings and you
should then be online to the Internet.
Page 20
Vigor2760 Series Quick Start Guide
12
33..33 CCoonnffiigguurriinngg WWAANN22 ffoorr IInntteerrnneett AAcccceessss
The WAN2 port supports connections where there is Ethernet presentation
from the ISP supplied modem or Internet connection instead of xDSL.
WAN2 uses the physical port normally designated as LAN4.
If WAN2 is used then WAN1 will be disabled and vice versa. To setup the
Vigor 2760 to connect via WAN2 then please follow the steps below:
1. Open WAN >> General Setup.
2. Click the WAN2 link to open the following page:
3. Enable WAN2 (Enable:Yes), give the connection a display name (e.g.
your ISP’s name) and click OK to save and exit.
Page 21
Vigor2760 Series Quick Start Guide
13
4. Open the menu WAN>>Internet Access.
5. Click the Details Page button for WAN2. Depending on the information
supplied by your ISP, enable PPPoE, Static or Dynamic IP:
6. Fill in the information provided by your ISP. If you are using DHCP, you
may not need to change any settings. For PPPoE, you will need to set
your username and password. Click OK to save the settings and exit.
7. The router will restart to activate the settings and you should then be
online to the Internet.
Page 22
Vigor2760 Series Quick Start Guide
14
33..44 CCoonnffiigguurriinngg WWAANN33 ffoorr IInntteerrnneett AAcccceessss
WAN3 uses your USB port and supports an optional 3G/4G USB modem for
backup (automatic failover) to your primary Internet connection. Check for
the latest list of compatible USB modems.
1. In the router’s web interface, go to the WAN>Internet Access menu and
set WAN3 to 34/4G modem, then click on the adjacent Details Page
button as shown below:
2. In most cases, you only need to check the Enable button shown below
and set the appropriate APN name (and press Apply) for your ISP. Some
3G/4G ISPs use a username and password (often a generic one) but others
require that you leave the fields blank, or don’t care:
Page 23
Vigor2760 Series Quick Start Guide
15
44.. TTrroouubblleesshhoooottiinngg
If you cannot access the Internet after installing and configuring the router,
follow sections below to check your basic installation status stage by stage.
Check the hardware status is OK.
Check the network connection settings on your computer are OK.
Pinging the router from your computer.
Checking if the ISP settings are OK
Reset back to factory default setting if necessary.
If things are still not okay, it’s time to contact your dealer or DrayTek
support for more advanced help and troubleshooting (see later).
44..11 CChheecckk tthhee HHaarrddwwaarree ccoonnnneeccttiioonn
1. If no LEDs are lit, ensure the router is connected to the power supply
and turned on. Check that ACT LED blinks once per second.
2. If you are using ADSL/VDSL then check the xDSL LED on the front
panel. It should be lit steadily. If it is flashing quickly, the router is still
attempting synchonisation. If it is blinking slowly, it has not detected
any xDSL line. Ensure that the RJ11 cable is connected to the DSL port
and to the xDSL line (splitter/microfilter) correctly. Ensure that WAN1
is enabled (see earlier setup sections).
3. For initial configuration, we recommend using a wired (Ethernet/RJ-45)
connection. The corresponding LAN port LED (1-4) should be lit.
4. For wireless connections, the default SSID (network name) and WPA2
encryption key is printed on the bottom of the router.
5. If you can access the router web interface’s ‘Dashboard’ it gives you a
realtime indication of the router status and WAN status.
Page 24
Vigor2760 Series Quick Start Guide
16
44..22 CChheecckk yyoouurr ccoommppuutteerr’’ss NNeettwwoorrkk CCoonnnneeccttiioonn
SSeettttiin
nggss
Your computer may have the wrong network connection settings.
FFoorr WWiinnddoowwss
The examples shown are based on Windows 7. For examples on
other operating systems, please refer to support notes on our web
site.
1. Go to Control Panel and then double-click on Network and Sharing
Center.
2. Click on Local Area Connection and then select Properties (varies
according to O/S):
Page 25
Vigor2760 Series Quick Start Guide
17
3. Select Internet Protocol (TCP/IP) and then click Properties.
4. Ensure that Obtain an IP address automatically and Obtain DNS
server address automatically are selected.
Page 26
Vigor2760 Series Quick Start Guide
18
FFoorr MMaacc OOSS
1. Double click on the current used Mac OS on the desktop.
2. Open the Application folder and get into Network.
3. On the Network screen, select Using DHCP from the drop down list of
Configure IPv4.
Page 27
Vigor2760 Series Quick Start Guide
19
44..33 PPiinnggiinngg tthhee rroouutteerr ffrroomm yyoouurr ccoommppuutteerr
The default gateway IP address of the router is 192.168.1.1. You can use
“ping” to check if your PC can reach the router. Your PC should receive a
ping reply from the router at 192.168.1.1.
FFoorr WWiinnddoowwss
1. For Windows 2000/XP/Vista/7/8, open the Command Prompt window
(Press the Windows Key+R simultaneously) and type cmd (and press
Enter). Press Enter. The ‘DOS’ command prompt window appears:
2. Type ping 192.168.1.1 and press Enter. If the link is OK, you’ll get a
reply like “Reply from 192.168.1.1:bytes=32 time<1ms TTL=255”..
3. If the reply line does not appear, please check the IP address setting of
your computer.
FFoorr MMaacc OOSS ((TTeerrmmiinnaall))
1. Double click on the current used Mac OS on the desktop.
2. Open the Application folder and get into Utilities.
3. Double click Terminal. The Terminal window will appear.
4. Type ping 192.168.1.1 and press [Enter]. If the link is OK you will get a
reply like “64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=30
ms”.
Page 28
Vigor2760 Series Quick Start Guide
20
44..44 CChheecckk tthhee IISSPP SSeettttiinnggss oonn tthhee rroouutteerr
Open WAN>>Internet and check that the ISP settings are set correctly.
44..55 PPrroobblleemmss wwiitthh 33GG//44GG NNeettwwoorrkk CCoonnnneeccttiioonn
CChheecckk iiff tthhee rroouutteerr’’ss UUSSBB LLEEDD iiss oonn
You have to wait at least 15 seconds after inserting the 3G/4G USB modem
into your Vigor 2760. Synchronization and connection to the network can
take up to 1 minute. The router’s USB LED will light to indicate that the
USB Modem is active. If the USB LED is not lit, remove and re-insert the
modem. If it still fails, restart the Vigor 2760 (turn off then on again).
UUSSBB LLEEDD l
liitt bbuutt nnoo nneettwwoorrkk ccoonnnneeccttiioonn
Check the PIN Code of SIM card is disabled or not. Please use the modem’s
PC utility to disable PIN code. Ensure that you have used the correct APN
name for your 3G/4G ISP. Check with the web site or support department
that your modem type is supported.
Page 29
Vigor2760 Series Quick Start Guide
21
33GG//44GG CCoonnnneeccttiioonn SSppeeeedd
Connect your 3G/4G USB Modem to a PC directly to test or compare the
connection speed. In addition, please refer to the manual of 3G USB Modem
for LED Status to check that it’s using the right connection mode (e.g.
HSDPA mode and not a slower mode). Try different positions for the
modem for best signal reception (you can use a USB extension lead, max
2M). Some 3G/4G USB modems may draw a lot of current so a powered
USB hub may be necessary.
44..66 RReessttoorriinngg bbaacckk ttoo FFaaccttoorryy DDeeffaauulltt SSeettttiinnggss
Sometimes, an incorrect configuration necessitates returning to the default
settings (as it was when it came from the factory).
Warning: After resetting to factory default settings, you will
lose all existing router settings. Ensure beforehand that you have
recorded all necessary settings to allow reconfiguration.
FFaaccttoorryy RReesseett ffrroomm tthhee WWeebb IInntteerrffaaccee
You can reset the router to factory default via the Web interface.
Open System Maintenance>> Reboot System. The following screen will
appear. Choose Using factory default configuration and click OK. The
router will reboot and then be at default factory settings.
Page 30
Vigor2760 Series Quick Start Guide
22
FFaaccttoorryy RReesseett UUssiinngg tthhee HHaarrddwwaarree RReesseett BBuuttttoonn
Whilst the router is running (ACT LED blinking), press the Factory Reset
button and hold it for more than 5 seconds. When you see the ACT LED
blinking rapidly, release the button. Then, the router will restart with the
default configuration.
After restoring the factory default settings, you can re-configure the settings
for the router again from scratch.
After a factory reset, the router’s default IP address is 192.168.1.1 again and
the admin username/password returns to admin/admin.
Page 31
Vigor2760 Series Quick Start Guide
23
44..77 GGeettttiinngg ffuurrtthheerr hheellpp
If the router still does not appear to be operating correctly or you cannot get
online to the Internet, please visit our web sites for further troubleshooting
advice or to contact our support technicians. Users in the UK/Ireland using
qualifying products should visit http://www.draytek.co.uk/support
for
options including email support, telephone support, knowledgebase and UK
user support forums.
If you are outside
of the UK/Ireland, please contact your own supplier,
support@draytek.com
or visit www.draytek.com/support
For warranty service, in the first instance, please contact the appropriate
support service as above. You should keep your proof of purchase safely in
case warranty service is required.
55.. AAddddiittiioonnaall FFeeaattuurree SSeettuupp
This is a quick setup guide to get you online with your new router. Your
Vigor 2760 series router is capable of very much more and has a plethora of
other features. These are covered in the main user manual (available on the
CD or the web site) and also the online knowledgebase.
66.. KKeeeepp UUpp ttoo DDaattee wwiitthh OOuurr MMaaiilliinngg LLiisstt
Now that your have your DrayTek product, you should keep up to date with
product updates (firmware) and other product news, advice or offers for
users. Users in the UK/Ireland can subscribe to our mailing list. For details
please see www.draytek.co.uk/mailing-list
. In other countries, please contact
your local distributor/supplier for local options.
77.. FFiirrmmwwaarree UUppddaatteess
Firmware updates for your product ensure that you have the latest set of
features, security updates and improvements for your product. Users in the
UK/Ireland can download these from www.draytek.co.uk/support
Please note that if your Vigor 2760 product has firmware version 1.x.x or
earlier then it can only update to later 1.x.x firmware. If your Vigor 2760 has
firmware version 3.7.5 or later (‘Delight/DrayOS’ hardware) then you can
upgrade to any compatible later firmware. You cannot use Delight/DrayOS
firmware on original (classic) Vigor 2760 hardware or vice-versa. This quick
setup guide applies only to DrayOS/Delight hardware/firmware.
Loading...