DrayTek Vigor2130n User Manual

Vigor2130 Series

High Speed Gigabit Router

User’s Guide

Version: 1.2

Firmware Version: V1.3.0.1

Date: 29/04/2010

Vigor2130 Series User’s Guide

Trademarks

Copyright 2010 All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.

The following trademarks are used in this document:

z Microsoft is a registered trademark of Microsoft Corp. z Windows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are

trademarks of Microsoft Corp.

z Apple and Mac OS are registered trademarks of Apple Inc. z Other products may be trademarks or registered trademarks of their respective

manufacturers.

Safety Instructions and Approval

Safety Instructions

Warranty

z Read the installation guide thoroughly before you set up the router. z The router is a complicated electronic unit that may be repaired only be

authorized and qualified personnel. Do not try to open or repair the router yourself.

z Do not place the router in a damp or humid place, e.g. a bathroom. z The router should be used in a sheltered area, within a temperature range of +5 to

+40 Celsius.

z Do not expose the router to direct sunlight or other heat sources. The housing and

electronic components may be damaged by direct sunlight or heat sources.

z Do not deploy the cable for LAN connection outdoor to prevent electronic shock

hazards.

z Keep the package out of reach of children. z When you want to dispose of the router, please follow local regulations on

conservation of the environment. We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to re vi se the ma nual and onli ne documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

Be a Registered Owner

Firmware & Tools Updates

Vigor2130 Series User’s Guide

Web registration is preferred. You can register your Vigor router via http://www.draytek.com.

Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents.

http://www.draytek.com

iii

European Community Declarations

Manufacturer: DrayTek Corp.

Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303

Product: Vigor2130 Series Router DrayTek Corp. declares that Vigor2130 Series of routers are in compliance with the following essential

requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by

complying with the requirements set forth in EN55022/Class B and EN55024/Class B. The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the

requirements set forth in EN60950-1.

Regulatory Information

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisi o n recept i on , whi ch can be determined by turning the equipment of f and on, the use is encouraged to try to correct the interference by one of the following measures:

z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different form that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device may accept any interference received, including interference that may cause undesired operation.

Please visit http://www.draytek.com/user/AboutRegulatory.php

This product is designed for 2.4GHz WLAN network throughout the EC region and Switzerland with restrictions in France. Please see the user manual for the applicable networks on your product.

Vigor2130 Series User’s Guide

TTaabbllee ooff CCoonntteennttss

Preface ...............................................................................................................1

1.1 Web Configuration Buttons Explanation................................................................................. 1

1.2 LED Indicators and Connectors.............................................................................................. 2

1.2.1 For Vigor2130................................................................................................................... 2

1.2.2 For Vigor2130n................................................................................................................. 4

1.2.3 For Vigor2130Vn............................................................................................................... 6

1.3 Hardware Installation .............................................................................................................. 8

Stand Installation....................................................................................................................... 9

1.4 Printer Installation ................................................................................................................. 10

Configuring Basic Settings ............................................................................15

2.1 Two-Level Management........................................................................................................15

2.2 Accessing Web Page............................................................................................................ 15

2.3 Changing Password.............................................................................................................. 16

2.4 Quick Start Wizard................................................................................................................ 18

2.4.1 Setting up the Password................................................................................................. 18

2.4.2 Setting up the Time Zone............................................................................................... 19

2.4.3 Setting up the Internet Connection................................................................................. 19

2.4.4 Setting up the Wireless Connection ............................................................................... 24

2.4.5 Saving the Wizard Configuration.................................................................................... 29

2.5 Online St atus......................................................................................................................... 29

2.6 Saving Configuration............................................................................................................. 30

U s e r M o d e O p e r a t i o n............................................................................................31

3.1 WAN...................................................................................................................................... 31

3.1.1 Internet Access............................................................................................................... 33

3.1.2 Ports................................................................................................................................ 39

3.1.3 3G Backup...................................................................................................................... 40

3.2 LAN ....................................................................................................................................... 41

3.2.1 General Setup................................................................................................................. 44

3.2.2 Ports................................................................................................................................ 45

3.2.3 MAC Address Table........................................................................................................ 47

3.2.4 VLAN............................................................................................................................... 48

3.2.5 Monitor Port.................................................................................................................... 49

3.2.6 Static Route.................................................................................................................... 50

3.2.7 Bind IP to MAC............................................................................................................... 51

3.3 NAT ....................................................................................................................................... 53

3.3.1 Hardware NAT................................................................................................................ 53

Vigor2130 Series User’s Guide

3.3.2 Open Ports...................................................................................................................... 54

3.3.3 DMZ Host........................................................................................................................ 55

3.4 Bandwidth Management....................................................................................................... 56

3.4.1 Session Limit .................................................................................................................. 56

3.4.2 Bandwidth Limit .............................................................................................................. 57

3.4.3 Port Rate Control............................................................................................................ 59

3.4.4 QoS Control List ............................................................................................................. 59

3.4.5 Ports Priority................................................................................................................... 64

3.4.6 QoS Statistics................................................................................................................. 65

3.5 Applications........................................................................................................................... 67

3.5.1 Dynamic DNS................................................................................................................. 67

3.5.2 Schedule......................................................................................................................... 68

3.5.3 IGMP Snooping ..............................................................................................................70

3.5.4 IGMP Status ................................................................................................................... 70

3.5.5 UPnP Configuration........................................................................................................71

3.5.6 Wake On LAN................................................................................................................. 72

3.6 Wireless LAN ........................................................................................................................ 73

3.6.1 Basic Concepts............................................................................................................... 73

3.6.2 General Setup................................................................................................................. 75

3.6.3 Access Control................................................................................................................ 80

3.6.4 Station List...................................................................................................................... 81

3.6.5 Access Point Discovery.................................................................................................. 82

3.7 USB Application.................................................................................................................... 82

3.7.1 USB General Settings..................................................................................................... 82

3.7.2 FTP User Management .................................................................................................. 83

3.7.3 Disk Status...................................................................................................................... 84

3.7.4 Disk Shares .................................................................................................................... 84

3.8 IPv6....................................................................................................................................... 86

3.8.1 IPv6 WAN Setup............................................................................................................. 86

3.8.2 IPv6 LAN Setup.............................................................................................................. 90

3.8.3 IPv6 Firewall Setup......................................................................................................... 91

3.8.4 IPv6 Routing................................................................................................................... 93

3.8.5 IPv6 Neighbour............................................................................................................... 94

3.8.6 IPv6 TSPC Status........................................................................................................... 94

3.9 User....................................................................................................................................... 97

3.9.1 User Configuration.......................................................................................................... 97

3.10 System Maintenance........................................................................................................... 98

3.10.1 System Status............................................................................................................... 98

3.10.2 TR069......................................................................................................................... 100

3.10.3 User Password ........................................................................................................... 101

3.10.4 Configuration Backup ................................................................................................. 102

3.10.5 Syslog / Mail Alert.......................................................................................................104

3.10.6 Time and Date............................................................................................................ 106

3.10.7 Management............................................................................................................... 107

3.10.8 Reboot System........................................................................................................... 108

3.10.9 Firmware Upgrade...................................................................................................... 108

A d m i n M o d e O p e r a t i o n.......................................................................................109

4.1 WAN.................................................................................................................................... 109

Vigor2130 Series User’s Guide

4.1.1 Internet Access.............................................................................................................111

4.1.2 Ports.............................................................................................................................. 117

4.1.3 3G Backup.................................................................................................................... 118

4.2 LAN ..................................................................................................................................... 120

4.2.1 General Setup............................................................................................................... 122

4.2.2 Ports.............................................................................................................................. 123

4.2.3 MAC Address Table...................................................................................................... 125

4.2.4 VLAN............................................................................................................................. 126

4.2.5 Monitor Port.................................................................................................................. 127

4.2.6 Static Route.................................................................................................................. 127

4.2.7 Bind IP to MAC............................................................................................................. 129

4.3 NAT .....................................................................................................................................130

4.3.1 Hardware NAT..............................................................................................................131

4.3.2 Open Ports.................................................................................................................... 131

4.3.3 DMZ Host...................................................................................................................... 133

4.4 Firewall................................................................................................................................ 134

4.4.1 DoS Defense ................................................................................................................ 134

4.4.2 Ports Configuration....................................................................................................... 135

4.4.3 Access Control List....................................................................................................... 137

4.5 Bandwidth Management ..................................................................................................... 149

4.5.1 Session Limit ................................................................................................................ 149

4.5.2 Bandwidth Limit ............................................................................................................150

4.5.3 Port Rate Control.......................................................................................................... 152

4.5.4 QoS Control List ........................................................................................................... 152

4.5.5 Ports Priority................................................................................................................. 157

4.5.6 QoS Statistics............................................................................................................... 158

4.6 Applications.........................................................................................................................160

4.6.1 Dynamic DNS............................................................................................................... 160

4.6.2 Schedule....................................................................................................................... 161

4.6.3 IGMP Snooping ............................................................................................................163

4.6.4 IGMP Status ................................................................................................................. 163

4.6.5 UPnP Configuration...................................................................................................... 164

4.6.6 Wake On LAN............................................................................................................... 166

4.7 VPN and Remote Access.................................................................................................... 166

4.7.1 Remote Access Control................................................................................................ 167

4.7.2 PPTP Remote Dial-in.................................................................................................... 168

4.7.3 IPSec Remote Dial-in ................................................................................................... 169

4.7.4 Remote Dial-in Status................................................................................................... 171

4.7.5 LAN to LAN................................................................................................................... 172

4.8 Wireless LAN ...................................................................................................................... 175

4.8.1 Basic Concepts............................................................................................................. 175

4.8.2 General Setup............................................................................................................... 176

4.8.3 Access Control.............................................................................................................. 182

4.8.4 Station List.................................................................................................................... 182

4.8.5 Access Point Discovery................................................................................................ 183

4.9 USB Application.................................................................................................................. 184

4.9.1 USB General Settings................................................................................................... 184

4.9.2 FTP User Management ................................................................................................ 184

4.9.3 Disk Status.................................................................................................................... 185

4.9.4 Disk Shares .................................................................................................................. 186

4.10 IPv6................................................................................................................................... 187

Vigor2130 Series User’s Guide

vii

4.10.1 IPv6 WAN Setup......................................................................................................... 187

4.10.2 IPv6 LAN Setup.......................................................................................................... 191

4.10.3 IPv6 Firewall Setup..................................................................................................... 192

4.10.4 IPv6 Routing............................................................................................................... 195

4.10.5 IPv6 Neighbour........................................................................................................... 196

4.10.6 IPv6 TSPC Status....................................................................................................... 196

4.1 1 User................................................................................................................................... 199

4.11.1 User Configuration...................................................................................................... 199

4.12 System Maintenance......................................................................................................... 201

4.12.1 System Status............................................................................................................. 201

4.12.2 TR-069........................................................................................................................ 202

4.12.3 System Password....................................................................................................... 204

4.12.4 User Password ........................................................................................................... 204

4.12.5 Configuration Backup ................................................................................................. 205

4.12.6 Syslog/Mail Alert.........................................................................................................207

4.12.7 Time and Date............................................................................................................ 209

4.12.8 Management............................................................................................................... 210

4.12.9 Reboot System........................................................................................................... 211

4.12.10 Firmware Upgrade.................................................................................................... 211

4.13 Diagnostics........................................................................................................................ 212

4.13.1 Ping............................................................................................................................. 212

4.13.2 Routing Table ............................................................................................................. 213

4.13.3 System Log................................................................................................................. 214

4.13.4 Traffic Overview.......................................................................................................... 214

4.13.5 Detailed Statistics....................................................................................................... 215

4.13.6 MAC Address Table.................................................................................................... 217

4.13.7 DHCP Table................................................................................................................ 219

4.13.8 Data Flow Monitor....................................................................................................... 220

4.13.9 Ports State.................................................................................................................. 221

Trouble Shooting...........................................................................................223

5.1 Checking If the Hardware Status Is OK or Not....................................................................223

5.2 Checking If the Network Connection Settings on Your Computer Is OK or Not................. 224

5.3 Pinging the Router from Your Computer............................................................................. 226

5.4 Checking If the ISP Settings are OK or Not........................................................................ 227

5.5 Forcing Vigor Router into TFTP Mode for Performing the Firmware Upgrade................... 229

5.6 Backing to Factory Default Setting If Necessary ................................................................ 232

5.7 Contacting Your Dealer....................................................................................................... 233

viii

Vigor2130 Series User’s Guide

Prreeffaaccee

The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be greater than 900Mbps almost.

With the development of NGN (Next Generation Network), you may recently hear the news about FTTx deployment in your local area or even have already subscribed the unbundling last mile service (e.g. VDSL2) from local ITSP for FTTx. As adopting FTTx, the main question for end users is whether your legacy router could fully utilize its bandwidth or not.

For example, you purchase a 120 Mbps Internet connection from your ISP but your existing router cannot support 90 Mbps throughput. That’s why DrayTek launches Vigor 2130 series – High speed Gigabit router, perfectly complied with VDSL2 environment including Vigor2130, Vigor2130n and Vigor2130Vn for speed-wanted customers. With high throughput performance and secured broadband connectivity provided by Vigor 2130 series, you can simultaneously engage these bandwidth-intensive applications, such as high-definition video streaming, online gaming, and Internet telephony / access.

11..11 WWeebb CCoonnffiigguurraattiioonn BBuuttttoonnss EExxppllaannaattiioonn

Several main buttons appeared on the web pages are defined as the following:

Save and apply current settings.

Cancel current settings and recover to the previous saved settings.

Clear all the selections and parameters settings, including selection from

drop-down list. All the values must be reset with factory default settings.

Add new settings for specified item.

Edit the settings for the selected item.

Delete the selected item with the corresponding settings.

Note: For the other buttons shown on the web pages, please refer to Chapter 4 for detailed explanation.

Vigor2130 Series User’s Guide

11..22 LLEEDD IInnddiiccaattoorrss aanndd CCoonnnneeccttoorrss

Before you use the Vigor router, please get acquainted with the LED indicators and connectors first.

11..22..11 FFoorr VViiggoorr22113300

LED Status Explanation

ACT

(Activity)

WAN

LAN 1/2/3/4

VPN On The VPN tunnel is active. QoS

DoS

Blinking The router is powered on and running

Off The router is powered off. On Hardware NAT is enabled. HPA Off Hardware NAT is disabled. On (Orange) The port is connected with 100Mbps. On (Green) The port is connected with 1000Mbps. Off The port is disconnected. Blinking It will blink while transmitting data. On (Orange) The port is connected with 100Mbps. On (Green) The port is connected with 1000Mbps. Off The port is disconnected. Blinking The data is transmitting. On A USB device is connected and active.USB1/2 Blinking The data is transmitting.

On The QoS function is active. On The DoS/DDoS function is active.

Blinking It will blink while detecting an attack.

normally.

Interface Description

WAN Connector for accessing the Internet. LAN

(1/2/3/4) USB

(1/2)

Connectors for local networked devices.

Connector for USB storage device (Pen Driver/Mobile HD) or printer or 3G backup.

Vigor2130 Series User’s Guide

Interface Description

Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press

the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.

PWR Connector for a power adapter. ON/OFF

Power Switch.

Vigor2130 Series User’s Guide

11..22..22 FFoorr VViiggoorr22113300nn

LED Status Explanation

ACT (Activity)

WAN

LAN 1/2/3/4

VPN On The VPN tunnel is active. QoS

WPS Button

Interface Description

WLAN

WAN Connector for accessing the Internet. LAN

(1/2/3/4) USB (1/2) Connector for USB storage (Pen Driver /Mobile HD) or

Blinking The router is powered on and running

normally.

On The QoS function is active. On Wireless access point is ready. WLAN

Blinking It will blink while wireless traffic goes

through.

On Press this button for 2 seconds to wait

for client device making network connection through WPS. When the LED lights up, the WPS connection

will be on. Off The WPS is off. Blinking Waiting for wireless client sending

requests for connection about two

minutes.

Press the button once to enable (WLAN LED on) or disable (WLAN LED off) wireless connection.

Connectors for local networked devices.

printer.

Vigor2130 Series User’s Guide

Interface Description

Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press

the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.

PWR Connector for a power adapter. ON/OFF

Power Switch.

Vigor2130 Series User’s Guide

11..22..33 FFoorr VViiggoorr22113300VVnn

LED Status Explanation

ACT

(Activity)

WAN

LAN 1/2/3/4

Phone1/ Phone2

WPS Button

Interface Description

WLAN

WAN Connector for accessing the Internet. LAN

(1/2/3/4) USB (1/2) Connector for USB storage (Pen Driver/Mobile HD) or

Blinking The router is powered on and running

normally.

off-hook.

Off The phone connected to this port is

on-hook.

Blinking A phone call comes. On Wireless access point is ready. WLAN Blinking It will blink while wireless traffic goes

through.

On Press this button for 2 seconds to wait

for client device making network connection through WPS. When the LED lights up, the WPS connection will

be on. Off The WPS is off. Blinking Waiting for wireless client sending

requests for connection about two

minutes.

Press the button once to enable (WLAN LED on) or disable (WLAN LED off) wireless connection.

Connectors for local networked devices.

printer.

Vigor2130 Series User’s Guide

Interface Description

Phone2/Phone1 Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press

PWR Connector for a power adapter. ON/OFF

Connector of analog phone for VoIP communication

the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.

Power Switch.

Vigor2130 Series User’s Guide

11..33 HHaarrddwwaarree IInnssttaallllaattiioonn

Before starting to configure the router, you have to connect your devices correctly.

1. Connect Line port to land line jack with a RJ-11 cable (Vn model).

2. Connect this device to a modem with an Ethernet cable.

3. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device

allows you to connect 4 PCs directly.

4. Connect Phone port to a conventional analog telephone.

5. Connect detachable antennas to the router for Vigor2130 series (n model).

6. Connect one end of the power cord to the power port of this device. Connect the other

end to the wall outlet of electricity.

7. Power on the router.

8. Check the ACT and WAN, LAN LEDs to assure network connections.

(For the detailed information of LED status, please refer to section 1.1.)

Caution:

1. Each of the Phone ports can be connected to an analog phone only. Do not connect the phone ports to the land line jack. Such connection might damage your router.

2. When the power is shutdown, VoIP phone will be disconnected. However, a phone set connected to Phone 2 port can be used as the traditional telephone for the line will be guided to land line jack via the router (loop through).

Vigor2130 Series User’s Guide

SSttaanndd IInnssttaallllaattiioonn

The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation.

e f

Vigor2130 Series User’s Guide

11..44 PPrriinntteerr IInnssttaallllaattiioonn

You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com.

Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).

1. Connect the printer with the router through USB/parallel port.

2. Open Start->Settings-> Printer and Faxes.

3. Open File->Add a New Computer. A welcome dialog will appear. Please click Next.

Vigor2130 Series User’s Guide

4. Click Local printer attached to this computer and click Next.

5. In this dialog, choose Create a new port Type of port and use the drop down list to

select Standard TCP/IP Port. Click Next.

Vigor2130 Series User’s Guide

6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name

or IP Address and type IP_192.168.1.1 as the port name. Then, click Next.

7. Click Standard and choose Generic Network Card.

8. Then, in the following dialog, click Finish.

Vigor2130 Series User’s Guide

9. Now, your system will ask you to choose right name of the printer that you installed onto

the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next.

10. For the final stage, you need to go back to Control Panel-> Printers and edit the

property of the new printer you have added.

11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next

please refer to the red rectangle for choosing the correct protocol and UPR name.

Vigor2130 Series User’s Guide

The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router.

Note 1: Some printers with the fax/scanning or other additional functions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ; find out the link of

Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.

Note 2: Vigor router supports printing request from computers via LAN ports but not

WAN port.

Vigor2130 Series User’s Guide

Coonnffiigguurriinngg

For using the router properly, it is necessary for you to change the password of web configuration for security and adjust primary basic settings.

22..11 TTwwoo--LLeevveell MMaannaaggeemmeenntt

This chapter explains how to setup a password for an administrator/user and how to adjust basic/advanced settings for accessing Internet successfully.

For user mode operation, do not type any word on the window and click Login for the simple web pages for configuration. Yet, for admin mode operation, please type “admin/admin” on Username/Password and click Login for full configuration.

22..22 AAcccceessssiinngg WWeebb PPaaggee

1. Make sure your PC connects to the router correctly.

Notice: You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to the later section - Trouble Shooting of the guide.

Baassiicc

Seettttiinnggss

2. Open a web browser on your PC and type http://192.168.1.1. The following window

will be open to ask for username and password.

3. For user mode operation, do not type any word on the window and click Login for the

simple web pages for configuration. Yet, for admin mode operation, please type “admin/admin” on Username/Password and click Login for full configuration.

Notice: If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem.

4. The web page can be logged out according to the chosen condition. The default setting is

Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity.

Vigor2130 Series User’s Guide

22..33 CChhaannggiinngg PPaasssswwoorrdd

No matter user mode operation or admin mode operation, please change the password for the original security of the router.

1. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will

open to ask for username and password.

2. Please type “admin/admin” on Username/Password for admin mode. Otherwise, do not

type any word (both username and password are Null for user mode) on the window and click Login on the window.

3. Now, the Main Screen will appear.

Main screen for admin mode operation (full configuration)

Main screen for user mode operation (simple configuration) Note: The home page will change slightly in accordance with the type of the router

you have.

Vigor2130 Series User’s Guide

4. Go to System Maintenance page and choose System Password/User Password.

5. Type New Password in New Password and Confirm New Password fields. Then click

OK to continue.

6. Now, the password has been changed. Next time, use the new password to access the

Web Configurator for this router.

Vigor2130 Series User’s Guide

22..44 QQuuiicckk SSttaarrtt WWiizzaarrdd

Notice: Quick Start Wizard for user mode operation is the same as for admin mode operation.

If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is welcome page, please click Next.

22..44..11 SSeettttiinngg uupp tthhee PPaasssswwoorrdd

The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.

Vigor2130 Series User’s Guide

22..44..22 SSeettttiinngg uupp tthhee TTiimmee ZZoonnee

On the next page as shown below, please select the Time Zone for the router installed and specify the NTP server(s). Then click Next for next step.

22..44..33 SSeettttiinngg uupp tthhee IInntteerrnneett CCoonnnneeccttiioonn

On the next page as shown below, please select the appropriate connection type according to the information from your ISP. There are five types offered in this page. Each connection type will bring out different web page.

Vigor2130 Series User’s Guide

SSttaattiicc IIPP

You will receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers. In most cases, a Cable service provider will offer a fixed public IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address or many IP address to the WAN interface.

IP Address Type the IP address. Subnet Mask Type the subnet mask. Gateway Type the gateway IP address. Primary DNS Server Type in the primary IP address for the router Secondary DNS Server Type in secondary IP address for necessity in the future. Enable The router will detect the MAC address automatically. Or,

check the box to enable MAC address cloning.

Clone MAC Address It is available when the box of Enable is checked. Click Clone

PC Address. The result will be displayed in the field of MAC Address.

After finishing the settings here, please click Next.

Vigor2130 Series User’s Guide

DDHHCCPP

It is not necessary for you to type any IP address manually. Simply choose this type and the system will obtain the IP address automatically from DHCP server.

Enable The router will detect the MAC address automatically. Or,

check the box to enable MAC address cloning.

Clone MAC Address It is available when the box of Enable is checked. Click Clone

PC Address. The result will be displayed in the field of MAC Address.

After finishing the settings here, please click Next.

PPPPPPooEE

PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable modem. All the users over the Ethernet can share a common connection.

PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection for accessing the Internet. Your service provider will provide you information about user name, password, and authentication mode.

Vigor2130 Series User’s Guide

If your ISP provides you the PPPoE connection, please select PPPoE for this router. The following page will be shown:

User Name Assign a specific valid user name provided by the ISP. Password Assign a valid password provided by the ISP. Redial Policy If you want to connect to Internet all the time, you can choose

Always On. Otherwise, choose Connect on Demand.

Idle Time Out Set the timeout for breaking down the Internet after passing

through the time without any action. The unit is seconds. The range is XX ~ XX.

MTU Size

It means Max Transmit Unit for packet. The default setting is 1442.

Enable The router will detect the MAC address automatically. Or,

check the box to enable MAC address cloning.

Clone MAC Address It is available when the box of Enable is checked. Click Clone

PC Address. The result will be displayed in the field of MAC Address.

After finishing the settings here, please click Next.

Vigor2130 Series User’s Guide

+ 211 hidden pages

DrayTek Vigor2130n User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual