Draw-Tite 75144 User Manual

INSTALLATION INSTRUCTIONS

TOYOTA T100 PICKUP

2WD & 4WD

PLYMOUTH, MI

Product No.

33022

75144 87490

SMALL PARTS

PACKAGE 36573

WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY

OCCUR DUE TO OVER TIGHTENING. WARNING: DO NOT DRILL OR WELD TO THIS HITCH.

TWO WHEEL DRIVE ATTACHMENT HOLES

FOUR WHEEL DRIVE ATTACHMENT HOLES

(K) BUMPER BAR

USE ONLY Towing Products SUPPLIED OR APPROVED BOLTS, LOCKNUTS, AND WASHERS TO INSTALL THIS HITCH

(A) LEFT FRAME BRACKET

IMPORTANT NOTES

TOOLS REQUIRED 9/16" SOCKET

18mm WRENCH 7/32" ALLEN WRENCH TORQUE WRENCH

(D) M12 X 1.25 X 35mm BOLT (H) HELICAL LOCK WASHER

(I) NUT

(B) RIGHT FRAME BRACKET

(E) 3/8-16 X 1-1/4 LG. BOLT (F) 3/8 HELICAL LOCK WASHER

(L) 3/8 SERRATED WASHER

(D) M12 X 1.25 X 35mm BOLT (H) HELICAL LOCK WASHER

NOTE: FASTENERS TYPICAL

BOTH SIDES

1. All trucks, remove the two inner bolts along the bottom of the bumper using an allen wrench.

2. 4x4 trucks, Remove the four (2 each side) 12mm bolts that secure the frame reinforcement to the frame. This is inside the frame - above the leaf spring.

3. Install the frame brackets (A) and (B) with the flanges pointing outward. Position the brackets over the holes where the hardware was removed. Install bolt (D), lock washer (H), serrated washers (J), and nut (I). On 4x4 trucks, use the existing nuts in the reinforcement brackets. On 2wd trucks, use the existing nut in the frame. When you have finished installing this hitch on a 4x4 truck, there will be extra nuts and washers remaining in the parts bag.

(J) SERRATED WASHER (J) SERRATED WASHER

(I) NUT

(OVER)

4. Position the center section (C) between the frame brackets (A) and (B). Adjust the center section (C) so that the rear end of the hitch is just below the bumper. Install bolts (D) through the center section (C) and the frame brackets (A) and (B). Install lock washers (H) and nuts (I) on the bolts.

5. Adjust the hitch so that the holes in bar (K), at the end of the hitch, are under the bolt holes in the bottom of the bumper. Install bolts (E) with lock washers (F) and serrated washers (L) into the bottom of the bumper.

6. First, torque the 3/8" bolts (E) to 35 ft•lb. Next, torque the four 12mm nuts (I) to the center section (C). Torque

these nuts to 75 ft•lb. Finally, torque the six 12mm bolts (D) in the frame brackets (A) and (B). Torque these bolts

to 75 ft•lb.

This product complies with safety specification and requirements for the State of New York and VESC regulation V-5 for connecting devices and towing systems. Weight distributing hitch rating is 7000 lb max gross trailer weight and 700 lb max tongue weight. Weight carrying hitch rating is 5000 lb max gross trailer weight and 500 lb max tongue weight. Consult vehicle owner’s manual for towing recommendations and limitations.

LIMITED WARRANTY

Towing Products warrants its Hitches, custom Hitch Receivers, and Sway Controls from date of purchase against defects in material and workmanship under normal use and service, ordinary wear excepted, for the ownership life of the original consumer purchaser. Towing Products will replace FREE OF CHARGE any part which proves defective in material or workmanship when presented to any Towing Products dealer, Towing Products Warehouse, or returned to factory, TRANSPORTATION CHARGES PREPAID, at the address below. THIS WARRANTY IS

LIMITED TO DEFECTIVE PARTS REPLACEMENT ONLY. LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION OR

REPLACEMENT AS WELL AS INCIDENTAL AND CONSEQUENTIAL DAMAGES CONNECTED THEREWITH ARE EXCLUDED. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any damage to the Hitch, Custom Hitch receiver or Sway Control as a result of misuse, abuse, neglect, accident, improper installation, or any use violative of instructions furnished by Towing Products Products, WILL VOID THE WARRANTY. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. In the event of a problem with warranty service or performance, you may be able to go to a small claims court, a state court, or a federal district court.

Towing Products PO Box 8102 47774 Anchor Ct. Plymouth, MI 48170

Towing Products 2351 Winston Park Drive Oakville, Ontario Canada L6H6R7