Draw-Tite 65056 User Manual [en, es, fr]
Installation Instructions
Equi
Utility Knif
2
3
p
pg p
Chevrolet Silverado 2500 HD, 3500 HD
GMC Sierra 2500 HD, 3500 HD
Does not fit Denali HD due to extensive fascia cutting
Note: Fascia trim required. Obtain vehicle owners approval before cutting
CARGO CAPACITY–Do not exceed
Fascia
500 LB. (227 Kg) or Truck Front
Gross Axle Weight Rating, (GAWR).
Part Numbers:
65056
NOTE: If front mounted license
plate is present, repositioning
may be necessary.
Hitch Shown In Proper Position
pment Required:
Tape Measure & Marking Pencil.
Fastener Kit: 65056F
Wrenches: 3/4” & (2) 18mm
Drill Bits: None
e,
4
Tow hooks and
fascia not shown.
Qty. (2) Hex bolt 1/2-13 X 1.500 GR5
1
Qty. (2) Flat washer
2
Access Hole
1
9,000 lb.
(4086 Kg)
MAXIMUM WINCH LINE PULL
MAXIMUM WINCH LINE PULL
Crossmember shown
Cut off for clarity
Bumper support
Existing M12 Flange Bolt Typ
Note: Fasteners typical
Flange nuts for existing
tow hooks
Fascia trim required. Obtain vehicle owners approval before cutting
Qty. (2) Conical Toothed Washer
3
Qty. (2) Hex Nut ½-13
4
both sides
Trim fascia for receiver tube.
1. Trim fascia. See fascia trimming information for proper vehicle model:
Note: CONSULT VEHICLE OWNER BEFORE TRIMMING.
2. Remove the flange nuts on the 2 bolts (1 each side) from existing tow hooks. On driver’s side loosen bolt until flush with the
inboard frame rail. On
3. Raise hitch into position and push both bolts through brackets to support the hitch.
Note: If there is interference with the bumper support, loosen (do NOT
4. Insert ½-13 hex bolt and flat washer thru access hole on inside frame rail and thru hole in frame and slot in hitch side bracket,
both sides.
5. Secure with conical toothed washers and hex nuts..
6. Tighten all fasteners to the required torque specification.
7. If bumper support was loosened in Step 3 re-tighten.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2010 Cequent Performance Products
assenger’s side remove bolt. Keep for re-installation.
remove) and lift the bumper upward for extra clearance.
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Sheet 1 of 6 65056N 9-2-10 Rev. A
-
-
License plate holder relocation
7.C
1/4” hole f
and/or modification required to
install hitch, see 49802 or 5443
sold separately.
Installation Instructions
Chevrolet Silverado 2500 HD, 3500 HD
GMC Sierra 2500 HD, 3500 HD
Does not fit Denali HD due to extensive fascia cutting
Note: Fascia trim required. Obtain vehicle owners approval before cutting
1-5/8"(1.625) [41.275 mm]
Part Numbers:
65056
Existing tow hook bolt.
(Both sides)
Fascia
Cutout
Bumper support
Tow hook
3-1/4“ (3.25) [82.55 mm]
3-1/4“ (3.25) [82.55 mm]
Fascia trim required. Obtain
vehicle owners approval before
cutting
Measure from tow hook bolt.
NOTE: If front mounted license plate is present, license plate holder relocation and/or modification required to install hitch,
see 49802 or 5443 sold separately.
Note: Obtain vehicle owners approval before cutting. Trim fascia for receiver tube.
1. Measure from the tow hook bolt center to the ground.
2. Subtract 4-1/8”(4.125)[105 mm] from step 1. This is the distance from the ground to bottom of fascia cutout.
3. Mark the location of the bottom of fascia cutout on front of fascia.
4. Measure 3-1/4” up from the bottom of fascia cut. This is the location of the top of fascia cutout.
5. Locate the center of the fascia from left to right and mark 1-5/8” each side. ( 3-1/4” square)
6. Drill (4) 3/8” hole in corners.
arefully cut the 3-
rom the fascia.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2010 Cequent Performance Products
Sheet 2 of 6 65056N 9-2-10 Rev. A
-
-
Loading...