Page 1
Installation/Operating Instructions
Targa and Premier 220V Electric Projection Screen—Large Sizes by Draper
These Installation/Operating Instructions are available in the offi cial language of the
country where you purchase the product. Please contact your distributor to request a
copy.
Vous pourriez demander les instructions d’installation et d’opération traduises dans
la langue offi cielle du pays ou vous achetez le produit. Veuillez demander à votre
distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der offi ziellen
Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die
jeweilige Verkaufs-Abteilung.
Before fully operating screen: On Large Targa, remove tape; on Large Premier, lower
viewing surface enough to fully expose shipping brackets, then remove shipping brackets
by loosening screws, removing end shipping brackets, sliding center shipping brackets off
dowel, and re-tightening screws (see diagram).
Caution
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation con trary to instructions in val i dates war-
ranty.
➂ Screen should be accessible for complete removal should fabric be come dam-
aged or should other ser vice be required.
➃ Screen should be installed level (using a carpenter’s level). The case must also
be installed so that the top of the case is level (front-to-back) to prevent the fabric
from contacting the case housing.
➄ Nothing should be fastened to screen dowel or viewing surface.
➅ Operating switch(es) packed separately in screen carton. Do not dis card with
packing material.
➆ Screen operates on 220V AC, 50 Hz., 1 ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply any re spon si bil i ty on the
part of Draper, Inc. for improper in stal la tion or faulty work man ship at the jobsite.
Hanging Screen
General:
Screen should be lifted into position only by the end mounting brackets.
Never attempt to lift screen along its length.
Installer must also insure that wall or ceiling structure is of adequate strength.
Supporting hardware must be essentially vertical. Do not suspend this product using
chain or cable (see note at bottom right regarding this screen with Tork Star).
The screen must be securely fastened using at least two of the mounting holes
provided in each of the case mounting brackets.
When locating view ing surface and checking clear ance for screen’s op er a tion,
remember surface is centered in case. Handle case care ful ly to protect its fi nish.
Regardless of mounting method, screen should be positively and securely sup port ed
so that vibration or even abusive pulling on the viewing surface will not cause case to
work loose or fall. Installer must insure that fas ten ers used are of adequate strength and
suit able for the mounting sur face cho sen.
Ceiling Installation:
Product is very heavy: Installer must provide adequate attachment hardware and
anchors as required. Installer must also insure that ceiling structure is of adequate
strength.
Wall Installation:
Product is very heavy: Installer must provide adequate attachment hardware
and anchors as required. Installer must also insure that wall structure is of
adequate strength.
Caution: Do not remove the roller assembly from the case unless necessary for
repairs. If the roller assembly is removed,
be sure motor is fully re-seated in the
bracket, and re-secure it carefully with
the motor retaining spring and screw (see
diagram below).
Screw is included with Large
Targas and Large Premiers.
Please note: Do not use a power screwdriver to tighten screw. Maximum torque for
tightening screw is 5 lb-inches.
Electrical Connections
Screen operates on 220V AC, 50 Hz., 1 ph. current.
Junction box is located inside left endcap and cover plate is secured to endcap with two
screws. Junction box contains terminal strip, per wiring diagram on reverse.
Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire
connecting screen to switch(es) and switch(es) to power supply should be furnished by
installer. Connections should be made in accordance with wiring diagram supplied, and
wiring should comply with na tion al and local electrical codes.
All operating switches should be “Off” before power is con nect ed.
®
220V AC Single Station Control—3-position up-off-down switch per mits op er a tion to be
stopped at any point. Factory adjusted limit switches au to mat i cal ly stop screen when fully
down or fully up.
220V AC Multiple Station Control—Switches are sim i lar in ap pear ance to 220V Single
Station Control. Screen stops when switch is re leased and may be re start ed in either
direction. Factory adjusted limit switch es stop screen automatically when fully up or fully
down.
24V Control—Three-button up-stop-down switch(es) stop at any point de sired, operate
in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen when fully up
or fully down. Installer should incorporate an all-pole disconnect in the fi xed wiring.
Key Operated Switching—Two kinds of key-op er at ed switches are op tion al ly available
with this unit. ➀ The key-operated power sup ply switch controls power to the screen and
switch es. When it is “off ”, the switches will not operate screen. Key may be removed from
the switch in either “on” or “off” position. ➁ A three-po si tion key switch per mits the screen
to be operated directly by key. In this case, the screen’s operator must always have a key.
RS232/Ethernet—Serial communication and network communication optionally available
with wall switches, RF or IR remote.
Screen has been factory set and should not nor mal ly require further ad just ment. However, if you desire to change the “up” and “down” stop ping po si tions, proceed as follows:
CAUTION: Be sure all switches are in “off ” position before ad just ing limit switches.
Always be pre pared to shut screen off man u al ly when new adjust- ment is being tested.
Screen may be se vere ly dam aged if viewing surface is al lowed to run too far up or too far
down.
Adjusting “fully up” position — “Up” stopping position may be ad just ed by turning the
yellow limit switch adjustment socket. The yellow socket is lo cat ed on left end of screen
roller and is accessible to a screwdriver/Allen wrench (4mm or 5/32"). Turn ing the socket
coun ter clock wise will allow the view ing surface to retract farther into the case. Turn ing it
clockwise will cause the sur face to stop farther out of the case. One full revolution of the
socket will alter the stop ping position of the view ing surface by ap prox i mate ly 1½".
Adjusting “fully down” position — “Down” stopping position may be adjusted by turning the white limit switch adjustment socket. The white socket is located on the left end
of screen roller and is accessible to a screw driv er/Allen wrench (4mm or 5/32"). Turning
the socket coun ter clock wise will allow the viewing surface to run farther down. Turning it
clockwise will shorten the viewing surface, causing it to stop in a less extended po si tion.
At no time should viewing surface be unrolled enough to expose any part of screen roller.
16.8
cm
Use of Large Case Targa or Large Case Premier screens with TorkStar Utility Lineset requires specially modifi ed Large Premier or Large Targa case and mounting brackets. DO NOT use TorkStar with standard Large Case Targa or Premier
screen and brackets. Contact Draper for details.
16.8
cm
Targa Premier
Operation
Adjustments
16.8
cm
16.8
cm
IMPORTANT
Copyright © 2009 Draper Inc. Form 220VTarga-LargeSizes_Inst09-R2 Printed in U.S.A.
If you encounter any diffi culties installing or ser vic ing your large size Targa or Premier screen,
call your dealer or Draper Inc., Spiceland, Indiana, USA, (765) 987-7999 or fax (765) 987-1689.
Page 2
220V Targa and Premier —Large Sizes by Draper
9
Case Dimensions
Types of Installation
Wall Mounted
Appropriate hardware
provided by installer.
Product is very heavy: Installer must provide adequate
attachment hardware and anchors as required. Installer
must also insure that wall or ceiling structure is of
adequate strength.
Ceiling Mounted
Appropriate
hardware
provided
by installer.
Tab-Tension Adjustment
Procedure for Premier
➀ Determine which side requires adjustment.
➁ Secure dowel with one hand.
Caution: Do not touch or bend surface.
➂ Using Philips-head screwdriver,
depress spring-loaded
adjustment screw (see drawing)
and slowly turn clockwise
to tighten tension, or
Dowel
counterclockwise to loosen
tension. The screw adjusts
in ¼ turn increments.
Adjust only one increment (¼ turn).
➃ If problem is not corrected, leave screen in position
for 24 hours to allow surface material to stretch into position.
➄ If problem still is not corrected, repeat steps 2 and 3.
Tensioning
Cable
Adjustment
Screw
16.8
cm
8.6
cm
Dim Targa Premier
A 22.54 cm Varies
B 7.62 cm Varies
Single Station Control
Case Dimensions (Premier Tab Tension Surface Shown)
16.8
cm
1
R73
cm
63 mm
cm
1.7
cm
8.6
cm
B
Wiring Diagrams
CE Approved
Terminal strip in
junction box at left
end of screen
Surface Width + A
Multiple Station Control
Page 2 of 2
Not CE Approved
Terminal strip in
junction box at left
end of screen
Red
10
cm
Cap off with wire
nut & tape
Blue
Two-Way Serial Communication
(RS232) with MC1
Terminal strip in
junction box at left
end of screen
Red-to Screen (directional)
Black-to Screen (directional)
Blue-Common
Brown-Hot to 230V AC
Program LED
Neutral
Hot
Low Voltage Wiring by others
Green/Yellow-Ground
Fuse
All-Pole Disconnect
by Others
STOP
AC Wiring by electrician
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
230V, 50 Hz.
STOP
Control
Switches
24v DC
Eye Port for IR Eye. For RF Receiver
or LED Wall Switch, a Splitter and a
Power Supply is required. Plug RF
Receiver or LED Wall Switch and
Power Supply into splitter, then run
Manual Switch Up
cable from Splitter to MC1 Eye Port.
MC1
Control
switch
Dashed wiring
by electrician
Low Voltage & Wireless Control
Neutral
L1
PE
230V,
50 Hz.
Red-to screen (directional)
Brown-to screen (directional)
White-Common to screen, 230V AC
Black-to 230V AC
Yellow-to 230V AC
Green-Ground
Dashed wiring by electrician
Eye Port for IR Eye, RF Receiver or LED
Switch For more than one of these,
a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Low voltage wiring by others
Aux Por t for connecting additional
LVC-III modules (up to six totalconnect from Aux to Eye).
Red
Red
Neutral
Hot
230V, 50 Hz.
STOP
STOP
230V, 50 Hz.
Control
Switches
24v DC
Black
Black
Black
Dashed wiring
by electrician
Hot
Neutral
All-Pole Disconnect
by Others
Blue
Blue
Terminal strip in
junction box at left
end of screen
See separate Serial CommunicationRS232 Instruction sheet for enabling
RS232 with the MC1.
www.draperinc.com
(765) 987-799
Loading...