Draper PPW650 User Manual

INSTRUCTIONS FOR

6.5HP Petrol

Pressure Washer

Stock No.83818 Part No.PPW650

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND

EFFECTIVE USE OF THIS PRODUCT.

GENERAL INFORMATION

These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before assembling, operating or maintaining this product.

This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.

AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.

Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy of continuous improvement determines the right to make modifications without prior warning.

1.TITLE PAGE

1.1 INTRODUCTION:

USER MANUAL FOR:

6.5HP PETROL PRESSURE WASHER

Stock no. 83818. Part no. PPW650.

1.2 REVISIONS:

Date first published November 2015

As our user manuals are continually updated, users should make sure that they use the very latest version.

Downloads are available from: http://www.drapertools.com/b2c/manuals

DRAPER TOOLS LIMITED	WEBSITE:	www.drapertools.co
HURSLEY ROAD	PRODUCT HELPLINE:	[phone]
CHANDLER’S FORD	GENERAL FAX:	[phone]
EASTLEIGH
HAMPSHIRE
SO53 1YF
UK

1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:

WARNING! Information that draws attention to the risk of injury or death.

CAUTION! Information that draws attention to the risk of damage to the product or surroundings.

1.4 COPYRIGHT © NOTICE:

Copyright © Draper Tools Limited.

Permission is granted to reproduce this publication for personal & educational use only. Commercial copying, redistribution, hiring or lending is prohibited.

No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited.

In all cases this copyright notice must remain intact.

2.CONTENTS

2.1 CONTENTS
PAGE CONTENT			PAGE
1	TITLE PAGE
	1.1	INTRODUCTION ....................................................................................................	2
	1.2	REVISION HISTORY................................................................................................	2
	1.3	UNDERSTANDING THIS MANUAL .......................................................................	2
	1.4	COPYRIGHT NOTICE..............................................................................................	2
2	CONTENTS
	2.1	CONTENTS .............................................................................................................	3
3	GUARANTEE
	3.1	GUARANTEE ..........................................................................................................	4
4	INTRODUCTION
	4.1	SCOPE ...................................................................................................................	5
	4.2	SPECIFICATION ......................................................................................................	5
	4.3	HANDLING & STORAGE ........................................................................................	5
5	HEALTH & SAFETY INFORMATION
	5.1	GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE .................................	6-7
	5.2	SPECIFIC SAFETY INSTRUCTIONS FOR PRESSURE WASHER USE ........................	8-9
6	TECHNICAL DESCRIPTION
	6.1	IDENTIFICATION ....................................................................................................	10
7	UNPACKING & CHECKING
	7.1	PACKAGING...........................................................................................................	11
	7.2	WHAT’S IN THE BOX? ...........................................................................................	11
8	ASSEMBLING THE PRESSURE WASHER
	8.1	HOSE AND CABLE TIDY ........................................................................................	12
	8.2	PRESSURE HOSE TO PRESSURE PUMP ..................................................................	12
	8.3	PRESSURE HOSE TO GUN......................................................................................	12
	8.4	LANCE TO GUN .....................................................................................................	13
	8.5	SELECTING THE RIGHT NOZZLE ............................................................................	13
	8.6	NOZZLES TO LANCE ..............................................................................................	14
	8.7	PRESSURE PUMP TO WATER SUPPLY...................................................................	14
9	PREPARING THE PRESSURE WASHER
	9.1	ADDING ENGINE OIL.............................................................................................	15
	9.2	LOW OIL SENSOR ..................................................................................................	15
	9.3	ADDING PETROL ...................................................................................................	16
	9.4	USING PRESSURE WASHER AT HIGH ALTITUDES ................................................	16
10	OPERATING THE PRESSURE WASHER
	10.1	STARTING ..............................................................................................................	17
	10.2	USING THE GUN ....................................................................................................	18
	10.3	WASHING AND CLEANING ...................................................................................	18
	10.4	EXHAUST CONTROL SYSTEM ...............................................................................	19
	10.5	PRESSURE ADJUSTMENT.......................................................................................	19
	10.6	USING CHEMICALS AND CLEANING SOLVENTS...................................................	20
	10.7	SHUTTING DOWN .................................................................................................	21
11	MAINTENANCE
	11.1	MAINTENANCE SCHEDULE ...................................................................................	22
	11.2	CLEANING NOZZLE................................................................................................	23
	11.3	CLEANING WATER INLET SCREEN FILTER ............................................................	23
	11.4	CLEANING PRESSURE WASHER ............................................................................	24
	11.5	STORAGE ...............................................................................................................	24
	11.6	PREPARING FOR USE AFTER STORAGE ................................................................	26
12	TROUBLESHOOTING
	12.1	TROUBLESHOOTING GUIDE..................................................................................	27
13	DISPOSAL
	13.1	DISPOSAL...............................................................................................................	31
DECLARATION OF CONFORMITY ..........................................................................................			ENCLOSED

3

3.GUARANTEE

3.1 GUARANTEE

Draper tools have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship.

Should the tool develop a fault, please return the complete tool to your nearest distributor or contact Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, SO53 1YF. England. Telephone Sales Desk: [phone] or Product Helpline [phone].

A proof of purchase must be provided with the tool.

If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months from the date of purchase except where tools are hired out when the guarantee period is 90 days from the date of purchase. The guarantee is extended to 24 months for parts only. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other than the authorised Draper warranty repair agent.

Note: If the tool is found not to be within the terms of warranty, repairs and carriage charg will be quoted and made accordingly.

This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised.

Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period.

Please note that this guarantee is an additional benefit and does not affect your statutory rights.

Draper Tools Limited.

4

4.INTRODUCTION

4.1 SCOPE

This manual is intended to give an overview of this machines features, functionality and safe operation.

4.2 SPECIFICATION

Stock no. .................................................................................................................................	83818
Part no. ................................................................................................................................	PPW650
Engine ......................................................................................................................	6.5HP 4-stroke
Engine displacement ..............................................................................................................	196cc
Speed (no load) ....................................................................................................	3350-3550 r/min
Working pump pressure ......................................................................................	168bar (2430psi)
Max. pump pressure .............................................................................................	186bar (2700psi)
Delivery ....................................................................................................................	474l/h (7.9l/m)
Weight (nett)............................................................................................................................	30kg
4.3 HANDLING & STORAGE

This machine should be stored in a dry location and in its box. Avoid storing this machine in areas prone to damp or humidity.

Remove residual fuel from the fuel tank if storing for several months. Run clean water through chemical inlet.

Do not allow water to freeze in pump, gun, lance or hose.

5

5.HEALTH & SAFETY INFORMATION

5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE

When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe.

Common sense and a respect for the tool will help reduce the risk of injury.

Read the instruction manual fully. Do not attempt any operation until you have read and understood this manual.

Most important you must know how to safely start and stop this machine, especially in an emergency.

Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilt on the floor could result in you slipping.

Find a suitable location. If the machine is bench mounted; the location should provide goo natural light or artificial lighting as a replacement. Avoid damp and dust locations as it will have a negative effect on the machine’s performance.

If the machine is portable; do not expose the tool to rain. In all cases do not operate power tools near any flammable materials.

Beware of electric shock. Avoid contact with earthed surfaces; because they can conduct electricity if there is an electrical fault with the power tool. Always protect the power cable and route it away from danger.

Keep bystanders away. Children, onlookers and passers by must be restricted from entering the work area for their own protection. The barrier must extend a suitable distance from th tool user.

Unplug and house all power tools that are not in use. A power tool should never be left unattended while connected to the power supply. They must be housed in a suitable location, away locked up and from children.

Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what they are capable of doing. Do not attempt to use a power tool (or adapt it in any way for an application it is not designed for. Select a tool appropriate for the size of the job.

Overloading a tool will result in tool failure and user injury: This covers the use of accessories.

Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become entangled in moving machinery: This can also result in parts of body being pulled into the machine.

Clothing should be close fitted, with any long hair tired back and jewellery and neck ties removed. Footwear must be fully enclosed and have a nonslip sole.

6

5.HEALTH & SAFETY INFORMATION

Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous if not suitably protected against. If the work involving the power tool creates dust or fumes; wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods must be protected against. Wear vibration reducing gloves and allow long breaks between uses. Protect against dust and swarf by wearing approved safety goggles or a face shield. These are some of the more common hazards and preventions; however, always find out what hazards are associated with the machine/work process and wear the most suitable protective equipment available.

Do not breathe contaminated air. If the work creates dust or fumes; connect the machine (if possible) to an extraction system either locally or remotely. Working outdoors can also help if possible.

Move the machine as instructed. If the machine is hand held, do not carry it by the power supply cable. If the product is heavy; employ a second or third person to help move it safely or use a mechanical device. Always refer to the instructions for the correct method.

Do not overreach. Extending your body too far can result in a loss of balance and you falling. This could be from a height or onto a machine and will result in injury.

Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged or missing parts immediately with original parts from the manufacturer. As applicable; keep blades sharp; moving parts clean, oiled or greased; handles clean; and emergency devices working.

Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts may continue to move due to momentum. Wait for all parts to stop; then unplug it from the power supply before making any adjustments, carrying out maintenance operations or just finishing using the tool.

Remove and check setting tools. Some machinery requires the use of additional tools or keys to set, load or adjust the power tool. Before starting the power tool always check to make certain they have been removed and are safely away from the machine.

Prevent unintentional starting. Before plugging any machine in to the power supply, make sure the switch is in the OFF position. If the machine is portable; do not hold the machine near the switch and take care when putting the machine down; that nothing can operate the switch.

Carefully select an extension lead. Some machines are not suitable for use with extension leads. If the tool is designed for use outdoors; use an extension lead also suitable for that environment. When using an extended lead, select one capable of handling the current (amps) drawn by the machine in use. Fully extend the lead regardless of the distance between the power supply and the tool. Excess current (amps) and a coiled extension lead will both cause the cable to heat up and can result in fire.

Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power tool if you are under the influence of drugs (prescription or otherwise), including alcohol or if you are feeling tired. Being disorientated will result in an accident.

Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant international and local standards and as such should be maintained and repaired by someone qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains safe to use.

7

5.HEALTH & SAFETY INFORMATION

5.2SPECIFIC SAFETY INSTRUCTIONS FOR PRESSURE WASHER USE

Warning: This appliance is for outdoor use only.

Warning: Always disconnect the electricity and water supplies on completion of eve job.

Warning: Never use the appliance if the electrical cable or important parts of the appliance are damaged, e.g. safety devices, high pressure hose, gun, etc.

Warning: This appliance has been designed for use with a neutral shampoo based o biodegradeable anionic surface active detergents. The use of other detergents or chemicals may put the appliance’s safety at risk.

Warning: Never use the appliance with people in the vicinity, unless they are wearin protective clothing.

Warning: Do not direct the nozzle toward mechanical parts containing lubricant grease, as the grease will dissolve and spread over the surrounding groun Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 30cm, otherwise the vehicle tyre/tyre valve could be damaged by the high-pressure jet. The first indication of this is a discolouration of the tyre. Damaged vehicle tyres/tyre valves can be deadly dangerous.

Warning: High pressure jets may be dangerous if improperly used. Jets must never b pointed at people, animals, live electrical equipment or the appliance itsel

Warning: The hoses, accessories and high pressure couplings are important for the appliance’s safety. Use only hoses, accessories and couplings recommende (it is extremely important to protect these components against damage by avoiding their improper use and protecting them against bending, knocks and scratches).

The gun is fitted with a safety catch. Whenever use of the machine is interrupted it is important to operate the safety catch to prevent accident activation of the jet.

Warning: – Never point the jet at yourself or others to clean clothing or footwear.

–Never allow children or untrained people to use the appliance.

–Safety features: gun equipped with safety locking device, appliance

–equipped with (Class 1) overload cutout, pump equipped with by-pass

–valve or shutdown device.

–The safety button on the gun is not there to lock the lever during operation, but to prevent its accidental operation.

Warning: Appliances equipped with Total Stop System: these appliances should not be left in standby for more than 5 minutes.

Warning: Switch the appliance off completely (master switch ON/OFF) whenever it is left unattended.

8

5.HEALTH & SAFETY INFORMATION

Warning: Every machine is tested in its operating

conditions, so it is normal for a few drops of water to be left inside it.

Warning: Take care not to damage the electric cable. Have a damaged power cord replaced immediately by an authorized service point or an electrical specialist.

Warning: The high pressure hose is designed and produced to withstand high pressures. To avoid damage, it must be handled with special care. Misuse may lead to premature breakages or damage and cause the loss of warranty cover.

Warning: Never start the high-pressure cleaner without first completely unwinding the high-pressure hose.

Warning: When winding and unwinding the hose take care not to cause the high pressure cleaner to overturn.

Warning: Before unwinding or winding the hose, switch the machine off and release the pressure in the hose itself (switching off).

9

6.TECHNICAL DESCRIPTION

6.1 IDENTIFICATION

	Petrol engine.		Lance.
	Wheel.		Nozzle panel.
	Frame.		Pressure pump.
	Detergent tank.		High pressure hose.
	Gun.		Selection of nozzles.

10