Draper 242018 Instructions

Ultimate Folding Screen Dress Kit by Draper

®

① Attach Valance Bar to frame (see Fig. 1).

Assembly Instructions

Figure 1

② Valance and Drapes snap onto Mounting Bars as shown below. Please
Note: The valance may show some fullness (see Fig. 2).

Drape
(back

Valance

side)

(front)

Snaps to
Valance Bar

Figure 2

③ Drape Bars mount to Valance Bar and lock using a ball detent
(see Fig. 3).

Snaps to
Drape Bar

Figure 4

Adjustable Skirt Bar

for multiple formats

For the ability to change from one viewing format to another (for in­stance, form NTSC 4:3 to HDTV 16:9), use Draper's Adjustable Skirt Bar:

Attach one end of skirt bar to either leg by placing the outer plate on
the outside of the leg/frame, and placing the handy crank and washer on the
inside. Run the handy crank through the gap between the leg and frame (gap
between leg and frame), then attach the other end to the other leg. The skirt
then attaches to snaps located along the skirt bar.

Figure 3

Please Note: If you have an older Valance Bar, the hole for the Drape Bar
ball-detent will be located too close to the edge of the Valance Bar. You
will need to drill a new hole. See instructions on page 2.

Caution: Beware of pinch points.

④ For adjustable skirt bar, see box at right. For standard skirt attachment:
The skirt attaches to snaps located along the bottom black border of the
viewing surface. (see Fig. 4)

If you encounter any diffi culty installing or ser vic ing your Ultimate Folding Screen Dress Kit by

Copyright © 2012 Draper Inc. Form UFS-DressKit_Inst12 Printed in U.S.A.

Draper, call your dealer or Draper, Inc., Spiceland, Indiana, [phone] or fax [phone].

If adjustable skirt bar is provided with a Middle Support, place in center
of bottom frame and use adjustment knob to set to the proper height (see
pictures below).

Please Note: Middle Support height should be set so the bottom of the
screen frame is supported, but is not pushed upward so that it bows
up in the center.

Ultimate Folding Screen Dress Kit by Draper

9

Updating and/or enabling "Old" Valance

Bar to use the new design cast Drape Bars

① Determine if Valance Bar has the "Old" or New hole (refer to template below).
② Print template to scale (100% size) and measure tube width (1¼" [31.75mm]) with ruler or tape measure to

verify scale.

③ Place template over end of Valance Tube and align end of tube and/or "old" hole centerpoint with template.
④ Mark centerpoint of new hole on tube.
⑤ Drill new hole through one wall of tube with .156" (5/32") [4mm] drill bit.
⑥ Rotate template 180 degrees and repeat steps for opposite side Drape Bar hole.

Page 2 of 2

“Old” Drape Bar Hole Location

1¼"

"

(31.75mm)

8

/

5

(15.87mm)

Outer Edge of Valance Bar

① Determine if Valance Bar has the "Old" or New hole (refer to template above).
② Print template to scale (100% size) and measure tube width (1¼" [31.75mm]) with ruler or tape measure to

verify scale.

③ Place template over end of Valance Tube and align end of tube and/or "old" hole centerpoint with template.
④ Mark centerpoint of "old" hole on tube.
⑤ Drill new hole through one wall of tube with .156" (5/32") [4mm] drill bit.
⑥ Rotate template 180 degrees and repeat steps for opposite side Drape Bar hole.

17

Ø .266 (

/64") (7mm)

½"

(13.26mm)

New Wingbar Hole Location

Ø .156 (5/32") (4mm)

3

3

/8"

(85.28mm)

6"

(152.4mm)

Using "New" Valance Bar with the old design Drape Bars

C

L

Tubes have a centerline groove to
locate centerpoint for drilling.

www.draperinc.com

(765) 987-799