Nocturne+ C
MOUNTING
Dowel
Wall Mounting Bracket
Crank Operated Exterior Projection Screen
INSTRUCTIONS
Installation & Operation
Crank
Operator
Crank
Handle
Wall Mounting Bracket
Wall
Mounting
Bracket
Viewing
Surface
Cable
Guide
CAUTION
1. Inspect all boxes to make sure you have received the proper screen and parts.
Controls may be shipped separately, or in same carton as screen.
2. Open cartons lengthwise.
3. All hardware must be installed level. Screen must be level and square.
4. It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting surface.
5. Please read the following installation guidelines thoroughly and follow them carefully.
Failure to do so invalidates warranty.
Please Note: Custom products/installations may not be reflected by this document.
Call Draper, Inc. if you have questions about your installation.
TOOLS
REQUIRED
Pencil
Tape Measure
Dowel
Cable Mount
(Deck Mount Shown)
Section 1 - Preparation of Installation
1. Make sure mounting surface is strong enough to hold the Nocturne+.
Please Note:
2. Verify unit measurements, and make sure it will fit in the desired location.
Please Note: The Dowel does not retract into the Case.
This will need to be accounted for if mounting over a swinging window or door.
3. Mounting brackets MUST be installed with a gap of 1¾” (45mm) between the End Cap
and the Mounting Bracket edge (See Fig. 1). Mark wall, jamb or ceiling.
It is the responsibility of installer to use appropriate fasteners for the mounting surface.
1¾”
(45mm)
BRACKET
END
CAP
Level
Power Drill
Hardware
(by Others)
4. Drill small starter holes (if necessary) in mounting surface.
Figure (1)
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2017 All Rights Reserved | FORM: Nocturne_C_Inst17
Nocturne+ C
Leave a
1¾” (45mm)
GAP
Attach
Mounting Bracket
as spacer and
Tighten Set Screws
page 2 of 4
Section 2 - Mounting Case with Brackets - Wall Installation
Attaching Mounting Brackets
1. Attach mounting brackets to the wall using #10 flat head screws installed flush with bracket.
Be sure to use AT LEAST 2 of the top mounting holes (See Fig. 2).
Attaching Case to Mounting Brackets
1. Attach Case to brackets and tighten Set Screws (See Fig. 3).
2. You are now ready to mount the Side Cables (See Page 3).
Figure (2)
Section 3 - Mounting Case - Permanently to Ceiling or Wall
Attaching Mounting Brackets to Case
1. Attach Mounting Brackets to the Case as a spacer between the Case and the wall.
Please Note: Leave a 1¾” (45mm) gap between End Cap and Mounting Bracket (See Fig. 4),
and tighten set screws.
2. Removing Roller Assembly
A. Remove screws from bottom of Case, remove Front cover and set aside.
B. Remove Quick Release Pin from Idler End of Roller Assembly.
C. Remove Roller Assembly, Idler End first, and set aside.
Figure (3)
Tighten Set Screws
Figure (4)
Figure (5)
REMOVE
REMOVE
COVER
COVER
3. Mounting to Ceiling / Wall
Using the mounting holes in the end caps as a guide (See Fig. 6), drill pilot holes on both ends
of the Case. Attach to mounting surface using appropriate fasteners.
Please Note:
It is the responsibility of installer to use appropriate fasteners for the mounting surface.
4. Once the Case is secured to the mounting surface, re-install Roller Assembly*,
Quick Release Pin and Front cover.
5. You are now ready to mount the Side Cables (See Page 3).
REMOVE QUICK
RELEASE PIN
REMOVE ROLLER ASSEMBLY
Remove screws from
bottom of Case
Figure (6)
CEILING
CEILING
MOUNT HOLES
MOUNT HOLES
WALL
MOUNT HOLES
Nocturne+ C
of
5"
(127mm)
4"
(102mm)
2¼"
(57mm)
1¾"
(45mm)
1"
(25mm)
(92mm)
(92mm
3 5/8"
(92mm)
3 5/8"
(92mm)
page 3 of 4
Section 4 - Installing Cable Guides
Before Installing the Cable Guides, remove the Roller assembly from the Case.
(See Removing Roller Assembly section on Page 2).
1. Thread Cable Guide through dowel and then the provided hole in the endcaps
(see Figure 7).
2. Tighten the Cable Clamp. It should rest on the endcap with no slack or kinks in the
cable guide.
3. Pull the Cable Guide taught and parallel with edge of the fabric panel.
Determine the location of the Wall or Deck Mount.
4. Attach Wall or Deck Mount to surface using appropriate hardware.
5. Insert the Jackscrew end of the Cable Guide into the Wall/Deck Mount.
Tension to 8 in-lbs, so the screen will move up and down easily along the cable.
Please Note: Depending on the height of the screen, you may need to adjust where the
Cable Clamp is located on the Cable Guide.
6. Cut off the excess cable.
7. Repeat on the opposite side of the screen.
Figure (7)
1. Thread Cable Guide
through dowell and
then the provided hole
in the endcap.
2. Tighten Cable Clamp
3. Pull Cable Guide taught.
4. Install Wall or Deck Mount
Guide Cable
Dowel
3
3
/32” Cable
/32” Cable
Clamp
Clamp
Screen
5. Attach Jackscrew
Guide Cable to
Wall or Deck Mount
Section 9 - Component Dimensions
Headbox
3 5/8"
(92mm)
3 5/8"
)
Wall
Mount
OR
Mounting Bracket
4"
(102mm)
(25mm)
35/8"
(45mm)
½"
(19mm)
7
NOTE: Mounting brackets attach to surface with #10 Flat Head Screw
½"
(19mm)
1½"
(38mm)
1½"
(38mm)
Deck
Mount
1"
1¾"
/8" (22mm)
Nocturne+ C
Screen Width
6’ (182cm)
Section 9 continued - Component Dimensions
Section 10 - Assembled Dimensions
page 4 of 4
Crank Handle
35/8"
(92mm)
(41mm)
7
/16"
15/8”
Surface Width
35/8"
(92mm)
Cable
Guide
Length
Wall
Mount
Deck
Mount
Dowel Width
Loading...