dormakaba USA 1SW100 Users Manual
Switch™ Core
Installation Instructions
BEFORE YOU BEGIN:
It is critical to ensure that Switch™ Core is compatible with your Lock Hardware. Please carefully review page 4 and page 5 of this
document [Switch™ Core Compatibility Guide] to ensure that you are installing Switch™ Core into appropriate Lock Hardware.
OVERVIEW
Compatible
Devices:
Lever Handle
A
Throw Member*
B
Core 7-Pin
C
Control Key
D
Switch™ Core
E
Battery
F
Android™ 5+
G
H
I
iOS: 11.0+
Battery Cap
Hex Key 1/16"
Battery
Removal Tool
H
included
*NOTE:
The throw
member (B)
will be reused.
C
D
F
G
Switch™ Core Installation Instructions
1 2
DISENGAGE CONTROL LUG
A
*B
Outside of door
E
I
not included
REMOVE CORE AND
THROW MEMBER
15°
D
D
15°
Insert the control key (D), and rotate 15° clockwise to
disengage the control lug.
D
NOTE: Keep the
throw member (B)
to reuse.
With the control key (D) rotated 15°, remove the core (C) and
the throw member (B). If the throw member (B) or the throw
pins do not come out with the core (C), leave them in the lock.
T91407_A ©2020 All rights reserved.1/20BEST is a trademark of dormakaba USA Inc.
B
C
D
Switch™ Core Installation Instructions
3
CORE ORIENTATION
E
Control lug
retracted
Control lug
extended
The hex key (H) should come inserted in the core (E) with the control lug retracted. If so, go to step 5. Otherwise, go to step 4
to retract the control lug.
4
RETRACT CONTROL LUG
Lobe
Knob
Hole
E
Rotate the knob to align the hole in the circuit
board with the control access hole in the core (E).
NOTE: The core (E) must be in installation mode for the hex key (H) to access
the control lug. If not, the hex key (H) cannot be rotated. If this is the case,
please reference the Switch™ Tech user guide for further instructions.
https://support.bestaccess.com/hc/en-us/articles/360036366673
Control lug
shown extended
H H
Insert the hex key (H). Then gently push and rotate the hex key (H)
counterclockwise to retract the control lug.
H
Control lug
shown retracted
5
INSERT CORE
Control lug
shown retracted
A
B
E
Align the throw member (B) with the lock and insert the core (E).
NOTE: Insert throw
member (B) in core
if needed.
T91407_A ©2020 All rights reserved.2/20BEST is a trademark of dormakaba USA Inc.
Switch™ Core Installation Instructions
6
ENGAGE CONTROL LUG
H
H
E
E
Rotate the hex key (H) clockwise to extend and engage
the control lug. Remove the hex key (H). Gently pull on
the knob to ensure that the core (E) is properly installed.
H
7
INSERT BATTERY
E
NOTE: The core can
now be initialized in the
Switch™ Mobile App.
Insert the battery (F) with the positive polarity
facing out. Carefully align the battery cap (G)
with the knob and gently press until the battery
cap (G) SNAPS securely into place.
Battery Tool Instructions
WARNING: DO NOT force the battery cap (G) onto the knob as the
electrical contacts may bend, rendering the core (E) inoperative.
Electrical contact
1 2 3
G
+
E
E
I
G
I
WARNING: DO NOT
force the battery cap
(G) onto the knob as the
electrical contacts may
bend, rendering the core
(E) inoperative.
F
E
G
+
G
COMPLETE
I
Slide the battery tool (I)
over the battery cap (G).
Remove the battery tool (I)
and the battery cap (G).
4 5 6
NOTE:
Once the new
E
Remove the old battery (F). Insert the new battery (F) with
F
the positive polarity facing out.
E E
Product Care Instructions
CAUTION: Handle the product with care.
Do not spray product with foreign materials.
battery is installed, the
F
core may need to charge.
Carefully align the battery cap (G)
with the knob and gently press
until it SNAPS securely into place.
CAUTION: Use a clean dry or barely dry damp
cloth to clean product.
Separate the battery tool (I)
and the battery cap (G).
G
COMPLETE
T91407_A ©2020 All rights reserved.3/20BEST is a trademark of dormakaba USA Inc.
Loading...