DoorKing 9406, 9410 Instructions Manual

Instructions for 9406 & 9410 Single-Channel Loop Detector

These loop detectors are designed to be used with DoorKing vehicular gate operators only. The
detector plugs into loop detector ports on the gate operator control board eliminating the need for any
hard wiring other than the connection of the loop itself. The detector also employs several automatic
and advanced features that will decrease "false" calls and assist technicians in the field with trouble
shooting loop problems. Refer to the LOOPINFO manual for information on installing in-ground
loops.

Sensitivity Boost

The sensitivity boost feature automatically increases the sensitivity of the loop detector when the
detector is tripped by the passage of a vehicle over the loop. This prevents the detector from "losing"
high bed vehicles as they pass over the loop.

Fast-Trak

When Fast-Trak is turned on, the detector will track slow frequency shifts in the loop twice as fast as
when this feature is turned off. This feature is useful on poor quality loops that drift in frequency. An
indication of this would be when the detector has many "false" calls.

Caution should be exercised when using the Fast-Trak feature. When Fast-Trak is turned ON, it will
cause the presence time of the detector to be about half that of normal. That is to say, the detector
will "tune out" vehicles that are parked on or near the loop about twice as fast as when this feature is
turned off. For this reason, we recommend that the Fast-Trak feature only be used as a

temporary solution to loop frequency drift problems that are typically (but not always) caused
by the use of poor quality wire in the loop itself. If excessive frequency drift continues (indicated

by many "false" calls), the loop itself will have to be replaced.

Frequency Measurement

Whenever the detector is powered up, or when the reset switch is pressed, the detector will blink out
the frequency that the loop has tuned to (in KHz) on the CALL LED. For example, five blinks - pause ­six blinks would indicate the loop has tuned to 56 KHz.

This automatic frequency measurement is useful in applications where two or more loops and loop
detectors are in close proximity to each other. A common problem with loop detectors "false calling" is
because two or more loops in close proximity to each other are cross talking. Knowing what
frequency the loop has tuned to allows you to reset the frequency on one of the detectors as far from
the other detector as possible.

Loop Monitor

The loop detector constantly monitors the frequency of the loop to determine if the frequency is too
high or too low, or if the loop has opened. When this happens, the detector will LOCK ON and the
loop CALL LED will flash. If the frequency of the loop returns to nominal levels, the detector will
resume normal operation but will continue to flash the CALL LED.

A flashing CALL LED is an indication that a problem exist in the loop itself and that the loop should be
replaced. The CALL LED can be reset by pressing the reset button.

P/N 9406-065 REV B 7/04

Plug the loop detector into the desired port (open, reverse) on
the gate operator control board. The output of loop 1 is feed
directly to the operator control board, or can be switched to a
terminal. Refer to the gate operator installation manual.

Connect the lead-in wires from the loop to the terminals
marked LOOP 1. Set the frequency and operation switches as
required.

POWER LED will illuminate whenever power is applied to the
loop detector. L1 is the CALL LED and will illuminate when the
detector senses a vehicle in the loop field and will also indicate
the loop frequency when the detector is powered up.

Pressing the RESET button clears faults and resets the
detector anytime that it is pressed.

LOOP FREQUENCY ADJUSTMENT

Switch 1 Switch 2

High OFF OFF

Med-High OFF ON

Med-Low ON OFF

Low ON ON

1
2
3
4

FREQUENCY

POWER

RESET

LOOP 1

1
2

L1

LOOP DETECTOR OPERATION ADJUSTMENTS

FAST-TRAK SENSITIVITY BOOST

Switch 1 Switch 2 Switch 3 Switch 4

Low OFF OFF

OFF-Normal

Engaged

ON-FastTrak

Med-Low OFF ON

Med-High ON OFF

High ON ON

Engaged

ON-Boost

OFF-Normal

P/N 9406-065 REV B 7/04