Page 1
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
866 Langs Dr.
Cambridge, Ontario
CANADA N3H 2N7
TRIM LINE SCREEN ROOM
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
INSTALLATION
INSTRUCTIONS
TRIM LINE
SCREEN ROOM
9472XX.X07
REVISION A
Form No. 3107887.030 09/16
©2016 Dometic Corporation
LaGrange, IN 46761
9472XX.X09
1
Page 2
SAFETY INSTRUCTIONS
This manual has safety information and instructions to help users eliminate or reduce the risk of
accidents and injuries.
RECOGNIZE SAFETY INFORMATION
!
This is the safety-alert symbol. When you see this
symbol in this manual, be alert to the potential for
personal injury .
TRIM LINE SCREEN ROOM
Follow recommended precautions and safe operating instructions.
UNDERSTAND SIGNAL WORDS
A signal word , WARNING OR CAUTION is used
with the safety-alert symbol. They give the level of
risk for potential injury .
WARNING
!
ous situation which, if not avoided, could result in
death or serious injury .
CAUTION
!
ous situation which, if not avoided may result in
minor or moderate injury .
CAUTION
symbol indicates, a potentially hazardous situation which, if not avoided may result in property
damage.
indicates a potentially hazard-
indicates a potentially hazard-
used without the safety alert
Read and follow all safety information and instructions.
2
Page 3
TRIM LINE SCREEN ROOM
TRIM LINE SCREEN ROOM
INSTALLATION
APPLICATION:
The A&E Trim Line Screen Room is available in sizes to
correspond with the various sizes of Trim Line Awnings.
TOOLS REQUIRED FOR INSTALLATION:
Pencil 1/8 Drill Bit
Measuring Tape Center Punch
Phillips Screwdriver Hammer/Mallet
Drill (for Hook Stakes)
IMPORTANT: Read the entire installation procedure
before starting the installation.
The Dometic Corporation reserves the right to modify appearances and specifications without notice.
INSTALLATION
During installation, care must be taken not to scrape and
damage the panel and skirt.
1. In order to correctly match the Screen Room to the right
size Trim Line Awning, you must know the length of the
awning. See FIG. 1A.
The A&E Trim Line Screen Room consists of (1) continuous panel for the front, sides and rear skirt.
The above-mentioned panel and skirt are secured to the
vehicle, the awning and to the ground by means of hook
and loop fasteners, twist fasteners and hook stakes
(provided). See FIG. 1C.
NOTE: The inner and outer sides of all panels can be
checked by looking at the hook and loop fastener
strips. The fastener strip on the front is on the
outside.
2. Set up awning for installation of Trim Line Screen Room.
To facilitate accurate installation, vehicle should be
parked on reasonably flat ground.
FIG. 1A
SELECTING THE
CORRECT SIZE
Open awning and install front support and side rafter pole
as shown in FIG. 2
FIG. 2
SIDE VIEW
AWNING FABRIC
SIDE RAFTER POLE
FRONT
SUPPORT
SIDE OF
VEHICLE
3. After awning is set up, remove screen room from storage
bag and line up in position with awning as shown in FIG.
3.
FIG. 3
Hook & Loop
Fastener Sewn on Top
of Awning Fabric
and Under Valance
4. Fasten front of screen room to front by joining hook & loop
fasteners together under valance. Pull side panels over
rafters and join to fabric on top of awning on both sides.
5. When attaching screen room to awning at bag, pull bag
away from awning and bunch bag so that screen room is
securely attached to awning fabric inside of bag.
(AWNING SIZE)
FIG. 1B
FRONT & SIDE
PANELS ARE ONE PIECE
LENGTH
VEHICLE
SKIRTING
FASTENER
STAKE
FIG. 1C
3
Page 4
TRIM LINE SCREEN ROOM
WARNING
!
6. Flaps at rear of side panel on screen room are to fasten
to tent canvas at lifter mechanism. Pull tent canvas flap
away from hook & flap strips. Secure screen room flap
to tent canvas using hook & loop fasteners sewn into
both. Secure tent flap to screen room flap as shown in
FIG. 4.
FIG. 4
7. If camper does not have covers for lifter mechanism, fold
screen room flap around lifter as shown in FIG. 5.
FIG. 5
Twist fasteners on each side
FIG. 6
Tie straps attach
around support pole
flap and on rear skirt.
Hook & Loop
Fasteners
Grommets
Skirt
Hook &
Loop
Fasteners
WHEEL COVER
MOUNTING INSTRUCTIONS
1. Place the wheel cover in position to cover the wheel
opening and mark the locations of the button sockets.
2. With a 1/8" drill bit, pilot drill a shallow hole at each
marked location and install a twist fastener (provided in
plastic bag).
3. Install the wheel cover by snapping onto the twist
fasteners and turning fastener one quarter turn.
4. Take the 3 inch pieces of hook and loop strip; remove
peel strip and stick them onto the screen room skirting
opposite the hook and loop strips on the wheel cover (see
FIG. 7).
8. Align skirt at floor and wall of camper. Locate positions
of twist fasteners and mark with pencil. Drill 1/8" holes
and install twist fasteners.
9. Attach skirt to camper using twist fasteners just installed. If needed, locate wheel skirt over wheel well and
install using hook & loop fastener strips and twist fasteners.
10.Secure bottom of panels by driving the hook stakes into
the ground through the appropriate grommet. (See FIG.
6)
11.Attach skirt to Screen Room with hook and loop fasteners
sewn into room and skirt (see FIG. 6)
FIG. 7
Do not operate appliances venting into this
room enclosure with privacy panels closed.
At least one panel must be open for ventilation when using appliances. Death or series
injury from Carbon Monoxide Poisoning
could occur if not operated properly.
4
Loading...