Dometic TRAVELER LITE 210 Owner's Manual

1

TRAVELER LITE

®

FINE CHINA TOILET

OWNER’S MANUAL

Traveler Lite® Toilet Model 210

Dometic Corporation • Sanitation Systems

13128 State Rt 226, PO Box 38, Big Prairie, OH 44611

SeaLand Product Hotline [phone]

(8:00 a.m. - 5:00 p.m. ET)

2

1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain opening types,
in the system. These products damage the seals in toilets and dump valves.

2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to
be flushed through the toilet.

3. Mechanical seal toilets, like SeaLand Traveler Lite units, are designed to only discharge
directly into a holding tank. Horizontal pipe runs as found in conventional residential or
commercial plumbing systems cannot be accommodated.

4. Toilet bowl and flush seals must be regularly cleaned and winterized according to “Proper
Cleaning and Maintenance” and “Winterizing” procedures on page 4, or your warranty
coverage may be voided.

IMPORTANT INFORMATION

TABLE OF CONTENTS

Important Information ............................... 2

Toilet Model Identification ......................... 2

How to Use ............................................... 2

Installation ................................................ 3

Proper Cleaning and Maintenance ........... 4

Winterizing ............................................... 4

Deodorants and Special Tissue ................ 5

Troubleshooting ................................... 6 - 7

Warranty ................................................... 8

To prepare the Traveler Lite toilet for use, check to be sure water supply to the toilet is
connected. Turn on water supply and check system for leaks. Flush toilet and check for
leaks.

To properly use the Traveler Lite toilet, follow these simple instructions:

1. To add water to the toilet, lift or raise the flush lever until desired water level is reached.
Generally, more water is required only when flushing solids.

2. To flush toilet, push lever all the way down until contents leave toilet bowl. Water flow
pressures vary at different locations, therefore holding the flush lever down for 4-8
seconds may be required. We require a minimum flow at the toilet of two gpm (7.6 lpm)
for proper rim and bowl wash.

3. Release flush lever by allowing it to snap back, which permits positive sealing around the
flush ball.

4. A small amount of water should remain in bowl.

Note: Holding flush lever down longer than necessary results in excessive water usage.

HOW TO USE

TOILET MODEL IDENTIFICATION

DOMETIC CORPORATION

P.O. BOX 38, 13128 STATE RT 226 [phone]
BIG PRAIRIE, OH 44611 USA

MODEL NO.

000

SERIAL NUMBER

000000

The model identification label is located on the
toilet base and will show the model number
and serial number. Remove base cover to
locate identification label (see page 3).

3

INSTALLATION

1. To replace an older toilet, turn off water supply to toilet.
Disconnect water line at toilet water valve. Unscrew floor
bolt nuts and remove toilet. Discard old floor seal and
mounting bolts. The old floor flange may be used if it is in
good condition.

2. When installing new floor flange, make certain that the
toilet mounting bolts align properly with Traveler Lite toilet
mounting pattern (Figure A).

3. Secure flange to floor using flat head screws through
countersunk holes in flange. Insert floor bolts into slotted
holes in flange (Figure A).

4. If toilet is being installed in a shower stall, apply a 1/4"
thick by 3/4" wide bead of glazing compound around the
circumference of the floor flange (Figure B).

5. Position floor seal by pressing the floor bolts up through
holes in the seal.

6. Set toilet in place with bolts protruding up through
mounting holes in base (Figure C).

7. Install washers and hex nuts provided with toilet. Snug
nuts down equally with standard 7/16" open end wrench.
Remove excess glazing compound from around base in
shower stall installation. Install two wood screws provided
in two holes at rear of base. (See Figure C).

8. Remove pedal cover from flush pedal before connecting
water supply line (see instructions below). Connect water
supply line to water valve (1/2" MPT) inlet using
appropriate fittings or an extension (Figure D).

9. Turn on water supply and flush toilet to test for leaks.

10. Re-attach pedal cover to flush pedal after making sure
there are no leaks at connections.

11. Put base cover in front of toilet base, aligning flush pedal
with opening on side of cover. Push base cover back until
it locks into place, making sure it does not interfere with
flush pedal operation (Figure E).

Fig. B

Traveler Lite

Model 210

(2-bolt

connection)

Insert
two
wood
screws
in rear
of base.

Fig. A

Fig. C

Fig. D

Fig. E

Removing Pedal Cover

1. Press tab on back of

pedal to release pedal
cover.

2. Pull cover forward to

remove it. Cover snaps
back into place.