Dodge ZB Viper 2005 User Manual

SECTION PAGE

1

INTRODUCTION

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4

UNDERSTANDING YOUR INSTRUMENT PANEL

5

STARTING AND OPERATING

6

WHAT TO DO IN EMERGENCIES

7

MAINTAINING YOUR VEHICLE

8

MAINTENANCE SCHEDULES

9

IF YOU NEED CONSUMER ASSISTANCE

TABLE OF CONTENTS

.............................................................3

..............................9

..............................53

....................................83

.................................................109

..............................................147

...............................................157

..................................................217

.........................................233

1

2

3

4

5

6

7

8

9

10

INDEX

....................................................................243

10

CONTENTS

INTRODUCTION

1

䡵 Introduction ........................... 4

䡵 How To Use This Manual ..................4

䡵 Warnings And Cautions ................... 6

䡵 Vehicle Identification Number ............... 6

䡵 Vehicle Modifications / Alterations ........... 7

4 INTRODUCTION

INTRODUCTION

This manual has been prepared with the assistance of
service and engineering specialists to acquaint you with
the operation and maintenance of your new vehicle. It is
supplemented by a Warranty Information Booklet and
various customer oriented documents. You are urged to
read these publications carefully. Following the instruc­tions and recommendations in this manual will help
assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored
in the vehicle for convenient reference and remain with
the vehicle when sold, so that the new owner will be
aware of all safety warnings.

When it comes to service, remember that your dealer
knows your vehicle best, has the factory-trained techni­cians and genuine Mopar威 parts, and is interested in
your satisfaction.

WARNING!

Engine exhaust, some of its constituents, and certain
vehicle components contain or emit chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. In addition, cer­tain fluids contained in vehicles and certain products
of component wear contain or emit chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section
contains the information you desire.

The detailed index, at the rear of this manual, contains a
complete listing of all subjects.

Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this owner’s manual:

INTRODUCTION 5

1

6 INTRODUCTION

WARNINGS AND CAUTIONS

This manual contains WARNINGS against operating
procedures which could result in an accident or bodily
injury. It also contains CAUTIONS against procedures
which could result in damage to your vehicle. If you do
not read this entire manual you may miss important
information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The vehicle identification number (VIN) is on a stamped
plate at the left front corner of the instrument panel,
visible through the windshield. This number also ap­pears on the Automobile Information Disclosure Label
affixed to a window on your vehicle. Save this label as a
convenient record of your vehicle identification number
and optional equipment.

Vehicle Identification Number

VEHICLE MODIFICATIONS / ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle
could seriously affect its roadworthiness and safety
and may lead to an accident resulting in serious
injury or death.

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵 A Word About Your Keys ..................11

▫ Ignition Key ..........................11

▫ Key-In-Ignition Reminder ................12

▫ Power Accessory Delay Feature ............13

䡵 Door Locks ............................13

▫ Electronic Locking/Unlocking .............13

▫ Mechanical Release .....................14

▫ Automatic Door Locks ...................15

䡵 Remote Keyless Entry .....................15

2

▫ To Unlock The Doors ...................16

▫ To Lock The Doors .....................17

▫ To Unlock The Trunk ....................17

▫ Panic Alarm ..........................17

▫ To Use The Panic Alarm .................17

▫ To Program Transmitters .................18

▫ General Information ....................18

▫ Transmitter Battery Service ...............19

䡵 Vehicle Theft Alarm ......................20

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ To Arm The Vehicle Theft Alarm System ......20

▫ Entering The Trunk With The System Armed . . .21

▫ Security System Disarm ..................22

▫ Tamper Alert .........................23

䡵 Trunk Safety Warning .....................23

▫ Trunk Internal Emergency Release ..........24

䡵 Windows .............................24

▫ Power Windows .......................24

▫ Auto Down Feature ....................26

▫ Power Accessory Delay Feature ............26

▫ Wind Buffeting ........................26

䡵 Occupant Restraints ......................26

▫ Lap/Shoulder Belts .....................27

▫ Enhanced Driver Seat Belt Reminder System

(BeltAlert) ...........................31

▫ Six Point Belt System - If Equipped .........32

▫ Seat Belts And Pregnant Women ............33

▫ Seat Belt Extender ......................33

▫ Child Restraint ........................34

▫ Supplemental Restraint System (SRS) - Airbag . .41

䡵 Engine Break-In Recommendations ...........50

䡵 Safety Tips ............................51

▫ Exhaust Gas ..........................51

▫ Safety Checks You Should Make Inside The

Vehicle ..............................51

▫ Safety Checks You Should Make Outside The

Vehicle ..............................52

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

A WORD ABOUT YOUR KEYS

The dealer that sold you your new Viper has the key code
numbers for your vehicle locks. These numbers can be
used to order duplicate keys from your dealer or a
locksmith. Ask your dealer for these numbers and keep
them in a safe place.

Ignition Key

2

Ignition Key Positions

Press clutch and insert the ignition key fully, then turn
the switch to one of the four illustrated positions. It may
be difficult to turn the key from the OFF/LOCK position
when starting your vehicle. Move the steering wheel left
and right while turning the key until it turns easily. To

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

start the vehicle fully apply the parking brake, press the
clutch pedal to the floor, place the gear selector in
NEUTRAL, move the key to the ON position, and press
the red ENGINE START button located on the instrument
panel. To remove the key from the ignition press the
clutch pedal to the floor, bring the vehicle to a stop, place
the gear selector in gear, and fully apply the parking
brake. Then turn the ignition key to the OFF/LOCK
position and push the release button behind the ignition
and pull the key out.

Engine Start Button

Key-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition,
sounds a signal to remind you to remove the key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

Power Accessory Delay Feature

The Power Accessory Delay feature provides the cus­tomer with the ability to operate the power windows,
and the radio for 2 minutes after the ignition switch is
turned off. If the key is removed from the ignition and the
driver door is opened prior to the completion of the
2–minute timer, the feature is immediately cancelled. The
Power Accessory Delay feature is initially enabled, but
may be enabled or disabled at the dealership.

DOOR LOCKS

WARNING!

2

Do not touch the exhaust pipe sill covers when
entering or exiting your Viper. They can be hot
enough to burn you. Observe the warning labels on
each door closure panel.

Electronic Locking/Unlocking

This vehicle is equipped with a virtual lock system. If the
vehicle is virtually locked, then the Outside door handle
is ignored. There is a door lock/unlock switch on each
door trim panel. Press this switch to lock or unlock the
door. The Odometer displays DOOR UNLOCKED con­tinuously when both doors are unlocked. Also, the door
is considered unlocked if the inside door handle is
pulled. If only one door is unlocked, then the Odometer

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

will flash DOOR UNLOCKED every 2 seconds. After
about 40 seconds with the ignition off, the display will
turn off.

NOTE: If you attempt to lock the doors with the key in
the ignition and the driver’s door open, the doors will not
lock.

Power Door Lock Switch

Mechanical Release

The driver’s door can be opened mechanically by insert­ing your key into the lock located on the underside of the
door panel, beneath the outside mirror.

Mechanical Door Lock

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

Automatic Door Locks

The doors will lock automatically from outside the ve­hicle when vehicle speed reaches 18 miles per hour with
the ignition On and the DOOR UNLOCKED displayed in
the odometer will disappear.

NOTE: If the vehicle is moving faster than 5 MPH, the
inside and outside door handles are ignored. This does
not overide the mechanical cable on the inside door
handle.

Automatic lock can be enabled or disabled by performing
the following procedure:

1. Close all doors and place the key in the ignition.

2. Cycle the ignition switch between ON/RUN and OFF
4 times ending up in the OFF position.

3. Depress the power door lock switch to lock the doors.

4. A single chime will indicate the completion of the
programming and that the feature was toggled ON/OFF.

This feature can also be disabled at the dealership if
desired.

REMOTE KEYLESS ENTRY

This feature allows you to lock or unlock the doors from
distances up to 23 feet (7 meters) using a hand held
transmitter. You do not have to point the transmitter at
the vehicle to activate the system.

Keyless Entry Transmitter

2

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Unlock the Doors:

Press and release the UNLOCK button on the transmitter.
The front and rear park/turn signal lights will blink once
to indicate that only the driver’s door is unlocked. When
the unlock button is pressed twice, if pressed within 5
seconds, the front and rear park/turn signal lights will
blink twice to indicate that both doors are unlocked.
DOOR UNLOCKED in the odometer display will blink
continuously if one door is unlocked. DOOR UN­LOCKED will remain steadily on in the odometer display
if both doors are unlocked. No message will be displayed
if both doors are locked.

NOTE: The system may be programmed to unlock both
doors upon the first press of the Unlock button. To toggle
between the first press unlock of the driver’s door to
unlock both doors, perform the following procedure:

1. Press and hold the Unlock button on the transmitter.

2. Continue to hold the Unlock button, wait at least 4 but
no longer than 10 seconds, then press the Lock button.

3. Release both buttons.

The park and tail lights will blink twice to acknowledge
the unlock signal.

NOTE: The Lamp Flash can be enabled or disabled by
performing the following procedure:

1. Press and hold the Lock button on the transmitter.

2. Continue to hold the Lock button, wait at least 4 but
no longer than 10 seconds, then press the Trunk button.

3. Release both buttons.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

To Lock the Doors:

NOTE: To enable/disable the Lamp Flash, see proce­dure described above.

Press and release the LOCK button on the transmitter.
The horn will chirp once and the park and tail lights will
blink to acknowledge that the door is locked and that the
alarm system is armed. The horn chirp can be disabled at
the dealership if so desired.

NOTE: The horn chirp feature can be enabled or dis­abled by performing the following procedure:

1. Press and hold the Lock button on the transmitter.

2. Continue to hold the Lock button, wait at least 4 but
no longer than 10 seconds, then press the Unlock button.

3. Release both buttons.

To Unlock the Trunk:

Press and hold the trunk button on the transmitter to
unlatch the trunk. The front and rear park/turn signal
lights will blink 3 times.

Panic Alarm

The panic alarm unlocks the driver’s door, turns on the
interior lights, flashes the park and fog lights and sounds
the horn for 3 minutes or until the alarm is turned off.
Panic mode does not work when the vehicle is driven.

To Use the Panic Alarm:

Press and hold the Panic button to activate the alarm.
Press and hold the Panic button or turn the key in the
ignition to the RUN position to deactivate the alarm. The
alarm will also shut itself off after 3 minutes.

2

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Program Transmitters:

This feature allows you to program transmitters in case
one is lost or an extra transmitter(s) is desired. Up to 4
transmitters can be programmed to your vehicle. To
program another transmitter follow these steps:

1. Turn the ignition switch to the ON/RUN position and
set the parking brake.

2. Using a previously programmed transmitter, press the
UNLOCK button for 5 to 10 seconds. While the UNLOCK
button is being pressed (after 5 seconds), press the
PANIC button and release both buttons simultaneously.
You will hear a chime sound to signal you that program­ming on the transmitter(s) may occur.

3. You may program up to 4 transmitters for your vehicle
within a 30 second time limit. Press and release both
LOCK and UNLOCK buttons of a new transmitter at the
same time; then press and release any of the buttons
once, you will hear a chime when the transmitter has

been successfully programmed. A chime will sound
when the 30 seconds is over, or if you turn the ignition
switch OFF.

4. You must repeat step 3 for all new transmitters that
will be used with this vehicle (up to 4 total).

If you do not have a programmed transmitter, contact
your dealer for details.

General Information

This transmitter complies with FCC rules part 15. Opera­tion is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may be
received, including interference that may cause undes­ired operation.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

Transmitter Battery Service

The replacement battery number is 2016. This is a generic
battery, readily available at local retail stores.

1. Pry the transmitter halves apart with a coin or similar
object.

Separating Transmitter Halves

2. Remove and replace the batteries.

3. Reassemble the transmitter case and test operation.

NOTE: If the transmitter is operated more than 255
times out of range of the vehicle (23 feet or 7 meters) or
when the vehicle battery is dead, it may become “out of
synch”. The result is that the transmitter will not func­tion.

To correct this condition, remove the key from the
ignition and close the hood and all doors. Press both
buttons on the transmitter for about 10 seconds. The horn
will chirp once to acknowledge the signal. Normal trans­mitter operation should resume.

2

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

VEHICLE THEFT ALARM

The system monitors the doors, trunk, hood, and ignition
for unauthorized operation.

Once the system has been armed, opening any door,
trunk (with the ignition key), hood or turning the ignition
key to any position will trigger an alarm.

If something triggers the alarm, the system will signal for
about 18 minutes. For the first 3 minutes the horn will
sound and the park, tail and fog lights will flash. If the
condition which triggered the alarm is still present, the
park, tail and fog lights will continue to flash for 15
minutes, unless the trigger condition is cleared sooner.

NOTE: The engine will not start until the system is
disarmed.

To Arm the Vehicle Theft Alarm System

There are two methods to arm the Vehicle Theft Alarm
system:

1. Press the Lock button on the Remote Keyless Entry.
The optical and audible horn chirp will sound if it is
enabled. (See Remote Keyless Entry section of this
manual)

2. Remove the keys from the ignition and, with the door
open, press the Lock button on the door trim panel and
close the door.

3. After the last door is closed, the security light will
flash for 15 seconds. If there is a fault in the system or if
the hood or trunk is not closed, the Vehicle Theft Alarm
lamp will remain ON steady for 15 seconds until the
system is armed. (See the dealer if the system is faulted)
The arming sequence will cancel if the door is opened or
the ignition is turned on. Opening the hood or trunk will
not cancel the arming process.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

CAUTION!

Security Alarm Light

4. The Security light will periodically flash, once every 6
seconds, to show that the system is still armed.

If the Security lamp flashes twice every 6 seconds,
then the vehicle was tampered with!

Entering the Trunk with the System Armed

To enter the trunk with the system armed, the Remote
Keyless Entry Trunk button must be pressed. This will
pop the trunk open and allow access without alarming or
disarming the Vehicle Theft Alarm System.

NOTE: If the key is used and the system is armed, then
the Vehicle Theft Alarm System will start alarming.

2

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Security System Disarm

There are two ways to disarm the system:

1. Driver door key cylinder: Insert the key in the cylinder
located under the driver’s door mirror. This will disarm
the Vehicle Theft Alarm System and open the driver’s
door.

Mechanical Door Lock

2. Or, press the UNLOCK button on the Remote Keyless
Entry transmitter. The front and rear park and turn signal
lights will flash to acknowledge the signal. (See the
Remote Keyless Entry Section of this manual for opera­tion)

Keyless Entry Transmitter

NOTE: The vehicle will not start unless the Vehicle

Theft Alarm System is disarmed by either of the two
methods above. Inserting the key in the ignition WILL
NOT disarm the system (it will start the alarming pro­cess!)

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

Tamper Alert

If the horn sounds 3 times when you unlock the vehicle
using the Remote Keyless Entry transmitter or key, the
alarm has been activated. Check the vehicle for tamper­ing.

NOTE: If the Security lamp flashes twice every 6
seconds, then the vehicle was tampered with.

TRUNK SAFETY WARNING

WARNING!

2

Do not allow children to have access to the trunk,
either by climbing into the trunk from outside, or
through the inside of the vehicle. Always close the
trunk lid when your vehicle is unattended. Once in
the trunk, young children may not be able to escape.
If trapped in the trunk, children can die from suffo­cation or heat stroke.

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Trunk Internal Emergency Release

Emergency Release

NOTE: As a security measure, a Trunk Internal Emer-

gency Release lever is built into the trunk latching
mechanism. In the event of an individual being locked
inside the trunk, the trunk can simply be opened by

pulling on the lever attached to the trunk latching
mechanism, which is coated so that it glows in a dark­ened trunk.

WINDOWS

Power Windows

The power window switches are located between the
driver and passenger seats on the center tunnel bezel, just
to the left of the parking brake. The switch on the left side
controls the driver’s window and the switch on the right
controls the passenger’s window. The power window
switches are active when the ignition is in RUN or
ACCESSORY.

The power window switch also works during accessory
delay. This delay feature will allow the windows to be
functional up to 2 minutes after the vehicle has been
turned off. This feature can be disabled at the dealership
if desired.

NOTE: Windows cannot be driven up during accessory
delay with a door open.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

NOTE: If the windows are completely closed, each
respective window will drop slightly when either door is
opened. The windows return to their full up position
when the door is again closed. This is necessary to clear
the seal when either door is opened.

WARNING!

Never leave children in a vehicle, with the keys in
the ignition switch. Occupants, particularly unat­tended children, can become entrapped by the
power windows while operating the power window
switch. Such entrapment may result in serious injury
or death.

2

Power Window Switches

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Auto Down Feature

Both windows have an auto down feature. Press the
window switch to the second detent, release, and the
window will go down automatically. Press the switch a
second time in either direction to stop the window.

To open the window to a desired position, press and hold
the window switch in the first detent until the window
has reached the desired position and then release it when
you want the window to stop.

Power Accessory Delay Feature

The Power Accessory Delay feature provides the cus­tomer with the ability to operate the power windows,
and the radio for 2 minutes after the ignition switch is
turned off. If the key is removed from the ignition and the
driver door is opened prior to the completion of the
2–minute timer, the feature is immediately cancelled. The
Power Accessory Delay feature is initially enabled, but
may be enabled or disabled at the dealership.

NOTE: The Window Up switch will not function with
the door open and while the system is in the Power
Accessory Delay mode. If the window is in the process of
going up, opening the door will stop the window move­ment immediately.

Wind Buffeting

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter-type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the top down. This is a normal
occurrence and can be minimized.

OCCUPANT RESTRAINTS

One of the most important safety features in your Viper
is the restraint system. This system consists of the driv­er’s and passenger’s seat belts, airbags for the driver and
passenger, and a passenger airbag on/off switch located
in the center console compartment for deactivating the
passenger airbag system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

Please pay close attention to the information in this
section. It tells you how to use your restraint system
properly to keep you and your passenger as safe as
possible. Whichever system you have, all of the warnings
in this section apply.

WARNING!

In a collision, you and your passenger can suffer
much greater injuries if you are not properly buck­led up. You can strike parts of the inside of your
vehicle or your passenger, or you can be thrown out
of the vehicle. Always be sure you and your passen­ger are buckled up properly.

Buckle up even though you are an excellent driver. Even
on short trips. Someone on the road may be a poor driver
and cause a collision that includes you. And this can
happen far away from home or on your street.

Research has shown that seat belts save lives. They also
can reduce the seriousness of injuries in a collision. Some
of the worst injuries happen when people are thrown
from the vehicle. Seat belts provide protection against
that, and they reduce the risk of injury caused by striking
the inside of the vehicle. Everyone in a motor vehicle
needs to be buckled up all the time.

Lap/Shoulder Belts

Each seat belt is a combined lap/shoulder belt system.
The belt webbing retractor will lock only during very
sudden stops or impacts. This feature allows the shoulder
part of the belt to move freely with you under normal
conditions. But, in a collision, the belt will lock and
reduce the risk of your striking the inside of the vehicle or
being thrown out.

2

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Wearing a seat belt incorrectly is dangerous. Seat
belts are designed to go around the large bones of
your body. These are the strongest parts of your body
and can take the forces of a collision the best.
Wearing your belt in the wrong place could make
your injuries in a collision much worse. You might
suffer internal injuries, or you could even slide out
of part of the belt. Follow these instructions to wear
your seat belt safely and to keep your passengers
safe, too.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the seat.

2. The seat belt latch plate is located at the side of your
seat back. Grasp the latch plate and pull out the belt.

Latch Plate

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

3. Slide the latch plate up the webbing as far as necessary
to make the belt go around your lap.

Latch Plate To Buckle

4. When the belt is long enough to fit, insert the latch
plate into the buckle until you hear a “click.”

WARNING!

A belt that is too loose will not protect you as well. In
a sudden stop you could move too far forward,
increasing the possibility of injury. Wear your seat
belt snugly.

A belt that is worn under your arm is very danger­ous. Your body could fall into the inside surfaces of
the vehicle in a collision, increasing head and neck
injury. And a belt worn under the arm can cause
internal injuries. Ribs aren’t as strong as shoulder
bones. Wear the belt over your shoulder so that your
strongest bones will take the force in a collision.

2

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

5. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap belt portion, pull up
a little on the shoulder belt, as shown.

Removing Slack From Belt

6. To loosen the lap belt if it is too tight, tilt the latch plate
and pull on the lap belt. A snug belt reduces the risk of
sliding under the belt in a collision.

WARNING!

A lap belt worn too high can increase the risk of
internal injury in a collision. The belt forces won’t
be at the strong hip and pelvic bones, but across your
abdomen. Always wear the lap belt as low as pos­sible and keep it snug.

7. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

WARNING!

A twisted belt can’t do its job as well. In a collision
it could even cut into you. Be sure the belt is straight.
If you can’t straighten a belt in your vehicle, take it
to your dealer and have it fixed.

8. To release the belt, push the red button marked PRESS
on the buckle. The belt will automatically retract to its
stowed position. If necessary, slide the latch plate down
the webbing to allow it to retract fully.

Enhanced Driver Seat Belt Reminder System
(BeltAlert)

If the driver’s seat belt has not been buckled within 60
seconds of starting the vehicle and if the vehicle speed is
greater than 5 mph (8 km/h), the Enhanced Warning
System (BeltAlert) will alert the driver to buckle their seat
belt. The driver should also instruct all other occupants to

buckle their seat belts. Once the warning is triggered, the
Enhanced Warning System (BeltAlert) will continue to
chime and flash the Seat Belt Warning Light for 96
seconds or until the driver’s seat belt is buckled. The
Enhanced Warning System (BeltAlert) will be reactivated
if the driver’s seat belt is unbuckled for more than 10
seconds and the vehicle speed is greater than 5 mph (8
km/h).

The Enhanced Warning System (BeltAlert) can be en­abled or disabled by your authorized dealer or by
following these steps:

NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recom­mend deactivating the Enhanced Warning System
(BeltAlert).

1. Turn the ignition switch to the OFF position and
buckle the driver’s seat belt.

2

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Start the engine and wait for the Seat Belt Warning
Light to turn off.

3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver’s seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.

NOTE: Watch for the Seat Belt Warning Light to turn on
while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt.

4. Turn off the engine. A single chime will sound to
signify that you have successfully completed the pro­gramming.

The Enhanced Warning System (BeltAlert) can be reacti­vated by repeating this procedure.

NOTE: Although the Enhanced Warning System
(BeltAlert) has been deactivated, the Seat Belt Warning
Light will continue to illuminate while the driver’s seat
belt remains unbuckled.

Six Point Belt System - If equipped

This six point belt system meets SCCA standards and
should be only used when engaged in related perfor­mance driving events. The standard lap/shoulder belt
should be used whenever the vehicle is operated on the
street.

Six Point Belt Operating Instructions

With the anti-submarining belt placed on the seat point­ing up, buckle the left and right lap belts and strap both
legs. Buckle the left and right shoulder belts. Adjust the
belts by pulling on the web ends and/or re-positioning
the web clips and straps as required. Release the belts by

1

turning the belt latch mechanism

⁄4turn in either the

clockwise or counter-clockwise direction.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

NOTE: The anti-submarining belt and the shoulder belt
are attached to eye bolts at designated locations and
should be removed from the vehicle when not in use. The
lap belts and straps can be stored behind or to the sides
of the seat after removal.

Seat Belts and Pregnant Women

We recommend that pregnant women use the seat belts
throughout their pregnancy. Keeping the mother safe is
the best way to keep the baby safe.

Pregnant women should wear the lap part of the belt
across the thighs and as snug across the hips as possible.
Keep the belt low so that it does not come across the
abdomen. That way the strong bones of the hips will take
the force if there is a collision.

Seat Belt Extender

If a seat belt is too short, even when fully extended, your
dealer can provide you with a seat belt extender. This
extender should be used only if the existing belt is not
long enough.

WARNING!

A frayed or torn belt could rip apart in a collision
and leave you with no protection. Inspect the belt
system periodically, checking for cuts, frays, or loose
parts. Damaged parts must be replaced immediately.
Do not disassemble or modify the system. Seat belt
assemblies must be replaced after an accident if they
have been damaged (bent retractor, torn webbing,
etc.)

2

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Child Restraint

Everyone in your vehicle needs to be buckled up all the
time, babies and children, too.

WARNING!

In a collision, an unrestrained child, even a tiny
baby, can become a missile inside the vehicle. The
force required to hold even an infant on your lap
could become so great that you could not hold the
child, no matter how strong you are. The child and
others could be badly injured. Any child riding in
your vehicle should be in a proper restraint for the
child’s size.

All states and Canadian provinces require small
children to ride in proper restraint systems. This is
the law, and you can be prosecuted for ignoring it.

Infants and Small Children

There are two different sizes and types of restraints for
children from newborn size to the bigger child almost
large enough for an adult seat belt. Always check the
child seat owner’s manual to ensure you have the right
seat for your child. Use the restraint system that is correct
for your child.

Two different child restraint systems are generally avail­able:

•

The infant carrier for babies weighing up to approxi­mately 20 lbs. (9 kg).

•

The child seat for small children over 20 lbs. (9kg).

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

WARNING!

A rearward facing infant restraint must not be used
in your Viper unless the passenger airbag has been
shut off. A rearward facing infant restraint may be
struck by a deploying passenger airbag which may
cause severe or fatal injury to the infant.

In addition, some manufacturers make systems that can
be first used as an infant carrier, then converted to a child
seat as the child grows.

Here are some tips on getting the most out of your child
restraint.

Before buying any restraint system, make sure that it has
a label certifying that it meets Motor Vehicle Safety
Standard 213. The manufacturer also recommends that
before you buy a child restraint, you try it in the seat
where you will use it.

The restraint must be appropriate for your child’s weight
and height. Check the label on the restraint for this too.

Carefully follow the instructions that came with the
restraint. If you install the restraint improperly, it may not
work when you need it.

WARNING!

Improper installation can lead to failure of a child
restraint. It could come loose in a collision. The child
could be badly injured or killed. Follow the manu­facturer’s directions exactly when installing a child
restraint.

•

Child restraints are secured in the passenger seat by
the lap part of the lap/shoulder belt.

2

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Buckle the child into the seat exactly as the child seat
manufacturer’s directions tell you. The latch plate on the
lap/shoulder belt will keep the belt tight.

When your infant carrier or child seat is not in use, secure
it with the seat belt or remove it from the vehicle. Don’t
leave it loose in the vehicle. In a sudden stop or collision,
it could strike occupants and injure them.

LATCH — Lower Anchors and Tether for CHildren

LATCH Anchorages

Your vehicle’s passenger seat is equipped with the child
restraint anchorage system called LATCH, which stands
for Lower Anchors and Tether for Children. The LATCH

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

system provides for the installation of the child restraint
without using the vehicle seat belt. The passenger seat
has an exclusive lower anchorage.

These are round bars, located at the lower area of the seat
back, one on each side of the passenger seat. You will
easily feel them if you run your finger along the inter­section of the surface. Install your child seat as per child
seat manufacturer recommendations.

NOTE: If your child restraint seat is not LATCH com­patible, install the restraint using the vehicle seat belts.

Child Restraint Tether Anchor

Child restraints having tether straps and hooks for con­nection to tether anchors have been available for some
time. In fact, many child restraint manufacturers will
provide add-on tether strap kits for some of their older
products. There is a tether strap anchor located in the
child tether access cover behind the passenger seat.

Remove the child tether access cover by prying either
side with a screwdriver or similar tool, as shown in
illustration which follows. While the child tether is in
use, keep the access cover in a safe place so that it can be
replaced after use of the child tether.

Child Tether Access Cover

2

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To attach the tether strap to the anchor, move the
seatback fully forward. Pass the child restraint tether
hook through either opening in the seatback under the
head restraint. Attach the tether hook to the anchor loop,
recline the seatback full rearward and move the seat to its
most rearward position. Install the child restraint accord­ing to the manufacturer’s directions. Return the seatback
to an upright position. Remove slack from the tether
strap according to the child restraint manufacturer’s
directions.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

WARNING!

An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchor position directly behind
the child seat to secure a child restraint top tether
strap.

Installing Child Restraints Using the Vehicle Seat
belt

The passenger side seat belt is equipped with an auto­matic locking retractor for child restraint system installa­tion. It is designed to keep the lap portion of the restraint
tightly held to the passenger seat. Seat belts equipped
with automatic locking retractors will have a distinctive
label on the webbing.

To restrain the child seat, pull enough webbing from the
retractor to allow the belt to pass through the child

restraint and slide the latch plate into the buckle. Then,
pull on the webbing from the retractor until all of it is
extracted. Retract some to the webbing back to the
retractor to activate the automatic locking retractor. (See
Seat Belt Locking Mode below). Tighten the lap portion
of the belt and allow the excess webbing to retract back to
the retractor. If it still does not make the child restraint
secure, try different seating positions in addition to
securing the child restraint with the LATCH restraint
system.

Seat Belt Locking Mode

The seat belts for both occupants are equipped with
emergency locking retractors for normal use. They are
activated during very sudden stops or impacts and are
set in emergency locking mode. However, the passenger
side seat belt is also equipped with an automatic locking
retractor to secure child restraint systems. It can also be
converted to set the seat belt in the emergency locking
mode.

2

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To convert the emergency locking mode to automatic
locking mode for seat belts equipped with automatic
locking retractors, grasp on the shoulder belt portion of
the belt and pull all of the webbing out of the retractor. By
allowing some of the webbing to retract back into the
retractor, you will hear a clicking sound indicating that
the belt is now activated to automatic locking mode.

Once it is in the automatic locking mode you will not be
able to pull any more of the webbing out of the retractor,
but will only be able to feed back excess webbing to
secure the child restraint. To disengage the automatic
locking mode, simply allow all of the webbing to retract
back into the retractor which will switch the seat belt to
emergency locking mode for normal use.

Children Too Large For Child Seats

Children who are too large for child seats and who can sit
upright by themselves should use the lap/shoulder belt
for best protection.

•

Make sure that the child is seated upright in the seat.

•

The lap belt should be low on the hips and as snug as
possible.

•

Check belt fit periodically. A child’s squirming or
slouching can move the belt out of position.

•

If the shoulder belt contacts the face or neck, move the
child closer to the side of the vehicle.

Booster seats that may help overcome this problem are
also available for use with lap/shoulder belts. Before
buying a booster seat, make sure that it has a label
certifying that it meets applicable Motor Vehicle Safety
Standards. Make sure that it is satisfactory for use in this
vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

Supplemental Restraint System (SRS) - Airbag

This vehicle has airbags for the driver and passenger as a
supplement to the seat belt restraint systems. The driver’s
airbag is mounted in the steering wheel. The passenger
side airbag is mounted in the instrument panel, under a
cover marked SRS/AIRBAG. These airbags inflate in
higher speed impacts. They work with the instrument
panel knee bolsters and the seat belts to provide im­proved protection for the driver and right front passen­ger.

WARNING!

•

Relying on the airbags alone could lead to more
severe injuries in a collision. The airbags work
with your seat belt to restrain you properly. In
some collisions the airbags won’t deploy at all.
Wear your seat belts even though you have air­bags.

•

Being too close to the steering wheel or instru­ment panel during airbag deployment could cause
serious injury. Airbags need room to inflate. Sit
back, comfortably extending your arms to reach
the steering wheel or instrument panel.

The seat belts are designed to protect you in many types
of collisions. The airbags deploy only in frontal collisions
and will not deploy in collisions at slow speed. But even

2

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

in collisions where the airbags deploy, you need the seat
belts to keep you in the right position for the airbags to
protect you properly.

Here are four simple steps you can take to minimize the
risk of harm from a deploying airbag.

1. Infants in rear facing child safety seats designed for

children up to one year or approximately 20 pounds (9
kg) should never ride in the front seat of a vehicle with
a passenger side airbag unless the airbag is shut OFF.

See “Passenger Side Airbag On/Off Switch.” An airbag
deployment can cause severe injury or death to infants in
this position.

Children that are not big enough to properly wear the
vehicle seat belt (see section on “Child Restraint”) should
be secured in child safety seats or booster seats.

Older children who do not use child safety seats or
booster seats should ride properly buckled.

Never allow children to place the shoulder belt behind
them or under the arm.

Infants up to 1 year or approximately 20 pounds (9 kg)
should never ride in the vehicle, because the rear facing
child seat places them too close to the passenger air bag
in the event of a crash.

Children from 1 to 12 years old: Move the passenger seat
as far back as possible. Children from 20 to 60 pounds (9
kg to 27 kg) should be secured in the appropriate child
safety seat or booster seat. If too large for a booster seat,
the child should wear the lap/shoulder belt properly.
Children should never be allowed to lean forward to­ward the instrument panel as a passenger air bag deploy­ment could cause severe injury or death to a child in this
position.

You should read the instructions provided with your
child restraint to make sure that you are using it properly.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

2. All occupants should wear their lap and shoulder
belts properly.

3. The driver and passenger seats should be moved
back as far as practical to allow the airbags room to
inflate. Additionally, the pedals are power adjustable,
so the driver seat can be moved back and the pedals
moved closer as needed so the driver can be as far from
the airbag as possible. (See section on Power Adjust­able Pedals for operation.)

4. You should read the instructions provided with your
child safety or booster seat to make sure that you are
using it properly.

The airbag system consists of the following:

•

Airbag control module and internal crash sensor

•

AIRBAG Readiness Light

•

Driver and Passenger Airbag/inflator Units

•

Passenger Side Airbag On/Off Switch

•

Passenger Airbag Off Indicator Light

•

Unique Steering Wheel and Column

•

Unique Instrument Panel

•

Interconnecting Wiring

•

Knee Impact Bolster

2

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

How The Airbag System Works

A crash sensor in the occupant compartment deter-

•

mines if a frontal impact is severe enough to require
the airbag. The sensor will not detect side, roll over, or
rear impacts. The crash sensor is connected to the
diagnostic unit and to the airbag/inflator unit.

•

The Diagnostic Unit monitors the readiness of the
electronic parts of the system whenever the ignition
switch is in the START or RUN position. These include
all of the items listed above except the knee bolster, the
instrument panel, and the steering wheel and column.
The Diagnostic Unit also turns on the AIRBAG light in
the instrument panel for 6 to 8 seconds when the
ignition is first turned on, then turns the light off. If it
detects a malfunction in any part of the system, it turns
on the light either momentarily or continuously.

•

The Airbag/Inflator Units are in the center of the
steering wheel and in the instrument panel. The words
SRS/AIRBAG are embossed on the airbag covers.

WARNING!

Ignoring the AIRBAG light in your instrument panel
could mean you won’t have the airbags to protect
you in a collision. If the light does not come on, stays
on after you start the vehicle, or if it comes on as you
drive, have the airbag system checked right away.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

WARNING!

Do not put anything on or around the airbag covers
or attempt to manually open them. You may damage
the airbags and you could be injured because the
airbags are not there to protect you. These protective
covers for the airbag cushions are designed to open
only when the airbags are inflating.

•

When the crash sensors detect an impact requiring the
airbags, they signal the inflator units. A large quantity
of non toxic nitrogen gas is generated to inflate the
airbags. The airbag covers separate and fold out of the
way as the airbags inflate to their full size. The airbags
fully inflate in about 50 milliseconds. This is only
about half of the time it takes you to blink your eyes.
The airbags then quickly deflate while helping to
restrain the driver and right front passenger. The
airbag gas is vented through the airbag material

towards the instrument panel. In this way the airbags
do not interfere with your control of the vehicle.

•

The Knee Impact Bolsters help protect the knees and
position you for the best interaction with the airbags.

If A Deployment Occurs

The airbag system is designed to deploy when the impact
sensors detect a moderate to severe frontal collision, to
help restrain the driver and right front passenger, and
then to immediately deflate.

NOTE: A frontal collision that is not severe enough to
need airbag protection will not activate the system. This
does not mean something is wrong with the airbag
system.

If you do have a collision which deploys the airbags, any
or all of the following may occur:

•

The nylon airbag material may sometimes cause abra­sions and/or skin reddening to the driver and right

2

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

front passenger as the airbags deploy and unfold. The
abrasions are similar to friction rope burns or those
you might get sliding along a carpet or gymnasium
floor. They are not caused by contact with chemicals.
They are not permanent and normally heal quickly.
However, if you haven’t healed significantly within a
few days, or if you have any blistering, see your doctor
immediately.

•

As the airbags deflate you may see some smoke-like
particles. The particles are a normal by-product of the
process that generates the non toxic nitrogen gas used
for airbag inflation. These airborne particles may irri­tate the skin, eyes, nose, or throat. If you have skin or
eye irritation, rinse the area with cool water. For nose
or throat irritation, move to fresh air. If the irritation
continues, see your doctor. If these particles settle on
your clothing, follow the garment manufacturer’s in­structions for cleaning.

•

Your vehicle may be safely driveable after the airbags
deploy. If so, you can tuck the deployed airbags inside
the opening in the steering wheel hub and instrument
panel trim covers to make driving somewhat easier.

WARNING!

Deployed airbags can’t protect you in another colli­sion. Have the airbags replaced by an authorized
dealer as soon as possible.

Passenger Side AirBag On/Off Switch

The passenger airbag is to be turned off only if the
passenger:

•

is an infant (less than 1 year old) who must ride in the
front seat because there is no rear seat, because the rear
seat is too small for a rear-facing infant restraint or

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

because the infant has a medical condition which
makes it necessary for the driver to be able to see the
infant,

•

is a child, age 1 to 12 who must ride in the front seat
because there is no rear seat, because there is no rear
seat position available, or because the child has a
medical condition which makes it necessary for the
driver to be able to see the child,

•

has a medical condition which makes passenger airbag
inflation (deployment) a greater risk for the passenger
than the risk of hitting the dashboard (instrument
panel) or windshield in a crash.

If the airbag is turned off when there is any other
occupant at that position, the supplemental restraint
provided by the airbag will not be available.

To turn OFF the passenger side airbag, use the on/off
switch located in the center console.

2

Passenger Airbag ON/OFF Switch

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: When the passenger airbag is turned off the
airbag off light will illuminate

Passenger Airbag Off Light

To Shut Off the Passenger Airbag:

•

Place only the tip of the ignition key in the on/off
switch, turn the key clockwise, and remove the key
from the switch. This will shut off the passenger side

airbag. The PASS AIRBAG OFF light on the instrument
panel will illuminate when the ignition switch is
turned to the ON position.

To Turn On The Passenger Airbag:

•

Place the ignition key in the on/off switch, turn the
key counterclockwise, and remove the key from the
switch. This will turn on the passenger side airbag.
The light on the instrument panel will be off when the
ignition switch is turned to the ON position.

WARNING!

The airbag may malfunction and serious injury
could result if key is left in the airbag shut off
switch. Always remove the key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

Maintaining Your Airbag System

WARNING!

•

Modifications to any part of the airbag system
could cause it to fail when you need it. You could
be injured because the airbag is not there to protect
you. Do not modify the components or wiring,
including adding any kind of badges or stickers to
the airbag covers. Do not modify the front bumper
or vehicle body structure.

•

You need proper knee impact protection in a colli­sion. Do not mount or locate any aftermarket
equipment on or behind the knee impact bolsters.

•

You can be injured if you are too close to either
airbag cover when the airbags inflate. It is danger­ous to try to repair any part of the airbag system
yourself. Don’t try to repair the airbag system. Be
sure to tell anyone who works on your vehicle that
it has airbags.

You will want to have the airbags ready for your protec­tion in a collision. While the airbag Supplemental Re­straint System (SRS) is designed to be maintenance free,
if any of the following occurs, have an authorized dealer
service the system immediately.

•

The AIRBAG light does not come on or flickers during
the 6 to 8 seconds when the ignition switch is first
turned on.

•

The light remains on or flickers after the 6 to 8 second
interval.

•

The light flickers or comes on and remains on while
driving.

2

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Transporting Pets

Deploying airbags could harm your pet. An unrestrained
pet will be thrown about and possibly injured, or injure a
passenger during panic braking or in a collision.

Pets should be restrained in pet harnesses or pet carriers
that are secured by seat belts.

ENGINE BREAK-IN RECOMMENDATIONS

The engine in your new Viper does not require a long
break-in period. Following these few simple guidelines is
all that is necessary for a good break-in:

For the first 500 miles (800 km):

•

Keep your vehicle speed below the legal, posted speed
limit and your engine speed below 4,000 rpm.

•

Avoid driving at a constant speed, either fast or slow,
for long periods of time.

•

Do not make any full throttle starts and avoid full
throttle acceleration.

•

Use the proper gear for your speed range.

•

Wait until the engine has reached normal operating
temperature before driving at the recommended maxi­mum break-in speed.

•

Avoid excessive idling.

•

Check the engine oil level at every fuel fill.

NOTE: A new engine will consume some oil during the
first few thousand miles of operation. This should be
considered as a normal part of the break-in and not
interpreted as a sign of difficulty.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

SAFETY TIPS

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon
monoxide (CO) which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing (CO)
follow the safety tips below.

•

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in
or out of the area.

•

If it is necessary to sit in a parked vehicle with the
engine running, adjust your heating or cooling con­trols to force outside air into the vehicle. Set the blower
at high speed.

Safety Checks You Should Make Inside the
Vehicle

Seat Belts

Inspect the belt system periodically, checking for cuts,

•

frays and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the sys­tem.

•

Seat belt assemblies must be replaced after an accident
if they have been damaged (bent retractor, torn web­bing, etc.). If there is any question regarding belt or
retractor condition, replace the belt.

Defrosters

Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield.

2

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Safety Checks You Should Make Outside the
Vehicle

Tires

Examine tires for excessive tread wear or uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect for tread cuts or side wall
cracks. Check wheel nuts for tightness and tires for
proper pressure.

Lights

Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.

Fluid Leaks

Check area under vehicle after overnight parking for fuel,
water, oil, or other fluid leaks. Also, if gasoline fumes are
present, the cause should be corrected immediately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS

䡵 Convertible Top Operation .................55

▫ Electric Remote Control Mirrors ............68

3

▫ To Lower The Top ......................56

▫ To Raise The Top ......................56

▫ Convertible Top Boot Cover Installation–If

Equipped ............................59

▫ Convertible Top Boot Cover Removal And

Storage .............................64

䡵 Console Features ........................66

䡵 Mirrors ...............................67

▫ Inside Day/Night Mirror .................67

▫ Mirror Adjustment .....................68

䡵 Seats .................................69

▫ Manual Front Seat Adjustments ............69

▫ Reclining Seat .........................71

䡵 To Open And Close The Hood ..............71

䡵 Lights ................................73

▫ Courtesy/Reading Lights .................73

▫ Interior Lights ........................74

54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫ Multi-Function Control Lever ..............74

▫ Headlights, Parking Lights, Instrument Panel

Lights, And Front Fog Lights ..............75

▫ Daytime Running Lights .................76

▫ Lights-On Reminder ....................76

▫ Headlight Time Delay ...................76

▫ Battery Saver Feature — Exterior Lights ......76

▫ Fog Lights ...........................77

▫ Turn Signals ..........................77

▫ Highbeam/Lowbeam Select Switch ..........78

▫ Flash To Pass .........................78

䡵 Tilt Steering Column .....................78

䡵 Adjustable Pedals .......................79

▫ Adjustable Left Foot Rest .................80

䡵 Windshield Wipers And Washers .............81

▫ Windshield Washers ....................82

▫ Mist Function .........................82

▫ Intermittent Wiper System ................82

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55

CONVERTIBLE TOP OPERATION

WARNING!

The convertible top does not provide the structural
protection that a reinforced metal roof does, and the
fabric top cannot be expected to prevent the ejection
of the occupants of a vehicle in a collision. Therefore
it is important that all occupants wear their seat belts
at all times when riding in a convertible. Studies
have shown that it is generally safer to remain inside
a vehicle during a collision, than to be ejected from
the vehicle.

CAUTION!

To fully insure that no damage occurs, be sure that
the vehicle is at a complete stop with the gear
selector in the Park position (automatic transaxle) or
in the Neutral position (manual transaxle) before
lowering or raising the top.

CAUTION!

Do not operate the convertible top with ice or snow
build-up on the top. Damage to the top may occur.

3

56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Lower the Top:

Unlatching Convertible Top

1. To lower the top, first ensure that the door windows
are lowered at least an inch.

2. Depress the button at the top of the latch upwards and
then pull the handle down and rearward, towards you.
(See the picture shown)

3. Disengage the latch hook from the windshield rod
making sure to pull the latch all the way back to the
detent stow position and pull the top away from the
windshield header.

4. Open the trunk.

5. Pull the convertible top back away from the wind­shield and all the way back to the folded position into the
storage well to the back of the seating positions. Push the
leading edge of the top down to engage the downstack
latch.

6. Finally lower and close the trunk.

To Raise the Top:

1. To raise the convertible top, first ensure that the door
windows are lowered at least an inch.

2. Then open the trunk.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57

3. Release the lever located behind the driver’s seat and
nestled in the folded convertible top (as pictured). To aid
in disengaging the latch, press down on the convertible
top while pressing on the latch lever.

Convertible Top Latch

4. Manually raise the top until it meets the windshield
header (as pictured).

3

Raising Convertible Top

5. Close the trunk.

58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

6. While sitting inside the vehicle, hold onto the handles
and pull the top towards the windshield header. Push the
latch handle forward and engage the latch hook to the
windshield receiver rod.

Aligning Convertible Top

7. Ensure the outboard locating pins are in their respec­tive receiving holes in the windshield header. Push the
latch handle forward all the way to close the latch.

Engaging Convertible Top

NOTE: Until the convertible top system has had ad-

equate time to break in, it may take greater effort to

engage the latch hook and close the latch. Several weeks
of normal convertible top usage will reduce these efforts.

Convertible Top Boot Cover Installation–If
Equipped

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59

1. Open the trunk.

2. Lower the convertible top and make sure that the
convertible top latch handle is placed in the stowed
position.

3. lay the unfolded boot cover across the convertible top.

3

Unfolded Boot Cover

60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4. Slide pocket over the front corner of convertible top on
the passenger side.

Attaching Passenger Side

5. Stretch and slide pocket over the front corner of
convertible top on the driver side.

Attaching Driver Side

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61

6. Tuck cover under leading edge of convertible top. 7. Clip tab under trunk lid stop and quarter panel flange
on outer edge on the passenger side.

Tucking Boot Cover

Attaching Passenger Side Tab

3

62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

8. Push down to engage inboard tab on the passenger

side.

Engaging Passenger Side Tab Attaching Driver Side Tab

9. Clip tab under trunk lid stop and quarter panel flange
on outer edge on the driver side.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63

10. Push down to engage inboard tab on the driver side.

Push down on convertible top behind driver seat to lock
down.

Engaging Driver Side Tab

11. Stretch out and smooth cover from rear of vehicle.
Close the trunk lid.

3

Stretching and Smoothing Cover

64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

12. Ensure that the forward edge of the convertible top

boot is tucked in fully after the trunk is closed.

Forward Edge

Convertible Top Boot Cover Removal and
Storage

1. Open the trunk.

2. Pull up to disengage the inboard tab on the driver
side.

Disengaging Driver Side Tab

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65

3. Pull up to disengage the inboard tab on the passenger

side.

Disengaging Passenger Side Tab

4. Fold each of the outer edges of the convertible top
cover inward.

3

Folding Outer Edges

66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. Fold the convertible top cover again. Place the cover

into the bag. Store the cover in the trunk or a dry secure
area.

Folding Boot Cover

CONSOLE FEATURES

The front console has a removable ashtray, power outlet/
cigarette lighter and power window switches.

The center console compartment is equipped with a
cigarette lighter/power outlet and a passenger airbag
on/off switch.

Console

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67

MIRRORS

Inside Day/Night Mirror

Adjust the mirror to center on the view through the rear
window. A pivot system allows for horizontal and verti­cal mirror adjustment.

Adjusting Rearview Mirror

Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward rear of vehicle). The mirror should be adjusted
while set in the day position (toward windshield).

3

68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Electric Remote Control Mirrors

Both of the outside mirrors can be adjusted by using the
remote controls mounted inside the driver’s door, below
the door handle and power door switch.

Power Mirror Controls

NOTE: Place the mirror selector switch in the center

(neutral) position to prevent accidental movement of the
mirrors.

Mirror Adjustment

Outside Mirror — Driver’s Side

Adjust the outside mirror to center on the adjacent lane of
traffic, with a slight overlap of the view obtained on the
inside mirror.

Right Side Mirror

Adjust the convex outside mirror so you can just see the
side of your vehicle. This type of mirror will give a much
wider view to the rear, and especially of the lane next to
your vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69

WARNING!

Vehicles and other objects seen in the right side
convex mirror will look smaller and farther away
than they really are. Relying too much on your right
side mirror could cause you to collide with another
vehicle or other object. Use your inside mirror when
judging the size or distance of a vehicle seen in this
convex mirror.

SEATS

Manual Front Seat Adjustments

The adjusting bar is at the front of the seats, near the
floor. Pull the bar up to move the seat to the desired
position.

Using body pressure, move forward and rearward on the
seat to be sure the seat adjusters have latched.

3

70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Adjusting a seat while the vehicle is moving is
dangerous. If you are driving, the sudden movement
of the seat could cause you to lose control. You could
be injured. Adjust any seat only while the vehicle is
parked. Do not ride with the seatback reclined so
that the shoulder belt is no longer riding against
your chest. In a collision you could slide under the
seat belt and be seriously or even fatally injured. Use
the recliner only when the vehicle is parked.

Manual Seat Controls

Reclining Seat

The recliner control is on the side of the seat on the
door-side. To recline, lean forward slightly before pulling
the lever, then lean back to the desired position, and
release the lever. Lean forward and pull the lever to
return the seatback to its original position.

To Open And Close The Hood

Two latches must be released to open the hood. First,
reach into the lower right grille opening and pull the
primary hood latch forward. Raise the front of the hood
slightly for access to the safety catch.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71

3

Hood Release Lever

72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Then push the safety catch handle located under the front
edge of the hood toward the right. Raise the front of the
hood.

Hood Safety Catch

NOTE: Assist props will raise the hood to a normal

customer usage position. If greater access is required, the
hood may be pushed up at the front, raising the hood
beyond the initial opening height. Simply pull the hood
down to close it.

CAUTION!

Do not leave the hood open in areas where strong
gusts of wind are likely. Such a place might be by the
side of the road where large trucks pass by. Strong
gusts of wind may damage your hood. Always close
the hood in such situations.

WARNING!

If the hood is not fully latched, it could open when
the vehicle is moving and block your forward vision.
Be sure the hood latches are fully latched before
driving.

LIGHTS

Courtesy/Reading Lights

These lights, located under the rearview mirror, come on
whenever a door is opened or the illuminated entry
system is activated. The lights can also be turned on with
the doors closed by means of switches located on the
bottom of the rearview mirror. These lights also function
by rotating the dimmer control in the multi-function
control lever.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73

3

Courtesy/Reading Light Switches

There are also courtesy lights located in both the driver
and passenger footwell areas. They will turn on as part of
the illuminated entry system by either opening a door,
unlocking the door from the remote keyless entry, or by
the multi-function control lever dimmer control.

74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Interior Lights

The interior lights come on when a door is opened and
the dome switch is not in the defeat position.

Battery Saver Feature — Interior Lights

The interior courtesy lights come on when a door is open
or left ajar. To prevent battery drain, if you leave a door
open or ajar, these lights will turn off after 15 minutes.
After you close the door, the interior courtesy lights will
again function in the normal manner.

Multi-Function Control Lever

The Multi-Function Control Lever controls the operation
of the headlights, parking lights, turn signals, headlight
beam selection, instrument panel light dimming, interior
lights, the passing lights, and fog lights. The lever is
located on the left side of the steering column.

Dimmer Control

With the parking lights or headlights
on, rotating the dimmer control for the
interior lights on the Multi-Function
Control Lever upward will increase
the brightness of the instrument panel
lights.

Dome Light Position

Rotate the dimmer control completely
upward to the second detent to turn
on the interior lights. The interior
lights will remain on when the dim­mer control is in this position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75

Interior Light Defeat (OFF)

Rotate the dimmer control to the ex­treme bottom “OFF” position. The in­terior lights will remain off when the
doors are open.

Parade Mode (Daytime Brightness Feature)

Rotate the dimmer control to the first
detent (white semi-circle). This feature
brightens the odometer and radio dis­play when the parking lights or head­lights are on during daylight condi­tions.

Headlights, Parking Lights, Instrument Panel
Lights, and Front Fog Lights

Turn the end of the Multi-Function Control Lever to the
first detent for parking light operation. Turn to the
second detent for headlight operation. Pull out the end of
the Multi-Function Control Lever to turn on the front fog
lights.

Multi-Function Lever

3

76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To change the brightness of the instrument panel lights,
rotate the center portion of the Multi-Function Control
Lever up or down.

Daytime Running Lights

The fog lights will come on as Daytime Running Lights
whenever the ignition switch is on, the headlights are off,
and the parking brake is off. The headlight switch must
be used for normal night time driving.

NOTE: This feature is standard on all Canadian vehicles
and cannot be disabled. For US vehicles, this feature is
shipped disabled and can be enabled (or disabled) at a
dealership if so desired.

Lights-On Reminder

If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound to alert the driver
when the driver’s door is opened.

Headlight Time Delay

This feature provides the safety of headlight illumination
for about 90 seconds.

To activate the delay, turn off the ignition while the
headlights are still on. Then turn off the headlights within
45 seconds. The delay interval begins when the headlamp
switch is turned off.

If the headlights are turned off before the ignition, they
will go off in the normal manner.

This feature can be disabled at the dealership if so
desired.

Battery Saver Feature — Exterior Lights

If an exterior light is left on when the ignition switch is
moved to the Off position (with the key in or out), it will
automatically turn off after 3 minutes. Normal operation
will resume when the ignition is turned On or when the
headlight switch is turned to another position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77

If the ignition switch is turned to any position other than
the Off position at any time during the 3 minute delay
period the battery saver feature will be disabled.

Fog Lights

The front fog light switch is on the Multi-Function
Control Lever. To activate the front fog lights, turn
on the parking lights or the low beam headlights

and pull out the end of the control lever.

NOTE: The fog lights will only operate with the head­lights on low beam. Selecting high beam headlights will
turn off the fog lights.

Turn Signals

3

Turn Signal Lever

Move the Multi-Function Control Lever up or down and
the arrows on each side of the instrument cluster flash to
show proper operation of the front and rear turn signal
lights. You can signal a lane change by moving the lever
partially up or down without moving beyond the detent.

78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If either light remains on and does not flash, or there is a
very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is
moved, it would suggest that the fuse or indicator bulb is
defective.

Highbeam/Lowbeam Select Switch

Pull the Multi-Function Control Lever towards you to
switch the headlights to HIGH beam. Pull the control
lever a second time to switch the headlights to LOW
beam.

Flash to Pass

You can signal another vehicle with your headlights by
lightly pulling the multi-function lever toward the steer­ing wheel. This will cause the headlights to turn on at
high beam and remain on until the lever is released.

Tilt Steering Column

To tilt the column, simply pull down the small lever
below the turn signal control and move the wheel up or
down, as desired. Return the lever to the up position to
lock the wheel firmly in place.

Tilt Steering Column Control

WARNING!

Tilting the steering column while the vehicle is
moving is dangerous. Without a stable steering col­umn, you could lose control of the vehicle and have
an accident. Adjust the column only while the ve­hicle is stopped. Be sure it is locked before driving.

ADJUSTABLE PEDALS

Your Viper is equipped with an adjustable pedal system
that allows about 4 inches (100 mm) of fore and aft pedal
adjustment. The pedals are adjusted using a switch
recessed into the knee bolster beneath the steering col­umn.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79

3

Adjustable Pedal Switch

80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To adjust the pedals:

•

Adjust the seat to a comfortable driving position.

•

Adjust the pedals to a position that allows full pedal
travel.

•

It may be necessary to make further small adjustments
to find the best possible seat/pedal position.

WARNING!

Do not adjust the pedals while the vehicle is moving.
You could lose control and have an accident. Always
adjust the pedals while the vehicle is parked.

Adjustable Left Foot Rest

Adjustable Foot Rest

The left foot rest can be manually adjusted fore and aft
and rotated up and down to a comfortable position.

To adjust the left foot rest:

•

Loosen the nut on the pedal using a 13 mm socket.

•

Slide the pedal fore, aft and/or rotate up or down to
find a comfortable position.

•

Retighten the nut, being careful not to overtighten.

WINDSHIELD WIPERS AND WASHERS

The wipers and washers are operated by a switch
in the right control lever. Move the control lever
up to select the desired wiper speed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81

3

Windshield Wiper/Washer Control

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Windshield Washers

To use the washer, pull the control lever toward you and
hold while spray is desired. If the lever is pulled while in
the delay range, the wiper will operate in low speed for
two wipe cycles after the lever is released, and then
resume the intermittent interval previously selected.

If the lever is pulled while in the OFF position, the wipers
will operate for two wipe cycles, then turn OFF.

Mist Function

Push down on the wiper control lever to activate a single
wipe to clear the windshield of road mist or spray from
a passing vehicle. The wiper blade will continue to wipe
until you release the stalk.

Intermittent Wiper System

Use the intermittent wiper when weather conditions
make a single wiping cycle with a variable pause be­tween cycles desirable. Move the lever to the first detent
(DEL) position, then select the delay interval by turning
the end of the stalk. Rotate the end upward to decrease
the delay time and downward to increase it. The delay
can be regulated from one second between cycles to 15
seconds between cycles.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel Features ..................85

䡵 Instrument Cluster Description ..............86

▫ Speedometer ..........................86

▫ Turn Signal Indicators ...................87

▫ Hazard Indicator .......................87

▫ Message Center .......................87

▫ Gauges .............................92

䡵 Electronic Digital Clock ...................93

▫ Clock Setting Procedure..................93

䡵 Radio General Information .................94

▫ Radio Broadcast Signals ..................94

▫ Two Types Of Signals ...................94

▫ Electrical Disturbances ...................94

▫ AM Reception ........................94

▫ FM Reception .........................95

䡵 Sales Code RBQ—AM/FM Stereo Radio With 6 -

Disc CD Changer ........................95

▫ Radio Operation .......................96

4

84 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ CD Player Operation ....................98

䡵 CD/DVD Disc Maintenance ...............103

䡵 Radio Antenna ........................103

䡵 Radio Operation And Cellular Phones ........103

䡵 Ventilation ............................104

䡵 Climate Controls .......................104

▫ Fan Control .........................105

▫ Temperature Control ...................105

▫ Mode Control ........................105

▫ Operating Tips .......................107

INSTRUMENT PANEL FEATURES

UNDERSTANDING YOUR INSTRUMENT PANEL 85

4

86 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTION

Speedometer

Shows the vehicle speed in miles-per­hour and kilometers-per-hour.

Odometer/Trip Odometer

The odometer shows the total distance the vehicle has
been driven.

U.S. federal regulations require that upon transfer of
vehicle ownership, the seller certify to the purchaser the
correct mileage that the vehicle has been driven. There­fore, if the odometer reading is changed, during repair or

replacement, be sure to keep a record of the reading
before and after the service so that the correct mileage can
be determined.

The trip odometer shows individual trip mileage. To
switch from odometer to trip odometer, press and release
the Trip Odometer button. Press and release the Trip
button a second time to return to the odometer. While in
trip mode, press and hold the button for at least 1 second
to reset the trip odometer to zero.

Door Unlocked, Door Ajar, Low Tire Warnings

If you move the vehicle and a door is not completely
closed, the words DOOR AJAR will appear in the display
and a chime will sound once. If the door is not locked,
DOOR UNLOCK will appear in the display. If the tire
pressure is low, the words LOW TIRE will appear in the
display and a chime will sound once.

UNDERSTANDING YOUR INSTRUMENT PANEL 87

Turn Signal Indicators

The arrows will flash in unison with the corresponding
exterior turn signal when using the signal lever.

Hazard Indicator

Both turn signal arrows will flash in unison with all front
and rear turn signals when the hazard warning switch is
used.

NOTE: Leaving the hazard flashers on for extended
periods of time will wear down the battery.

Message Center

Message Center Components

Anti-Lock Warning Light

The amber ABS Warning Light will come on
when the ignition is first turned on, and stay on
briefly as a bulb check. If the bulb does not

come on during starting, have the bulb re­paired promptly. This light also illuminates to indicate
that the Antilock Brake System self-check is in process at
vehicle start-up. If the light remains on after start-up, or
comes on and stays on at road speeds, it may indicate
that the ABS has detected a malfunction or has become
inoperative. In this case, the system reverts to standard
non-antilock brakes. Turn the engine off and on again to
reset the Antilock Brake System. If the light remains on,
see your authorized dealer. If both the red BRAKE and
amber ABS warning lights are on and the parking brake
is fully released, see your authorized dealer immediately.

4

88 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!

If both ABS and/or Brake Warning lamps become
illuminated, please seek service immediately! Your
Viper will have diminished braking capability and
control if ABS and/or service brake systems are not
working properly. Have your brake system serviced
immediately.

Skip Shift Indicator

This indicator is located in the Tachometer. There

are two LED lights. The amber LED light will come
on when you are being prevented from shifting from First
to Second or Third gear. The tachometer’s shift arrow also
houses a red LED light that activates when the tachom­eter gauge pointer goes above 5600 RPM and it shuts off
when the tachometer pointer falls below 5500 RPM. The
indicator serves as a visual aid to shift before reaching the
red line.

Malfunction Indicator Light

This light is part of an onboard diagnostic
system called OBD II which provides in-field
emissions inspection tests required in some

states. If certain self-diagnostic monitors are
not complete, the light starts flashing 14 seconds after the
key is switched on and will continue to flash for approxi­mately 11 seconds. If the OBD II monitors have com­pleted, the malfunction indicator lamp will not flash as
described above.

The light will illuminate when the key is turned to the
ON position before engine start. The light will remain on
steady until the engine has started. If the bulb does not
come on when turning the key from OFF to ON have the
condition checked promptly. The light will turn off after
the engine has started, unless a malfunction is present.

UNDERSTANDING YOUR INSTRUMENT PANEL 89

CAUTION!

Prolonged driving with the light on could cause
further damage to the emission control system. It
could also affect fuel economy and driveability. The
vehicle must be serviced before any state emissions
tests can be performed.

If the light is flashing, severe catalytic converter damage
and power loss will soon occur. Immediate service is
required.

If the gas cap is not secured properly, the light may come
on. Be sure the gas cap is tightened every time you add
fuel.

High Beam Indicator

This light shows that the headlights are on high

beam. Pull the turn signal lever toward the steer­ing wheel to switch the headlights from high or low
beam.

Seat Belt Indicator Light

This system alerts the driver to fasten the seat belt

if not done so within 60 seconds of starting the

vehicle and if the vehicle is moving faster than 5
mph (8 km/h). The system will cause a chime to sound
repeatedly and will flash the seat belt warning light for 96
seconds or until the driver’s seat belt is fastened. The
reminder system will be reactivated if the driver’s seat
belt is unfastened for more than 10 seconds and the
vehicle speed is greater than 5 mph (8 km/hr). Refer to
Enhanced Seat Belt Use Reminder System (BeltAlert™)in
the Occupant Restraints section for deactivating the
system.

4

90 UNDERSTANDING YOUR INSTRUMENT PANEL

Trunk Ajar Light

This light indicates that the trunk is not latched.

Engine Coolant Temperature Light

A red LED light on the Coolant Temperature
gauge will illuminate to warn of an overheated
engine coolant condition.

Low Oil Pressure Light

A red LED light on the Oil Pressure gauge will

illuminate to indicate low engine oil pressure. The
light should come on briefly as a bulb check when the
engine is first started. If the light stays on or comes on
while driving, stop the vehicle and shut off the engine.
DO NOT operate the vehicle until the cause is corrected.

NOTE: This light does not indicate how much oil is in
the engine. The engine oil level must be checked under
the hood.

Charge System Light

A red LED light on the Voltage gauge will illumi­nate when there is a charging system malfunction

or a possible accessory drive belt failure.

CAUTION!

The accessory belt also drives the water pump.
Operating the vehicle with a failed belt can cause
engine overheating and possible severe engine dam­age.

Fog Light ON Indicator

This light indicates that the fog lights are on.

UNDERSTANDING YOUR INSTRUMENT PANEL 91

Brake System Warning Light

The dual brake system provides a reserve
braking capability in the event of a failure to a
portion of the hydraulic system. The warning

light should be checked frequently to assure
that it is operating properly. This can be done by turning
the ignition switch to a point midway between ON and
START. The light should come on. The red Brake Warning
Light will come on when the ignition is first turned on,
and stay on briefly as a bulb check. If the bulb does not
come on during starting, have the bulb repaired
promptly. If the light stays on longer, it may be an
indication that the parking brake has not been released. If
the light remains on when the parking brake is off it
indicates a possible brake hydraulic system malfunction.
Immediate repair is necessary and continued operation of
the vehicle in this condition is dangerous.

WARNING!

Driving a vehicle with the brake light on is danger­ous. Part of the brake system has failed. It will take
longer to stop the vehicle. You could have a accident.
Have the brakes checked immediately.

Airbag Light

This light will come on and remain on for 6 to
8 seconds as a bulb check when the ignition
switch is first turned on. If the bulb is not lit

during starting, have it replaced. If the light
stays on or comes on while driving, have the system
checked by an authorized dealer.

4

92 UNDERSTANDING YOUR INSTRUMENT PANEL

Gauges

Tachometer

This gauge shows engine speed in revolutions­per-minute (RPM) times 1,000. Avoid excessive
engine speeds in any part of the red warning
zone, particularly when driving downhill or in

lower gears.

Coolant Temperature Gauge

This gauge shows the engine coolant tempera­ture. The gauge pointer will likely show higher
temperatures when driving in hot weather, up

mountain grades, or in heavy stop and go
traffic. If the red LED light turns on, stop the vehicle and
turn off the engine until the cause is corrected.

Oil Temperature Gauge

This gauge shows the oil temperature. The
gauge pointer will likely show higher tempera­tures when driving in hot weather, up moun-

tain grades, or in heavy stop and go traffic. If
the red LED light turns on, stop the vehicle and turn off
the engine until the cause is corrected.

Oil Pressure Gauge

This gauge shows engine oil pressure when the

engine is running. The pressure will vary with

engine speed, oil viscosity, and engine tem-

perature. Oil pressures will be higher as the
engine is warming up. The normal operating pressure is
between 20 and 80 psi (pounds per square inch). If the
pointer remains in the red range, turn off the engine until
the cause is corrected.

UNDERSTANDING YOUR INSTRUMENT PANEL 93

This gauge does not indicate the amount of oil in the
engine. The engine oil level must be checked under the
hood. Check the level often during severe usage.

Fuel Gauge

This gauge shows the amount of fuel in the gas
tank. The reaction time of the gauge has been
slowed to avoid needle fluctuation during pe­riods of high G force cornering.

Voltage Gauge

This gauge shows the electrical system voltage.
The normal operating voltage is from 12 to 14
volts with the engine running. If the pointer
remains at either the high or low ends of the

scale, the electrical system should be serviced.

ELECTRONIC DIGITAL CLOCK

The clock and radio each use the display panel built into
the radio. A digital readout shows the time in hours and
minutes whenever the ignition switch is in the ON or
ACC position.

When the ignition switch is in the OFF position, or when
the radio frequency is being displayed, time keeping is
accurately maintained.

Press and release the Time button to display the time.
Press and release the button a second time to turn off the
time display.

Clock Setting Procedure

1. Turn the ignition switch to the “ON” or “ACC”
position. Using the point of a ballpoint pen or similar
object, press either the “H” (Hour) or “M” (Minute)
buttons on the radio. The display will show the time.

4

94 UNDERSTANDING YOUR INSTRUMENT PANEL

2. Press the “H” button to set hours or the “M” button to
set minutes. The time setting will increase each time you
press a button.

RADIO GENERAL INFORMATION

Radio Broadcast Signals

Your new radio will provide excellent reception under
most operating conditions. Like any system, however, car
radios have performance limitations, due to mobile op­eration and natural phenomena, which might lead you to
believe your sound system is malfunctioning. To help
you understand and save you concern about these “ap­parent” malfunctions, you must understand a point or
two about the transmission and reception of radio sig­nals.

Two Types of Signals

There are two basic types of radio signals... AM or
Amplitude Modulation, in which the transmitted sound
causes the amplitude, or height, of the radio waves to
vary... and FM or Frequency Modulation, in which the
frequency of the wave is varied to carry the sound.

Electrical Disturbances

Radio waves may pick up electrical disturbances during
transmission. They mainly affect the wave amplitude,
and thus remain a part of the AM reception. They
interfere very little with the frequency variations that
carry the FM signal.

AM Reception

AM sound is based on wave amplitude, so AM reception
can be disrupted by such things as lightning, power lines
and neon signs.

UNDERSTANDING YOUR INSTRUMENT PANEL 95

FM Reception

Because FM transmission is based on frequency varia­tions, interference that consists of amplitude variations
can be filtered out, leaving the reception relatively clear,
which is the major feature of FM radio.

NOTE: On vehicles so equipped the radio, steering
wheel radio controls and 6 disc CD/DVD changer will
remain active for up to 45 seconds after the ignition
switch has been turned off. Opening a vehicle front door
will cancel this feature.

SALES CODE RBQ—AM/FM STEREO RADIO
WITH 6 - DISC CD CHANGER

4

RBQ Radio

96 UNDERSTANDING YOUR INSTRUMENT PANEL

Radio Operation

Power/Volume Control

Press the PWR/VOL control to turn the radio on. Turn
the volume control clockwise to increase the volume.

NOTE: Power to operate the radio is controlled by the
ignition switch. It must be in the ON or ACC position to
operate the radio.

Mode

Press the MODE button repeatedly to select between AM,
FM, the CD changer and Sirius Satellite Radio™ (if
equipped). The display will show ST when a stereo
station is received.

To select Sirius Satellite Radio™ (if equipped), press the
MODE button until the word SIRIUS appears. The fol­lowing will be displayed in this order: After three sec­onds, the current channel name and number will be
displayed for five seconds. The current program type and

channel number will then be displayed for five seconds.
The current channel name and number will then be
displayed until an action occurs. CD’s may remain in the
player while in the Satellite Radio mode.

Seek

Press and release the SEEK button to search for the next
station in either the AM or FM mode. Press the top of the
button to seek up and the bottom to seek down. The
radio will remain tuned to the new station until you
make another selection. Holding the button in will by­pass stations without stopping until you release it.

Tune

Press the TUNE control up or down to increase or
decrease the frequency. If the button is pressed and held,
the radio will continue to tune until the button is
released. The frequency will be displayed and continu­ously updated while the button is pressed.

UNDERSTANDING YOUR INSTRUMENT PANEL 97

To Set The Radio Push-Button Memory

When you are receiving a station that you wish to
commit to push-button memory, press the SET RND
button. SET 1 will show in the display window. Select the
“1–6” button you wish to lock onto this station and press
and release that button. If a button is not selected within
5 seconds after pressing the SET RND button, the station
will continue to play but will not be locked into push­button memory.

You may add a second station to each push-button by
repeating the above procedure with this exception: Press
the SET button twice and SET 2 will show in the display
window. Each button can be set for SET 1 and SET 2 in
both AM and FM. This allows a total of 12 AM and 12 FM
stations to be locked into push-button memory. The
stations stored in SET 2 memory can be selected by
pressing the corresponding push-button twice. Every
time a preset button is used, a corresponding button
number will be displayed.

Audio

The audio button controls the BASS, TREBLE, BAL­ANCE, and FADE.

Press the AUDIO button and BASS will be displayed.
Press the SEEK + or SEEK – to increase or decrease the
Bass tones.

Press the AUDIO button a second time and TREB will be
displayed. Press the SEEK + or SEEK – to increase or
decrease the Treble tones.

Press the AUDIO button a third time and BAL will be
displayed. Press the SEEK + or SEEK – to adjust the
sound level from the right or left side speakers.

Press the AUDIO button a fourth time and FADE will be
displayed. Press the SEEK + or SEEK – to adjust the
sound level between the front and rear speakers.

Press the AUDIO button again or wait 5 seconds to exit
setting tone, balance, and fade.

4

98 UNDERSTANDING YOUR INSTRUMENT PANEL

Time Button

Press the TIME button to change the display between
radio frequency and time.

General Information

This radio complies with Part 15 of FCC rules and with
RSS-210 of Industry Canada. Operation is subject to the
following conditions:

1. This device may not cause harmful interference,

2. This device must accept any interference received,
including interference that may cause undesired opera­tion.

NOTE: Changes or modifications not expressively ap­proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

CD Player Operation

NOTE: The ignition switch must be in the ON or ACC
position and the Power / Volume control pushed ON
before the CD player will operate.

Inserting The Compact Disc

CAUTION!

This CD player will accept 43⁄4inch (12 cm) discs
only. The use of other sized discs may damage the
CD player mechanism.

You may either insert or eject a disc with the radio OFF.

If you insert a disc with the ignition ON and the radio
OFF, the display will show the time of day. If you insert
a disc with the ignition OFF, the display will show the
time of day for about 5 seconds, then go out.

UNDERSTANDING YOUR INSTRUMENT PANEL 99

If you insert a disc with the ignition ON and the radio
ON, the unit will switch from radio to CD mode and
begin to play when you insert the disc. The display will
show the disc number, the track number, and index time
in minutes and seconds. Play will begin at the start of
track 1.

LOAD/ EJT — Load

Press the LOAD/ EJT button and the button with the
corresponding number where the CD is being loaded.
After the radio displays “load” insert the CD into the
player.

Radio display will show “loading” when it is being
loaded.

LOAD / EJT — Eject

Press the LOAD/ EJT button and the button with the
corresponding number where the CD was loaded and the
disc will unload and move to the entrance for easy
removal.

Radio display will show “ejecting” when it is being
ejected.

If you have ejected a disc and have not removed it within
15 seconds, it will be reloaded. If the CD is not removed,
the radio will continue to play the non-removed CD. If
the CD is removed and there are other CD’s in the radio,
the radio will play the next CD. If the CD is removed and
there are no other CD’s in the radio, the radio will return
to the last selected AM or FM mode.

The disc can be ejected with the radio and ignition OFF.

Seek

Press the top of the SEEK button for the next selection on
the CD. Press the bottom of the button to return to the
beginning of the current selection, or return to the
beginning of the previous selection if the CD is within the
first second of the current selection.

4

100 UNDERSTANDING YOUR INSTRUMENT PANEL

Scan

Press the Scan button to scan through each track on the
CD currently playing.

FF/TUNE/RW

Press FF (Fast Forward) and the CD player will begin to
fast forward until FF is released. The RW ( Reverse)
button works in a similar manner.

Random Play — SET / RND

Press the RND button while the CD is playing to activate
Random Play. This feature plays the tracks on the disc in
random order to provide an interesting change of pace.

Press the SEEK button to move to the next randomly
selected track.

Press the SET / RND button a second time to stop
Random Play.

PTY (Program Type) Button

Pressing this button once will turn on the PTY mode for
5 seconds. If no action is taken during the 5 second time
out the PTY icon will turn off. Pressing the PTY button
repeatedly within 5 seconds will allow the program
format type to be selected. Many radio stations do not
currently broadcast PTY information.

Toggle the PTY button to select the following format
types:

Program Type Radio Display

Adult Hits Adlt Hit
Classical Classicl
Classic Rock Cls Rock
College College
Country Country
Emergency ALERT!
Emergency Test Test