DiamlerChrysler wiring diagrams are designed to
provide information regarding the vehicles wiring
content. In order to effectively use DiamlerChrysler
wiringdiagramstodiagnoseandrepaira
DiamlerChrysler vehicle, it is important to underÂstand all of their features and characteristics.
Diagrams are arranged such that the power (B+)
side of the circuit is placed near the top of the page,
and the ground (B-) side of the circuit is placed near
the bottom of the page.
All switches, components, and modules are shown
in the at rest position with the doors closed and the
key removed from the ignition.
TROUBLESHOOTING WIRING PROBLEMS.....10
SERVICE PROCEDURES
CONNECTOR AND TERMINAL
REPLACEMENT ........................13
CONNECTOR REPLACEMENT ..............12
DIODE REPLACEMENT ....................15
TERMINAL REPLACEMENT.................14
TERMINAL/CONNECTOR REPAIR- AUGAT
CONNECTORS .........................12
TERMINAL/CONNECTOR REPAIR-MOLEX
CONNECTORS .........................11
TERMINAL/CONNECTOR REPAIR—THOMAS
AND BETTS CONNECTORS ...............11
WIRING REPAIR .........................10
SPECIAL TOOLS
WIRING/TERMINAL .......................16
Components are shown two ways. A solid line
around a component indicates that the component is
complete. A dashed line around a component indiÂcates that the component being shown is not comÂplete. Incomplete components have a reference
number to indicate the page where the component is
shown complete.
It is important to realize that no attempt is made
on the diagrams to represent components and wiring
as they appear on the vehicle. For example, a short
piece of wire is treated the same as a long one. In
addition, switches and other components are shown
as simply as possible, with regard to function only.
Page 4
8W - 01 - 28W - 01 GENERAL INFORMATIONPL
DESCRIPTION AND OPERATION (Continued)
The System shown here is an EXAMPLE ONLY. It does not represent the actual circuit shown in the WIRING
DIAGRAM SECTION.
Page 5
PL8W - 01 GENERAL INFORMATION8W - 01 - 3
DESCRIPTION AND OPERATION (Continued)
The System shown here is an EXAMPLE ONLY. It does not represent the actual circuit shown in the WIRING
DIAGRAM SECTION.
Page 6
8W - 01 - 48W - 01 GENERAL INFORMATIONPL
DESCRIPTION AND OPERATION (Continued)
CIRCUIT INFORMATION
Each wire shown in the diagrams contains a code
which identifies the main circuit, part of the main
circuit, gage of wire, and color (Fig. 1).
Fig. 1 Wire Code Identification
1 – COLOR OF WIRE (LIGHT BLUE WITH YELLOW TRACER)
2 – GAUGE OF WIRE (18 GAUGE)
3 – PART OF MAIN CIRCUIT (VARIES DEPENDING ON
All circuits in the diagrams use an alpha/numeric
code to identify the wire and its function. To identify
which circuit code applies to a system, refer to the
Circuit Identification Code Chart. This chart shows
the main circuits only and does not show the secondÂary codes that may apply to some models.
LEXTERIOR LIGHTING
MINTERIOR LIGHTING
NNOT USED
ONOT USED
PPOWER OPTION (BATTERY FEED)
QPOWER OPTIONS (IGNITION FEED)
RPASSIVE RESTRAINT
SSUSPENSION/STEERING
TTRANSMISSION/TRANSAXLE/
TRANSFER CASE
UOPEN
VSPEED CONTROL, WIPER/WASHER
WOPEN
XAUDIO SYSTEMS
YOPEN
ZGROUNDS
Page 7
PL8W - 01 GENERAL INFORMATION8W - 01 - 5
DESCRIPTION AND OPERATION (Continued)
SECTION IDENTIFICATION
The wiring diagrams are grouped into individual
sections. If a component is most likely found in a parÂticular group, it will be shown complete (all wires,
connectors, and pins) within that group. For examÂple, the Auto Shutdown Relay is most likely to be
found in Group 30, so it is shown there complete. It
can, however, be shown partially in another group if
it contains some associated wiring.
SYMBOLS
International symbols are used throughout the wirÂing diagrams. These symbols are consistent with
those being used around the world.
GROUPTOPIC
8W-01 thru
8W-09
8W-10 thru
8W-19
8W-20 thru
8W-29
8W-30 thru
8W-39
8W-40 thru
8W-49
8W-50 thru
8W-59
8W-60 thru
8W-69
8W-70Splice Information
8W-80Connector Pin Outs
8W-90Connector Locations (including
8W-95Splice Locations
General Information and Diagram
Overview
Main Sources of Power and Vehicle
Grounding
Starting and Charging
Powertrain/Drivetrain Systems
Body Electrical items and A/C
Exterior Lighting, Wipers, and Trailer
Tow
Power Accessories
grounds)
Page 8
8W - 01 - 68W - 01 GENERAL INFORMATIONPL
DESCRIPTION AND OPERATION (Continued)
Wiring Diagram Symbols
Page 9
PL8W - 01 GENERAL INFORMATION8W - 01 - 7
DESCRIPTION AND OPERATION (Continued)
TERMINOLOGY
This a list of terms with there definitions used in
the wiring diagrams.
Built-Up-Export ....... Vehicles Built For Sale In
Markets Other Than North America
Except-Built-Up-Export . Vehicles Built For Sale In
North America
LHD ................ Left Hand Drive Vehicles
RHD ............... Right Hand Drive Vehicles
ATX . . Automatic Transmission-Front Wheel Drive
MTX.... Manual Transmission-Front Wheel Drive
AT .... Automatic Transmission-Rear Wheel Drive
MT...... Manual Transmission-Rear Wheel Drive
SOHC ........... Single Over Head Cam Engine
DOHC ............ Dual Over Head Cam Engine
CONNECTOR INFORMATION
CAUTION: Not all connectors are serviced. Some
connectors are serviced only with a harness. A typÂical example might be the Supplemental Restraint
System connectors. Always check parts availability
before attempting a repair.
SPLICE LOCATIONS
Splice Location charts in Section 8W-70 show the
entire splice, and provide references to other sections
the splice serves.
Section 8W-95 contains illustrations that show the
general location of the splices in each harness. The
illustrations show the splice by number, and provide
a written location.
NOTES, CAUTIONS, and WARNINGS
Throughout this group additional important inforÂmation is presented in three ways; Notes, Cautions,
and Warnings.
NOTES are used to help describe how switches or
components operate to complete a particular circuit.
They are also used to indicate different conditions
that may appear on the vehicle. For example, an
up-to and after condition.
CAUTIONS are used to indicate information that
could prevent making an error that may damage the
vehicle.
WARNINGS provide information to prevent perÂsonal injury and vehicle damage. Below is a list of
general warnings that should be followed any time a
vehicle is being serviced.
IDENTIFICATION
In-line connectors are identified by a number, as
follows:
• In-line connectors located on the engine com-
partment harness are C100 series numbers.
• Connectors located on the instrument panel
harness are C200 series numbers.
• Connectors located on the body harness are
C300 series numbers.
• Jumper harness connectors are C400 series
numbers.
• Grounds and ground connectors are identi-
fied with a “G” and follow the same series numberÂing as the in-line connector.
Component connectors are identified by the compoÂnent name instead of a number. Multiple connectors
on a component use a C1, C2, etc. identifier.
LOCATIONS
Section 8W-90 contains connector/ground location
illustrations. The illustrations contain the connector
name (or number)/ground number and component
identification. Connector/ground location charts in
Section 8W-90 reference the illustration number for
components and connectors.
Section 8W-80 shows each connector and the cirÂcuits involved with that connector. The connectors
are identified using the name/number on the DiaÂgram pages.
WARNING: ALWAYS WEAR SAFETY GLASSES FOR
EYE PROTECTION.
WARNING: USE SAFETY STANDS ANYTIME A PROÂCEDURE REQUIRES BEING UNDER A VEHICLE.
WARNING: BE SURE THAT THE IGNITION SWITCH
ALWAYS IS IN THE OFF POSITION, UNLESS THE
PROCEDURE REQUIRES IT TO BE ON.
WARNING: SETTHEPARKINGBRAKEWHEN
WORKING ON ANY VEHICLE. AN AUTOMATIC
TRANSMISSION SHOULD BE IN PARK. A MANUAL
TRANSMISSION SHOULD BE IN NEUTRAL.
WARNING: OPERATE THE ENGINE ONLY IN A
WELL-VENTILATED AREA.
WARNING: KEEP AWAY FROM MOVING PARTS
WHEN THE ENGINE IS RUNNING, ESPECIALLY THE
FAN AND BELTS.
WARNING: TO PREVENT SERIOUS BURNS, AVOID
CONTACT WITH HOT PARTS SUCH AS THE RADIAÂTOR, EXHAUST MANIFOLD(S), TAIL PIPE, CATAÂLYTIC CONVERTER, AND MUFFLER.
Page 10
8W - 01 - 88W - 01 GENERAL INFORMATIONPL
DESCRIPTION AND OPERATION (Continued)
WARNING: DO NOT ALLOW FLAME OR SPARKS
NEARTHEBATTERY.GASESAREALWAYS
PRESENT IN AND AROUND THE BATTERY.
The abbreviation T/O is used in the component
location section to indicate a point in which the wirÂing harness branches out to a component.
ELECTROSTATIC DISCHARGE (ESD) SENSITIVE
DEVICES
All ESD sensitive components are solid state and a
symbol (Fig. 2) is used to indicate this. When hanÂdling any component with this symbol comply with
the following procedures to reduce the possibility of
electrostatic charge build up on the body and inadÂvertent discharge into the component. If it is not
known whether the part is ESD sensitive, assume
that it is.
(1) Always touch a known good ground before hanÂdling the part. This should be repeated while hanÂdling the part and more frequently after sliding
across a seat, sitting down from a standing position,
or walking a distance.
(2) Avoid touching electrical terminals of the part,
unless instructed to do so by a written procedure.
(3) When using a voltmeter, be sure to connect the
ground lead first.
(4) Do not remove the part from its protective
packing until it is time to install the part.
(5) Before removing the part from its package,
ground the package to a known good ground on the
vehicle.
• Jumper Wire - This is a test wire used to conÂnect two points of a circuit. It can be used to bypass
an open in a circuit.
WARNING: NEVER USE A JUMPER WIRE ACROSS
A LOAD, SUCH AS AMOTOR, CONNECTED
BETWEEN A BATTERY FEED AND GROUND.
• Voltmeter - Used to check for voltage on a cirÂcuit. Always connect the black lead to a known good
ground and the red lead to the positive side of the
circuit.
CAUTION: Most of the electrical components used
in today’s vehicle are solid state. When checking
voltages in these circuits use a meter with a 10-meÂgohm or greater impedance rating.
• Ohmmeter - Used to check the resistance
between two points of a circuit. Low or no resistance
in a circuit means good continuity.
CAUTION: - Most of the electrical components used
in today’s vehicle are Solid State. When checking
resistance in these circuits use a meter with a
10-megohm or greater impedance rating. In addiÂtion, make sure the power is disconnected from the
circuit. Circuits that are powered up by the vehicle
electrical system can cause damage to the equipÂment and provide false readings.
• Probing Tools - These tools are used for probing
terminals in connectors (Fig. 3). Select the proper
size tool from Special Tool Package 6807, and insert
it into the terminal being tested. Use the other end
of the tool to insert the meter probe.
Fig. 2 Electrostatic Discharge Symbol
DIAGNOSIS AND TESTING
TROUBLESHOOTING TOOLS
When diagnosing a problem in an electrical circuit
there are several common tools necessary. These tools
are listed and explained below.
Fig. 3 Probing Tool
1 – SPECIAL TOOL 6801
2 – PROBING END
INTERMITTENT AND POOR CONNECTIONS
Most intermittent electrical problems are caused
by faulty electrical connections or wiring. It is also
possible for a sticking component or relay to cause a
problem. Before condemning a component or wiring
assembly check the following items.
Page 11
PL8W - 01 GENERAL INFORMATION8W - 01 - 9
DIAGNOSIS AND TESTING (Continued)
• Connectors are fully seated
• Spread terminals, or terminal push out
• Terminals in the wiring assembly are fully
seated into the connector/component and locked in
position
• Dirt or corrosion on the terminals. Any amount
of corrosion or dirt could cause an intermittent probÂlem
• Damaged connector/component casing exposing
the item to dirt and moisture
• Wire insulation that has rubbed through causing
a short to ground
• Some or all of the wiring strands broken inside
of the insulation covering
• Wiring broken inside of the insulation.
TROUBLESHOOTING TESTS
Before beginning any tests on a vehicles electrical
system use the Wiring Diagrams and study the cirÂcuit. Also refer to the Troubleshooting Wiring ProbÂlems in this section.
TESTING FOR VOLTAGE POTENTIAL
(1) Connect the ground lead of a voltmeter to a
known good ground (Fig. 4).
(2) Connect the other lead of the voltmeter to the
selected test point. The vehicle ignition may need to
be turned ON to check voltage. Refer to the appropriÂate test procedure.
(2) Connect one lead of the ohmmeter to one side
of the circuit being tested (Fig. 5).
(3) Connect the other lead to the other end of the
circuit being tested. Low or no resistance means good
continuity.
Fig. 5 Testing for Continuity
1 – FUSE REMOVED FROM CIRCUIT
Fig. 4 Testing for Voltage Potential
TESTING FOR CONTINUITY
(1) Remove the fuse for the circuit being checked
or, disconnect the battery.
TESTING FOR A SHORT TO GROUND
(1) Remove the fuse and disconnect all items
involved with the fuse.
(2) Connect a test light or a voltmeter across the
terminals of the fuse.
(3) Starting at the fuse block, wiggle the wiring
harness about six to eight inches apart and watch
the voltmeter/test lamp.
(4) If the voltmeter registers voltage or the test
lamp glows, there is a short to ground in that genÂeral area of the wiring harness.
TESTING FOR A SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS
(1) Refer to the wiring diagrams and disconnect or
isolate all items on the suspected fused circuits.
(2) Replace the blown fuse.
(3) Supply power to the fuse by turning ON the
ignition switch or re-connecting the battery.
(4) Start connecting the items in the fuse circuit
one at a time. When the fuse blows the circuit with
the short to ground has been isolated.
TESTING FOR A VOLTAGE DROP
(1) Connect the positive lead of the voltmeter to
the side of the circuit closest to the battery (Fig. 6).
Page 12
8W - 01 - 108W - 01 GENERAL INFORMATIONPL
DIAGNOSIS AND TESTING (Continued)
(2) Connect the other lead of the voltmeter to the
other side of the switch or component.
(3) Operate the item.
(4) The voltmeter will show the difference in volt-
age between the two points.
Fig. 6 Testing for Voltage Drop
TROUBLESHOOTING WIRING PROBLEMS
When troubleshooting wiring problems there are
six steps which can aid in the procedure. The steps
are listed and explained below. Always check for non-
factory items added to the vehicle before doing any
diagnosis. If the vehicle is equipped with these items,
disconnect them to verify these add-on items are not
the cause of the problem.
(1) Verify the problem.
(2) Verify any related symptoms. Do this by perÂforming operational checks on components that are
in the same circuit. Refer to the wiring diagrams.
(3) Analyze the symptoms. Use the wiring diaÂgrams to determine what the circuit is doing, where
the problem most likely is occurring and where the
diagnosis will continue.
(4) Isolate the problem area.
(5) Repair the problem.
(6) Verify proper operation. For this step check for
proper operation of all items on the repaired circuit.
Refer to the wiring diagrams.
SERVICE PROCEDURES
WIRING REPAIR
When replacing or repairing a wire, it is important
that the correct gage be used as shown in the wiring
diagrams. The wires must also be held securely in
place to prevent damage to the insulation.
(1) Disconnect battery negative cable.
(2) Remove 1 inch of insulation from each end of
the wire.
(3) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.
(4) Spread the strands of the wire apart on each
part of the exposed wire (example 1) (Fig. 7).
(5) Push the two ends of wire together until the
strands of wire are close to the insulation (example
2) (Fig. 7).
(6) Twist the wires together (example 3) (Fig. 7).
(7) Solder the connection together using rosin core
type solder only. Do not use acid core solder.
(8) Center the heat shrink tubing over the joint,
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(9) Secure the wire to the existing ones to prevent
chafing or damage to the insulation.
(10) Connect battery and test all affected systems.
1 – EXAMPLE 1
2 – EXAMPLE 2
3 – EXAMPLE 3
Fig. 7 Wire Repair
Page 13
PL8W - 01 GENERAL INFORMATION8W - 01 - 11
SERVICE PROCEDURES (Continued)
TERMINAL/CONNECTOR REPAIR-MOLEX
CONNECTORS
(1) Disconnect battery.
(2) Disconnect the connector from its mating half/
component.
(3) Insert the terminal releasing special tool 6742
into the terminal end of the connector (Fig. 8).
Fig. 8 Molex Connector Repair
1 – CONNECTOR
2 – SPECIAL TOOL 6742
TERMINAL/CONNECTOR REPAIR—THOMAS
AND BETTS CONNECTORS
(1) Disconnect battery.
(2) Disconnect the connector from its mating half/
component.
(3) Push in the two lock tabs on the side of the
connector (Fig. 10).
Fig. 10 Thomas and Betts Connector Lock Release
Tabs
1 – LOCK TABS
(4) Using special tool 6742 release the locking fin-
gers on the terminal (Fig. 9).
(5) Pull on the wire to remove it from the connec-
tor.
(6) Repair or replace the connector or terminal, as
necessary.
Fig. 9 Using Special Tool 6742
1 – CONNECTOR
2 – SPECIAL TOOL 6742
(4) Insert the probe end of special tool 6934 into
the back of the connector cavity (Fig. 11).
(5) Grasp the wire and tool 6934 and slowly
remove the wire and terminal from the connector.
Fig. 11 Removing Wire Terminal
1 – SPECIAL TOOL 6934
(6) Repair or replace the terminal.
Page 14
8W - 01 - 128W - 01 GENERAL INFORMATIONPL
SERVICE PROCEDURES (Continued)
(7) Install the wire and terminal in the connector.
Fully seat the terminal in the connector.
(8) Push in the single lock tab on the side of the
connector (Fig. 12).
Fig. 14 Using Special Tool 6932
1 – SPECIAL TOOL 6932
2 – CONNECTOR
Fig. 12 Single Lock Tab
1 – SINGLE LOCK TAB
TERMINAL/CONNECTOR REPAIR- AUGAT
CONNECTORS
(1) Disconnect battery.
(2) Disconnect the connector from its mating half/
component.
(3) Push down on the yellow connector locking tab
to release the terminals (Fig. 13).
(5) Repair or replace the connector or terminal as
necessary.
(6) When re-assembling the connector, the locking
wedge must be placed in the locked position to preÂvent terminal push out.
CONNECTOR REPLACEMENT
(1) Disconnect battery.
(2) Disconnect the connector that is to be repaired
from its mating half/component.
(4) Position the connector locking finger away from
the terminal using the proper pick from special tool
Page 15
PL8W - 01 GENERAL INFORMATION8W - 01 - 13
SERVICE PROCEDURES (Continued)
kit 6680. Pull on the wire to remove the terminal
from the connector (Fig. 16) (Fig. 17).
(5) Reset the terminal locking tang, if it has one.
(6) Insert the removed wire in the same cavity on
the repair connector.
(7) Repeat steps four through six for each wire in
the connector, being sure that all wires are inserted
into the proper cavities. For additional connector pinÂout identification, refer to the wiring diagrams.
(8) Insert the connector locking wedge into the
repaired connector, if required.
(9) Connect connector to its mating half/compoÂnent.
(10) Connect battery and test all affected systems.
Fig. 16 Terminal Removal
1 – CONNECTOR
2 – FROM SPECIAL TOOL KIT 6680
CONNECTOR AND TERMINAL REPLACEMENT
Fig. 17 Terminal Removal Using Special Tool
1 – FROM SPECIAL TOOL KIT 6680
2 – CONNECTOR
(1) Disconnect battery.
(2) Disconnect theconnector (thatisto be
repaired) from its mating half/component.
(3) Cut off the existing wire connector directly
behind the insulator. Remove six inches of tape from
the harness.
(4) Stagger cut all wires on the harness side at 1/2
inch intervals (Fig. 18).
(5) Remove 1 inch of insulation from each wire on
the harness side.
(6) Stagger cut the matching wires on the repair
connector assembly in the opposite order as was done
on the harness side of the repair. Allow extra length
for soldered connections. Check that the overall
length is the same as the original (Fig. 18).
(7) Remove 1 inch of insulation from each wire.
(8) Place a piece of heat shrink tubing over one
side of the wire. Be sure the tubing will be long
enough to cover and seal the entire repair area.
(9) Spread the strands of the wire apart on each
part of the exposed wires.
(10) Push the two ends of wire together until the
strands of wire are close to the insulation.
(11) Twist the wires together.
(12) Solder the connection together using rosin
core type solder only. Do not use acid core solder.
(13) Center the heat shrink tubing over the joint
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(14) Repeat steps 8 through 13 for each wire.
(15) Re-tape the wire harness starting 1-1/2 inches
behind the connector and 2 inches past the repair.
(16) Re-connect the repaired connector.
Page 16
8W - 01 - 148W - 01 GENERAL INFORMATIONPL
SERVICE PROCEDURES (Continued)
kit 6680. Pull on the wire to remove the terminal
from the connector (Fig. 20) (Fig. 21).
(17) Connect the battery, and test all affected sys-
tems.
TERMINAL REPLACEMENT
(1) Disconnect battery.
(2) Disconnect the connector being repaired from
its mating half. Remove connector locking wedge, if
required (Fig. 19).
(3) Remove connector locking wedge, if required
(Fig. 19).
Fig. 19 Connector Locking Wedge Tab (Typical)
1 – CONNECTOR
2 – CONNECTOR LOCKING WEDGE TAB
(4) Position the connector locking finger away from
the terminal using the proper pick from special tool
Fig. 21 Terminal Removal Using Special Tool
1 – FROM SPECIAL TOOL KIT 6680
2 – CONNECTOR
(5) Cut the wire 6 inches from the back of the con-
nector.
(6) Remove 1 inch of insulation from the wire on
the harness side.
(7) Select a wire from the terminal repair assem-
bly that best matches the color wire being repaired.
(8) Cut the repair wire to the proper length and
remove 1 inch of insulation.
(9) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.
(10) Spread the strands of the wire apart on each
part of the exposed wires.
Page 17
PL8W - 01 GENERAL INFORMATION8W - 01 - 15
SERVICE PROCEDURES (Continued)
(11) Push the two ends of wire together until the
strands of wire are close to the insulation.
(12) Twist the wires together.
(13) Solder the connection together using rosin
core type solder only. Do not use acid core solder.
(14) Center the heat shrink tubing over the joint
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(15) Insert the repaired wire into the connector.
(16) Installtheconnectorlockingwedge,if
required, and reconnect the connector to its mating
half/component.
(17) Re-tape the wire harness starting 1-1/2 inches
behind the connector and 2 inches past the repair.
(18) Connect battery, and test all affected systems.
DIODE REPLACEMENT
(1) Disconnect the battery.
(2) Locate the diode in the harness, and remove
the protective covering.
(3) Remove the diode from the harness, pay attenÂtion to the current flow direction (Fig. 22).
(4) Remove the insulation from the wires in the
harness. Only remove enough insulation to solder in
the new diode.
(5) Install the new diode in the harness, making
sure current flow is correct. If necessary refer to the
appropriate wiring diagram for current flow.
(6) Solder the connection together using rosin core
type solder only. Do not use acid core solder.
(7) Tape the diode to the harness using electrical
tape making, sure the diode is completely sealed
from the elements.
(8) Re-connect the battery, and test affected sysÂtems.
Fig. 22 Diode Identification
1 – CURRENT FLOW
2 – BAND AROUND DIODE INDICATES CURRENT FLOW
3 – DIODE AS SHOWN IN THE DIAGRAMS
Page 18
8W - 01 - 168W - 01 GENERAL INFORMATIONPL
SPECIAL TOOLS
WIRING/TERMINAL
Terminal Removing Tool 6932
Probing Tool Package 6807
Terminal Pick 6680
Terminal Removing Tool 6934
Page 19
PL8W - 02 COMPONENT INDEX8W - 02 - 1
8W-02 COMPONENT INDEX
ComponentPage
A/C Compressor Clutch Relay ............ 8W-42
A/C Compressor Clutch ................. 8W-42
A/C Cycling Switch .................... 8W-42
A/C Heater Blower Motor ............... 8W-42
A/C Heater Control .................... 8W-42
A/C Pressure Switches.................. 8W-42
Airbag Control Module ................. 8W-43
Airbags ............................. 8W-43
Antenna ............................. 8W-47
Automatic Shut Down Relay ............. 8W-30
Back-Up Lamp Switch .................. 8W-51
Back-Up Lamps ....................... 8W-51
Battery ............................. 8W-20
Blower Motor Resistor Block ............. 8W-42
Brake Lamp Switch .................... 8W-30
Brake Shift Interlock Solenoid ........... 8W-30
Brake Warning Indicator Switch .......... 8W-40
Camshaft Position Sensor ............... 8W-30
Cargo Lamp .......................... 8W-44
Center High Mounted Stop Lamp ......... 8W-51
Center Stack Lamp .................... 8W-44
Cigar Lighter/Power Outlet .............. 8W-41
Circuit Breakers (FB) .................. 8W-11
City Lamps .......................... 8W-50
Clockspring ..................... 8W-33, 41, 43
Clutch Interlock Switch ................. 8W-30
Combination Flasher ................... 8W-52
Controller Anti-Lock Brake .............. 8W-35
Crankshaft Position Sensor .............. 8W-30
Data Link Connector ................... 8W-30
Decklid Release Switch ................. 8W-44
Decklid Solenoid ...................... 8W-61
Diode No. 1 .......................... 8W-42
Dome Lamp .......................... 8W-44
Dome Lamp/Intrusion Sensor ............ 8W-44
Door Ajar Switches .................... 8W-40
Door Lock Motors ..................... 8W-61
Engine Coolant Temperature Sensor ....... 8W-30
Engine Oil Pressure Switch .............. 8W-30
Engine Starter Motor Relay ............. 8W-21
Engine Starter Motor .................. 8W-21
Fog Lamps ........................ 8W-50, 51
Front Fog Lamp Switch ................. 8W-50
Fuel Injectors ........................ 8W-30
Fuel Pump Module .................... 8W-30
Fuel Pump Relay ...................... 8W-30
Fuel Tank ........................... 8W-30
Fuses (FB) ........................... 8W-11
Fuses (PDC) ......................... 8W-10
Fuse Block ........................... 8W-11
Fusible Link A11 ................... 8W-20, 21
Grounds ............................. 8W-15
ComponentPage
Generator ........................... 8W-20
Glove Box Lamp/Switch................. 8W-44
Headlamp Beam Select .............. 8W-40, 50
Headlamp Leveling Motors .............. 8W-50
Headlamp Leveling Switch Illumination .... 8W-50
Headlamp Leveling Switch .............. 8W-50
Headlamp Switch ................... 8W-50, 51
Headlamps .......................... 8W-50
Horns .............................. 8W-41
Horn Relay .......................... 8W-41
Horn Switch ......................... 8W-41
Hood Ajar Switch...................... 8W-39
Idle Air Control Motor .................. 8W-30
Ignition Coil ......................... 8W-30
Ignition Switch ....................... 8W-10
Indicators ........................... 8W-40
Indicator Drivers ...................... 8W-40
Inlet Air Temperature Sensor ............ 8W-30
Instrument Cluster .................... 8W-40
Instrument Panel Drivers ............... 8W-40
Knock Sensor ......................... 8W-30
Leak Detection Pump .................. 8W-30
License Lamps ........................ 8W-51
Manifold Absolute Pressure Sensor ........ 8W-30
Map/Reading Lamps ................... 8W-44
Multi- Function Switch ......... 8W-40, 50, 51, 52