Dodge 2015 RAM 1500, 2015 RAM 3500, 2015 RAM 2500 User Manual

Download

Page 1

Page 2

If you are the rst registered retail owner of your vehicle,

you may obtain a complimentary printed copy of the Owner’s

Manual, Navigation/Uconnect

Manuals or Warranty Booklet

by calling 1-866-726-4636 (U.S.) or 1-800-387-1143 (Canada)

or by contacting your dealer.

IMPORTANT

This User Guide is intended to familiarize you with the

important features of your vehicle. The DVD enclosed

contains your Owner’s Manual, Navigation/Uconnect

Manuals, Warranty Booklets, Tire Warranty and Roadside

Assistance (new vehicles purchased in the U.S.) or Roadside

Assistance (new vehicles purchased in Canada) in electronic

format. We hope you nd it useful. Replacement DVD kits

may be purchased by visiting www.techauthority.com.

The driver’s primary responsibility is the safe operation of the vehicle. Driving

while distracted can result in loss of vehicle control, resulting in a collision and

personal injury. FCA US LLC strongly recommends that the driver use extreme

caution when using any device or feature that may take their attention

off the road. Use of any electrical devices, such as cellular telephones,

computers, portable radios, vehicle navigation or other devices, by the driver

while the vehicle is moving is dangerous and could lead to a serious collision.

Texting while driving is also dangerous and should never be done while the

vehicle is moving. If you nd yourself unable to devote your full attention to

vehicle operation, pull off the road to a safe location and stop your vehicle.

Some states or provinces prohibit the use of cellular telephones or texting while

driving. It is always the driver’s responsibility to comply with all local laws.

Page 3

INTRODUCTION/WELCOME

WELCOME FROM FCA US LLC .......3

CONTROLS AT A GLANCE

DRIVER COCKPIT ...............6

INSTRUMENT CLUSTER ...........8

GETTING STARTED

KEYFOB ...................10

KEYLESS ENTER-N-GO™ ......... 13

REMOTE START ............... 15

VEHICLE SECURITY ALARM .......16

SEAT BELT SYSTEMS ........... 17

SUPPLEMENTAL RESTRAINT SYSTEM

(SRS) — AIR BAGS ............18

CHILD RESTRAINTS ............20

HEAD RESTRAINTS ............. 28

FRONT SEATS ................30

HEATED/VENTILATED SEATS ....... 32

HEATED STEERING WHEEL ........34

TILT STEERING COLUMN .........35

POWER FOLDING OUTSIDE MIRRORS FOR STANDARD AND TRAILER TOW

...36

OPERATING YOUR VEHICLE

ENGINE BREAK-IN

RECOMMENDATIONS ............ 37

TURN SIGNALS/WIPER/WASHER/HIGH

BEAMS LEVER ................38

HEADLIGHT SWITCH ............ 39

ELECTRONIC SPEED CONTROL ..... 40

EIGHT-SPEED AUTOMATIC

TRANSMISSION — IF EQUIPPED ....42

ELECTRONIC RANGE SELECT (ERS)

OPERATION .................43

1500 AIR SUSPENSION SYSTEM .... 44

2500-3500 AIR SUSPENSION

SYSTEM ....................47

STOP/START SYSTEM — IF EQUIPPED . . 49 MANUAL CLIMATE CONTROLS

WITHOUT TOUCHSCREEN ........ 52

MANUAL CLIMATE CONTROLS

WITH TOUCHSCREEN ...........53

AUTOMATIC CLIMATE CONTROLS

WITH TOUCHSCREEN ...........55

PARKSENSE

PARK ASSIST ................ 57

PARKVIEW®REAR BACK-UP CAMERA

POWER SLIDING REAR WINDOW .... 58

POWER SUNROOF .............59

WIND BUFFETING .............61

FRONT AND REAR

..58

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM . . . 62

IDENTIFYING YOUR RADIO ........64

Uconnect Uconnect

Uconnect®5.0 ................85

Uconnect

Uconnect®8.4AN ............. 124

Uconnect®PHONE ............138

STEERING WHEEL AUDIO

CONTROLS ................. 148

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) OR DRIVER

INFORMATION DISPLAY (DID) .....148

PROGRAMMABLE FEATURES ...... 149

UNIVERSAL GARAGE DOOR OPENER (HomeLink

POWER INVERTER ............155

POWER OUTLETS .............156

AUXILIARY SWITCHES —

IF EQUIPPED ................158

ACCESS ............. 66

3.0 ................82

8.4A ...............96

) ................ 152

OFF-ROAD CAPABILITIES

ELECTRONICALLY SHIFTED FOUR WHEEL DRIVE OPERATION . . . 159

UTILITY

TONNEAU COVER .............162

EASY-OFF TAILGATE ...........162

PICKUP BOX ................163

RAMBOX

TOWING & PAYLOAD ........... 169

TOW/HAUL MODE ............169

INTEGRATED TRAILER BRAKE

MODULE .................. 170

RECREATIONAL TOWING

(BEHIND MOTORHOME, ETC.) .....172

..................165

1500 3.0L DIESEL

DIESEL ENGINE BREAK-IN

RECOMMENDATIONS ...........178

DIESEL ENGINE STARTING

PROCEDURES ...............178

DIESEL FUEL FILTER/WATER

SEPARATOR.................180

EXHAUST REGENERATION .......181

COOL-DOWN IDLE CHART ........ 182

ADDING FUEL — DIESEL ENGINE

ONLY .....................183

DIESEL EXHAUST FLUID ........184

Page 4

TABLE OF CONTENTS

6.7L CUMMINS® DIESEL

DIESEL ENGINE BREAK-IN

RECOMMENDATIONS ...........188

DIESEL ENGINE STARTING

PROCEDURES ...............188

DIESEL EXHAUST BRAKE

(ENGINE BRAKING) ...........190

IDLE-UP FEATURE (AUTOMATIC

TRANSMISSION ONLY) .........191

ENGINE MOUNTED FUEL

FILTER/WATER SEPARATOR .......192

UNDERBODY MOUNTED FUEL

FILTER/WATER SEPARATOR .......193

EXHAUST REGENERATION .......194

COOL-DOWN IDLE CHART ........ 196

ADDING FUEL — DIESEL ENGINE

ONLY .....................197

DIESEL EXHAUST FLUID ........198

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE .........203

INSTRUMENT CLUSTER WARNING

LIGHTS ................... 203

INSTRUMENT CLUSTER INDICATOR

LIGHTS ................... 209

IF YOUR ENGINE OVERHEATS .....211

JACKING AND TIRE CHANGING .... 212

JUMP-STARTING PROCEDURES ....225

EMERGENCY TOW HOOKS ....... 228

SHIFT LEVER OVERRIDE ........ 228

MANUAL PARK RELEASE —

EIGHT SPEED TRANSMISSION .....229

TOWING A DISABLED VEHICLE .... 231

FREEING A STUCK VEHICLE ......231

EVENT DATA RECORDER (EDR) .....232

MAINTAINING YOUR VEHICLE

OPENING THE HOOD ..........233

ENGINE COMPARTMENT ........234

FLUID CAPACITIES — GAS ENGINE FLUIDS, LUBRICANTS AND GENUINE PARTS — GAS ENGINE . . . 247

...246

FLUID CAPACITIES —

1500 3.0 DIESEL .............249

FLUIDS, LUBRICANTS, AND GENUINE PARTS —

1500 3.0 DIESEL .............249

FLUID CAPACITIES —

6.7L CUMMINS FLUIDS, LUBRICANTS, AND GENUINE PARTS — 6.7L CUMMINS ENGINE

MAINTENANCE PROCEDURES .....254

MAINTENANCE SCHEDULE —

GASOLINE ENGINE ............254

MAINTENANCE SCHEDULE —

1500 3.0L DIESEL ENGINE .......259

MAINTENANCE SCHEDULE —

6.7L CUMMINS DIESEL ENGINE .... 264

FUSES .................... 271

TIRE PRESSURES .............275

SPARE TIRES — IF EQUIPPED ..... 276

WHEEL AND WHEEL TRIM CARE . . . 277

REPLACEMENT BULBS .........278

DIESEL ENGINE . . . 251

...................252

DIESEL

CUSTOMER ASSISTANCE

FCA US LLC CUSTOMER CENTER . . . 279 FCA CANADA INC. CUSTOMER

CENTER .................. 279

ASSISTANCE FOR THE HEARING

IMPAIRED ................. 279

PUBLICATIONS ORDERING .......279

REPORTING SAFETY DEFECTS IN

THEUNITEDSTATES ...........280

MOPAR® ACCESSORIES

AUTHENTIC ACCESSORIES BY MOPAR

................281

FAQ’s

FREQUENTLY ASKED QUESTIONS . . . 282

INDEX

...................284

Page 5

INTRODUCTION/WELCOME

WELCOME FROM FCA US LLC

Congratulations on selecting your new FCA US LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

Your new FCA US LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place. Always drive carefully.

Your new vehicle has many features for the comfort and convenience of you and your passengers. Some of these should not be used when driving because they take your eyes from the road or your attention from driving. Never text while driving or take your eyes more than momentarily off the road.

This guide illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This guide may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this guide that are not available on this vehicle. FCA US LLC reserves the right to make changes in design and specifications and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

This User Guide has been prepared to help you quickly become acquainted with the important features of your vehicle. It contains most things you will need to operate and maintain the vehicle, including emergency information.

The DVD includes a computer application containing detailed owner's information which can be viewed on a personal computer or MAC computer. The multimedia DVD also includes videos which can be played on any standard DVD player (including the Uconnect DVD operational information is located on the back of the DVD sleeve.

For complete owner information, refer to your Owner's Manual on the DVD in the owner’s kit provided at the time of new vehicle purchase. For your convenience, the information

contained on the DVD may also be printed and saved for future reference.

FCA US LLC is committed to protecting our environment and natural resources. By converting from paper to electronic delivery for the majority of the user information for your vehicle, together we greatly reduce the demand for tree-based products and lessen the stress on our environment.

Touchscreen Radios if equipped with DVD player capabilities). Additional

Page 6

INTRODUCTION/WELCOME

VEHICLES SOLD IN CANADA

With respect to any vehicles sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution (excluding legal lines).

WARNING!

• Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.

• Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control.

• Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle.

• Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.

• Never use the “PARK” position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.

• Refer to your Owner's Manual on the DVD for further details.

Page 7

INTRODUCTION/WELCOME

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

The use of aftermarket devices including cell phones, MP3 players, GPS systems, or chargers may affect the performance of on-board wireless features including Keyless Enter-N-Go™ and Remote Start range. If you are experiencing difficulties with any of your wireless features, try disconnecting your aftermarket devices to see if the situation improves. If your symptoms persist, please see an authorized dealer.

CHRYSLER, DODGE, JEEP, RAM, MOPAR and Uconnect are registered trademarks of FCA US LLC.

Page 8

CONTROLS AT A GLANCE

DRIVER COCKPIT

1. Headlight Switch pg. 39

2. Electronic Vehicle Information Center (EVIC) Controls Or Driver Information Display (DID) Controls pg. 148

3. Turn Signal/Wiper/Washer/High Beams Lever pg. 38

4. Instrument Cluster pg. 8

5. Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID) pg. 148

6. Electronic Speed Control pg. 40

7. Engine Starting/Stopping pg. 14

8. Four Wheel Drive Operation pg. 159

9. Uconnect

10. Climate Controls pg. 52

Radio pg. 64

Page 9

CONTROLS AT A GLANCE

11. Switch Panel

12. Power Inverter Outlet pg. 155

13. Glove Compartment

14. Power Outlet

15. Shift Lever

16. Hood Release (below steering wheel at base of instrument panel) pg. 233

17. Parking Brake Release

18. Power Windows

19. Power Door Locks

20. Power Mirrors

Page 10

CONTROLS AT A GLANCE

INSTRUMENT CLUSTER

1. Temperature Gauge

2. Tachometer

3. Voltmeter

(See page 203 for Instrument Cluster Warning Lights.)

Page 11

CONTROLS AT A GLANCE

Electronic Vehicle Information Center (EVIC) Or Driver Information Display (DID)

5. Oil Pressure Gauge

6. Speedometer

7. Fuel Gauge

(See page 209 for Instrument Cluster Indicator Lights.)

Page 12

GETTING STARTED

KEY FOB

This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment.

The Keyless Push Button Ignition has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START, during start RUN will illuminate.

Key Fob

1 — Air Suspension 2 — Unlock 3 — Lock 4 — Remote Start 5 — Panic

Page 13

GETTING STARTED

NOTE:

In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.

The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three with detents and one that is spring-loaded. The detent positions are OFF, ACC, and ON/ RUN. The START position is a springloaded momentary contact position. When released from the START position, the switch automatically returns to the ON/RUN position.

Key Fob

1 — Lock 2 — Unlock 3 — Remote Start 4 — Emergency Key Release 5 — Emergency Key

Page 14

GETTING STARTED

Locking And Unlocking The Doors

Push and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door. Push and release the UNLOCK button twice within five seconds to unlock all doors and the tailgate and the RamBox (if equipped). The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.

All doors can be programmed to unlock on the first push of the UNLOCK button. Refer to “Uconnect Customer Programmable Features” in “Electronics” for further information.

Panic Alarm

1. Push the PANIC button once to turn the Panic Alarm on.

2. Wait approximately three seconds and push the button a second time to turn the Panic Alarm off.

RKE Air Suspension (Remote Lowering Of Vehicle) — If Equipped

• This vehicle is equipped with a feature that can lower the vehicle to a height which

will improve ease of passenger entry/exit and cargo loading/unloading. The feature is accessed by pushing the air suspension lowering button twice on the Key Fob.

• When remote Key Fob lowering is requested the vehicle will send a series of chirps

and flashes to alert the customer that the operation has begun and will continue these alerts until it successfully lowers.

• If the feature is unable to lower the vehicle due to certain conditions not being

met, the horn will chirp twice and the vehicle will not lower.

Emergency Key

Should the battery in the vehicle or the Key Fob transmitter go dead, there is an emergency key located in the Key Fob that can be used for locking and unlocking the doors.

• To remove the emergency key, slide the button on the Key Fob with your thumb

and then pull the key out with your other hand.

Page 15

GETTING STARTED

WARNING!

• Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the transmission gear selector. Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. A child could start the vehicle, operate power windows, other controls, or move the vehicle.

• Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause them to be severely injured or killed.

KEYLESS ENTER-N-GO™

The Keyless Enter-N-Go™ system is an enhancement to the vehicle's Key Fob. This feature allows you to lock and unlock the vehicle's door(s) without having to push Key Fob lock or unlock buttons, as well as starting and stopping the vehicle with the push of a button.

To Unlock From The Driver Or Passenger Side:

With a valid Keyless Enter-N-Go™ Key Fob located outside the vehicle and within 5 ft (1.5m) of the driver or passenger side door handle, grab either front door handle to unlock the door automatically.

Grab The Door Handle To Unlock

Page 16

GETTING STARTED

To Lock The Vehicle’s Doors:

With a valid Keyless Enter-N-Go™ Key Fob transmitter within 5 ft (1.5 m) of the driver or passenger front door handles, push door handle LOCK button to lock all doors.

Do NOT grab the door handle, when pushing the door handle lock button. This could unlock the door(s).

Push The Button To Lock Do NOT Grab The Handle When Locking

NOTE:

• After pushing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle without the vehicle reacting and unlocking.

• The Passive Entry system will not operate if the RKE transmitter battery is dead.

The vehicle doors can also be locked by using the RKE transmitter lock button or the lock button located on the vehicles interior door panel.

Engine Starting/Stopping

Starting

With a valid Keyless Enter-N-Go™ Key Fob inside the vehicle:

1. Shift the transmission into PARK.

2. While pushing the brake pedal, push

the ENGINE START/STOP button once. If the engine fails to start, the starter will disengage automatically after 10 seconds.

To stop the cranking of the engine prior to the engine starting, push the button again.

Start/Stop Button

Page 17

GETTING STARTED

NOTE:

In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side of the Key Fob (side opposite of the Emergency Key) against the ENGINE START/STOP button and push to operate the ignition switch.

Stopping

1. Bring the vehicle to a complete stop.

2. Shift the transmission to PARK (P).

3. Push the ENGINE START/STOP button once. The ignition switch will return to the OFF position.

NOTE:

If the transmission is not in PARK and the vehicle is in motion, the ENGINE START/STOP button must be held for two seconds with the vehicle speed above 5 mph (8 km/h) before the engine will shut off.

REMOTE START

• Push REMOTE START button on the Key Fob twice within five seconds.

Pushing the REMOTE START

• To drive the vehicle, push and release the UNLOCK button on the RKE transmitter

to unlock the doors and disarm the Vehicle Security Alarm System (if equipped). Then cycle the ignition to the ON/RUN position.

With Remote Start, the engine will only run for 15 minutes (timeout) unless the ignition is cycled to the ON/RUN position.

The vehicle must be started with the Key Fob after two consecutive timeouts.

button a third time shuts the engine off.

WARNING!

• Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause you or others to be severely injured or killed when inhaled.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause you and others to be severely injured or killed.

Page 18

GETTING STARTED

VEHICLE SECURITY ALARM

The Vehicle Security Alarm monitors the vehicle doors for unauthorized entry and the Keyless Enter-N-Go™ START/STOP button for unauthorized operation. While the Vehicle Security Alarm is armed, interior switches for door locks and decklid release are disabled. If something triggers the alarm, the Vehicle Security Alarm will provide the following audible and visible signals: the horn will pulse, the park lamps and/or turn signals will flash, and the Vehicle Security Light in the instrument cluster will flash.

To Arm The System:

Lock the door using either the power door lock switch (one door must be open) or the LOCK button on the Remote Keyless Entry (RKE) transmitter (doors can be open or closed), and close all doors.

The Vehicle Security Light in the instrument cluster will flash for 16 seconds. This shows that the Vehicle Security Alarm is arming. During this period, if a door is opened, the ignition is cycled to ON/RUN, or the power door locks are unlocked in any manner, the Vehicle Security Alarm will automatically disarm.

NOTE:

• The Vehicle Security Alarm will not arm if you lock the doors with the manual door lock plungers.

• Once armed, the Vehicle Security Alarm disables the unlock switch on the driver door trim panel and passenger door trim panel.

To Disarm The System:

Push the Key Fob UNLOCK button or cycle the ignition to the ON/RUN position.

The Vehicle Security Alarm is designed to protect your vehicle. However, you can create conditions where the Vehicle Security Alarm will give you a false alarm. If one of the previously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm.

If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm.

Page 19

GETTING STARTED

SEAT BELT SYSTEMS

Lap/Shoulder Belts

• All seating positions except the Quad Cab®, Mega Cab®and Crew Cab front center seating position have combination lap/shoulder belts.

• Be sure everyone in your vehicle is in a seat and using a seat belt properly.

• Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision.

• Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt.

Center Lap Belts

The center seating position for the Quad Cab®, Mega Cab®and Crew Cab front seat has a lap belt only. To buckle the lap belt, slide the latch plate into the buckle until you hear a "click." To lengthen the lap belt, tilt the latch plate and pull.

Seat Belt Pretensioner

• The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision.

• A deployed pretensioner or a deployed air bag must be replaced immediately.

WARNING!

• In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

• A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

• A seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

•

A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision.

Page 20

GETTING STARTED

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

Air Bag System Components

Your vehicle may be equipped with the following air bag system components:

• Occupant Restraint Controller (ORC)

• Air Bag Warning Light

• Steering Wheel and Column

• Instrument Panel

• Knee Impact Bolsters

• Advanced Front Air Bags

• Supplemental Side Air Bags

• Front and Side Impact Sensors (if equipped)

• Seat Belt Pretensioners

• Seat Belt Buckle Switch

Advanced Front Air Bags

• This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The Advanced Front Air Bags will not deploy in every type of collision.

• Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions.

• The Advanced Front Air Bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions.

• On the other hand, depending on the type and location of impact, Advanced Front Air Bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration.

• Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed.

• Seat belts are necessary for your protection in all collisions, and also are needed to help keep you in position, away from an inflating air bag.

• The air bags must be ready to inflate for your protection in a collision. The Occupant Restraint Controller (ORC) monitors the internal circuits and interconnecting wiring associated with air bag system electrical components.

• The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first turned to the ON/RUN position. After the self-check, the Air Bag Warning

Page 21

GETTING STARTED

Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial startup.

• The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ON/RUN position. If the ignition switch is in the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate.

• If the Air Bag Warning Light in the instrument panel is not on during the four to eight seconds when the ignition switch is first turned to the ON/RUN position, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately.

NOTE:

If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be ready to inflate for your protection. Have an authorized dealer service the air bag system immediately.

• After any collision, the vehicle should be taken to an authorized dealer immediately.

• Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

• If it is necessary to modify the air bag system for persons with disabilities, contact your authorized dealer.

• Refer to “Supplemental Restraint System (SRS)” in “Things To Know Before Starting Your Vehicle” in the Owner's Manual on the DVD for further information.

Supplemental Side Air Bags

• This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags (SABs) located in the outboard side of the front seats. The SABs are marked with a SRS AIRBAG label sewn into the outboard side of the seats.

• This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs) located above the side windows. The trim covering the SABICs is labeled SRS AIRBAG. The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events.

• The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts and certain rollover events. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular side impact or rollover event is appropriate, based on the severity and type of collision. Vehicle damage by itself is not a good indicator of whether or not Side Air Bags should have deployed.

Page 22

GETTING STARTED

WARNING!

• Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

• Being too close to the Side Air Bags during deployment could cause you to be severely injured or killed.

• Relying on the Side Air Bags alone could lead to more severe injuries in a collision. The Side Air Bags work with your seat belt to restrain you properly. In some collisions, Side Air Bags won’t deploy at all. Always wear your seat belt even though you have Side Air Bags.

• This vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtains (SABICs). Do not stack luggage or other cargo up high enough to block the deployment of the SABICs. The trim covering above the side windows where the SABIC and its deployment path are located should remain free from any obstructions.

• This vehicle is equipped with SABICs. In order for the SABICs to work as intended, do not install any accessory items in your vehicle which could alter the roof. Do not add an aftermarket sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason.

• Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury.

CHILD RESTRAINTS

Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.

NOTE:

•

For additional information, refer to

(1-866-732-8243 ).

• Canadian residents should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/eng/motorvehiclesafety/safedrivers-childsafety-index-53.htm

www.Seatcheck.org or call 1-866-SEATCHECK

Page 23

GETTING STARTED

LATCH — Lower Anchors And Tethers For CHildren (Crew/Quad Cab Full Bench)

• Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.

• The rear outboard seating positions have lower anchors and top tether anchors. The rear center seating position has a top tether anchor only.

LATCH – Lower Anchors And Tethers For CHildren (Crew/Mega/Quad Cab Split Bench)

• Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.

• All rear seating positions have lower anchors and top tether anchors.

LATCH System Weight Limit

You may use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg).

Locating LATCH Anchorages

The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.

1 — Lower Anchors

Page 24

GETTING STARTED

Locating Tether Anchorages

In addition, Regular Cab models have tether strap anchorages behind the front center and right seats. Quad Cab, Mega Cab and Crew Cab models have tether strap anchorages located behind each of the rear seats.

Center Seat LATCH (Regular/Quad/Crew Cab Full And Standard Bench)

Do not install a child restraint in the center position using the LATCH system. Use the seat belt and tether anchor to install a child seat in the center seating position.

Center Seat LATCH (Mega/Quad/Crew Cab Split Bench)

If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard position.

Installing The Child Restraint Using The LATCH Lower Anchors

NOTE:

Never “share” a LATCH anchorage with two or more child restraints.

Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages.

2. Attach the lower hooks or connectors of the child restraint to the lower anchorages

in the selected seating position.

3. If the child restraint has a tether strap, connect it to the top tether anchorage. See

below for directions to attach a tether anchor.

4. Tighten all of the straps as you push the child restraint rearward and downward

into the seat. Remove slack in the straps according to the child restraint manufacturer’s instructions.

5. Test that the child restraint is installed tightly by pulling back and forth on the

child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Installing The Child Restraint Using The Vehicle Seat Belts (Regular Cab)

The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

Page 25

GETTING STARTED

Installing The Child Restraint Using The Vehicle Seat Belts (Mega/Quad/Crew Cab Full And Split Bench)

The seat belts in the outboard passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR). The center seating positions are equipped with a cinching latch plate. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

Tether Anchorage Weight Limit

Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint.

To Install A Child Seat Using An ALR:

1. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path.

2. Slide the latch plate into the buckle until you hear a “click.”

3. Pull on the webbing to make the lap portion tight against the child seat.

4. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode.

5. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any webbing. If the retractor is not locked, repeat the last step.

6. Finally, pull up on any extra webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat.

7. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See below for directions to attach a tether anchor.

8. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Page 26

GETTING STARTED

To Install A Child Seat Using A Cinching Latch Plate:

1. Place the child seat in the center of the seating position.

2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path.

3. Slide the latch plate into the buckle until you hear a “click.”

4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat.

5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See below for directions to attach a tether anchor.

6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt):

When installing a forward-facing child restraint, always secure the top tether strap, up to the tether anchor weight limit, whether the child restraint is installed with the lower anchors or the vehicle seat belt.

Tether Strap Installation

Regular/Mega Cab Trucks:

In the regular cab truck, the top tether anchorages are located behind the center and right passenger seats. In the mega cab truck, the top tether anchorages are located behind each rear seating position. There is a plastic cover over each anchorage. To attach the tether strap of the child restraint:

1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint and to the tether anchor directly behind the seat.

2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head restraint and between its posts.

Lift the cover (if equipped) and attach the hook to the square opening in the sheet metal. Tighten the tether strap according to the child seat manufacturer’s instructions.

Page 27

GETTING STARTED

Quad/Crew Cab Trucks:

The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each seating position. Follow the steps below to attach the tether strap of the child restraint.

Right or Left Outboard Seats:

1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop.

Head Restraint In Raised Position Tether Strap Loop With Center Head

2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap loop behind the seat and over to the tether strap loop behind the center seat.

3. Pass the tether strap hook under the head restraint behind the child seat, through the tether strap loop behind the seat and over to the center tether strap loop.

Restraint In Raised Position

Tether Strap Through Outboard

Tether Strap Loop

Page 28

GETTING STARTED

4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions.

NOTE:

If there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats.

Tether Strap Through Outboard Tether

Strap Loop And Attached To Center

Tether Strap Loop

Center Seat:

1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop.

Tether Strap Loop With Head Restraint In

Raised Position

Page 29

GETTING STARTED

3. Pass the tether strap hook under the head restraint behind the child seat, through the tether strap loop behind the seat and over to the right or left outboard tether strap loop.

4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s instructions.

Tether Strap Through Center Tether Strap Loop

And Attached To Outboard Tether Strap Loop

Installing Three Child Restraints:

Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above.

Attach both hooks to the center tether strap loop, but do not tighten the straps yet.

Place a child restraint on the center rear seat. Route the tether strap following the directions for the center seating position, above.

4. Attach the hook to the outboard tether strap loop.

5. Tighten the tether straps according to the child seat manufacturer’s instructions, tightening the right and left tether straps before the center tether strap.

Left Outboard And Center Seating Position

Shown

Page 30

GETTING STARTED

WARNING!

• In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size.

• Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.

• Only use a rear-facing child restraint in a vehicle with a rear seat.

•

Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be severely injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.

• An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.

•

If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.

HEAD RESTRAINTS

Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.

WARNING!

The head restraints for all occupants must be properly installed and adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.

Front Head Restraints

To raise the head restraint pull upward on the head restraint. To lower the head restraint, push the adjustment button located on the base of the head restraint and push downward on the head restraint.

To remove the head restraint, raise it up as far as it can go then push the adjustment button and the release button at the base of each post while pulling the head restraint up. To reinstall the head restraint, put the head restraint posts into the holes then adjust it to the appropriate height.

Page 31

GETTING STARTED

WARNING!

• A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment.

• ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat.

NOTE:

Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.

Rear Head Restraints

The rear seats are equipped with adjustable and removable head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button located on the base of the head restraint and push downward on the head restraint.

To remove the head restraint, push the adjustment button and the release button while pulling upward on the whole assembly. To reinstall the head restraint, put the head restraint posts into the holes and adjust it to the appropriate height.

NOTE:

To remove outboard restraints, the rear seat bottom must be folded up.

WARNING!

A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment.

NOTE:

The rear center head restraint (Crew Cab and Quad Cab) has only one adjustment

• position that is used to aid in the routing of a tether. Refer to “Occupant Restraints” in “Things to Know Before Starting Your Vehicle” in the Owner's Manual on the DVD.

• Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.

WARNING!

ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat.

Page 32

GETTING STARTED

FRONT SEATS

Power Seats

The seat switch controls forward/backward and up/down. The recline switch controls the angle of the seatback.

• Push the switch forward or rearward and the seatback will move in either direction.

Power Lumbar

The lumbar controls are located on the outboard side of the seat cushion.

• The lumbar support can be increased by pushing the front of the switch and decreased by pushing the back of the switch.

Power Seat Switches

1 — Power Seat Switch 2 — Recline Switch 3 — Power Lumbar Switch

Memory Seat

The memory seat feature allows you to save the driver's seat position (excluding lumbar position), driver's outside mirror position, adjustable brake and accelerator pedals, Automatic Temperature Control (ATC) temperature setting and radio station preset settings. The driver's memory buttons are located on the outboard side of the driver's seat cushion.

• Adjust all memory profile settings, push the middle button S (SET), then push 1 or 2 within five seconds.

• To program a Key Fob to the memory position, place the ignition switch in the LOCK position and remove the Key Fob, push and release the LOCK button on the Key Fob to be programmed within five seconds of pushing button 1or2.

•

Push 1 or 2 to recall the saved positions, or push UNLOCK on the programmed Key Fob.

Refer to the Owner's Manual on the DVD for further details.

Memory Seat Button Location

Page 33

Manual Seats

Forward/Rearward

Lift up on the adjusting bar located at the front of the seat near the floor and release it when the seat is at the desired position. Then, using body pressure, move forward and backward on the seat to be sure that the seat adjusters have latched.

Recliner

Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position.

CAUTION!

GETTING STARTED

Manual Seat Adjusting Bar/Recline Lever

1 — Recline Lever 2 — Adjusting Bar

Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.

WARNING!

• Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.

• Actuating the recliner handle will allow the seatback to swing forward. Do not stand or lean in front of the seatback while actuating the handle. The seatback may swing forward and strike you, causing injury. To avoid possible injury, place your hand on the seatback while actuating the recliner handle.

• Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked.

Page 34

GETTING STARTED

HEATED/VENTILATED SEATS

Front Ventilated Seats

Located in the seat cushion are small fans that draw the air from the passenger compartment and pull air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures. The fans operate at two speeds, HI and LO.

The front ventilated seats control buttons panel below the climate controls.

If your vehicle is equipped with a touchscreen, the front ventilated seats control buttons are located within the climate or controls screen of the touchscreen.

• Press the ventilated seat button

Vehicle Equipped With Remote Start

On models that are equipped with remote start, this feature can be programmed to come on during a remote start.

If your vehicle is equipped with a touchscreen, this feature can be programmed through the Uconnect Your Instrument Panel” in the Owner's Manual on the DVD.

If your vehicle is not equipped with a touchscreen, this feature can be programmed through the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” in the Owner's Manual on the DVD.

system. Refer to “Uconnect®Settings” in “Understanding

are located on the center instrument

once to choose HI.

a second time to choose LO.

a third time to turn the ventilated seat OFF.

Front Heated Seats

The front heated seats control buttons are located on the center instrument panel below the climate controls.

If your vehicle is equipped with a touchscreen, the front heated seats control buttons are located within the climate or controls screen of the touchscreen.

• Press the heated seat button

When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after a maximum of 60 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change. The LO-level setting will turn OFF automatically after a maximum of 45 minutes.

once to turn the HI setting On.

a second time to turn the LO setting On.

a third time to turn the heating elements OFF.

Page 35

GETTING STARTED

Vehicle Equipped With Remote Start

On models that are equipped with remote start, this feature can be programmed to come on during a remote start.

If your vehicle is equipped with a touchscreen, this feature can be programmed through the Uconnect Your Instrument Panel” in the Owner's Manual on the DVD.

Rear Heated Seats

The rear heated seat switches are located on the rear of the center console.

• Push the heated seat button

When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after a maximum of 60 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. The LO-level setting will turn OFF automatically after a maximum of 45 minutes.

system. Refer to “Uconnect®Settings” in “Understanding

once to turn the HI setting On.

a second time to turn the LO setting On.

a third time to turn the heating elements OFF.

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

Page 36

GETTING STARTED

HEATED STEERING WHEEL

The steering wheel contains a heating element that heats the steering wheel to one temperature setting.

The heated steering wheel control button panel below the climate controls.

If your vehicle is equipped with a touchscreen, the heated steering wheel control button is located within the climate or controls screen of the touchscreen.

• Press the heated steering wheel button

• Press the heated steering wheel button element Off.

Once the heated steering wheel has been turned on, it will operate for approximately 30 to 80 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.

Vehicle Equipped With Remote Start

On models that are equipped with remote start, this feature can be programmed to come on during a remote start.

If your vehicle is equipped with a touchscreen, this feature can be programmed through the Uconnect Your Instrument Panel” in the Owner's Manual on the DVD.

system. Refer to “Uconnect®Settings” in “Understanding

is located on the center instrument

once to turn the heating element On.

a second time to turn the heating

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.

• Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat.

Page 37

GETTING STARTED

TILT STEERING COLUMN

The tilt lever is located on the steering column below the turn signal lever.

• To tilt the column, simply pull the tilt lever rearward toward you and then move the steering wheel upward or downward as desired.

• Release the tilt lever to lock the steering wheel into position.

ADJUSTABLE PEDALS

Push the switch located on the left side of the steering column forward to move the brake and accelerator pedals away from the driver and push the switch rearward to move the pedals closer to the driver.

NOTE:

The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.

CAUTION!

1 — Adjustable Pedal Switch 2 — Tilt Lever

Tilt Lever Location

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal's path.

WARNING!

• Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have a collision. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.

• Do not adjust the pedals while the vehicle is moving. You could lose control and have a collision. Always adjust the pedals while the vehicle is parked.

Page 38

GETTING STARTED

POWER FOLDING OUTSIDE MIRRORS FOR STANDARD AND TRAILER TOW

If equipped with power folding mirrors, they can be electrically folded rearward and unfolded into the drive position.

The switch for the power folding mirrors is located between the power mirror switches L (left) and R (right). Push the switch once and the mirrors will fold in, push the switch a second time and the mirrors will return to the normal driving position.

If the mirror is manually folded after electrically cycled, a potential extra button push is required to get the mirrors back to the home position. If the mirror does not electrically fold check for ice or dirt build up at the pivot area which can cause excessive drag.

Resetting the Power Folding Outside Mirrors

You may need to reset the power folding mirrors if the following occurs:

• The mirrors are accidentally blocked while folding.

• The mirrors are accidentally manually folded/unfolded.

• The mirrors come out of the unfolded position.

• The mirrors shake and vibrate at normal driving speeds.

To reset the power folding mirrors: Fold and unfold them by pushing the button (this may require multiple button pushes). This resets them to their normal position.

NOTE:

• The power fold mirrors are designed to operate while the vehicle is stationary or traveling at moderate speeds. If you attempt to power fold the mirrors at high speeds they may not fully open or close. You should slow down to a moderate speed and complete the operation.

• When pushing the power fold button 10 or more times in one minute the system shuts down for one minute to protect the motors from over heating.

Power Folding Mirror Switch

Page 39

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.

Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.

While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.

The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. Refer to “Maintaining Your Vehicle,” for the recommended viscosity and quality grades.

NOTE:

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of an engine problem or malfunction.

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.

DIESEL ENGINE BREAK-IN RECOMMENDATIONS

• For 3.0L diesel engine break-in recommendations, refer to Diesel Engine Break-In Recommendations on pg. 178

• For 6.7L Cummins diesel engine break-in recommendations, refer to Diesel Engine Break-In Recommendations on pg. 188

Page 40

OPERATING YOUR VEHICLE

TURN SIGNALS/WIPER/WASHER/HIGH BEAMS LEVER

Turn Signal/Wiper/Washer/High Beam Lever

Turn Signals/Lane Change Assist

Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off.

Wipers

Intermittent, Low And High Operation

• Rotate the end of the lever to the first detent position for one of five intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.

Washer Operation

• Push the end of the lever inward to the second detent and hold for as long as spray is desired.

Mist Feature

• When a single wipe to clear off road mist or spray from a passing vehicle is needed, push the washer knob, located on the end of the multifunction lever, inward to the first detent and release. The wipers will cycle one time and automatically shut off.

High Beams

• Push the lever away from you to activate the high beams.

A high beam symbol will illuminate in the cluster to indicate the high beams are on.

NOTE:

For safe driving, turn off the high beams when oncoming traffic is present to prevent headlight glare and as a courtesy to other motorists.

Page 41

OPERATING YOUR VEHICLE

HEADLIGHT SWITCH

NOTE:

If your vehicle is equipped with illuminated approach lights under the outside mirrors they can be turned off through the instrument cluster or the Uconnect radio. For further information refer to the Owner’s Manual on the DVD.

Automatic Headlights/Parking Lights/Headlights

• Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent

for parking lights and to the second

detent for headlights

• With the parking lights or low beam headlights on, push the headlight switch once for fog lights.

• Rotate the headlight switch to AUTO for Automatic headlights.

• When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.

Headlight Switch

1 — Auto 2 — Rotate Headlight Switch 3 — Push Cargo Light 4 — Rotate Dimmer 5 — Push Fog Light

Automatic High Beams

The Automatic High Beams system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted above the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. This feature is programmable through the Uconnect Settings” in “Understanding Your Instrument Panel” in the Owner's Manual on the DVD for further details.

system. Refer to “Uconnect

Instrument Panel Dimmer

•

Rotate the dimmer control to the extreme left position to fully dim the instrument

panel lights and prevent the interior lights from illuminating when a door is opened.

• Rotate the dimmer control right to increase the brightness of the instrument panel when the parking lights or headlights are on.

• Rotate the dimmer control right to the next detent position to fully brighten the odometer and radio when the parking lights or headlights are on.

Page 42

OPERATING YOUR VEHICLE

• Rotate the dimmer control right to the last detent position to turn on the interior lighting.

• If your vehicle is equipped with a touchscreen, the dimming is programmable through the Uconnect Your Instrument Panel” in the Owner's Manual on the DVD for further details.

Cargo Light

The cargo light is strategically placed lighting that helps illuminate the bed area of the truck. A cargo light symbol will illuminate in the cluster to indicate the light is on.

• Push the button to turn ON/OFF the cargo lighting.

ELECTRONIC SPEED CONTROL

The Electronic Speed Control switches are located on the steering wheel.

system. Refer to “Uconnect®Settings ” in “Understanding

Electronic Speed Control Switches

1 — Push CANCEL 2 — Push ON/OFF 3 — Push Resume/Accel 4 — Push Set/Decel

Cruise ON/OFF

• Push the ON/OFF switch to activate the Speed Control.

The cruise symbol Control is on.

• Push the ON/OFF switch a second time to turn the system off.

will appear on the instrument cluster to indicate the Speed

Page 43

OPERATING YOUR VEHICLE

Set

• With the Speed Control on, push and release the SET/DECEL switch to set a desired speed.

Accel/Decel

To Increase Speed

• When the Electronic Speed Control is set, you can increase speed by pushing the RES + button.

The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “Understanding Your Instrument Panel” in the Owner’s Manual DVD for more information. The speed increment shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

• Pushing the RES + button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph.

• If the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established.

Metric Speed (km/h)

• Pushing the RES + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h.

• If the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established.

To Decrease Speed

• When the Electronic Speed Control is set, you can decrease speed by pushing the SET - button.

The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “Understanding Your Instrument Panel” in the Owner’s Manual DVD for more information. The speed decrement shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h):

U.S. Speed (mph)

• Pushing the SET - button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph.

• If the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established.

Metric Speed (km/h)

• Pushing the SET - button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h.

• If the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established.

Page 44

OPERATING YOUR VEHICLE

Resume

• To resume a previously selected set speed in memory, push the RESUME/ACCEL switch and release.

Cancel

• Push the CANCEL switch or apply the brakes to cancel the set speed and maintain the set speed memory.

• Push the ON/OFF switch to turn the system off and erase the set speed memory.

WARNING!

• Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the Electronic Speed Control system off when you are not using it.

• Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

EIGHT-SPEED AUTOMATIC TRANSMISSION — IF EQUIPPED

Your vehicle may be equipped with a fuel efficient eight-speed transmission. The electronic transmission gear selector is located on the instrument panel. The transmission gear (PRND) is displayed both above the shifter control and in the Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID).

• To select a gear range, simply rotate the shifter control.

NOTE:

You must press the brake pedal to shift the transmission out of PARK or from NEUTRAL into DRIVE or REVERSE.

• To shift past multiple gear ranges at once (such as PARK to DRIVE), simply rotate the switch to the appropriate detent.

• Select the DRIVE range for normal driving.

Rotary Gear Selector

Page 45

OPERATING YOUR VEHICLE

ELECTRONIC RANGE SELECT (ERS) OPERATION

Electronic Range Select (ERS) allows you to limit the highest available transmission gear, and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.

ERS Control On The Shift Lever

• Move the console shift lever left (-) or right (+), or toggle the switch on the column shift lever down (-) or up (+) to select the desired top gear.

• For maximum deceleration (engine braking) move the console shift lever left (-) and hold, or toggle the switch on the column shift lever down (-) and hold. Your vehicle will automatically select the lowest safe gear for optimal engine braking.

• To disable ERS, push and hold the console shift lever to the right (+) or push and hold the column shift lever switch up (+) until “D” is displayed in the odometer.

Switching between ERS and DRIVE mode can be done at any vehicle speed.

Refer to your Owner's Manual on the DVD for further details.

ERS Control Position

Page 46

OPERATING YOUR VEHICLE

ELECTRONIC RANGE SELECT (ERS) OPERATION — EIGHT-SPEED TRANSMISSION

The Electronic Range Select (ERS) shift control allows the driver to limit the highest available gear when the transmission shifter switch is in the DRIVE position

You can switch between DRIVE and ERS mode at any vehicle speed.

•

Tapping the ERS (-) switch (on the

steering wheel) will activate ERS mode.

• Once in ERS mode, tapping the ERS (-) or (+) switch will change the top available gear.

• To exit ERS mode, simply push and hold the ERS (+) switch until “D” is once again displayed in the transmission gear position indicator in the instrument cluster.

ERS Control

1500 AIR SUSPENSION SYSTEM

The air suspension system provides full time load leveling capability along with the benefit of being able to adjust vehicle height by the push of a button.

Automatic height changes will occur based on vehicle speed and the current vehicle height. The indicator lamps and EVIC/DID messages matic changes and user requested changes.

will operate the same for auto-

1500 Air Suspension Controls

1 — Off-Road 1 Indicator 2 — Off-Road 2 Indicator 3 — Up Button 4 — Down Button 5 — Entry/Exit Mode Indicator 6 — Normal Ride Height Indicator

Page 47

OPERATING YOUR VEHICLE

Description

Normal Ride Height (NRH) - This is the standard position of the suspension and is

meant for normal driving.

Off-Road 1 (OR1) (Raises the vehicle approximately 1 in (26 mm) - This position should be the primary position for all off-road driving until Off Road 2 (OR2) is needed. A smoother and more comfortable ride will result. To enter OR1, press the “Up” button once from the NRH position while the vehicle speed is below 35 mph (56 km/h). When in the OR1 position, if the vehicle speed remains between 40 mph (64 km/h) and 50 mph (80 km/h) for greater than 20 seconds or if the vehicle speed exceeds 50 mph (80 km/h), the vehicle will be automatically lowered to NRH. Off-Road 1 may not be available due to vehicle payload, an EVIC/DID message will be displayed when this occurs. Refer to “Electronic Vehicle Information Center (EVIC)/ Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

Off-Road 2 (OR2) (Raises the vehicle approximately 2 in (51 mm) - This position is intended for off-roading use only where maximum ground clearance is required. To enter OR2, press the “Up” button twice from the NRH position or once from the OR1 position while vehicle speed is below 20 mph (32 km/h). While in OR2, if the vehicle speed exceeds 25 mph (40 km/h) the vehicle height will be automatically lowered to OR1. Off-Road 2 may not be available due to vehicle payload, an EVIC/DID message will be displayed when this occurs. Refer to “Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

Aero Mode (Lowers the vehicle approximately .6 in (15 mm) – 1500 Models Only - This position provides improved aerodynamics by lowering the vehicle. The vehicle will automatically enter Aero Mode when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the vehicle speed exceeds 66 mph (106 km/h). The vehicle will return to NRH from Aero Mode if the vehicle speed remains between 30 mph (48 km/h) and 35 mph (56 km/h) for greater than 20 seconds or if the vehicle speed falls below 30 mph (48 km/h).

NOTE:

Automatic Aero Mode may be disabled through vehicle settings in the Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID) when equipped with Uconnect 3.0, or your Uconnect

8.4A, or 8.4AN.

Radio when equipped with UConnect®5.0,

Page 48

OPERATING YOUR VEHICLE

Entry/Exit Mode (Lowers the vehicle approximately 2 in (51 mm) - This position lowers the vehicle for easier passenger entry and exit as well as lowering the rear of the vehicle for easier loading and unloading of cargo. To enter Entry/Exit Mode, press the “Down” button once from the NHR while the vehicle speed is below 33 mph (53 km/h). Once the vehicle speed goes below 15 mph (24 km/h) the vehicle height will begin to lower. If the vehicle speed remains between 15 mph (24 km/h) and 25 mph (40 km/h) for greater than 60 seconds, or the vehicle speed exceeds 25 mph (40 km/h) the Entry/Exit change will be cancelled. To return to Normal Height Mode, press the “Up” button once while in Entry/Exit or drive the vehicle over 15 mph (24 km/h). Entry/Exit mode may not be available due to vehicle payload, an EVIC/DID message will be displayed when this occurs. Refer to "Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)" in "Understanding Your Instrument Panel" in the Owner’s Manual on the DVD for further information.

Refer to your Owner’s Manual on the DVD for further details.

Air Suspension Modes

The Air Suspension system has multiple modes to protect the system in unique situations:

Tire Jack Mode

To assist with changing a spare tire, the air suspension system has a feature which allows the automatic leveling to be disabled. Refer to “Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

NOTE:

This mode is intended to be enabled with engine running.

Transport Mode

To assist with flat bed towing, the air suspension system has a feature which will put the vehicle into Entry/Exit height and disable the automatic load leveling system. Refer to “Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

NOTE:

This mode is intended to be enabled with engine running.

Wheel Alignment Mode

Before performing a wheel alignment this mode must be enabled. Refer to “Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

NOTE:

This mode is intended to be enabled with engine running.

Page 49

OPERATING YOUR VEHICLE

Protection Mode

In order to “protect” the air suspension system, the vehicle will enter Protection Mode when the payload has been exceeded or load leveling cannot be achieved. Refer to “Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID)” in “Understanding Your Instrument Panel” in the Owner’s Manual on the DVD for further information.

NOTE:

This mode is intended to be enabled with engine running.

2500-3500 AIR SUSPENSION SYSTEM

The air suspension system provides full time rear load leveling capability for all loading conditions including towing.

Description

Normal Ride Height (NRH) - This is the

standard position of the suspension and is meant for normal driving.

Trailer Mode (Lowers the vehicle approximately 1 in (25 mm) -

lower the rear suspension and provide load leveling for all loading conditions including towing a trailer. After the “ALT TRAILER HEIGHT” button has been pushed, it will blink continuously until the trailer height has been achieved. The system requires that the ignition be in the ON/RUN position or the engine running with zero vehicle speed for all user requested changes. After the engine is turned off, it may be noticed that the air suspension system operates briefly, this is normal. The system is correcting the position of the vehicle to ensure a proper appearance.

Trailer Decoupling/Unloading - The air suspension system will load level (lower/ exhaust only) for up to 10 minutes after the vehicle is turned off. This allows for easy removal of a trailer and/or load from the back of the truck by maintaining the ride height. After 10 minutes you will need to turn the ignition to the run position for the air suspension to maintain ride height. If the air suspension system is disabled using the settings menu (Tire Jack Mode, Transport Mode or Alignment Mode) the system will remain disabled when the vehicle is turned off. Reactivating the air suspension can be accomplished via the settings menu or driving the vehicle above 5 mph (8 km/h) for Tire Jack Mode or Alignment Mode and 16 mph (26 km/h) for Transport Mode.

NOTE:

While loading, engine must be running for air suspension to maintain the ride height.

Refer to your Owner’s Manual on the DVD for further details.

This position will

Alt Trailer Height Button

Page 50

OPERATING YOUR VEHICLE

Air Suspension Modes

The Air Suspension system has multiple modes to protect the system in unique situations:

Tire Jack Mode

NOTE:

This mode is intended to be enabled with engine running.

Transport Mode

NOTE:

This mode is intended to be enabled with engine running.

Wheel Alignment Mode

NOTE:

This mode is intended to be enabled with engine running.

Protection Mode

NOTE:

This mode is intended to be enabled with engine running.

Page 51

OPERATING YOUR VEHICLE

STOP/START SYSTEM — IF EQUIPPED

The Stop/Start function is developed to save fuel and reduce emissions. The system will stop the engine automatically during a vehicle stop if the required conditions are met. Releasing the brake pedal will automatically re-start the vehicle.

Automatic Mode

The Stop/Start feature is enabled after every normal customer engine start. It will remain in STOP/START NOT READY until you drive forward with a vehicle speed greater than 5 mph (8 km/h). At that time, the system will go into STOP/START READY and if all other conditions are met, can go into an STOP/START AUTO STOP ACTIVE “Autostop” mode.

To Activate The Autostop Mode, The Following Must Occur:

1. The system must be in STOP/START READY state. A STOP/START READY message will be displayed in the Electronic Vehicle Information Center (EVIC)/ Driver Information Display (DID) within the Stop/Start section. Refer to “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)” in “Understanding Your Instrument Panel” for further information.

2. The vehicle must be completely stopped.

3. The transmission Gear Selector must be in DRIVE and the brake pedal depressed.

The engine will shut down, the tachometer will move to the zero position and the stop/start telltale will illuminate indicating you are in an Autostop. While in an Autostop, the Climate Controls system may automatically adjust airflow to maintain cabin comfort. Customer settings will be maintained upon return to an engine running condition.

Possible Reasons The Engine Does Not Autostop

Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. In following situations the engine will not stop:

• Driver’s seat belt is not buckled.

• Driver’s door is not closed.

• Outside temperature is less than 1°F (–17°C) or greater than 104°F (40°C).

• Battery temperature too warm or cold.

• The vehicle is on a steep grade.

• Cabin heating or cooling is in process and an acceptable cabin temperature has

not been achieved.

• HVAC is set to full defrost mode at a high blower speed.

• Engine has not reached normal operating temperature.

• Battery discharged.

• The transmission is not in DRIVE.

• Hood is open.

• Vehicle is in 4LO transfer case mode.

Page 52

OPERATING YOUR VEHICLE

Other factors which can inhibit AutoStop include: fuel level, accelerator pedal input, engine temp too high and steering angle.

It may be possible for the vehicle to be driven several times without the STOP/START system going into a STOP/START READY state under more extreme conditions of the items listed above.

To Start The Engine While In Autostop Mode

While in DRIVE the engine will start when the brake pedal is released or the throttle pedal is depressed. The transmission will automatically reengage upon engine restart. During this transition the brakes will hold the vehicle to avoid undesired vehicle movement.

Conditions that will cause the engine to start automatically while in Autostop mode.

The Engine Will Start Automatically When:

• The transmission selector is moved from DRIVE to REVERSE or NEUTRAL

• To maintain cabin temperature near the HVAC settings

• HVAC is set to full defrost mode

• Autostop time exceeds 5 minutes

• Battery voltage drops too low

• Low brake vacuum (e.g. after several brake pedal applications)

• STOP/START OFF switch is pressed

• 4WD system is put into 4LO mode

• The emissions system requires it

• A STOP/START system error occurs

Conditions that force an automatic shift to PARK while in Autostop mode.

The Engine Will Not Start Automatically and the Transmission will be placed in PARK if:

• The driver door is open and brake pedal released

• The driver door is open and the driver seat belt is unbuckled

• The engine hood has been opened

• A STOP/START system error occurs

The engine may then be restarted by moving the transmission shift selector out of PARK (e.g. to DRIVE) or, in some cases, only by a KEY START. The Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID) will display a SHIFT OUT OF PARK message, or a STOP/START KEY START REQUIRED message, to indicate which action is required. Refer to “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)” in “Understanding Your Instrument Panel” for further information.

Page 53

OPERATING YOUR VEHICLE

To Manually Turn Off The Stop Start System

1. Push the STOP/START Off switch (located on the switch bank). The light on the switch will illuminate.

2. The STOP/START OFF message will appear in Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID). Refer to “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)” in “Understanding Your Instrument Panel” for further information.

3. At the next vehicle stop (after turning off the STOP/START system) the engine will not be stopped.

4. If the STOP/START system is manually turned off, the engine can only be started and stopped by cycling the ignition switch.

5. The STOP/START system will reset itself back to an ON condition every time the key is turned off and back on.

To Manually Turn On The Stop Start System

1. Push the STOP/START Off switch (located on the switch bank).

2. The light on the switch will turn off.

STOP/START OFF Switch

System Malfunction

If there is a malfunction in the STOP/START system, the system will not shut down the engine. A SERVICE STOP/START SYSTEM message will appear in the Electronic Vehicle Information Center (EVIC)/Driver Information Display (DID). Refer to “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)” in “Understanding Your Instrument Panel” for further information.

The system will need to be checked by your authorized dealer.

Page 54

OPERATING YOUR VEHICLE

MANUAL CLIMATE CONT ROLS WITHOUT TOUCHSCREEN

Manual Climate Controls

1 — Rotate Blower Control 2 — Push Air Recirculation Button 3 — Rotate Temperature Control

Air Recirculation /Max A/C

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

• Recirculation is not allowed in defrost.

• Recirculation is allowed in floor mode and defrost/floor (mix modes) for approximately five minutes.

4 — Push A/C Button 5 — Rotate Mode Control 6 — Push Defroster Button

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the defroster.

Page 55

OPERATING YOUR VEHICLE

MANUAL CLIMATE CONT ROLS WITH TOUCHSCREEN

Uconnect® 8.4 Manual Climate Controls

1 — Max A/C Indicator 2 — A/C Button 3 — Air Recirculation Button 4 — Front Defroster Button 5 — Defroster Button

6 — Blower Speed Up Button 7 — Mode Control Buttons 8 — Blower Speed Down Button 9 — OFF Button 10 — Temperature Control Buttons

Page 56

OPERATING YOUR VEHICLE

Climate Control Knobs

1 — A/C Button 2 — Temperature Control Buttons 3 — Front Defroster Button 4 — Defroster Button

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

5 — Rotate Blower Control 6 — OFF Button 7 — Air Recirculation Button

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the defroster.

Page 57

OPERATING YOUR VEHICLE

AUTOMATIC CLIMATE CONT ROLS WITH TOUCHSCREEN

Touchscreen Automatic Climate Controls

1 — MAX A/C Button 2 — A/C Button 3 — Air Recirculation Button 4 — AUTO Button 5 — Front Defroster Button 6 — Defroster Button 7 — Passenger Temperature Up

8 — Passenger Temperature Down 9 — SYNC Button 10 — Blower Control Buttons 11 — Mode Control Button 12 — OFF Button 13 — Driver Temperature Down 14 — Driver Temperature Up

Page 58

OPERATING YOUR VEHICLE

Climate Control Knobs

1 — A/C Button 2 — Driver Temperature Up 3 — OFF Button 4 — Blower Control Knob 5 — Passenger Temperature Up 6 — Front Defroster Button

7 — Defroster Button 8 — Passenger Temperature Down 9 — AUTO Button 10 — Driver Temperature Down 11 — Recirculation Button

Air Conditioning (A/C)

• If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C. The mode and blower will be set at the closest mode and blower position that the system was operating in AUTO.

SYNC Temperature Button

• Press the “SYNC” button on the Uconnect®radio touchscreen to control the driver and passenger temperatures simultaneously. Press the “SYNC” button on the touchscreen a second time to control the temperatures individually.

Page 59

OPERATING YOUR VEHICLE

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the Recirculation button off.

• If the Recirculation button is pushed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically.

Heated Mirrors

The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the defroster.

PARKSENSE® FRONT AND REAR PARK ASSIST

ParkSense®can be enabled and disabled by pushing the ParkSense®switch located below the climate controls, on the switch panel.

The four ParkSense behind the vehicle that is within the sensors field of view. The sensors can detect obstacles from approximately 12 inches (30 cm) up to 79 inches (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.

The six ParkSense front of the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 inches (30 cm) up to 47 inches (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.

When an object is detected within 2 meters behind the rear bumper while the vehicle is in REVERSE, a warning will display in the Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID). In addition a chime will sound (when Sound and Display is selected from the Customer Programmable Features section of the Uconnect rate will change from single 1/2 second tone (for rear only), to slow (for rear only), to fast, to continuous.

Refer to your Owner's Manual on the DVD for further details.

sensors, located in the rear fascia/bumper, monitor the area

sensors, located in the front fascia/bumper, monitor the area in

System screen). As the vehicle moves closer to the object, the chime

Cleaning The ParkSense® Sensors

If “PARKSENSE UNAVAILABLE WIPE REAR SENSORS" or "PARKSENSE UNAVAILABLE WIPE FRONT SENSORS” appears in the “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID),” clean the ParkSense with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.

sensors

Page 60

OPERATING YOUR VEHICLE

PARKVIEW® REAR BACK-UP CAMERA

• You can see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The ParkView will be displayed in the rearview mirror or touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.

• If the rearview mirror or touchscreen display appears foggy, clean the ParkView camera located to the left of the tailgate handle.

WARNING!

Drivers must be careful when backing up; even when using the ParkView Rear Back-Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

POWER SLIDING REAR WINDOW

The switch for the power sliding rear window is located on the overhead console.

• Push the switch right to open the glass and pull the switch left to close the glass.

Rear Back-Up Camera image

Power Sliding Rear Window Switch

Page 61

OPERATING YOUR VEHICLE

POWER SUNROOF

• The power sunroof switch is located on the overhead console.

Opening Sunroof

Express Open

Push the switch rearward and release it within one-half second. The sunroof will fully open and stop automatically.

Manual Open

Push and hold the switch rearward to open the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open position until the switch is pushed again.

Power Sunroof Switch

Venting Sunroof

Push and release the button and the sunroof will open to the vent position.

This is called “Express Vent” and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.

1 — Opening Sunroof 2 — Venting Sunroof 3 — Closing Sunroof

Closing Sunroof

Express Closing

Push the switch forward and release it within one-half second. The sunroof will fully close automatically from any position.

Manual Closing

Push and hold the switch forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially closed position until the switch is pushed again.

Page 62

OPERATING YOUR VEHICLE

Pinch Protection Feature

This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, push the switch forward and release to Express Close.

NOTE:

If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled.

WARNING!

• Do not let children play with the sunroof. Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Do not leave the Key Fob in or near the vehicle, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

• In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be severely injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

• Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

Page 63

OPERATING YOUR VEHICLE

WIND BUFFETING

Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together.

If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.

Page 64

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM

1. Uconnect®Voice Command Button pg. 109

2. Uconnect

3. Steering Wheel Audio Controls (Left) pg. 148

4. Steering Wheel Audio Controls (Right) pg. 148

5. Volume Knob/Audio Mute Button

6. Assist Button pg. 73

Phone Button pg. 109

Page 65

ELECTRONICS

7. 9-1-1 Button pg. 73

8. Uconnect

9. Screen Off Button

10. Back Button

11. Tune/Scroll Knob/Browse/Enter Button

12. Media Hub: Audio Jack, USB Port, and SD Card Slot (located center console) pg. 102

13. CD Player (Inside Center Console — If Equipped) pg. 129

8.4 Radio pg. 96

Page 66

ELECTRONICS

IDENTIFYING YOUR RADIO

Uconnect® 3.0

• Two buttons on the faceplate on either side of the display

Uconnect® 5.0

• 5” Touchscreen

• Three buttons on the faceplate on either side of the display

Uconnect® 3.0

Uconnect® 5.0

Page 67

Uconnect® 8.4A

• 8.4” Touchscreen

• Climate button on the touchscreen in lower menu bar

• HD Button will NOT be visible on right side of screen when viewing AM or FM

SiriusXM Travel Link feature NOT listed

• within Apps

Uconnect® 8.4AN

• 8.4” Touchscreen

• Climate button on the touchscreen in lower menu bar

• HD Button will be visible on right side of screen when viewing AM or FM

• SiriusXM Travel Link feature listed within Apps

ELECTRONICS

Uconnect® 8.4A

Uconnect® 8.4AN

1 — HD Radio — Standard On Uconnect 2 — Navigation — Standard On Uconnect

8.4AN

Page 68

ELECTRONICS

Uconnect® ACCESS

Uconnect® Access — If Equipped (Available On Uconnect®

8.4A/8.4AN — U.S. Residents Only)

WARNING!

ALWAYS drive safely with your hands on the steering wheel. You have full responsibility and assume all risks related to the use of the Uconnect features and applications in this vehicle. Only use Uconnect when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.

Uconnect your vehicle with a built-in cellular connection. With Uconnect

• Place a call to a local 9-1-1 Operator for emergency assistance.

• Remotely lock/unlock your doors and start your vehicle from virtually anywhere, using the Uconnect logging into Mopar Owner Connect, or by calling Uconnect within the United States and have network coverage).

• Turn your vehicle into a WiFi Hotspot and connect your devices to the internet.

• Receive text or email notifications if your vehicle's theft alarm goes off.

• Receive stolen vehicle assistance, using GPS technology to help authorities locate your vehicle if it is stolen.

• Listen to your text messages or send free-form text messages with your voice while keeping your hands on the wheel, using the Voice Texting feature. Requires a cell phone that supports Bluetooth Message Access Profile (MAP).

• Search for places to eat, shop, relax and play with Yelp on-screen menu. Then navigate to them (navigation standard on Uconnect

8.4AN, optional on Uconnect®8.4A).

• Get operator assistance using the ASSIST button on your interior rearview mirror.

Before you drive, familiarize yourself with the easy-to-use Uconnect® Access.

1. The ASSIST and 9-1-1 buttons are located on your rearview mirror. The ASSIST

button is used for contacting Roadside Assistance, Vehicle Care and Uconnect Care. The 9-1-1 button connects you to emergency services.

NOTE: Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls.

2. The Uconnect

radio touchscreen. This is where you can begin your registration process, manage your Apps and purchase WiFi on demand.

Access enhances your ownership and driving experience by connecting

Access App from your smartphone. You can also do so by

“Apps” button on the menu bar at the bottom right corner of the

Access, you can:

Care. (Vehicle must be

, using your voice or

Page 69

ELECTRONICS

3. The Uconnect®Voice Command and Uconnect®Phone buttons are located on the left side of your steering wheel. These buttons let you use your voice to give commands, make phone calls, send and receive text messages hands-free, enter navigation destinations, and control your radio and media devices.

Included Trial Period For New Vehicles

Your new vehicle may come with an included trial period for use of the Uconnect Access Services starting at the date of vehicle purchase (date based on vehicle sales notification from your dealer). To activate the trial, you must first register with Uconnect® Access. After the trial period, if you wish to continue your Uconnect Access Services you can choose to purchase a subscription.

Features And Packages

•

After the trial period, you can subscribe to continue your service by visiting the Uconnect Store located within the Mopar Owner Connect website need assistance, U.S. residents can call Uconnect

•

For the latest information on packages and pricing information: U.S. residents visit DriveUconnect.com.

Uconnect® Access Registration (Uconnect® 8.4A/8.4AN, U.S. 48 Contiguous States, Alaska And Hawaii)

To unlock the full potential of Uconnect®Access in your vehicle, you first need to register with Uconnect

From the parked vehicle with the radio touchscreen powered on, select the “Apps”

1. button located near the bottom right-hand corner of the radio touchscreen.

NOTE:

Should you require assistance anytime during the registration process, simply call Uconnect

Care at 1-855-792-4241 .

2. Press “Start” on the reminder screen or select “Uconnect Registration” under the “All Apps” or “Favorites Apps” tab on the Apps list.

3. The Uconnect instructions to start your registration.

4. Enter your email address into the radio touchscreen.

5. A message will display on the touchscreen indicating your email submission was accepted. In a few minutes, you will receive an email which will allow you to register your vehicle for Uconnect your Uconnect

6. Check for an email from Uconnect registration link. If you don't see it, check your spam or junk mail folder. Open the email and click on the link to continue registering.

Access.

Access Registration App will open and display step-by-step

Access registration within 72 hours.

Access. You should open this email and begin

Access that contains your personalized

moparownerconnect.com. If you

Care at 1-855-792-4241 .

Page 70

ELECTRONICS

NOTE:

For security reasons, this link is valid for 72 hours from the time you’ve submitted your email address into the radio touchscreen. If the link has expired, simply re-enter your email address into the Uconnect to receive another link. The secured registration link will take you through the Uconnect

Access registration process step by step.

7. To unlock the full potential of Uconnect create or validate an existing Mopar Owner Connect account previously (Owner Center). Uconnect

along with Mopar Owner Connect have joined forces to create one destination to manage all of your vehicle needs, from managing your Uconnect

Access account, to tracking service history and finding recommended accessories for your vehicle. If you already have a Mopar Owner Connect account, log in to the website with your existing username/email and password. For assistance with this web based registration process, call Uconnect 1-855-792-4241 .

8. Once you are logged in to your Mopar Owner Connect account, you will create a

personal Uconnect

Security PIN. The Uconnect®Security PIN will be required to authenticate you when accessing your account via Uconnect ing any remote services such as Remote Door Lock/Unlock, Remote Horn & Lights or Starting and Stopping the engine.

9. If your vehicle qualifies for a trial package it will be presented. Simply agree to the Uconnect

button.

At this point your vehicle is registered with Uconnect Mobile. Apps will be downloaded the next time you start your vehicle. If the Apps have not appeared after 24 hours, please contact Uconnect

Registration App on the radio touchscreen

Access in your vehicle, you will need to

Care at

Care or perform-

Access. Continue to set up Via

Care.

Download The Uconnect® Access App

The Uconnect®Access smartphone App allows you to remotely lock or unlock your doors, start your engine (if equipped) and activate your horn and lights from virtually anywhere. The smartphone App also features Via Mobile (if equipped) which uses your smartphone’s data plan to access your personal Pandora Radio and Aha™ by HARMAN accounts and control them using your vehicle touchscreen.

The Uconnect

Access app is only compatible with select iPhone®and Android smartphones. Visit UconnectPhone.com or call 1-877-855-8400 to confirm that your smartphone is compatible with Uconnect phone is compatible, Android and iPhone

. Once you’ve confirmed your smart-

users should visit their respective app

store and search for “Uconnect Access” to download the app.

, iHeartRadio, Slacker

Page 71

ELECTRONICS

Set Up Your Via Mobile Profile — If Equipped

Setting up your Via Mobile profile means entering your login information for each App so that they can work in your vehicle. Complete your Via Mobile Profile online during registration of your Uconnect Mopar Owner Connect account (moparownerconnect.com), going to Edit Profile, then Via Mobile Profile.

If you already have an account with these Apps, scroll down and press the “Link” button to enter your information. If you do not have an account, you can create a new one.

Aha™ by HARMAN (www.aharadio.com)

• Enter your email address and password for Aha™, or create a new Aha™ account.

• You can link your Facebook, Twitter or Slacker accounts on the Aha™ website.

iHeartRadio (www.iHeartRadio.com)

• Enter your email address and password for iHeartRadio, or create a new iHeartRadio account.

• Select “Activate” to continue,

• Select “Close” to complete activation.

Pandora® (www.pandora.com)

• Enter your Pandora

• Create a new Pandora

Slacker Radio (www.slacker.com)

• Enter your Slacker username/email address and password, then click “Save.”

• Create a new Slacker Radio account.

Invite family and friends to use the Via Mobile Apps in your vehicle by setting up their own Via Mobile profile.

Access system. Access this page by logging into your

username/email address and password, then click “Save.”

account.

Renewing Subscriptions And Purchasing WiFi Hotspot (Uconnect® 8.4A/8.4AN, U.S. 48 Contiguous States And Alaska)

Subscriptions, and WiFi Hotspot, can be purchased from the Uconnect®Store within your vehicle, and online at Mopar Owner Connect. If you need help push the ASSIST button on the rearview mirror, then select Uconnect

Purchasing Online

You can renew your subscription to a package or purchase WiFi from the Mopar Owner Connect website. You must first set up a Uconnect Log into moparownerconnect.com

1. Log In to the Mopar Owner Connect website (moparownerconnect.com) with your

username/email and password.

2. Click on the “Shop” tab, then click on the Uconnect

Care (or dial 1-855-792-4241 ).

Access Payment Account online.

Store.

Page 72

ELECTRONICS

3. From the Uconnect®Store, select the item you wish to purchase.

4. This will launch the selected item into purchase mode along with providing additional information.

5. The Uconnect financial details of your purchase. Click the “Purchase” key to continue.

6. The Uconnect payment method on file in your Payment Account. Click the “Complete” key to continue.

7. The Uconnect which you established when setting up your Uconnect entering this four digit PIN, click the “Complete” key to make the purchase.

8. You will receive a confirmation message that your purchase has been submitted. Click the “OK” button to end the process.

Purchasing WiFi Hotspot While In Your Vehicle

You must set up a Uconnect moparownerconnect.com, go to Edit Profile, then Uconnect set up and manage your Payment Account).

1. To purchase WiFi while in your vehicle, ensure the vehicle is running and in Park. Press the “Apps” button on the touchscreen, then select WiFi within the “Apps” menu. Follow the on-screen instructions. When asked for your payment PIN, use the 4-digit PIN you established when setting up your payment account on Mopar Owner Connect.

NOTE:

This may be different than the Uconnect features such as Remote Vehicle Start. After purchasing WiFi, it may take up to 30 minutes (with the vehicle running) before the WiFi will be active in your vehicle.

2. Select WiFi again, then note the hotspot name. Select this network when connecting devices to the hotspot. Also click on View/Edit Passphrase, then note the security passphrase you will need to connect to the network on each device.

If your devices cannot see the WiFi Hotspot network after 30 minutes, please contact Uconnect 1-855-792-4241 .

Store will display a “Purchase Overview” message confirming the

Store will ask you to “Confirm Payment” using your default

Payment Account will then ask for your “Payment Account PIN,”

Access Payment Account online (log in to

Security PIN you established for using

Care by pushing the ASSIST button on the rearview mirror, or by calling

payment account. After

Payment Account, to

Page 73

ELECTRONICS

Using Uconnect® Access

Getting Started With Apps

Applications (Apps) and features in your Uconnect®Access system deliver services that are customized for the driver and are certified by FCA US LLC. Two different types are:

1. Built-In Features — use the built-in 3G Cellular Network on your Uconnect

8.4A/8.4AN radio.

2. Uconnect® Access Via Mobile (if equipped) — Via Mobile uses the Uconnect

Access App and your smartphone's data plan to access your personal Pandora®, iHeartRadio, Aha™ by HARMAN and Slacker Radio accounts from the vehicle and control them using the vehicle touchscreen. Customer’s data plan charges will apply. Available on Uconnect

Get started with your Uconnect button on the menu bar at the bottom right corner of the radio touchscreen. Available apps and features are organized by the tabs on the left of the screen:

Favorite Apps — This is the default screen when you first press the “Apps” button on the touchscreen, and is a good place to put the apps you use most frequently. To make an App a “favorite”, press the “Settings” button on the touchscreen to the right of the app, and select “Make a favorite.”

All Apps — Organizes your Uconnect Running Apps — Press this tab to see which apps are currently running.

8.4A and 8.4AN Radios (if equipped).

Access apps by pressing the Uconnect®“Apps”

Access Apps (when available).

Favorite Apps

1 — Category Tabs 2 — Apps Button

Page 74

ELECTRONICS

Maintaining Your Uconnect® Access Account

Reinstalling An App (Uconnect® 8.4A/8.4AN)

You can easily correct many Application related issues you may be experiencing by resetting the App back to the factory setting. From the vehicle’s radio touchscreen, complete the following steps:

1. Press the Uconnect Apps.

2. In My Apps, select “Settings,” then “Reinstall App.” Press “Continue.”

3. Your Apps have been successfully re-installed.

Canceling Your Subscription

Should you want to cancel your subscription, you can remove your account information using the same procedure contained in the Selling Your Vehicle section.

Selling Your Vehicle

When you sell your vehicle, we recommend that you remove your Uconnect Account information from the vehicle. You can do this using the radio touchscreen in the vehicle or on the Mopar Owner Connect website (moparownerconnect.com). Removing your account information cancels your subscription and makes your vehicle factory-ready for a new owner/subscriber.

1. From your vehicle’s radio touchscreen, select “Uconnect Menu.

2. Select “My Apps,” then “Settings.” Press “Remove Uconnect

3. Enter your Uconnect

For additional information on Uconnect

• U.S. residents - visit DriveUconnect.com or call 1-877-855-8400 .

• Canadian Residents - visit DriveUconnect.ca or call, 1-800-465-2001 (English)

or 1-800-387-9983 (French).

“Apps” button and open the Uconnect®Store. Go to My

Access

Store” from the Apps

Account.”

Security PIN, and select “Continue.”

Page 75

ELECTRONICS

Built-In Features (Uconnect® 8.4AN Only)

CAUTION!

• Ignoring the rearview mirror light could mean you may not have 9-1-1 Call service if needed. If the rearview mirror light is illuminated, have an authorized dealer service the 9-1-1 Call system immediately.

• The Occupant Restraint Controller (ORC) turns on the Air Bag Warning Light on the instrument panel if a malfunction is detected in any part of the air bag system. If the Air Bag Warning Light is illuminated, the air bag system may not be working properly and the 9-1-1 system may not be able to send a signal to a 9-1-1 operator. If the Air Bag Warning Light is illuminated, have an authorized dealer service your vehicle immediately.

• If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location.

• Do not add any aftermarket electrical equipment to the vehicle’s electrical system. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid interference that can cause the 9-1-1 Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.) to your vehicle’s electrical system or modify the antennas on your vehicle. IF YOUR VEHICLE LOSES BATTERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE UCONNECT FEATURES, APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE.

1. Assist Call —

cally connects the vehicle occupants to one of these predefined destinations for immediate support:

• Roadside Assistance Call —Ifyou

get a flat tire, or need a tow, you’ll be connected to someone who can help anytime. Additional fees may apply. Additional information in this section.

• Uconnect® Access Care —Inve-

hicle support for Uconnect System, Apps and Features.

• Vehicle Care — Total support for

your FCA US LLC vehicle.

The rearview mirror contains an ASSIST push button which automati-

Access

ASSIST/9-1-1 Buttons

1 — ASSIST Button 2 — 9-1-1 Button

Page 76

ELECTRONICS

2. Emergency 9-1-1 Call (If Equipped) — The rearview mirror contains a 9-1-1 button

that, when pressed, may place a call from your vehicle to a local 9-1-1 operator to request help from local police, fire or ambulance personnel. If this button is accidentally pressed, you will have 10 seconds to stop the call. To cancel, press the 9-1-1 Call button again or press the “Cancel” button shown on the touchscreen. After 10 seconds has passed, the 9-1-1 call will be placed and only the 9-1-1 operator can cancel it. The LED light on the rearview mirror will turn green once a connection to a 9-1-1 operator has been made. The green LED light will turn off once the 9-1-1 call is terminated. Have an authorized dealer service the vehicle if the rearview mirror light is continuously red. On equipped vehicles, this feature requires a functioning electrical system and wireless coverage to function properly. If a connection is made between a 9-1-1 operator and your vehicle, you

understand and agree that 9-1-1 operators may, like any other 9-1-1 call, record conversations and sounds in and near your vehicle upon connection.

3. Roadside Assistance (If Equipped) — If your vehicle is equipped with this feature

and within wireless range, you may be able to connect to Roadside Assistance by pressing the “ASSIST” button on the rearview mirror. You will be presented with Assist Care options. Make a selection by pressing the prompts displayed on the radio. If Roadside Assistance is provided to your vehicle, you agree to be responsible for any additional roadside assistance service costs that you may incur. In order to provide Uconnect your conversations with Roadside Assistance, Uconnect whether such conversations are initiated through the Uconnect vehicle, or via a landline or mobile telephone, and may share information obtained through such recording and monitoring in accordance with regulatory requirements. You acknowledge, agree and consent to any recording, monitoring or sharing of information obtained through any such call recordings.

4. Yelp® — Customers have the ability to search for nearby destinations or a point

of interest (POI) either by category or custom search by using keywords (for example, “Italian restaurant”). Searching can be done by either voice or by using the touchscreen keypad. Using the touchscreen, launch Yelp “Apps” icon. Press the “All Apps” tab, and then press “Yelp.” To use voice recognition, push the VR button on the steering wheel and say “launch Yelp then follow the instructions on the Teleprompter.

5. Security Alarm Notification — The Security Alarm Notification feature notifies you

via email or text (SMS) message when the vehicle’s factory-installed security alarm system has been set-off. There are a number of reasons why your alarm may have been triggered, one of which could be that your vehicle was stolen. If so, please see the details of the Stolen Vehicle Assistance service below. When you register, Security Alarm Notification is automatically set to send you an email at the mail address you provide should the alarm go off. You may also opt to have a text message sent to your mobile device.

6. Stolen Vehicle Assistance — If your vehicle is stolen, contact local law enforce-

ment immediately to file a stolen vehicle report. Once this report has been filed, Uconnect

care can help locate your vehicle. The Uconnect®Care agent will ask

Services to you, we may record and monitor

Care or Vehicle Care,

Services in your

by selecting the

,”

Page 77

ELECTRONICS

for the stolen vehicle report number issued by local law enforcement. Then, using GPS technology and the built-in wireless connection within your vehicle, the Uconnect enforcement to help recover it. (Vehicle must be within the United States, have network coverage and must be registered with Uconnect subscription that includes the applicable feature).

7. WiFi Hotspot — WiFi Hotspot is on-demand WiFi 3G connectivity that's built-in

and ready to go where ever you are. Once your vehicle is registered for Uconnect Access, you can purchase a Wifi Hotspot subscription at the Uconnect®Store. After you've made your purchase, turn on your signal and connect your passengers devices. It's never been easier to bring your home or office with you.

NOTE:

Your vehicle must have a working electrical system for any of the in vehicle Uconnect

Uconnect® Access Remote Features

If you own a compatible iPhone®or Android®powered device, the Uconnect®Access App allows you to remotely lock or unlock your doors, start your engine or activate your horn and lights from virtually anywhere (Vehicle must be within the United States and have network coverage). You can download the App from Mopar Owner Connect or from the App Store (iPhone) or Google Play store. Visit your device is compatible. For Uconnect if your device is compatible.

U.S. residents - visit UconnectPhone.com or call 1-877-855-8400

Remote Start — This feature provides the ability to start the engine on your vehicle, without the keys and from virtually any distance. You can send a request to your vehicle in one of two ways:

1. Using the Uconnect

2. From the Mopar Owner Connect website.

• After 15 minutes if you have not entered your vehicle with the key, the engine

•

NOTE:

Your four digit Uconnect

• You can set-up notifications for your account to receive an email or text (SMS)

Care agent will be able to locate the stolen vehicle and work with law

Access with an active

features to operate.

UconnectPhone.com to determine if

Phone customer support and to determine

Access App from a compatible smartphone.

will shut off automatically.

You can also send a command to turn-off an engine that has been remote started.

This remote function requires your vehicle to be equipped with a factory-installed Remote Start system. To utilize this feature after the Uconnect

Access App is

downloaded, login with your user name and password.

Security PIN is required to confirm the request.

message every time a command is sent. Login to Mopar Owner Connect (moparownerconnect.com) and click on Edit Profile to manage Uconnect Notifications.

Page 78

ELECTRONICS

Remote Door Lock/Unlock — This feature provides the ability to lock or unlock the door on your vehicle, without the keys and from virtually any distance. You can send a request to your vehicle in one of three ways:

1. Using the Uconnect

2. From the Mopar Owner Connect website.

3. By contacting the Uconnect

To use this feature after the Uconnect user name and password. You will need your four digit Uconnect confirm the request. Press the “closed lock” icon on your Uconnect lock the doors, and press the “open Lock” icon to unlock the driver’s door.

You can set-up notifications for your account to receive an email or text (SMS) message every time a command is sent. Login to Mopar Owner Connect (moparownerconnect.com) and click on Edit Profile to manage Uconnect tions.

Remote Horn And Lights — It’s easy to locate a vehicle in a dark, crowded or noisy parking area by activating the horn and lights. It may also help if you need to draw attention to your vehicle for any reason. You can send a request to your vehicle in one of three ways:

1. Using the Uconnect

2. From the Mopar Owner Connect website.

3. By contacting the Uconnect

To use this feature after the Uconnect user name and password. You will need your four digit Uconnect confirm the request. You can set-up notifications for your account to receive an email or text (SMS) message every time a command is sent. Login to Mopar Owner Connect (moparownerconnect.com) and click on Edit Profile to manage Uconnect tions.

Voice Texting — Want to dictate a personal message? Register with Uconnect Access to take advantage of a new, cloudbased Voice Texting service, an enhancement to Voice Text Reply.

Voice Texting allows you to compose a new text or reply to an incoming text message. Before you attempt to use the Voice Texting feature, check to ensure you have the following:

1. A paired, Bluetooth all Bluetooth Visit UconnectPhone.com for system and device compatibility information.

An active Uconnect®Access trial or paid subscription. Press the “Apps” button on the lower right hand corner of the touchscreen to begin the registration process.

3. Accept the “Allow MAP” profile request on your smart phone. (Please refer to device manufacturer instructions for details).

Access App from a compatible smartphone.

Care on the phone.

Access App is downloaded, login using your

Access App from a compatible smartphone.

Care on the phone.

Access App is downloaded, login using your

enabled phone with the Message Access Profile (MAP). Not

enabled phones support MAP, including all iPhones®(Apple iOS).

Security PIN to

Access App to

Notifica-

Security PIN to

Notifica-

Page 79

ELECTRONICS

To Send A Text Message:

1. Push the Uconnect

Phone Button

2. Wait for the beep.

3. Say “Text.”

4. Uconnect

will prompt you “Say the phone number, or full name and phone type

of the contact you want to send a message to.”

5. Wait for the beep and say a contact that is in your phonebook, or a mobile phone number that you would like to send the message to.

6. Uconnect

will prompt you “Please say the message that you would like to send.” (If you do not hear this prompt, you may not have an active subscription with Uconnect

Access).

7. Wait for the beep, and then dictate any message up to 140 characters. If you exceed 140 characters, you will hear the following prompt: “Message was too long; your message will be truncated.”

8. Uconnect

9. Uconnect

will then repeat the message back to you.

will prompt you: “To add to your message, say “Continue”; To delete the current message and start over, say “Start Over”; to send the current message, say “Send”; to hear the message again, say “Repeat”.

10. If you are happy with your message and would like to send it, wait for the beep and say “Send”.

11. Uconnect

will then say “Sending your message.”

Sample Commands For Voice Text Reply And Voice Texting

Example Command Action

“Text John Smith”

“Text 123 456 7890”

“Show messages”

“Listen to/view (message number four,

“Forward text/message to “John Smith”

for example)”

“Reply”

“Forward text/message to

“123 456 7890”

on the steering wheel.

Send a message to specific contact in

Send 123 456 7890 a message

See recent text messages listed by

Send a voice text reply to a current

Forward current text to specific

address book

from your phonebook

screen

number on Uconnect

Hear messages or read it on

Uconnect

message

contact in address book

phone number

Page 80

ELECTRONICS

Uconnect® Access Via Mobile — If Equipped (Available On Uconnect® 8.4AN)

Via Mobile uses the Uconnect®Access App and your smartphone's data plan to access your personal Pandora accounts from the vehicle and control them using the vehicle touchscreen. Customer’s data plan charges will apply.

To get started using Via Mobile Apps, first register your Uconnect where you'll be guided through the setup of your Via Mobile (requires a compatible Android or iPhone

smartphone). Please refer to “Uconnect®Access Registration”

for more information.

The Uconnect

Access App is compatible with select iPhone®and Android smartphones. Visit UconnectPhone.com to confirm that your smartphone is compatible with Uconnect

. Once you’ve confirmed your smartphone is compatible, pair it to the vehicle touchscreen via Bluetooth USB cable is also supported for the data connection.

Launch the Uconnect®Access App on your smartphone, and login with your username and password that was set up during registration, (this is your login). Accept the Terms and Conditions.

• Ensure that Via Mobile data has been

turned on under “Settings” in the Uconnect

Access App.

• A green indicator next to the words Via

Mobile will show when it is ready to provide data to the radio (a blue indicator when data is being sent). A red indicator means that it is not ready to provide data.

• On android phones, an orange/yellow

indicator signals the phone is connected to the appropriate servers, how-

ever Bluetooth

is turned off on the

mobile phone.

, iHeartRadio, Aha™ by HARMAN and Slacker Radio

Access system

to use Via Mobile apps. If using an iPhone®,a

moparownerconnect.com

Via Mobile Data Enabled

Page 81

ELECTRONICS

Each time you want to use a Via Mobile app in your vehicle, the Uconnect®Access App must be running on your smartphone and the smartphone must be paired via Bluetooth

Data Being Sent

Page 82

ELECTRONICS

If equipped, the Via Mobile apps can be found by selecting the “Apps” button on the touchscreen in the lower right corner of the radio touchscreen. Via Mobile apps are listed under the “All Apps” or “Favorite Apps” tab. The words “Via Mobile” will appear after the app name indicating it is a Via Mobile app.

Favorite Apps

1 — Favorite Tab 2 — Apps Button

Via Mobile apps can also be launched through Voice Recognition by pressing the VR button on the steering wheel and stating “launch” and then the name of the app. For example, you can say “launch Aha Via Mobile.”

NOTE:

For detailed information on how to use Via Mobile apps visit the Mopar Owner Connect website ( set up when registering for Uconnect

moparownerconnect.com) and login using the username and password you

Access.

Page 83

ELECTRONICS

A message will be displayed to remind you that Via Mobile apps utilize the data plan on your connected smartphone to provide content. Many smartphones have a limit to how much data they can utilize before incurring additional charges. The amount of data being used varies by smartphone device, cellular service provider and specific app. Check your mobile phone service plan for more details.* Press “OK” to continue or the “X” to exit.

(*Additional smartphone data usage charges may apply.)

Via Mobile Apps — If Equipped

• Aha™ by HARMAN — Aha™ by HARMAN makes it easy to instantly access your

favorite Web content on the go. Choose from over 40,000+ stations spanning internet radio, personalized music, news, entertainment, hotels, weather, audiobooks, Facebook

• iHeartRadio — iHeartRadio provides instant access to more than 1,500 live radio

stations from across the country and allows listeners to create custom music stations inspired by their favorite artists or songs.

• Pandora® — Pandora

anywhere. Personalized stations launch instantly, with the input of a favorite artist, track, comedian, or genre.

• Slacker Radio — Enjoy millions of songs and hundreds of handcrafted stations.

NOTE:

For detailed information on how to use Via Mobile apps visit the Mopar Owner Connect website ( set up when registering for Uconnect

moparownerconnect.com) and log in using the username and password you

, Twitter®, and more.

gives people the music and comedy they love anytime,

Access.

Page 84

ELECTRONICS

Uconnect® 3.0

1 — RADIO Button 2 — INFO Button 3 — MEDIA Button 4 — A-B-C Button 5 — Preset Buttons 6 — SEEK Down Button 7 — Play/Pause — Mute Button

Uconnect® 3.0 Radio

8 — SEEK Up Button 9 — ON/OFF Button/Volume Knob 10 — BROWSE/ENTER Button/ TUNE/SCROLL Knob 11 — AUDIO Button 12 — MENU Button 13 — BACK Button

Page 85

ELECTRONICS

Clock Setting

1. Press the Menu button at the bottom of the radio, and push the Enter/Browse button for System Settings. Next, select the Time and Format setting and then select Set Time by pushing the Enter/Browse button.

2. Adjust the hours or minutes by turning the Tune/Scroll knob, then pressing the Enter/Browse button to move to the next entry. You can also select 12hr or 24hr format by turning the Tune/Scroll knob, then pressing the Enter/Browse button on the desired selection.

3. Once the time is set press the “Back” button to exit the time screen.

Audio

• Push the AUDIO button on the radio faceplate.

• The Audio Menu shows the following options for you to customize your audio

settings.

Treble, Mid, Bass, Fade, Balance, Speed Adjusted Volume, Loudness and AUX Offset

• Select the desired setting to adjust, then push the ENTER/BROWSE button. Turn

the TUNE/SCROLL knob to adjust the setting + or - . Push the “Back” button when done.

Radio Operation

Seek Up/Down Buttons

• Push the up or down button to seek through radio stations in AM, FM or SXM

bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets Manually

The Presets are available for all Radio Modes, and are activated by pushing any of the six Preset buttons. The Radio stores up to 18 presets in each of the Radio modes. Push the A-B-C button on the faceplate to select the A, B or C preset list.

To store a radio preset manually, follow the steps below:

1. Tune to the desired station.

2. Push and hold the desired numbered button for more than two seconds, or until you hear a confirmation beep.

Page 86

ELECTRONICS

Disc Operation (If Equipped)

Your vehicle may have a remote CD player located in the lower center console storage bin, or in the lower center bench seat bin.

• CD/Disc Mode is entered by either inserting a CD/Disc or by pushing the MEDIA button located on the side of the display. Once in Media Mode, select “Disc.”

Gently insert one CD into the CD player with the CD label facing as indicated on the illustration located on the Disc player.

Seek Up/Down Buttons

• Push to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

USB/Audio Jack (AUX) Manual Operation

To select a specific audio source, push the MEDIA button on the radio faceplate. To allow music to play from your portable device through the vehicle’s speakers, push the “Source” button then select one of the following modes:

USB/iPod®

• USB/iPod into the USB port or by pressing the MEDIA button located left of the display.

Audio Jack (AUX)

• The AUX allows a portable device such as an MP3 player or an iPod into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio cable, to amplify the source and play through the vehicle’s speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. The volume may be controlled using the radio or portable device.

Uconnect® 3.0 Available Media Hubs

Uconnect

3.0

Mode is entered by either inserting a USB Jump Drive or iPod®cable

to be plugged

Media Hub (USB, AUX Ports)

S--OO

Media Hub (SD, USB, AUX Ports)

Remote USB Port (Fully Functional)

Remote USB Port (Charging Only)

Dual Charging Ports

S = Standard Equipment

O = Optional Equipment

Page 87

Uconnect® 5.0

1 — Radio Mode 2 — Compass Information 3 — Media Mode 4 — Access Settings 5 — Uconnect 6 — More Functions

Phone

ELECTRONICS

Uconnect® 5.0

7 — Rotate Volume Control 8 — Rotate Tune/Scroll Knob 9 — Mute Button 10 — Browse/Enter Button 11 — Screen OFF 12 — Back Function

CAUTION!

Do NOT attach any object to the touchscreen, doing so can result in damage to the screen.

Page 88

ELECTRONICS

Clock Setting

To start the clock setting procedure, perform the following:

1. Push the SETTINGS button on the faceplate on the right side of the display, then

press the “Clock & Date” button on the touchscreen.

2. Press the “Set Time & Format” button on the touchscreen.

3. Press the “Up” or “Down” arrows to adjust the hours or minutes, next select the

“AM” or “PM” button on the touchscreen. You can also select 12hr or 24hr format by pressing the desired button on the touchscreen.

4. Once the time is set press the “Done” button on the touchscreen to exit the time

screen.

Equalizer, Balance And Fade

1. Push the SETTINGS button on the faceplate on the right side of the unit.

2. Then scroll down and press the “Audio” button on the touchscreen to get to the

Audio menu.

3. The Audio Menu shows the following options for you to customize your audio

settings.

Equalizer

• Press the “Equalizer” button on the touchscreen to adjust the Bass, Mid and Treble. Use the “+” or “–” button on the touchscreen to adjust the equalizer to your desired settings. Press the “Done” button on the touchscreen when finished.

Balance/Fade

• Press the “Balance/Fade” button on the touchscreen to adjust the sound from the speakers. Use the “arrow” button on the touchscreen to adjust the sound level from the front and rear or right and left side speakers. Press the Center “C” button on the touchscreen to reset the balance and fade to the factory setting. Press the “Done” button on the touchscreen when finished.

Speed Adjustable

• Press the “Speed Adjusted Volume” button on the touchscreen to select between OFF, 1, 2 or 3. This will decrease the radio volume relative to a decrease in vehicle speed. Press the “Done” button on the touchscreen when finished.

Loudness

• Press the “Loudness” button on the touchscreen to select the Loudness feature. When this feature is activated it improves sound quality at lower volumes.

Page 89

ELECTRONICS

Radio Operation

Seek Up/Down Buttons

• Press the up or down button to seek through radio stations in AM, FM or SXM bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets Manually

The Radio stores up to 12 presets in each of the Radio modes. There are four visible presets at the top of the radio screen. Pressing the “All” button on the touchscreen on the radio home screen will display all of the preset stations for that mode.

To store a radio preset manually, follow the steps below:

1. Tune to the desired station

2. Press and hold the desired preset button on the touchscreen for more that two

seconds or until you hear a confirmation beep.

SiriusXM Premier Over 160 channels

Get every channel available on your satellite radio, and enjoy all you want, all in one place. Hear commercial-free music plus sports, news, talk and entertainment. Get all the premium programming, including Howard Stern, every NFL game, Oprah Radio every MLB get 20+ extra channels, including SiriusXM Latino, offering 20 channels of commercial free music, news, talk, comedy, sports and more dedicated to Spanish language programming.

To access SiriusXM Satellite Radio, press the “RADIO” button on the faceplate and then the SXM button on the touchscreen.

SiriusXM services require subscriptions, sold separately after the 12-month trial included with the new vehicle purchase. If you decide to continue your service at the

end of your trial subscription, the plan you choose will automatically renew and bill at then-current rates until you call SiriusXM at 1-866-635-2349 for U.S. residents and 1-888-539-7474 for Canadian residents to cancel. See SiriusXM Customer Agreement for complete terms at www.siriusxm.com for U.S. residents and www.siriusxm.ca for Canadian residents. All fees and programming subject to change. Our satellite service

is available only to those at least 18 and older in the 48 contiguous USA and D.C. Our Sirius satellite service is also available in PR (with coverage limitations). Our Internet radio service is available throughout our satellite service area and in AK and HI. © 2014 Sirius XM Radio Inc. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc.

and NHL®game, every NASCAR®race, Martha Stewart and more. And

Page 90

ELECTRONICS

Disc Operation (If Equipped)

Your vehicle may have a remote CD player located in the lower center console storage bin, or in the lower center bench seat bin.

• CD/Disc Mode is entered by either inserting a CD/Disc or by pressing the MEDIA button located on the side of the display. Once in Media Mode, select “Disc.”

• Gently insert one CD into the CD player with the CD label facing as indicated on the illustration located on the Disc player.

Seek Up/Down Buttons

• Press to seek through Disc tracks.

• Hold either button to bypass tracks without stopping.

Browse

• Press the “Browse” button on the touchscreen to scroll through and select a desired track on the Disc. Press the “Exit” button on the touchscreen if you want to cancel the browse function.

USB/Audio Jack (AUX)/Bluetooth® Manual Operation

USB/iPod®

• USB/iPod into the USB port or by pressing the MEDIA button on the faceplate located left of the display.

Audio Jack (AUX)

• The AUX allows a portable device, such as an MP3 player or an iPod plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio cable, to amplify the source and play through the vehicle speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. The volume may be controlled using the radio or portable device.

Bluetooth®

• If using a Bluetooth your vehicle's sound system.

Uconnect® 5.0 Available Media Hubs

Uconnect

5.0

Mode is entered by either inserting a USB Jump Drive or iPod®cable

- equipped device, you may also be able to stream music to

Media Hub (USB, AUX Ports)

S--SO

Media Hub (SD, USB, AUX Ports)

Remote USB Port (Fully Functional)

Remote USB Port (Charging Only)

Dual Charging Ports

,tobe

S = Standard Equipment

O = Optional Equipment

Page 91

ELECTRONICS

Uconnect® 5.0 VOICE RECOGNITION QUICK TIPS

Introducing Uconnect®

Start using Uconnect®Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect system.

Key Features:

• 5” touchscreen

• Three buttons on either side of the display

5.0

Uconnect® 5.0

Page 92

ELECTRONICS

Get Started

1. U.S. residents can visit UconnectPhone.com to check mobile device and feature

compatibility and to find phone pairing instructions.

2. Reduce background noise. Wind and passenger conversations are examples of

noise that may impact recognition.

3. Speak clearly at a normal pace and volume while facing straight ahead. The

microphone is positioned on the rearview mirror and aimed at the driver.

4. Each time you give a Voice Command, you must first press either the VR or Phone

button, wait until after the beep, then say your Voice Command.

5. You can interrupt the help message or system prompts by pressing the VR or

Phone button and saying a Voice Command from current category.

All you need to control your Uconnect steering wheel.

system with your voice are the buttons on your

Uconnect® VR/Phone Buttons

1 — Push To Begin Radio or Media Functions 2 — Push To Initiate, Answer, Or End A Phone Call, Send Or Receive A Text

Page 93

ELECTRONICS

Basic Voice Commands

The basic Voice Commands below can be given at any point while using your Uconnect system.

Push the VR button . After the beep, say:

• Cancel to stop a current voice session

• Help to hear a list of suggested Voice Commands

• Repeat to listen to the system prompts again

Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen.

Uconnect® 5.0 Visual Cues

Page 94

ELECTRONICS

Radio

Use your voice to quickly get to the AM, FM or SiriusXM™ Satellite Radio®stations you would like to hear. (Subscription or included SiriusXM™ Satellite Radio trial required.)

Push the VR button

• Tune to ninety-five-point-five FM

• Tune to Satellite Channel Hits 1

TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button commands.

. After the beep, say:

and say “Help.” The system will provide you with a list of

Uconnect® 5.0 Radio

Page 95

ELECTRONICS

Media

Uconnect®offers connections via USB, SD, Bluetooth®and auxiliary ports (If Equipped). Voice operation is only available for connected USB and iPod optional and not available on all vehicles.)

Push the VR button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist.

• Change source to Bluetooth

• Change source to iPod

• Change source to USB

• Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play

genre Classical

TIP:

Press the Browse button on the touchscreen to see all of the music on your iPod or USB device. Your Voice Command must match and genre information is displayed.

devices. (Remote CD player

exactly how the artist, album, song

Uconnect® 5.0 Media

Page 96

ELECTRONICS

Phone

Making and answering hands-free phone calls is easy with Uconnect®. When the Phonebook button is illuminated on your touchscreen, your system is ready.

U.S. residents can visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions.

Push the Phone button

• Call John Smith

• Dial 123-456-7890 and follow the system prompts

• Redial (call previous outgoing phone number)

• Call back (call previous incoming phone number)

TIP: When providing a Voice Command, push the Phone button then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.”

. After the beep, say one of the following commands…

and say “Call,”

Uconnect® 5.0 Phone

Page 97

ELECTRONICS

Voice Text Reply

Uconnect will announce incoming text messages. Push the Phone button and say Listen. (Must have compatible mobile phone paired to Uconnect system.)

1. Once an incoming text message is read to you, push the Phone button

the beep, say: Reply.

2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined

messages and follow the system prompts.

TIP: Your mobile phone must have the full implementation of the Message Access Profile (MAP) to take advantage of this feature. For details about MAP, visit

UconnectPhone.com for U.S. residents. Apple iPhone iOS6 or later supports reading

incoming text messages only.

PRE-DEFINED VOICE TEXT REPLY RESPONSES

Yes. Stuck in Traffic. See you later. No. Start without me. I’ll be Late.

Okay. Where are you?

Call me. Are you there yet?

I’ll call you later. I need directions.

I’m on my way.

I’m lost. Thanks.

Can’t talk right now.

I will be <number>

minutes late.

See you in <number>

minutes.

Additional Information

© 2015 FCA US LLC. All rights reserved. Mopar, Mopar Owner Connect and Uconnect are registered trademarks of FCA US LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc. Yelp, Yelp logo, Yelp burst and related marks are registered trademarks of Yelp.

Uconnect®System Support:

• U.S. residents visit DriveUconnect.com or call: 1-877-855-8400

• Canadian residents visit DriveUconnect.ca or call: 1-800-465-2001 (English) or

1-800-387-9983 (French)

Mon. – Fri., 7:00 am – 12:00 am, ET

Sat., 8:00 am – 10:00 pm, ET

Sun., 9:00 am – 5:00 pm, ET

Uconnect Security PIN ready when you call.

Access Services Support. 1-855-792-4241 Please have your Uconnect

. After

Page 98

ELECTRONICS

Uconnect® 8.4A

Uconnect® 8.4A AT A GLANCE

Uconnect® 8.4A Radio Screen

1 — Status Bar 2 — Menu Bar 3 — Uconnect 4 — Uconnect

Displaying The Time

• If the time is not currently displayed on the radio or player main page, press the “settings” button on the touchscreen or the “Apps” button on the touchscreen and then the “settings” button on the touchscreen. In the Settings list, press the “Clock” button on the touchscreen then press the check box next to Show Time in Status Bar.

Apps Button

Phone Button

5 — Climate Button 6 — Controls Button 7 — Media Button 8 — Radio Button

Page 99

ELECTRONICS

Setting The Time

• Turn the unit on, then press the time display at the top of the screen. Press “Yes.”

• If the time is not displayed at the top of the screen, press the “Controls” button on the touchscreen, or the “Apps” button on the touchscreen, and then the “settings” button on the touchscreen. In the Settings screen, press the “Clock” button on the touchscreen, then check or uncheck this option.

• Press “+” or “–” next to Set Time Hours and Set Time Minutes to adjust the time.

• If these features are not available, uncheck the Sync with GPS box.

• Press “X” to save your settings and exit out of the Clock Setting screen.

Audio Settings

• Press the “Audio” button on the touchscreen to activate the Audio settings screen to adjust Balance\Fade, Equalizer, and Speed Adjusted Volume.

• You can return to the Radio screen by pressing the “X” located at the top right.

Balance/Fade

• Press the “Balance/Fade” button on the touchscreen to Balance the audio between the front speakers or fade the audio between the rear and front speakers.

• Pressing the “Front,” “Rear,” “Left,” or “Right” buttons on the touchscreen or press and drag the Speaker Icon to adjust the Balance/Fade.

Equalizer

• Press the “Equalizer” button on the touchscreen to activate the Equalizer screen.

• Press the “+” or “–” buttons on the touchscreen, or by pressing and dragging over the level bar for each of the equalizer bands. The level value, which spans between plus or minus 9, is displayed at the bottom of each of the Bands.

Speed Adjusted Volume

• Press the “Speed Adjusted Volume” button on the touchscreen to activate the Speed Adjusted Volume screen. The Speed Adjusted Volume is adjusted by pressing the volume level indicator. This alters the automatic adjustment of the audio volume with variation to vehicle speed.

Page 100

ELECTRONICS

RADIO

Uconnect® 8.4A Radio Screen

1 — Radio Station Presets 2 — Toggle Between Presets 3 — Audio Settings 4 — Seek Up

5 — Direct Tune To A Radio Station 6 — Seek Down 7 — Browse And Manage Presets 8 — Choose Radio Band

To access the Radio mode, press the “Radio” button on the touchscreen at the lower left of the screen.

Selecting Radio Stations

• Press the desired radio band (AM, FM or SXM) button on the touchscreen.

Seek Up/Seek Down

• Press the Seek up or down arrow buttons on the touchscreen for less than two seconds to seek through radio stations.

• Press and hold either arrow button on the touchscreen for more than two seconds to bypass stations without stopping. The radio will stop at the next listenable station once the arrow button on the touchscreen is released.

Dodge 2015 RAM 1500, 2015 RAM 3500, 2015 RAM 2500 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

INTRODUCTION/WELCOME

WELCOME FROM FCA US LLC

VEHICLES SOLD IN CANADA

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

CONTROLS AT A GLANCE

DRIVER COCKPIT

INSTRUMENT CLUSTER

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors

Panic Alarm

RKE Air Suspension (Remote Lowering Of Vehicle) — If Equipped

Emergency Key

KEYLESS ENTER-N-GO™

To Unlock From The Driver Or Passenger Side:

To Lock The Vehicle’s Doors:

Engine Starting/Stopping

REMOTE START

VEHICLE SECURITY ALARM

To Arm The System:

To Disarm The System:

SEAT BELT SYSTEMS

Lap/Shoulder Belts

Center Lap Belts

Seat Belt Pretensioner

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

Air Bag System Components

Advanced Front Air Bags

Supplemental Side Air Bags

CHILD RESTRAINTS

LATCH — Lower Anchors And Tethers For CHildren (Crew/Quad Cab Full Bench)

LATCH – Lower Anchors And Tethers For CHildren (Crew/Mega/Quad Cab Split Bench)

LATCH System Weight Limit

Locating LATCH Anchorages

Locating Tether Anchorages

Center Seat LATCH (Regular/Quad/Crew Cab Full And Standard Bench)

Center Seat LATCH (Mega/Quad/Crew Cab Split Bench)

Installing The Child Restraint Using The LATCH Lower Anchors

Installing The Child Restraint Using The Vehicle Seat Belts (Regular Cab)

Installing The Child Restraint Using The Vehicle Seat Belts (Mega/Quad/Crew Cab Full And Split Bench)

Tether Anchorage Weight Limit

To Install A Child Seat Using An ALR:

To Install A Child Seat Using A Cinching Latch Plate:

Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt):

Tether Strap Installation

HEAD RESTRAINTS

Front Head Restraints

Rear Head Restraints

FRONT SEATS

Power Seats

Power Lumbar

Memory Seat

Manual Seats

HEATED/VENTILATED SEATS

Front Ventilated Seats

Front Heated Seats

Rear Heated Seats

HEATED STEERING WHEEL

TILT STEERING COLUMN

ADJUSTABLE PEDALS

POWER FOLDING OUTSIDE MIRRORS FOR STANDARD AND TRAILER TOW

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

DIESEL ENGINE BREAK-IN RECOMMENDATIONS

TURN SIGNALS/WIPER/WASHER/HIGH BEAMS LEVER

Turn Signals/Lane Change Assist

Wipers

High Beams

HEADLIGHT SWITCH

Automatic Headlights/Parking Lights/Headlights

Automatic High Beams

Instrument Panel Dimmer

Cargo Light

ELECTRONIC SPEED CONTROL

Cruise ON/OFF