How it Works
DMP
Loading...
XR200
User Manual
55 pgs383.18 Kb0

DMP XR200 User Manual

Download
XR200
User’s Guide
XR200
User’s Guide
Silencing an Alarm All/Perimeter and Home/Away Systems
1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM SILENCE.
3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Area Systems
1. While the alarm bell or siren is sounding, enter your user code. The system silences the alarm bell or siren.
2. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Copyright© 1995 - 1997 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Silencing an Alarm All/Perimeter and Home/Away Systems
1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM SILENCE.
3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Area Systems
1. While the alarm bell or siren is sounding, enter your user code. The system silences the alarm bell or siren.
2. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Copyright© 1995 - 1997 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Security Command User's Guide
for XR200 Command Processor Panels
Table of Contents
About your system
Emergency Evacuation Plans .......................................ii
About Your Security System..........................................1
The Security Command Keypad ...................................2
Special Security Command Displays ............................3
Special Security Command Tones ................................4
Understanding Security System Terms.........................4
General Arming Operation ............................................6
Arming and Disarming
Area System Arming .....................................................7
Area System Disarming ................................................8
All/Perimeter System Arming ........................................9
All/Perimeter System Disarming ..................................10
Home/Away System Arming.........................................11
Home/Away System Disarming....................................12
User Menu
Security Command User Menu ....................................13
Alarm Silence ...............................................................14
Sensor Reset ...............................................................14
Door Access .................................................................15
Armed Areas Display....................................................15
Outputs On Off ............................................................16
Zone Status..................................................................16
Bypass Zones ..............................................................17
Zone Monitor ................................................................18
System Status ..............................................................19
System Test..................................................................19
User Codes ..................................................................20
Schedules ....................................................................23
Setting the Date and Time............................................27
Display Events
Display Events .............................................................28
Arming and Disarming Event Displays.........................29
Zone Event Displays ....................................................29
User Code Change Event Displays..............................30
System Monitor Event Displays ...................................30
Door Access Event Displays ........................................31
Schedule Change Event Displays................................31
Zone Bypass Event Displays .......................................32
Service Request Feature .............................................32
How Your System is Setup
System Setup...............................................................33
Appendix ......................................................................38
Security Command User's Guide
for XR200 Command Processor Panels
Table of Contents
About your system
Emergency Evacuation Plans .......................................ii
About Your Security System..........................................1
The Security Command Keypad ...................................2
Special Security Command Displays ............................3
Special Security Command Tones ................................4
Understanding Security System Terms.........................4
General Arming Operation ............................................6
Arming and Disarming
Area System Arming .....................................................7
Area System Disarming ................................................8
All/Perimeter System Arming ........................................9
All/Perimeter System Disarming ..................................10
Home/Away System Arming.........................................11
Home/Away System Disarming....................................12
User Menu
Security Command User Menu ....................................13
Alarm Silence ...............................................................14
Sensor Reset ...............................................................14
Door Access .................................................................15
Armed Areas Display....................................................15
Outputs On Off ............................................................16
Zone Status..................................................................16
Bypass Zones ..............................................................17
Zone Monitor ................................................................18
System Status ..............................................................19
System Test..................................................................19
User Codes ..................................................................20
Schedules ....................................................................23
Setting the Date and Time............................................27
Display Events
Display Events .............................................................28
Arming and Disarming Event Displays.........................29
Zone Event Displays ....................................................29
User Code Change Event Displays..............................30
System Monitor Event Displays ...................................30
Door Access Event Displays ........................................31
Schedule Change Event Displays................................31
Zone Bypass Event Displays .......................................32
Service Request Feature .............................................32
How Your System is Setup
System Setup...............................................................33
Appendix ......................................................................38
Emergency Evacuation Plans
The National Fire Protection Association recommends that you establish an emergency evacuation plan to safeguard lives in the event of a fire or other emergency. Use the following steps as a guide.
Draw a floorplan of your home or business
On a clean sheet of paper, draw the walls, windows, doors, and stairs. Also draw any obstacles that a person may encounter while exiting the building such as large furniture or appliances.
Develop escape routes
Determine at least two routes the occupants in each room can take to safely escape. One route can be the most obvious such as the door. Another can be through a window that can be easily opened. If the window is high off the ground, an escape ladder should be provided.
Draw arrows on the floorplan to show escape routes from each room.
Decide where to meet
Prearrange a meeting place outside and away from where emergency personnel are likely to be working. A neighbor's house or across the street in the front of the house are good locations. Always perform a head count to make sure all occupants safely exited. NEVER ENTER A BURNING BUILDING. If the head count shows one or more persons missing, give this information immediately to the authorities. Never enter a building to look for someone.
Practice your escape plans
Devising an escape plan is only the beginning, before the plan can be effective everyone should practice the escape routes from each room.
First Floor Second Floor
Fire Escape
Window Ladder
Building Front
Building Back
Early detection
The best way to survive a fire or other emergency is to get out early. The installation of a fire alarm system, with smoke and carbon monoxide detectors in each room, can greatly decrease your risk of loss or injury.
Emergency Evacuation Plans
The National Fire Protection Association recommends that you establish an emergency evacuation plan to safeguard lives in the event of a fire or other emergency. Use the following steps as a guide.
Draw a floorplan of your home or business
On a clean sheet of paper, draw the walls, windows, doors, and stairs. Also draw any obstacles that a person may encounter while exiting the building such as large furniture or appliances.
Develop escape routes
Determine at least two routes the occupants in each room can take to safely escape. One route can be the most obvious such as the door. Another can be through a window that can be easily opened. If the window is high off the ground, an escape ladder should be provided.
Draw arrows on the floorplan to show escape routes from each room.
Decide where to meet
Prearrange a meeting place outside and away from where emergency personnel are likely to be working. A neighbor's house or across the street in the front of the house are good locations. Always perform a head count to make sure all occupants safely exited. NEVER ENTER A BURNING BUILDING. If the head count shows one or more persons missing, give this information immediately to the authorities. Never enter a building to look for someone.
Practice your escape plans
Devising an escape plan is only the beginning, before the plan can be effective everyone should practice the escape routes from each room.
First Floor Second Floor
Fire Escape
Window Ladder
Building Front
Building Back
Early detection
The best way to survive a fire or other emergency is to get out early. The installation of a fire alarm system, with smoke and carbon monoxide detectors in each room, can greatly decrease your risk of loss or injury.
Introduction
About Your Security System
The Security Command system has been designed with your safety and comfort in mind. It uses the latest in computer based technology to create the most advanced, user friendly security, fire, and access control system available.
The Security Command system combines ease of use with a simple to understand Security Command keypad to offer the full range of features requested by today’s security system owners. Security Command can protect both the interior and perimeter of your home or business while you're away or just the perimeter when you're inside.
You can turn portions of your protection on or off at any time by pressing a few keys, or have the system turn on or off automatically, every day, by entering a simple schedule. You can add, delete, and change personal user codes at any time or check the status of protection devices in the system.
Parts of the System
There are two main parts to the Security Command system, the Security Command keypad and the keypad User Menu.
Security Command keypad
This is the device we've placed at certain locations throughout the premises that allow you to turn the system’s protection on and off using your personal user code.
A Note About False Alarms
One of the most important concerns facing the security industry today is false alarms. The accidental dispatching of police and fire agencies places others in jeopardy by limiting the response capability of those emergency service units. We take this concern seriously and have spent many hours training our employees to recognize the causes of false alarms and prevent them from occurring.
As part of our commitment to reducing false alarms, we’d like to encourage you to read this guide thoroughly. All the information contained here can help you quickly, and comfortably, learn the operation of the Security Command system. If you have any additional questions, or feel that you need more training, please don’t hesitate to contact us.
Test Your System Weekly
It is recommended that you test the burglary portion of your system at least once each week. Testing should involve an active test of all doors, windows, and motion detectors connected to your system. If your system also has fire protection, call the service department to find out how this portion of your system should be tested.
Refer to the System Test section of this guide for instructions on testing the burglary portion of your system.
Keypad User Menu
The keypad also provides a simple User Menu containing all of the functions you need to fully operate your system such as changing the time of day or a personal user code.
Introduction
About Your Security System
The Security Command system has been designed with your safety and comfort in mind. It uses the latest in computer based technology to create the most advanced, user friendly security, fire, and access control system available.
The Security Command system combines ease of use with a simple to understand Security Command keypad to offer the full range of features requested by today’s security system owners. Security Command can protect both the interior and perimeter of your home or business while you're away or just the perimeter when you're inside.
You can turn portions of your protection on or off at any time by pressing a few keys, or have the system turn on or off automatically, every day, by entering a simple schedule. You can add, delete, and change personal user codes at any time or check the status of protection devices in the system.
Parts of the System
There are two main parts to the Security Command system, the Security Command keypad and the keypad User Menu.
Security Command keypad
This is the device we've placed at certain locations throughout the premises that allow you to turn the system’s protection on and off using your personal user code.
Introduction
1
A Note About False Alarms
One of the most important concerns facing the security industry today is false alarms. The accidental dispatching of police and fire agencies places others in jeopardy by limiting the response capability of those emergency service units. We take this concern seriously and have spent many hours training our employees to recognize the causes of false alarms and prevent them from occurring.
As part of our commitment to reducing false alarms, we’d like to encourage you to read this guide thoroughly. All the information contained here can help you quickly, and comfortably, learn the operation of the Security Command system. If you have any additional questions, or feel that you need more training, please don’t hesitate to contact us.
Test Your System Weekly
It is recommended that you test the burglary portion of your system at least once each week. Testing should involve an active test of all doors, windows, and motion detectors connected to your system. If your system also has fire protection, call the service department to find out how this portion of your system should be tested.
Refer to the System Test section of this guide for instructions on testing the burglary portion of your system.
Keypad User Menu
The keypad also provides a simple User Menu containing all of the functions you need to fully operate your system such as changing the time of day or a personal user code.
Introduction
1
The Security Command Keypad
Your system may have one or more easy to use Security Command keypads (16 or 32 character) that allow you to properly operate the system. The illustration and descriptions below highlight some of the keypad features:
32-Character Keypad
AC
LED
The SELECT keys
There are four keys under the display called the SELECT keys. These keys are one of the features that make your system so easy to operate. They allow you to choose what to do by pressing the SELECT key under choices being shown in the display.
22Introduction
POWER
JONES RESIDENCE FR I 2: 51 AM
1234
A BC
D E F
5678
90
YZ
16-Character Keypad
1234
A B C
567
90
YZ
GHI JKL
DEF
8
VWX
STUPQRMNO
COMMAND
G H I JK L
COMMAND
Lighted display SELECT keys Data Entry keys
VW XMNO P Q R STU
COMMAND key ARROW key
Lighted display SELECT keys AC LED
POWER
Data Entry keys COMMAND key ARROW key
Data Entry keys
These keys allow you to enter your user code when arming or disarming or enter other information into the system.
The ARROW key
The ARROW key is used to go back through the keypad displays while operating your system. You can press the ARROW key to back up through the list of functions in the User Menu or to make a correction by erasing the last character you entered.
The COMMAND key
The COMMAND key allows you to advance through the keypad displays or User Menu or complete a data entry function.
AC LED
This LED remains on steady as long as your system is connected to its AC power supply. Should there be an interruption, the LED turns off and the system's backup battery maintains normal operation for a time allowing you to contact our service department.
32-Character Keypad User Options Menu
Press and hold the ARROW and COMMAND keys for about two seconds. The keypad display shows SET BRIGHTNESS. Use the left SELECT key to lower the display brightness. Use the right SELECT key to increase the display brightness. Press COMMAND.
At SET TONE, use the left SELECT key to lower the keypad tone. Use the right SELECT key to raise the keypad tone. Press COMMAND.
At SET VOLUME LEVEL , use the left SELECT key to lower the keypad volume. Use the right SELECT key to raise the keypad volume. Press COMMAND.
At MODEL NUMBER, the model number of the keypad is displayed. Press the ARROW key to exit out of the User Options menu.
The Security Command Keypad
Your system may have one or more easy to use Security Command keypads (16 or 32 character) that allow you to properly operate the system. The illustration and descriptions below highlight some of the keypad features:
32-Character Keypad
AC
LED
The SELECT keys
There are four keys under the display called the SELECT keys. These keys are one of the features that make your system so easy to operate. They allow you to choose what to do by pressing the SELECT key under choices being shown in the display.
Introduction
POWER
JONES RESIDENCE FR I 2: 51 AM
1234
A BC
D E F
5678
90
YZ
16-Character Keypad
1234
A B C
567
90
YZ
GHI JKL
DEF
8
VWX
STUPQRMNO
COMMAND
G H I JK L
COMMAND
Lighted display SELECT keys Data Entry keys
VW XMNO P Q R STU
COMMAND key ARROW key
Lighted display SELECT keys AC LED
POWER
Data Entry keys COMMAND key ARROW key
Data Entry keys
These keys allow you to enter your user code when arming or disarming or enter other information into the system.
The ARROW key
The ARROW key is used to go back through the keypad displays while operating your system. You can press the ARROW key to back up through the list of functions in the User Menu or to make a correction by erasing the last character you entered.
The COMMAND key
The COMMAND key allows you to advance through the keypad displays or User Menu or complete a data entry function.
AC LED
This LED remains on steady as long as your system is connected to its AC power supply. Should there be an interruption, the LED turns off and the system's backup battery maintains normal operation for a time allowing you to contact our service department.
32-Character Keypad User Options Menu
Press and hold the ARROW and COMMAND keys for about two seconds. The keypad display shows SET BRIGHTNESS. Use the left SELECT key to lower the display brightness. Use the right SELECT key to increase the display brightness. Press COMMAND.
At SET TONE, use the left SELECT key to lower the keypad tone. Use the right SELECT key to raise the keypad tone. Press COMMAND.
At SET VOLUME LEVEL , use the left SELECT key to lower the keypad volume. Use the right SELECT key to raise the keypad volume. Press COMAND.
At MODEL NUMBER, the model number of the keypad is displayed. Press the ARROW key to exit out of the User Options menu.
Special Security Command Displays
As you use your system, you’ll occasionally see a keypad display that asks you to enter a code or that describes a condition on the system. Below are some examples of the displays you'll see:
INVALID TIME
A level 1 or 2 user code has been entered outside of the valid schedule. See Schedules and User Codes.
ALARM
A 24 hour zone (for example fire or panic) or an armed burglary zone has been tripped. Your system may sound bells or sirens.
TROUBLE
There is a problem with a protection device or system component. This display is accompanied by a description of the problem.
ENTER CODE
The system requires you to enter your user code. User codes can be required for turning your system on (arming), turning your system off (disarming), and many other functions.
As you enter your user code, the keypad display shows an asterisk (*) in place of each digit pressed. This keeps others from seeing your user code on the display as it’s entered.
TRY AGAIN or INVALID CODE
The user code you've entered is not recognized by the system. Check the user code and try again.
INVALID LEVEL
All user codes have authority levels that allow the user to only access certain functions. When a user attempts a function outside their authority, the INVALID LEVEL message displays.
SYSTEM TROUBLE or SERVICE REQUIRED
There is a problem with one or more of the components in your system. Contact our service department as soon as possible.
SYSTEM BUSY
The Security Command system is performing another task of a higher priority. This usually only takes a few moments.
Special Wireless Displays
Your system may use radio transmitters to send alarm and trouble information from the protection devices to the panel. Wireless systems operate the same as hardwired and also have a few unique keypad displays.
BACK DOOR - LOBAT – (Low Battery) The battery in a radio transmitter is low. (BACK DOOR is used as an example only.)
BACK DOOR - MISNG - (Missing) The panel is not receiving the radio transmitter's periodic test report.
WIRELESS - TRBL - (Trouble) Some part of your wireless system is operating improperly. Test the system to locate the trouble.
Special Security Command Displays
As you use your system, you’ll occasionally see a keypad display that asks you to enter a code or that describes a condition on the system. Below are some examples of the displays you'll see:
ALARM
A 24 hour zone (for example fire or panic) or an armed burglary zone has been tripped. Your system may sound bells or sirens.
TROUBLE
There is a problem with a protection device or system component. This display is accompanied by a description of the problem.
ENTER CODE
The system requires you to enter your user code. User codes can be required for turning your system on (arming), turning your system off (disarming), and many other functions.
As you enter your user code, the keypad display shows an asterisk (*) in place of each digit pressed. This keeps others from seeing your user code on the display as it’s entered.
TRY AGAIN or INVALID CODE
The user code you've entered is not recognized by the system. Check the user code and try again.
INVALID LEVEL
All user codes have authority levels that allow the user to only access certain functions. When a user attempts a function outside their authority, the INVALID LEVEL message displays.
Introduction
3
INVALID TIME
A level 1 or 2 user code has been entered outside of the valid schedule. See Schedules and User Codes.
SYSTEM TROUBLE or SERVICE REQUIRED
There is a problem with one or more of the components in your system. Contact our service department as soon as possible.
SYSTEM BUSY
The Security Command system is performing another task of a higher priority. This usually only takes a few moments.
Special Wireless Displays
Your system may use radio transmitters to send alarm and trouble information from the protection devices to the panel. Wireless systems operate the same as hardwired and also have a few unique keypad displays.
BACK DOOR - LOBAT – (Low Battery) The battery in a radio transmitter is low. (BACK DOOR is used as an example only.)
BACK DOOR - MISNG - (Missing) The panel is not receiving the radio transmitter's periodic test report.
WIRELESS - TRBL - (Trouble) Some part of your wireless system is operating improperly. Test the system to locate the trouble.
Introduction
3
Special Security Command Tones
Your keypad also contains a small speaker that allows it to alert you to events as they occur on your system. Below are brief descriptions of the different tones you'll hear from the keypad:
Fire Alarm tone: An intermittent sweeping siren that sounds until the fire alarm is silenced, on LCD keypads only.
Understanding Security System Terms
Throughout this guide, and in some displays on your keypad, you’ll see certain words or phrases that might be unfamiliar. Although every effort has been made to use terms that are commonly known, there are some for which there was no acceptable substitute.
Below are some terms you’ll see here and on your keypad display:
Burglary Alarm tone: A constant siren tone at maximum volume that continues until the alarm is silenced, on LCD keypads only.
Key press tone: A short beep each time you press a key on the keypad and it’s acknowledged by the system.
Prewarn tone: A continuous pulsed tone that sounds when you open an entry delay door on a system that is armed (turned on) reminding you to disarm the burglary protection.
Monitor tone: A pulsed tone for one second, one pulse only that sounds whenever a door or window is opened while you’re using the zone monitor function from the User Menu. LCD keypads sound a door bell chime. See Zone Monitor.
Trouble tone: A steady tone indicating a trouble condition on your system. Press a SELECT key to silence.
What to do when the trouble tone is sounding
You can silence the trouble tone by pressing any one of the top row SELECT keys. This only silences the keypad and does not correct the condition that originally caused the trouble.
Introduction
4
Arming
This is the term used for turning on the burglary protection in one or more areas of the system. Your system may require you to enter a user code. When armed, the system is able to sound alarm bells or sirens and, if monitored, send alarm reports to a central station when a burglary zone is tripped.
Fire, panic, and other 24 hour devices are always turned on and do not need to be armed.
Disarming
This means turning off one or more areas of the system. When disarmed, the system does NOT sound alarms or send alarm reports to a central station when a burglary zone is faulted.
Zone
A zone refers to one or more protected openings (doors or windows) or protection devices (motion or glassbreak detectors) grouped together under the same zone name and number.
Often, similar devices in the same general area will share the same zone. For example, the windows on the east side of the premises can all be grouped together in a zone named E. WINDOWS.
Special Security Command Tones
Your keypad also contains a small speaker that allows it to alert you to events as they occur on your system. Below are brief descriptions of the different tones you'll hear from the keypad:
Fire Alarm tone: An intermittent sweeping siren that sounds until the fire alarm is silenced, on LCD keypads only.
Burglary Alarm tone: A constant siren tone at maximum volume that continues until the alarm is silenced, on LCD keypads only.
Key press tone: A short beep each time you press a key on the keypad and it’s acknowledged by the system.
Prewarn tone: A continuous pulsed tone that sounds when you open an entry delay door on a system that is armed (turned on) reminding you to disarm the burglary protection.
Monitor tone: A pulsed tone for one second, one pulse only that sounds whenever a door or window is opened while you’re using the zone monitor function from the User Menu. LCD keypads sound a door bell chime. See Zone Monitor.
Trouble tone: A steady tone indicating a trouble condition on your system. Press a SELECT key to silence.
What to do when the trouble tone is sounding
You can silence the trouble tone by pressing any one of the top row SELECT keys. This only silences the keypad and does not correct the condition that originally caused the trouble.
Understanding Security System Terms
Throughout this guide, and in some displays on your keypad, you’ll see certain words or phrases that might be unfamiliar. Although every effort has been made to use terms that are commonly known, there are some for which there was no acceptable substitute.
Below are some terms you’ll see here and on your keypad display:
Arming
This is the term used for turning on the burglary protection in one or more areas of the system. Your system may require you to enter a user code. When armed, the system is able to sound alarm bells or sirens and, if monitored, send alarm reports to a central station when a burglary zone is tripped.
Fire, panic, and other 24 hour devices are always turned on and do not need to be armed.
Disarming
This means turning off one or more areas of the system. When disarmed, the system does NOT sound alarms or send alarm reports to a central station when a burglary zone is faulted.
Zone
A zone refers to one or more protected openings (doors or windows) or protection devices (motion or glassbreak detectors) grouped together under the same zone name and number.
Often, similar devices in the same general area will share the same zone. For example, the windows on the east side of the premises can all be grouped together in a zone named E. WINDOWS.
Introduction
4
Understanding Security System Terms
Entry or Exit zone
Almost all systems have one or more doors through which you can enter or exit the premises. These doors are programmed with a delay time to allow you to enter or exit without setting off the alarm.
When you arm the system, activity on this zone is ignored until the programmed exit the system is fully armed, opening the door causes the panel to start the
entry
valid user code to disarm the system or an alarm will occur.
Instant Zone
Exterior windows and non entry doors, or interior protection devices, are typically not programmed with delay times. If these zones are tripped while the system is armed, an alarm occurs instantly.
24 Hour Zone
A 24 hour zone is not turned on or off by arming or disarming your system. Some examples of 24 hour zones are: fire zones, panic zones, and temperature control zones.
Areas
An area is made up of burglary zones that can be armed or disarmed together. One area might consist of the office doors and windows. When you arm the office, these zones arm together and sound an alarm if opened.
Central Station Monitoring
Your system can also be programmed to automatically send alarm, trouble, and arming and disarming reports to a central station. Operators at the central station can in turn dispatch the appropriate authorities or contact you with the specific event information.
delay time expires. Once that time has expired and
delay time. During the entry delay time, you must enter a
Status
Status is a feature that automatically displays the armed or disarmed status of your system on the Security Command keypads. Alarm or trouble conditions on a zone or a system monitor such as AC or battery trouble can also be displayed. There are two types of status information available: Armed Status and Status List.
Armed Status
With Armed Status, the keypad displays the current armed condition of areas within your security system. For example:
When you arm areas 1 to 4, the keypad shows = 1234 When you arm areas 1 and 3, the keypad shows = 13
If your system is setup as an All/Perimeter or Home/Away system and both the interior and perimeter is armed the display reads:
ALL SYSTEM ON
Status List
The keypad Status List displays any alarm or trouble condition on a zone, and any trouble condition on an internal system monitor. The system monitors include the AC power, battery power, panel box tamper, printer, and phone lines. If more than one alarm or trouble condition occurs at the same time, the keypad sequences this information on its display.
If the alarm is from a 24 hour zone or a system monitor, it remains in the Status List until it restores. If one or more armed burglary zones trip at the same time, the last one to trip remains in the Status List. This is to ensure that if a burglary has occurred the last zone tripped remains displayed even if it has been restored.
Introduction
5
Understanding Security System Terms
Entry or Exit zone
Almost all systems have one or more doors through which you can enter or exit the premises. These doors are programmed with a delay time to allow you to enter or exit without setting off the alarm.
When you arm the system, activity on this zone is ignored until the programmed exit delay time expires. Once that time has expired and the system is fully armed, opening the door causes the panel to start the
entry
delay time. During the entry delay time, you must enter a
valid user code to disarm the system or an alarm will occur.
Instant Zone
Exterior windows and non entry doors, or interior protection devices, are typically not programmed with delay times. If these zones are tripped while the system is armed, an alarm occurs instantly.
24 Hour Zone
A 24 hour zone is not turned on or off by arming or disarming your system. Some examples of 24 hour zones are: fire zones, panic zones, and temperature control zones.
Areas
An area is made up of burglary zones that can be armed or disarmed together. One area might consist of the office doors and windows. When you arm the office, these zones arm together and sound an alarm if opened.
Central Station Monitoring
Your system can also be programmed to automatically send alarm, trouble, and arming and disarming reports to a central station. Operators at the central station can in turn dispatch the appropriate authorities or contact you with the specific event information.
Status
Status is a feature that automatically displays the armed or disarmed status of your system on the Security Command keypads. Alarm or trouble conditions on a zone or a system monitor such as AC or battery trouble can also be displayed. There are two types of status information available: Armed Status and Status List.
Armed Status
With Armed Status, the keypad displays the current armed condition of areas within your security system. For example:
When you arm areas 1 to 4, the keypad shows = 1234 When you arm areas 1 and 3, the keypad shows = 13
If your system is setup as an All/Perimeter or Home/Away system and both the interior and perimeter is armed the display reads:
ALL SYSTEM ON
Status List
The keypad Status List displays any alarm or trouble condition on a zone, and any trouble condition on an internal system monitor. The system monitors include the AC power, battery power, panel box tamper, printer, and phone lines. If more than one alarm or trouble condition occurs at the same time, the keypad sequences this information on its display.
If the alarm is from a 24 hour zone or a system monitor, it remains in the Status List until it restores. If one or more armed burglary zones trip at the same time, the last one to trip remains in the Status List. This is to ensure that if a burglary has occurred the last zone tripped remains displayed even if it has been restored.
Introduction
5
General Arming Operation
Your system has been programmed to operate in one of three modes: Area Arming, All/Perimeter, or Home/Away.
• Area Arming - Your burglary protection is divided into areas. Each area has a custom name, can be turned on or off independent of other areas, and can have different schedules and authorized users.
• All/Perimeter - Your burglary protection is divided into two areas, Interior and Perimeter. You can turn on the just the Perimeter protection while inside for security or turn on both as you leave.
• Home/Away - Perimeter, Interior, and a Bedrooms area you can leave turned off at night while you're sleeping.
Regardless of how your system has been programmed, much of the operation is similar. Throughout this guide, any differences between the systems are noted for your convenience.
Arming Functions
After making your arming selection, the keypad displays any zones that are currently bypassed. These zones remain bypassed until the system is armed and then disarmed. Any 24 hour zones in a bad condition are also displayed.
Before arming, the system verifies that all doors, windows, and other protection devices to be armed are in a normal condition. If everything is okay, the system arms. If there is a problem on one or more burglary zones the system cannot arm until the problem is corrected. If the problem is simply an open door or window, correct the problem and try arming again.
6
Introduction
If the problem cannot be corrected, you can force arm or bypass the zone or wait until the zone can be repaired by a service technician. A force armed zone is ignored by the system until it restores to normal. A bypassed zone is ignored by the system during the entire armed period. A zone remains bypassed until the system is disarmed.
In some cases, you might see the keypad display FRONT DOOR BAD *. The asterisk next to BAD means that the zone is a priority zone, which cannot be bypassed. The problem on the zone must be corrected before the system can be armed.
Armed Message: After all bypassing is completed or zone faults corrected, the keypad briefly displays ALL SYSTEM ON if all areas in the system are arming and SYSTEM ON if only selected areas are arming. The keypad then displays the exit delay time as it counts down. When the exit delay time expires, all disarmed zones are armed.
If your system uses a keyswitch to arm an area, the exit delay time is NOT shown on the keypad display.
ONE MOMENT . . . Message: If your system is monitored, it may be programmed to wait for the transmission of an arming report to the central station before displaying the armed message. See Arming Report below. This is to verify your phone lines are working properly. While the system is waiting for the transmission, the display reads
ONE MOMENT.... If the report is received, the keypad displays the
armed message. If the report is not received, the keypad displays
LOCAL ALARM ONLY before displaying the armed message. Arming Report: Your system can be programmed to send arming
or zone bypassing reports to a central station. This feature is optional and can be programmed for you at any time.
General Arming Operation
Your system has been programmed to operate in one of three modes: Area Arming, All/Perimeter, or Home/Away.
• Area Arming - Your burglary protection is divided into areas. Each area has a custom name, can be turned on or off independent of other areas, and can have different schedules and authorized users.
• All/Perimeter - Your burglary protection is divided into two areas, Interior and Perimeter. You can turn on the just the Perimeter protection while inside for security or turn on both as you leave.
• Home/Away - Perimeter, Interior, and a Bedrooms area you can leave turned off at night while you're sleeping.
Regardless of how your system has been programmed, much of the operation is similar. Throughout this guide, any differences between the systems are noted for your convenience.
Arming Functions
After making your arming selection, the keypad displays any zones that are currently bypassed. These zones remain bypassed until the system is armed and then disarmed. Any 24 hour zones in a bad condition are also displayed.
Before arming, the system verifies that all doors, windows, and other protection devices to be armed are in a normal condition. If everything is okay, the system arms. If there is a problem on one or more burglary zones the system cannot arm until the problem is corrected. If the problem is simply an open door or window, correct the problem and try arming again.
Introduction
6
If the problem cannot be corrected, you can force arm or bypass the zone or wait until the zone can be repaired by a service technician. A force armed zone is ignored by the system until it restores to normal. A bypassed zone is ignored by the system during the entire armed period. A zone remains bypassed until the system is disarmed.
In some cases, you might see the keypad display FRONT DOOR BAD *. The asterisk next to BAD means that the zone is a priority zone, which cannot be bypassed. The problem on the zone must be corrected before the system can be armed.
Armed Message: After all bypassing is completed or zone faults corrected, the keypad briefly displays ALL SYSTEM ON if all areas in the system are arming and SYSTEM ON if only selected areas are arming. The keypad then displays the exit delay time as it counts down. When the exit delay time expires, all disarmed zones are armed.
If your system uses a keyswitch to arm an area, the exit delay time is NOT shown on the keypad display.
ONE MOMENT . . . Message: If your system is monitored, it may be programmed to wait for the transmission of an arming report to the central station before displaying the armed message. See Arming Report below. This is to verify your phone lines are working properly. While the system is waiting for the transmission, the display reads
ONE MOMENT.... If the report is received, the keypad displays the
armed message. If the report is not received, the keypad displays
LOCAL ALARM ONLY before displaying the armed message. Arming Report: Your system can be programmed to send arming
or zone bypassing reports to a central station. This feature is optional and can be programmed for you at any time.
Area System Arming
Area Assignment: Your security system has been set up into
separate areas. The number of areas and their names are listed in the back of this guide.
Arming or Disarming: You can arm and disarm all areas at one time or each area individually. You can only arm or disarm areas authorized for your user code.
Arm all or Selective Arming: After entering your user code, the system allows you to arm either all of the areas to which you have access or one or more selected areas. If you choose to arm all areas, the system begins verifying that all zones in those areas are in a good condition. If you choose to arm selected areas, the system prompts you to choose the areas you want to arm.
Arming the System:
1. Press the COMMAND key until ARM DISARM is displayed.
2. Select ARM to arm the system.
3. Enter your user code if required. The display reads ALL? NO YES.
4. Select NO to arm only selected areas. Go to step 5. Select YES to arm all areas authorized for your user code. Go to step 6.
5. If you selected NO in step 4, the display begins to list each area to which you have access followed by NO YES.
Example: OFFICE NO YES 5a. Select YES for each area you want to arm. 5b. Select NO for each area you do not want to arm.
Note: You can also just press the area numbers you want to arm
while at the ALL? NO YES display. This changes the display to AREAS: . The area numbers you select appear in the display. For example: AREAS: 2 4 . Press COMMAND when done.
6. The system displays any bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
7. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 7a through 7d.
7a. If a problem exists on a zone, the zone name and problem
is shown followed by: OKAY BYPASS STOP. 7b. Select OKAY to force arm the bad zone. 7c. Select BYPASS to bypass all bad zones being displayed. 7d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
8. The display reads SYSTEM ON if at least one area in the system is armed, and ALL SYSTEM ON if all areas in the system are armed.
9. The keypad then displays the exit time in seconds and counts down the remaining time: EXIT : ## (## = seconds remaining) The exit zones arm when the delay time expires.
Arming and Disarming
7
Area System Arming
Area Assignment: Your security system has been set up into
separate areas. The number of areas and their names are listed in the back of this guide.
Arming or Disarming: You can arm and disarm all areas at one time or each area individually. You can only arm or disarm areas authorized for your user code.
Arm all or Selective Arming: After entering your user code, the system allows you to arm either all of the areas to which you have access or one or more selected areas. If you choose to arm all areas, the system begins verifying that all zones in those areas are in a good condition. If you choose to arm selected areas, the system prompts you to choose the areas you want to arm.
Arming the System:
1. Press the COMMAND key until ARM DISARM is displayed.
2. Select ARM to arm the system.
3. Enter your user code if required. The display reads ALL? NO YES.
4. Select NO to arm only selected areas. Go to step 5. Select YES to arm all areas authorized for your user code. Go to step 6.
5. If you selected NO in step 4, the display begins to list each area to which you have access followed by NO YES.
Example: OFFICE NO YES 5a. Select YES for each area you want to arm. 5b. Select NO for each area you do not want to arm.
Note: You can also just press the area numbers you want to arm
while at the ALL? NO YES display. This changes the display to AREAS: . The area numbers you select appear in the display. For example: AREAS: 2 4 . Press COMMAND when done.
6. The system displays any bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
7. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 7a through 7d.
7a. If a problem exists on a zone, the zone name and problem
is shown followed by: OKAY BYPASS STOP. 7b. Select OKAY to force arm the bad zone. 7c. Select BYPASS to bypass all bad zones being displayed. 7d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
8. The display reads SYSTEM ON if at least one area in the system is armed, and ALL SYSTEM ON if all areas in the system are armed.
9. The keypad then displays the exit time in seconds and counts down the remaining time: EXIT : ## (## = seconds remaining) The exit zones arm when the delay time expires.
Arming and Disarming
7
Area System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the entry delay time expires or an alarm on the door zone will occur.
During the entry delay time, the keypad displays ENTER CODE:. Enter your code to disarm the system. Only those areas assigned to your code will disarm.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
All or Selective Disarming: After entering your user code, the system allows you to disarm either all of the areas to which you have access or just selected areas. If you choose to disarm all areas, the system automatically disarms them. If you choose to disarm selected areas, the names of those areas will be displayed on the keypad.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Disarming an Area System
1. Press the COMMAND key until ARM DISARM is displayed. During entry delay this process starts at step 3.
2. Select DISARM to disarm areas.
3. The keypad displays ENTER CODE: . Enter your user code and press COMMAND. The keypad displays ALL? NO YES.
4. Select YES to disarm all areas authorized for your user code. Select NO to disarm only certain areas individually. The keypad
then displays the name of each area authorized for your user code followed by the NO YES display.
Choose YES to disarm the area displayed. Choose NO to not disarm and to display the next area.
Note: You can also just press the area numbers you want to disarm
while at the ALL? NO YES display. This changes the display to AREAS: . The area numbers you select appear in the display. For example: AREAS: 2 4 . Press COMMAND when done.
5. After all areas have been displayed, any alarms or communication problems that occurred during the armed period are displayed.
6. If all areas have been disarmed, the keypad next displays ALL SYSTEM OFF.
Arming and Disarming
8
Area System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the entry delay time expires or an alarm on the door zone will occur.
During the entry delay time, the keypad displays ENTER CODE:. Enter your code to disarm the system. Only those areas assigned to your code will disarm.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
All or Selective Disarming: After entering your user code, the system allows you to disarm either all of the areas to which you have access or just selected areas. If you choose to disarm all areas, the system automatically disarms them. If you choose to disarm selected areas, the names of those areas will be displayed on the keypad.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Disarming an Area System
1. Press the COMMAND key until ARM DISARM is displayed. During entry delay this process starts at step 3.
2. Select DISARM to disarm areas.
3. The keypad displays ENTER CODE: . Enter your user code and press COMMAND. The keypad displays ALL? NO YES.
4. Select YES to disarm all areas authorized for your user code. Select NO to disarm only certain areas individually. The keypad
then displays the name of each area authorized for your user code followed by the NO YES display.
Choose YES to disarm the area displayed. Choose NO to not disarm and to display the next area.
Note: You can also just press the area numbers you want to disarm
while at the ALL? NO YES display. This changes the display to AREAS: . The area numbers you select appear in the display. For example: AREAS: 2 4 . Press COMMAND when done.
5. After all areas have been displayed, any alarms or communication problems that occurred during the armed period are displayed.
6. If all areas have been disarmed, the keypad next displays ALL SYSTEM OFF.
Arming and Disarming
8
All/Perimeter System Arming
Area Assignment: Your security system is divided into two separate
areas. Motion detectors, inside doors, and other interior protection devices are assigned to the doors are assigned to the
Perimeter or All: When you go to arm an All/Perimeter system, the Security Command keypad displays PERIM ALL. If you select ALL, you’re arming both the Perimeter and the Interior areas of the system. You’ll want to arm both of these areas when leaving the premises with nobody left inside. Selecting PERIM arms only the perimeter of the system. Perimeter arming is for when you’re staying inside but want the comfort of knowing the exterior doors and windows are armed. Perimeter arming allows you to move freely about inside without setting off any interior alarms.
Instant: During the exit delay time, you can cancel the exit and entry delays and cause all zones to be instant zones. Just press the far right SELECT key under INSTNT while the exit delay is displayed. This immediately arms the exit zones. However, no entry delay is provided and an alarm will occur should an entry door be opened.
Arming an All/Perimeter System
1. Press the COMMAND key until PERIM ALL is displayed.
2. Select ALL to arm both the perimeter and interior areas. Press PERIM to arm the perimeter area only.
3. Enter your user code if required.
Interior
area while windows and exterior
Perimeter
area.
4. The system displays any Bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
5. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 5a through 5d.
5a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP. 5b. Select OKAY to force arm the zone(s) before arming. 5c. Select BYPASS to bypass the zone(s) before arming. 5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
6. The keypad displays PERIMETER ON if only the perimeter is being armed and ALL SYSTEM ON if both the perimeter and interior are being armed.
7. The keypad next displays EXIT: ## INSTNT and begins to count down the number of seconds remaining for you to exit. When the delay expires, the exit zones are armed.
8. You can select INSTNT while EXIT: ## INSTNT is displayed to immediately arm all exit zones and make them instant. The keypad displays INSTANT.
9. When the system is fully armed, the keypad displays PERIMETER ON for perimeter arming and ALL SYSTEM ON for perimeter and interior arming.
All/Perimeter System Arming
Area Assignment: Your security system is divided into two separate
areas. Motion detectors, inside doors, and other interior protection devices are assigned to the doors are assigned to the
Perimeter or All: When you go to arm an All/Perimeter system, the Security Command keypad displays PERIM ALL. If you select ALL, you’re arming both the Perimeter and the Interior areas of the system. You’ll want to arm both of these areas when leaving the premises with nobody left inside. Selecting PERIM arms only the perimeter of the system. Perimeter arming is for when you’re staying inside but want the comfort of knowing the exterior doors and windows are armed. Perimeter arming allows you to move freely about inside without setting off any interior alarms.
Instant: During the exit delay time, you can cancel the exit and entry delays and cause all zones to be instant zones. Just press the far right select key under INSTNT while the exit delay is displayed. This immediately arms the exit zones. However, no entry delay is provided and an alarm will occur should an entry door be opened.
Arming an All/Perimeter System
1. Press the COMMAND key until PERIM ALL is displayed.
2. Select ALL to arm both the perimeter and interior areas. Press PERIM to arm the perimeter area only.
3. Enter your user code if required.
Interior
area while windows and exterior
Perimeter
area.
Arming and Disarming
4. The system displays any Bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
5. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 5a through 5d.
5a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP. 5b. Select OKAY to force arm the zone(s) before arming. 5c. Select BYPASS to bypass the zone(s) before arming. 5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
6. The keypad displays PERIMETER ON if only the perimeter is being armed and ALL SYSTEM ON if both the perimeter and interior are being armed.
7. The keypad next displays EXIT: ## INSTNT and begins to count down the number of seconds remaining for you to exit. When the delay expires, the exit zones are armed.
8. You can select INSTNT while EXIT: ## INSTNT is displayed to immediately arm all exit zones and make them instant. The keypad displays INSTANT.
9. When the system is fully armed, the keypad displays PERIMETER ON for perimeter arming and ALL SYSTEM ON for perimeter and interior arming.
9
Arming and Disarming
9
All/Perimeter System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the prewarn tone expires or an alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter your code to disarm the system.
Disarming an All/Perimeter System
1. During the entry delay time, the keypad displays ENTER CODE: . Enter your user code and press COMMAND.
2. The keypad then displays any zones that went into alarm or any communication problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Arming and Disarming
10
All/Perimeter System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the prewarn tone expires or an alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter your code to disarm the system.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user code and press COMMAND. The keypad displays DISARM SILENCE.
2. Press the SELECT key under DISARM to disarm the system and silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
3. Press the SELECT key under SILENCE to stop the bell or siren but NOT disarm the system.
If you do not press any SELECT key, or you press the COMMAND key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM
CANCELLED.
Disarming an All/Perimeter System
1. During the entry delay time, the keypad displays ENTER CODE: . Enter your user code and press COMMAND.
2. The keypad then displays any zones that went into alarm or any communication problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Arming and Disarming
10
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user code and press COMMAND. The keypad displays DISARM SILENCE.
2. Press the SELECT key under DISARM to disarm the system and silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
3. Press the SELECT key under SILENCE to stop the bell or siren but NOT disarm the system.
If you do not press any SELECT key, or you press the COMMAND key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM
CANCELLED.
Home/Away System Arming
Area Assignment: Your security system is divided into two or three
separate areas. Motion detectors, inside doors, and other interior devices are assigned to an windows and exterior doors, are assigned to a
Arming the system: When arming a Home/Away system, the keypad displays HOME AWAY or HOME SLEEP AWAY. If you select AWAY, you arm all areas of the system. You’ll want to arm all areas when leaving with nobody staying inside. Selecting HOME arms only the Perimeter of the system. Perimeter arming is for when you’re staying inside but want the comfort of knowing the exterior doors and windows are armed. Perimeter arming allows you to move freely about inside without setting off any interior alarms.
Selecting SLEEP arms the Perimeter and Interior devices but leaves devices near bedrooms or other nighttime areas off.
System Ready/System Not Ready Keypad Displays
When all zones in the system are in a normal condition and can be armed without bypassing, the keypad displays SYSTEM READY. If there are one or more zones that are not in a normal condition, the keypad displays SYSTEM NOT READY. Pressing any top row SELECT key during this display shows the zone number and name allowing you to investigate the problem.
Arming a Home/Away System
1. Enter a 2 to 3 digit code and press the COMMAND key or enter a 4 digit code without pressing the COMMAND key. The keypad displays HOME AWAY or HOME SLEEP AWAY (your system may have two or three areas.
2. Select HOME to arm the Perimeter only.
Interior
and possibly
Bedroom
Perimeter
area while
area.
3. Select SLEEP to arm the Perimeter and Interior.
4. Select AWAY to arm the Perimeter, Interior, and Bedroom.
5. The system displays any Bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
6. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 6a through 6d.
6a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP. 6b. Select OKAY to force arm the zone(s) before arming. 6c. Select BYPASS to bypass the zone(s) before arming. 6d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
7. The keypad displays PERIMETER ON if you selected HOME, PERIM/INT ON if you selected SLEEP, and ALL SYSTEM ON if you selected AWAY.
8. The keypad next displays EXIT: ## INSTNT and begins to count down the number of seconds remaining for you to exit. When the delay expires, the exit zones are armed.
9. You can select INSTNT while EXIT: ## INSTNT is displayed to immediately arm all exit zones and make them instant. The keypad displays INSTANT.
Arming and Disarming
11
Home/Away System Arming
Area Assignment: Your security system is divided into two or three
separate areas. Motion detectors, inside doors, and other interior devices are assigned to an windows and exterior doors, are assigned to a
Arming the system: When arming a Home/Away system, the keypad displays HOME AWAY or HOME SLEEP AWAY. If you select AWAY, you arm all areas of the system. You’ll want to arm all areas when leaving with nobody staying inside. Selecting HOME arms only the Perimeter of the system. Perimeter arming is for when you’re staying inside but want the comfort of knowing the exterior doors and windows are armed. Perimeter arming allows you to move freely about inside without setting off any interior alarms.
Selecting SLEEP arms the Perimeter and Interior devices but leaves devices near bedrooms or other nighttime areas off.
System Ready/System Not Ready Keypad Displays
When all zones in the system are in a normal condition and can be armed without bypassing, the keypad displays SYSTEM READY. If there are one or more zones that are not in a normal condition, the keypad displays SYSTEM NOT READY. Pressing any top row SELECT key during this display shows the zone number and name allowing you to investigate the problem.
Arming a Home/Away System
1. Enter a 2 to 3 digit code and press the COMMAND key or enter a 4 digit code without pressing the COMMAND key. The keypad displays HOME AWAY or HOME SLEEP AWAY (your system may have two or three areas.
2. Select HOME to arm the Perimeter only.
Interior
and possibly
Bedroom
Perimeter
area while
area.
3. Select SLEEP to arm the Perimeter and Interior.
4. Select AWAY to arm the Perimeter, Interior, and Bedroom.
5. The system displays any Bypassed zones or bad 24 hour or Priority zones. A bad Priority zone cannot be armed.
6. At this point you can force arm or bypass any bad zones. A zone that is force armed will be restored into the system if it later returns to normal. A zone that is bypassed will remain bypassed until the system is disarmed. See steps 6a through 6d.
6a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP. 6b. Select OKAY to force arm the zone(s) before arming. 6c. Select BYPASS to bypass the zone(s) before arming. 6d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
7. The keypad displays PERIMETER ON if you selected HOME, PERIM/INT ON if you selected SLEEP, and ALL SYSTEM ON if you selected AWAY.
8. The keypad next displays EXIT: ## INSTNT and begins to count down the number of seconds remaining for you to exit. When the delay expires, the exit zones are armed.
9. You can select INSTNT while EXIT: ## INSTNT is displayed to immediately arm all exit zones and make them instant. The keypad displays INSTANT.
Arming and Disarming
11
Home/Away System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the prewarn tone expires or an alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter your code to disarm the system.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Disarming a Home/Away System
1. During the entry delay, the keypad displays ENTER CODE:. Enter a 2 to 3 digit user code and press COMMAND or enter a 4 digit code without pressing COMMAND.
2. The keypad then displays any alarms or communication problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter a 2 to 3 digit user code and press COMMAND or enter a 4 digit user code. The keypad displays DISARM SILENCE.
2. Press the SELECT key under DISARM to disarm the system and silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
3. Press the SELECT key under SILENCE to stop the bell or siren but NOT disarm the system.
If you do not press any SELECT key, or you press the COMMAND key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM
CANCELLED.
12
Arming and Disarming
Home/Away System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the prewarn tone expires or an alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter your code to disarm the system.
Schedules: If you’ve programmed schedules for your system and a level 2 code is entered outside of a schedule, the keypad displays INVALID TIME. This lets the user know that they are disarming outside of their authorized time. If your system is monitored, an Unauthorized Entry report is sent to the central station.
Alarm Display: After disarming, the keypad displays any zones that tripped or any transmission problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.
Central Station Report: A report of the system disarming can be transmitted to the central station. This is optional and can be programmed for you at any time.
Disarming a Home/Away System
1. During the entry delay, the keypad displays ENTER CODE:. Enter a 2 to 3 digit user code and press COMMAND or enter a 4 digit code without pressing COMMAND.
2. The keypad then displays any alarms or communication problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter a 2 to 3 digit user code and press COMMAND or enter a 4 digit user code. The keypad displays DISARM SILENCE.
2. Press the SELECT key under DISARM to disarm the system and silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the system is disarmed.
3. Press the SELECT key under SILENCE to stop the bell or siren but NOT disarm the system.
If you do not press any SELECT key, or you press the COMMAND key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED.
Arming and Disarming
12
User Menu
Security Command User Menu
Many of the features of your system have been put into a User Menu that you can access from any Security Command keypad. The menu requires you to enter your user code and then only shows those functions to which you have access.
To access the User Menu:
1. Press the COMMAND key until MENU? NO YES displays.
2. Select YES. The keypad displays ENTER CODE: –. Enter your user code and press COMMAND. You can now scroll down through the list of system features available to your authority level.
User Menu Options
The list below shows the User Menu options in order:
Menu Option Description
ALARM SILENCE Silences an alarm bell or siren. SENSOR RESET Resets smoke or glassbreak detectors
that have latched due to an alarm condition.
DOOR ACCESS Opens the keypad door lock relay
momentarily.
ARMED AREAS Displays the name of any areas in the
system that are currently in the armed state.
OUTPUTS ON/OFF Allows you to turn on or off any of the
outputs described in the System Setup section of this guide.
ZONE STATUS Allows you to enter a zone number and
see if that zone is either armed, bypassed, in alarm, open, or shorted.
BYPASS ZONES Allows you to Bypass a zone or reset
an already bypassed zone.
ZONE MONITOR Allows you to add or remove a zone
from the monitor mode.
SYSTEM STATUS Displays the current condition of the
system's AC power, backup battery, and panel tamper (optional).
SYSTEM TEST Tests the system's siren,
communication to the central station, and backup battery.
USER CODES Allows you to add, delete, or change
user codes and authority levels.
SCHEDULES Allows you to add, remove, or change
system schedules.
TIME Allows you change the Day, Date, or
Time that is currently in the system.
DISPLAY EVENTS Allows you to view or print the last 200
events that occurred on your system.
SERVICE REQUEST Allows you to send a message to the
Central Station requesting service on the alarm system.
The following pages detail each user menu item and provide instructions on when and how to use them properly.
User Menu
13
User Menu
Security Command User Menu
Many of the features of your system have been put into a User Menu that you can access from any Security Command keypad. The menu requires you to enter your user code and then only shows those functions to which you have access.
To access the User Menu:
1. Press the COMMAND key until MENU? NO YES displays.
2. Select YES. The keypad displays ENTER CODE: –. Enter your user code and press COMMAND. You can now scroll down through the list of system features available to your authority level.
User Menu Options
The list below shows the User Menu options in order:
Menu Option Description
ALARM SILENCE Silences an alarm bell or siren. SENSOR RESET Resets smoke or glassbreak detectors
that have latched due to an alarm condition.
DOOR ACCESS Opens the keypad door lock relay
momentarily.
ARMED AREAS Displays the name of any areas in the
system that are currently in the armed state.
OUTPUTS ON/OFF Allows you to turn on or off any of the
outputs described in the System Setup section of this guide.
ZONE STATUS Allows you to enter a zone number and
see if that zone is either armed, bypassed, in alarm, open, or shorted.
BYPASS ZONES Allows you to Bypass a zone or reset
an already bypassed zone.
ZONE MONITOR Allows you to add or remove a zone
from the monitor mode.
SYSTEM STATUS Displays the current condition of the
system's AC power, backup battery, and panel tamper (optional).
SYSTEM TEST Tests the system's siren,
communication to the central station, and backup battery.
USER CODES Allows you to add, delete, or change
user codes and authority levels.
SCHEDULES Allows you to add, remove, or change
system schedules.
TIME Allows you change the Day, Date, or
Time that is currently in the system.
DISPLAY EVENTS Allows you to view or print the last 200
events that occurred on your system.
SERVICE REQUEST Allows you to send a message to the
Central Station requesting service on the alarm system.
The following pages detail each user menu item and provide instructions on when and how to use them properly.
User Menu
13
Alarm Silence
User Code Level: 2 and above. Function: Silences the alarm bell or siren during an alarm.
Alarm Silence allows you to turn off the alarm bell or siren connected to your system during an alarm. Using Alarm Silence does NOT stop an alarm report from being sent to the central station and does not reset any alarmed devices. Use the Sensor Reset function to reset devices such as smoke detectors that have latched in alarm.
Note: You can also silence an alarm by entering your user code and pressing COMMAND while the bell or siren is still sounding.
Using the Alarm Silence Function
1. Access the User Menu.
2. The keypad displays ALARM SILENCE?.
3. Press any SELECT key. The system silences the bell or siren and exits the User Menu.
Sensor Reset
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Resets smoke or glassbreak detectors. Also clears Fire/
Supervisory alarm and trouble displays. Sensor Reset is used to reset smoke and glassbreak detectors after
they have been tripped. Once these detectors have tripped, they must be reset before they can detect any additional alarm conditions. When Sensor Reset is selected, power to the detectors is temporarily removed by the system allowing them to reset.
Make sure all smoke is cleared from around the area of the smoke detectors before performing a Sensor Reset to prevent the alarm from occurring again.
Resetting the Sensors
1. Access the User Menu.
2. Press COMMAND until SENSOR RESET displays.
3. The keypad displays SENSORS OFF for five seconds followed by SENSORS ON.
4. The keypad automatically exits the User Menu.
14
User Menu
Alarm Silence
User Code Level: 2 and above. Function: Silences the alarm bell or siren during an alarm.
Alarm Silence allows you to turn off the alarm bell or siren connected to your system during an alarm. Using Alarm Silence does NOT stop an alarm report from being sent to the central station and does not reset any alarmed devices. Use the Sensor Reset function to reset devices such as smoke detectors that have latched in alarm.
Note: You can also silence an alarm by entering your user code and pressing COMMAND while the bell or siren is still sounding.
Using the Alarm Silence Function
1. Access the User Menu.
2. The keypad displays ALARM SILENCE?.
3. Press any SELECT key. The system silences the bell or siren and exits the User Menu.
Sensor Reset
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Resets smoke or glassbreak detectors. Also clears Fire/
Supervisory alarm and trouble displays. Sensor Reset is used to reset smoke and glassbreak detectors after
they have been tripped. Once these detectors have tripped, they must be reset before they can detect any additional alarm conditions. When Sensor Reset is selected, power to the detectors is temporarily removed by the system allowing them to reset.
Make sure all smoke is cleared from around the area of the smoke detectors before performing a Sensor Reset to prevent the alarm from occurring again.
Resetting the Sensors
1. Access the User Menu.
2. Press COMMAND until SENSOR RESET displays.
3. The keypad displays SENSORS OFF for five seconds followed by SENSORS ON.
4. The keypad automatically exits the User Menu.
User Menu
14
Door Access
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Operates an electric door strike from the keypad.
Armed Areas Display
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Displays all armed areas in the system.
Door Access is used to operate a door strike relay that is built into some Security Command keypads. Power for the door strike is connected to the keypad relay and can be interrupted by using the Door Access function.
When Door Access is selected you’ll be asked to enter your user code. When the user code is accepted, the door strike at the Security Command you’re operating turns on momentarily.
Door Access also functions any time any area of the system is disarmed at the door strike keypad or by simply entering your user code and pressing COMMAND.
A report of this entry can be transmitted to your central station. This report is optional and can be programmed for you at any time.
Using the Door Access
1. Access the User Menu.
2. Press COMMAND until DOOR ACCESS? displays.
3. Press any SELECT key. The door strike relay turns on momentarily.
4. The keypad returns to the Status List display.
Armed Areas is used to display all of the armed areas in your system at the Security Command keypads. Each armed area is displayed along with its area number and name.
Using the Armed Areas Function
1. Access the User Menu.
2. Press COMMAND until ARMED AREAS? displays.
3. Press any SELECT key. The keypad displays the first armed area name. To scroll through the list of armed areas, press the COMMAND key.
All/Perimeter and Home/Away systems: Armed areas for these systems are shown as PERIMETER, INTERIOR, and also BEDROOMS for Home/Away systems.
4. If there are no armed areas, the keypad displays NONE.
Door Access
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Operates an electric door strike from the keypad.
Door Access is used to operate a door strike relay that is built into some Security Command keypads. Power for the door strike is connected to the keypad relay and can be interrupted by using the Door Access function.
When Door Access is selected you’ll be asked to enter your user code. When the user code is accepted, the door strike at the Security Command you’re operating turns on momentarily.
Door Access also functions any time any area of the system is disarmed at the door strike keypad or by simply entering your user code and pressing COMMAND.
A report of this entry can be transmitted to your central station. This report is optional and can be programmed for you at any time.
Using the Door Access
1. Access the User Menu.
2. Press COMMAND until DOOR ACCESS? displays.
3. Press any SELECT key. The door strike relay turns on momentarily.
4. The keypad returns to the Status List display.
User Menu
15
Armed Areas Display
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Displays all armed areas in the system.
Armed Areas is used to display all of the armed areas in your system at the Security Command keypads. Each armed area is displayed along with its area number and name.
Using the Armed Areas Function
1. Access the User Menu.
2. Press COMMAND until ARMED AREAS? displays.
3. Press any SELECT key. The keypad displays the first armed area name. To scroll through the list of armed areas, press the COMMAND key.
All/Perimeter and Home/Away systems: Armed areas for these systems are shown as PERIMETER, INTERIOR, and also BEDROOMS for Home/Away systems.
4. If there are no armed areas, the keypad displays NONE.
User Menu
15
Outputs On Off
User Code Level: 5 and above. Function: Allows you to turn the system relay outputs on and off.
This function is used to individually turn your system’s relay outputs on and off. Your system may use these outputs to control interior and exterior lighting, heating, air conditioning, or other appliances.
The names and numbers of the relays connected to your system are located in the System Setup section of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2. Press COMMAND until OUTPUTS ON/OFF? displays.
3. Press any SELECT key to display OUTPUT: - ON OFF.
4. Enter the output number you want to turn on or off. The output number will appear in the display.
5. With the output number displayed, press the SELECT key under ON or OFF. The output is then turned on or off, depending on your selection, and remains in that state until you change it.
Under certain conditions, some outputs cannot be turned on. If you select a restricted output, the keypad displays CANNOT TURN ON.
6. The system automatically removes the output number and a new output number can be entered. Refer back to step 4.
Press the ARROW key to exit the User Menu.
Zone Status
User Code Level: All users at any time. Function: Displays a list of armed, bypassed, or alarmed zones.
Also allows you to check the status of individual zones. Zone Status can be used to give you a list of zones by category or
display the current status of an individual zone number. The four categories are:
• Armed Zones - zones that are currently armed.
• Bypassed Zones - zones that are currently bypassed.
• Alarmed Zones - zones that have gone into alarm during the current or previous armed period.
• Number - enter the number of any zone to check its status.
Using the Zone Status Function
1. Access the User Menu.
2. Press COMMAND until ZONE STATUS? is displayed.
3. Press any SELECT key to display ARM BYPS ALR NBR.
4. Select ARM for a list of zones that are currently armed. You can scroll through the list by pressing the COMMAND key.
5. Select BYPS for a list of zones that are currently bypassed.
6. Select ALR for a list of zones that have gone into alarm during the current or previous armed period.
7. Press NBR and ZONE NO: - will be displayed.
16
User Menu
Outputs On Off
User Code Level: 5 and above. Function: Allows you to turn the system relay outputs on and off.
This function is used to individually turn your system’s relay outputs on and off. Your system may use these outputs to control interior and exterior lighting, heating, air conditioning, or other appliances.
The names and numbers of the relays connected to your system are located in the System Setup section of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2. Press COMMAND until OUTPUTS ON/OFF? displays.
3. Press any SELECT key to display OUTPUT: - ON OFF.
4. Enter the output number you want to turn on or off. The output number will appear in the display.
5. With the output number displayed, press the SELECT key under ON or OFF. The output is then turned on or off, depending on your selection, and remains in that state until you change it.
Under certain conditions, some outputs cannot be turned on. If you select a restricted output, the keypad displays CANNOT TURN ON.
6. The system automatically removes the output number and a new output number can be entered. Refer back to step 4.
Press the ARROW key to exit the User Menu.
Zone Status
User Code Level: All users at any time. Function: Displays a list of armed, bypassed, or alarmed zones.
Also allows you to check the status of individual zones. Zone Status can be used to give you a list of zones by category or
display the current status of an individual zone number. The four categories are:
• Armed Zones - zones that are currently armed.
• Bypassed Zones - zones that are currently bypassed.
• Alarmed Zones - zones that have gone into alarm during the current or previous armed period.
• Number - enter the number of any zone to check its status.
Using the Zone Status Function
1. Access the User Menu.
2. Press COMMAND until ZONE STATUS? is displayed.
3. Press any SELECT key to display ARM BYPS ALR NBR.
4. Select ARM for a list of zones that are currently armed. You can scroll through the list by pressing the COMMAND key.
5. Select BYPS for a list of zones that are currently bypassed.
6. Select ALR for a list of zones that have gone into alarm during the current or previous armed period.
7. Press NBR and ZONE NO: - will be displayed.
User Menu
16
Zone Status continued
8. At the ZONE NO: - prompt, enter the zone number you want to check and press COMMAND. The zone number and name is displayed followed by its status. For example, a zone status for zone 1 might be: BACK DOOR - OKAY.
Below is a list of the zone status displays:
-OKAY = the zone is in a normal condition
-BYPAS = the zone is bypassed
-BAD = the zone is in a bad condition
9. After displaying the zone status, ZONE: - returns for you to enter another zone number.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Zone Status browser.
Bypass Zones
User Code Level: 6 and above. Function: Allows you to bypass a zone prior to arming.
Bypassing is usually done when a zone cannot be restored to normal. A zone can be bypassed only while it’s disarmed. Since fire, panic, emergency, and supervisory type zones are always armed, they can never be bypassed.
Bypass Zones can also be used to reset a zone that has been bypassed and restore it back into the system. This can only be done while the zone is disarmed.
When Bypass Zones is selected, a report can be transmitted to your central station.
Using the Bypass Zones Function
1. Access the User Menu.
2. Press COMMAND until BYPASS ZONES? displays.
3. Press any SELECT key. The keypad displays ZONE: - RST BYPS.
4. To Bypass a zone, enter the zone number and select BYPS. The zone number automatically disappears and a new zone number can be entered. Refer back to step 3.
5. To Reset a zone, enter the zone number and select RST.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Bypass Zones browser.
Zone Status continued
8. At the ZONE NO: - prompt, enter the zone number you want to check and press COMMAND. The zone number and name is displayed followed by its status. For example, a zone status for zone 1 might be: BACK DOOR - OKAY.
Below is a list of the zone status displays:
-OKAY = the zone is in a normal condition
-BYPAS = the zone is bypassed
-BAD = the zone is in a bad condition
9. After displaying the zone status, ZONE: - returns for you to enter another zone number.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Zone Status browser.
User Menu
Bypass Zones
User Code Level: 6 and above. Function: Allows you to bypass a zone prior to arming.
Bypassing is usually done when a zone cannot be restored to normal. A zone can be bypassed only while it’s disarmed. Since fire, panic, emergency, and supervisory type zones are always armed, they can never be bypassed.
Bypass Zones can also be used to reset a zone that has been bypassed and restore it back into the system. This can only be done while the zone is disarmed.
When Bypass Zones is selected, a report can be transmitted to your central station.
Using the Bypass Zones Function
1. Access the User Menu.
2. Press COMMAND until BYPASS ZONES? displays.
3. Press any SELECT key. The keypad displays ZONE: - RST BYPS.
4. To Bypass a zone, enter the zone number and select BYPS. The zone number automatically disappears and a new zone number can be entered. Refer back to step 3.
5. To Reset a zone, enter the zone number and select RST.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Bypass Zones browser.
17
User Menu
17
Zone Monitor
User Code Level: 4 and above. Function: Allows the system to monitor selected disarmed zones
(doors, windows, or motion detectors) and display their name at the keypad as they're faulted.
Zone Monitor works with any disarmed zone and will also sound the keypad monitor tone when the zone faults. The zone name is displayed at all keypads in your system.
You can place any combination of disarmed zones in Zone Monitor but only the most recent zone faulted is displayed. The displayed zone name clears automatically after a short time or when the zone is armed.
Using Zone Monitor as part of your weekly system test: After using the System Test function (see page 19), place all perimeter and interior zones in Zone Monitor. Starting at the front door, go around and open and then close each door and window. You should hear the keypad beep each time. The keypad will also display the name of each zone as its device is opened.
Once all protected doors and windows have been tested, walk in front of each motion detector. The keypad should beep to confirm their operation. If at any time during your weekly testing a device does not cause the keypad to beep, call the service department for assistance.
Using the Zone Monitor Function
1. Access the User Menu.
2. Press COMMAND until ZONE MONITOR? displays.
18
User Menu
3. Press any SELECT key. The keypad displays ALL NBR for an Area system (skip ahead to number 5) and PERIM ALL NBR for an All/Perimeter or Home/Away system.
4. Select PERIM to place all disarmed perimeter zones into Zone Monitor. PERIM is displayed only on All/Perimeter and Home/ Away systems.
4a. The keypad displays PERIM? ADD RMV. 4b. Select ADD to put all perimeter zones into Zone Monitor. 4c. Select RMV to remove all perimeter zones.
5. Select ALL to place all disarmed zones into Zone Monitor. 5a. The keypad displays ALL? ADD RMV. 5b. Select ADD to add all disarmed zones to Zone Monitor. 5c. Select RMV to remove all disarmed zones.
6. Select NBR to enter a specific zone number for zone monitor.
7. If NBR is selected, the keypad displays ZONE: - ADD RMV. 7a. Enter any zone number and select ADD to add this zone. 7b. Enter any zone number and select RMV to remove this
zone.
8. The zone number automatically disappears and a new zone number can then be entered in step 7a or 7b.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Zone Monitor browser.
Zone Monitor
User Code Level: 4 and above. Function: Allows the system to monitor selected disarmed zones
(doors, windows, or motion detectors) and display their name at the keypad as they're faulted.
Zone Monitor works with any disarmed zone and will also sound the keypad monitor tone when the zone faults. The zone name is displayed at all keypads in your system.
You can place any combination of disarmed zones in Zone Monitor but only the most recent zone faulted is displayed. The displayed zone name clears automatically after a short time or when the zone is armed.
Using Zone Monitor as part of your weekly system test: After using the System Test function (see page 19), place all perimeter and interior zones in Zone Monitor. Starting at the front door, go around and open and then close each door and window. You should hear the keypad beep each time. The keypad will also display the name of each zone as its device is opened.
Once all protected doors and windows have been tested, walk in front of each motion detector. The keypad should beep to confirm their operation. If at any time during your weekly testing a device does not cause the keypad to beep, call the service department for assistance.
Using the Zone Monitor Function
1. Access the User Menu.
2. Press COMMAND until ZONE MONITOR? displays.
User Menu
18
3. Press any SELECT key. The keypad displays ALL NBR for an Area system (skip ahead to number 5) and PERIM ALL NBR for an All/Perimeter or Home/Away system.
4. Select PERIM to place all disarmed perimeter zones into Zone Monitor. PERIM is displayed only on All/Perimeter and Home/ Away systems.
4a. The keypad displays PERIM? ADD RMV. 4b. Select ADD to put all perimeter zones into Zone Monitor. 4c. Select RMV to remove all perimeter zones.
5. Select ALL to place all disarmed zones into Zone Monitor. 5a. The keypad displays ALL? ADD RMV. 5b. Select ADD to add all disarmed zones to Zone Monitor. 5c. Select RMV to remove all disarmed zones.
6. Select NBR to enter a specific zone number for zone monitor.
7. If NBR is selected, the keypad displays ZONE: - ADD RMV. 7a. Enter any zone number and select ADD to add this zone. 7b. Enter any zone number and select RMV to remove this
zone.
8. The zone number automatically disappears and a new zone number can then be entered in step 7a or 7b.
☞ Browser Feature
If you’re unsure of the zone number or description, refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Zone Monitor browser.
System Status
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Displays the current condition of internal system hardware.
System Status displays the condition of the panel's AC power, battery power, and optional panel tamper. When System Status is selected, each monitor is displayed followed by OKAY or TRBL (Trouble) to indicate the current condition.
Using the System Status Function
1. Access the User Menu.
2. Press COMMAND until SYSTEM STATUS? displays.
3. Press any SELECT key. The display starts listing each system monitor and status.
For example: AC POWER - OKAY
Below are the System Monitor displays:
Keypad Display What it monitors
AC POWER = AC power BATTERY = Battery power TAMPER = Panel box tamper
These are followed by either OKAY or TRBL (trouble). If TRBL is displayed, call the service department for assistance.
4. The system then displays its firmware version (for example, VER_102_10/17/97), the panel model (MODEL XR200), then exits the User Menu.
System Test
User Code Level: 4 and above. Function: System Test is used to test the battery, alarm bell or siren,
and communication to a central station. The System Test function begins automatically as soon as you select it.
Using the System Test Function
1. Access the User Menu.
2. Press COMMAND until SYSTEM TEST? displays.
3. Press any SELECT key. The system test begins automatically and the keypad displays:
1) BELL SOUNDING during a two second bell test, then:
2) BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery, then:
* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test, then:
4) TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test, then:
5) TEST END to indicate the System Test is complete.
6) You can end the transmit test by pressing the ARROW key.
* The transmit test does not operate on local systems.
Testing your system’s burglary protection: The System Test
function should be a part of your weekly testing and should be followed by placing the interior and perimeter burglary devices in Zone Monitor mode. This allows you to open and then close each protected door and window while listening for the keypad to beep confirming its operation. See Zone Monitor.
System Status
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Displays the current condition of internal system hardware.
System Status displays the condition of the panel's AC power, battery power, and optional panel tamper. When System Status is selected, each monitor is displayed followed by OKAY or TRBL (Trouble) to indicate the current condition.
Using the System Status Function
1. Access the User Menu.
2. Press COMMAND until SYSTEM STATUS? displays.
3. Press any SELECT key. The display starts listing each system monitor and status.
For example: AC POWER - OKAY
Below are the System Monitor displays:
Keypad Display What it monitors
AC POWER = AC power BATTERY = Battery power TAMPER = Panel box tamper
These are followed by either OKAY or TRBL (trouble). If TRBL is displayed, call the service department for assistance.
4. The system then displays its firmware version (for example, VER_102_10/17/97), the panel model (MODEL XR200), then exits the User Menu.
User Menu
19
System Test
User Code Level: 4 and above. Function: System Test is used to test the battery, alarm bell or siren,
and communication to a central station. The System Test function begins automatically as soon as you select it.
Using the System Test Function
1. Access the User Menu.
2. Press COMMAND until SYSTEM TEST? displays.
3. Press any SELECT key. The system test begins automatically and the keypad displays:
1) BELL SOUNDING during a two second bell test, then:
2) BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery, then:
* 3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test, then:
4) TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test, then:
5) TEST END to indicate the System Test is complete.
6) You can end the transmit test by pressing the ARROW key.
* The transmit test does not operate on local systems.
Testing your system’s burglary protection: The System Test
function should be a part of your weekly testing and should be followed by placing the interior and perimeter burglary devices in Zone Monitor mode. This allows you to open and then close each protected door and window while listening for the keypad to beep confirming its operation. See Zone Monitor.
User Menu
19
User Codes
User Code Level: 9 only. Function: Allows you to add, delete, and change a user's (person
operating the system) user code or authority level. There are three characteristics associated with each user code that
define its capabilities within the system.
125 34812 7
User Number User Code User Level
User Number - Every user is numbered. This number identifies them to the system and can be transmitted to the central station when they arm or disarm areas.
User Code - Each user also has a 3 to 5 digit number they enter into the Security Command keypad when arming or disarming the system. NOTE: A User Code cannot begin or end with zero or be in the range of 1 to 299.
User Names - Each code may also be programmed with the user’s name. Up to 16 characters may be entered.
Areas - Each user may be assigned specific areas in the burglary alarm system.
User Level - The user is also assigned a level of authority (1 to 9) or customized authority by the person administrating the system that determines the functions the user can access.
Important: Each area must have at least one user with a level 9 authority in order to be able to add or delete user codes.
The following table lists system functions users are allowed to access based on the authority level assigned to their codes.
User Code Authority Levels
Menu Options 1 2 3 4 5 6 7 8 9
Sensor Reset Armed Areas Zone Status System Status Display Events Door Access Arm and Disarm Alarm Silence System Test √√√√√√ Zone Monitor √√√√√√ Outputs On/Off √√√√√ Extend √√√√ Bypass Zones √√√√ Schedules √√√ Set Time √√ User Codes √
* = These functions can only be accessed during certain schedules. + = Arming allowed anytime. Disarming allowed outside of a schedule
but an Unauthorized Entry report is sent to the central station.
**√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√
+ √√√√√√√
* √√√√√√√
20
User Menu
User Codes
User Code Level: 9 only. Function: Allows you to add, delete, and change a user's (person
operating the system) user code or authority level. There are three characteristics associated with each user code that
define its capabilities within the system.
125 34812 7
User Number User Code User Level
User Number - Every user is numbered. This number identifies them to the system and can be transmitted to the central station when they arm or disarm areas.
User Code - Each user also has a 3 to 5 digit number they enter into the Security Command keypad when arming or disarming the system. NOTE: A User Code cannot begin or end with zero or be in the range of 1 to 299.
User Names - Each code may also be programmed with the user’s name. Up to 16 characters msy be entered.
Areas - Each user may be assigned specific areas in the burglary alarm system.
User Level - The user is also assigned a level of authority (1 to 9) or customized authority by the person administrating the system that determines the functions the user can access.
Important: Each area must have at least one user with a level 9 authority in order to be able to add or delete user codes.
The following table lists system functions users are allowed to access based on the authority level assigned to their codes.
User Code Authority Levels
Menu Options 1 2 3 4 5 6 7 8 9
Sensor Reset Armed Areas Zone Status System Status Display Events Door Access Arm and Disarm Alarm Silence System Test √√√√√√ Zone Monitor √√√√√√ Outputs On/Off √√√√√ Extend √√√√ Bypass Zones √√√√ Schedules √√√ Set Time √√ User Codes √
* = These functions can only be accessed during certain schedules. + = Arming allowed anytime. Disarming allowed outside of a schedule
but an Unauthorized Entry report is sent to the central station.
**√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√ **√√√√√√√
+ √√√√√√√
* √√√√√√√
User Menu
20
User Codes continued
Programming Custom User Codes
In addition to the preset authority levels, you can also create custom authority levels by selecting the CUSTOM option at the time the user is being added to the system. This option allows you to assign specific User Menu access to individual users.
Adding User Codes:
1. Access the User Menu.
2. Press COMMAND until USER CODES? displays. (NOTE: You must have a level 9 authority. If you enter the User Menu with a lower authority, the keypad will not display USER CODES?.)
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under ADD to add a new user code.
5. At the USER NUMBER:- prompt, enter a user number and press COMMAND. The display changes to CODE NO:- .
6. Enter a user code of 3 to 5 digits (4 digits on the Home/Away system) and press COMMAND. The user enters this number each time they arm, disarm, or make changes. If using access cards, present the card instead of entering a code. After the code is entered, the display changes to USER NUMBER ###.
7. A 16 character name may be entered to identify the user. Press any top row key to clear the current name. You may then enter the new name. After the name is entered, press COMMAND. See Entering Custom Names in the Appendix of this User’s Guide.
8.
Areas systems only
(# = area number). Add or remove access to one or more areas by pressing the corresponding number keys. Press COMMAND.
Note: You may only add areas that are assigned to your code.
- The display changes to AREAS: # # # #
9. The display changes to LEVEL CUSTOM. Select LEVEL to assign a standard set of authorized functions as outlined in the User Code Authority Levels table on the previous page.
10. At the LEVEL: - display, enter an authority level from 1 to 9. Press COMMAND. The displays shows USER # ADDED.
11. Select CUSTOM to customize the functions you want the user to access. This allows users to have certain capabilities outside of a standard authority level. The following chart shows the custom menu with default selections.
ARM/DIS (arm & disarm) NO SYS STAT (system status) NO ALM SLNC (alarm silence) NO SYS TEST (system test) NO SNSR RST (sensor reset) NO USR CODE (user codes) NO DOOR ACS (door access) NO SCHEDULS (schedules) NO ARM AREA (armed areas) NO TIME (day, date, and time) NO OUTPUTS (outputs on off) NO DIS EVNT (display events) NO ZN STATS (zone status) NO EXTEND (extend closing) NO BYPAS ZN (bypass zones) NO *TEMP CODE (temporary code) NO ZONE MON (zone monitor) NO
* • NO makes this a permanent user code.
• YES makes this a temporary code that expires in 7 days.
12. Press the ARROW key to exit the User Menu.
Note: Customized codes are not restricted to the schedules.
☞ Browser Feature
Refer to the Appendix at the back of this guide for a diagram showing you how to use the buitl-in Add User Codes browser.
User Menu
21
User Codes continued
Programming Custom User Codes
In addition to the preset authority levels, you can also create custom authority levels by selecting the CUSTOM option at the time the user is being added to the system. This option allows you to assign specific User Menu access to individual users.
Adding User Codes:
1. Access the User Menu.
2. Press COMMAND until USER CODES? displays. (NOTE: You must have a level 9 authority. If you enter the User Menu with a lower authority, the keypad will not display USER CODES?.)
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under ADD to add a new user code.
5. At the USER NUMBER:- prompt, enter a user number and press COMMAND. The display changes to CODE NO:- .
6. Enter a user code of 3 to 5 digits (4 digits on the Home/Away system) and press COMMAND. The user enters this number each time they arm, disarm, or make changes. If using access cards, present the card instead of entering a code. After the code is entered, the display changes to USER NUMBER ###.
7. A 16 character name may be entered to identify the user. Press any top row key to clear the current name. You may then enter the new name. After the name is entered, press COMMAND. See Entering Custom Names in the appendix of this User’s Guide.
8.
Areas systems only
(# = area number). Add or remove access to one or more areas by pressing the corresponding number keys. Press COMMAND.
Note: You may only add areas that are assigned to your code.
- The display changes to AREAS: # # # #
9. The display changes to LEVEL CUSTOM. Select LEVEL to assign a standard set of authorized functions as outlined in the User Code Authority Levels table on the previous page.
10. At the LEVEL: - display, enter an authority level from 1 to 9. Press COMMAND. The displays shows USER # ADDED.
11. Select CUSTOM to customize the functions you want the user to access. This allows users to have certain capabilities outside of a standard authority level. The following chart shows the custom menu with default selections.
ARM/DIS (arm & disarm) NO SYS STAT (system status) NO ALM SLNC (alarm silence) NO SYS TEST (system test) NO SNSR RST (sensor reset) NO USR CODE (user codes) NO DOOR ACS (door access) NO SCHEDULS (schedules) NO ARM AREA (armed areas) NO TIME (day, date, and time) NO OUTPUTS (outputs on off) NO DIS EVNT (display events) NO ZN STATS (zone status) NO EXTEND (extend closing) NO BYPAS ZN (bypass zones) NO *TEMP CODE (temporary code) NO ZONE MON (zone monitor) NO
* • NO makes this a permanent user code.
• YES makes this a temporary code that expires in 7 days.
12. Press the ARROW key to exit the User Menu.
Note: Customized codes are not restricted to the schedules.
☞ Browser Feature
Refer to the Appendix at the back of this guide for a diagram showing you how to use the buitl-in Add User Codes browser.
User Menu
21
User Codes continued
Ambush Codes
Changing User Codes
Your system may be programmed to allow user number 1 to be an Ambush code. This Ambush code functions identically to a standard code with the exception that it sends a silent alarm to the central station. This silent alarm alerts the operator to a duress situation at the premises and prompts the immediate notification of authorities.
Refer to the System Setup section of this guide to see if your system is programmed for Ambush. If so, do NOT program a code for user number 1 unless you intend to use the Ambush function.
Deleting User Codes
1. Access the User Menu.
2. Press COMMAND until USER CODES? displays.
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under DEL to delete a user code from the system. You must have a user code level of 9 or have a custom user code with that authority to be able to delete a user code.
Important: Each area must have at least one user with a level 9 authority in order to be able to add or delete user codes. Be careful not to delete all level 9 users from an area.
5. At the USER NUMBER: - prompt, enter the user number you want to delete and press COMMAND. The displays changes to USER # DELETED.
6. The display then changes back to USER NUMBER: - allowing you to delete another user. Press the ARROW key twice to exit the User Menu.
22
User Menu
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under CHG to change a user code.
5. At the USER NUMBER: - prompt, enter the user number to change and press COMMAND.
6. The display changes to CODE NO: * * * * *. Press a SELECT key and enter the new user code. Press COMMAND.
Note: Changing a user code does not change the user number.
7. The display then shows the current user name. Press any top row key to clear. See the Entering Custom Names section in the Appendix to enter a new name.
8.
Areas systems only
(# = area number). Add or remove access to one or more areas by pressing the corresponding number keys. Press COMMAND.
9. The display changes to LEVEL CUSTOM. Refer to Adding User Codes on the previous page for a description of this prompt.
10. After entering the authority level, the keypad displays USER # CHANGED for five seconds followed by USER NUMBER: -. This display allows you to enter another user number to change. Press the ARROW key twice to exit the User Menu.
- The display changes to AREAS: # # # #
☞ Browser Feature
Refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Delete or Change User Codes browser.
User Codes continued
Ambush Codes
Your system may be programmed to allow user number 1 to be an Ambush code. This Ambush code functions identically to a standard code with the exception that it sends a silent alarm to the central station. This silent alarm alerts the operator to a duress situation at the premises and prompts the immediate notification of authorities.
Refer to the System Setup section of this guide to see if your system is programmed for Ambush. If so, do NOT program a code for user number 1 unless you intend to use the Ambush function.
Deleting User Codes
1. Access the User Menu.
2. Press COMMAND until USER CODES? displays.
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under DEL to delete a user code from the system. You must have a user code level of 9 or have a custom user code with that authority to be able to delete a user code.
Important: Each area must have at least one user with a level 9 authority in order to be able to add or delete user codes. Be careful not to delete all level 9 users from an area.
5. At the USER NUMBER: - prompt, enter the user number you want to delete and press COMMAND. The displays changes to USER # DELETED.
6. The display then changes back to USER NUMBER: - allowing you to delete another user. Press the ARROW key twice to exit the User Menu.
User Menu
22
Changing User Codes
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any SELECT key. The keypad displays ADD DEL CHG.
4. Press the SELECT key under CHG to change a user code.
5. At the USER NUMBER: - prompt, enter the user number to change and press COMMAND.
6. The display changes to CODE NO: * * * * *. Press a SELECT key and enter the new user code. Press COMMAND.
Note: Changing a user code does not change the user number.
7. The dispaly then shows the current user name. Press any top row key to clear. See the Entering Custom Names section in the Appendix to enter a new name.
8.
Areas systems only
(# = area number). Add or remove access to one or more areas by pressing the corresponding number keys. Press COMMAND.
9. The display changes to LEVEL CUSTOM. Refer to Adding User Codes on the previous page for a description of this prompt.
10. After entering the authority level, the keypad displays USER # CHANGED for five seconds followed by USER NUMBER: -. This display allows you to enter another user number to change. Press the ARROW key twice to exit the User Menu.
- The display changes to AREAS: # # # #
☞ Browser Feature
Refer to the Appendix at the back of this guide for a diagram showing you how to use the built-in Delete or Change User Codes browser.
Schedules
User Code Level: 7 and above. Function: The Schedules function allows you to enter into the
system the times at which you normally turn your burglary protection ON and OFF each day of the week. Depending on your system’s programming, the ON time can be used to verify that the burglary protection is armed. Also, the schedule’s ON and OFF times can be used to automatically arm or disarm the burglary protection.
Schedules can also be used to restrict access to the system by users with a 1 or 2 authority level assigned to their user codes.
Your system provides you with three different types of schedules:
1. Permanent (PRM), Primary (PRI), and Secondary (SEC) schedules occur at the same time until you change or delete them.
2. Temporary (TEMP) schedules occur only once and then are cleared when they expire. These are typically used to allow someone off hours access to the premises when used with a level 1 or 2 code.
3. Output (OUT) schedules allow you to set the times when relay outputs connected to your system turn on and off automatically.
Setting an Arming and Disarming Schedule
1. Access the User Menu and press COMMAND until SCHEDULES? displays. Press any SELECT key.
2. The keypad displays PRM TMP OUT (or PRI SEC OUT). Press the SELECT key under PRM (or PRI). This will allow you to enter a schedule that remains in place until you change or delete it.
3. The keypad displays SUN MON TUE WED. Press the COMMAND key to display THU FRI SAT. Press the SELECT key under the day you want the schedule to begin.
Note: After selecting the day of the week for the schedule to begin,
the keypad displays any currently programmed Opening and Closing times previously set for that day. This feature allows you to review programmed schedules at any time.
4. If Opening and Closing times are displayed, the keypad then displays DELETE KEEP. Press the SELECT key under DELETE to enter new times.
5. The keypad then displays OPENING TIME? followed by the display MON – : AM PM. Enter the new opening time and select AM or PM.
Enter all schedule times using a 12 hour clock. For example, to enter 6 AM you would enter a 0 + 6 + 0 + 0 and press the SELECT key under AM.
The keypad then displays CLOSING TIME? followed by the
display MON – : AM PM. Enter the new closing time and select AM or PM. Press the SELECT key under the day MON (whichever day is displayed) allows you to scroll through the days of the week and create a schedule window that spans multiple days.
Note: You must enter an Opening
will not recognize the schedule. The new schedule is now part of your system.
6. The keypad goes back to the SUN MON TUE WED display allowing you to enter another schedule.
7. To clear a schedule, press DELETE and then AM when the opening time is requested.
Press the ARROW key to exit the User Menu.
and
Closing time or the system
User Menu
23
Schedules
User Code Level: 7 and above. Function: The Schedules function allows you to enter into the
system the times at which you normally turn your burglary protection ON and OFF each day of the week. Depending on your system’s programming, the ON time can be used to verify that the burglary protection is armed. Also, the schedule’s ON and OFF times can be used to automatically arm or disarm the burglary protection.
Schedules can also be used to restrict access to the system by users with a 1 or 2 authority level assigned to their user codes.
Your system provides you with three different types of schedules:
1. Permanent (PRM), Primary (PRI), and Secondary (SEC) schedules occur at the same time until you change or delete them.
2. Temporary (TEMP) schedules occur only once and then are cleared when they expire. These are typically used to allow someone off hours access to the premises when used with a level 1 or 2 code.
3. Output (OUT) schedules allow you to set the times when relay outputs connected to your system turn on and off automatically.
Setting an Arming and Disarming Schedule
1. Access the User Menu and press COMMAND until SCHEDULES? displays. Press any SELECT key.
2. The keypad displays PRM TMP OUT (or PRI SEC OUT). Press the SELECT key under PRM (or PRI). This will allow you to enter a schedule that remains in place until you change or delete it.
3. The keypad displays SUN MON TUE WED. Press the COMMAND key to display THU FRI SAT. Press the SELECT key under the day you want the schedule to begin.
Note: After selecting the day of the week for the schedule to begin,
the keypad displays any currently programmed Opening and Closing times previously set for that day. This feature allows you to review programmed schedules at any time.
4. If Opening and Closing times are displayed, the keypad then displays DELETE KEEP. Press the SELECT key under DELETE to enter new times.
5. The keypad then displays OPENING TIME? followed by the display MON – : AM PM. Enter the new opening time and select AM or PM.
Enter all schedule times using a 12 hour clock. For example, to enter 6 AM you would enter a 0 + 6 + 0 + 0 and press the SELECT key under AM.
The keypad then displays CLOSING TIME? followed by the
display MON – : AM PM. Enter the new closing time and select AM or PM. Pressing the SELECT key under the day MON (whichever day is displayed) allows you to scroll through the days of the week and create a schedule window that spans multiple days.
Note: You must enter an Opening
will not recognize the schedule. The new schedule is now part of your system.
6. The keypad goes back to the SUN MON TUE WED display allowing you to enter another schedule.
7. To clear a schedule, press DELETE and then AM when the opening time is requested.
Press the ARROW key to exit the User Menu.
and
Closing time or the system
User Menu
23
Schedules continued
Area Schedules
Your system may be programmed for Area schedules that allows you to set a separate schedule for each area of the system. If so, after selecting the schedule type (PRM, PRI, SEC, or TMP) the keypad displays AREA NO: –. Enter the number of the area you want to enter schedules. Press COMMAND to continue.
You can also press either of the two left SELECT keys to browse through a list of the areas. Press COMMAND when the area name you want is displayed.
All/Perimeter or Home/Away systems:
programmed for Area schedules that allows you to set a separate schedule for just the perimeter or interior of the system. If so, after selecting the schedule type (PRM, PRI, SEC, or TMP) the keypad displays INT PERIM. Press the SELECT key under INT to program a schedule for just the interior of your system. Press the SELECT key under PERIM to program a schedule for just the perimeter.
Your system may be
Extending Schedules
User Code Level: 6 and above.
Depending on your system’s programming, when the schedule expires (the ON time) you can extend the schedule to a later time. The keypad buzzer sounds and the keypad displays “area name” and LATE or CLOSING TIME!. This reminds users still on the premises to arm the system or extend the schedule.
To extend the system’s schedule:
1. Press any SELECT key and the keypad will display ENTER CODE:-.
2. Enter your code and press COMMAND. The system’s schedule is automatically extended one hour.
3. The keypad then displays -: AM PM. You can enter a time to extend the schedule for greater than one hour. Press AM or PM.
Note: If the system is not armed, or the schedule extended, a
report is sent to the central station.
24
User Menu
Schedules continued
Area Schedules
Your system may be programmed for Area schedules that allows you to set a separate schedule for each area of the system. If so, after selecting the schedule type (PRM, PRI, SEC, or TMP) the keypad displays AREA NO: –. Enter the number of the area you want to enter schedules. Press COMMAND to continue.
You can also press either of the two left SELECT keys to browse through a list of the areas. Press COMMAND when the area name iyou want is displayed.
All/Perimeter or Home/Away systems:
programmed for Area schedules that allows you to set a separate schedule for just the perimeter or interior of the system. If so, after selecting the schedule type (PRM, PRI, SEC, or TMP) the keypad displays INT PERIM. Press the SELECT key under INT to program a schedule for just the interior of your system. Press the SELECT key under PERIM to program a schedule for just the perimeter.
Your system may be
Extending Schedules
User Code Level: 6 and above.
Depending on your system’s programming, when the schedule expires (the ON time) you can extend the schedule to a later time. The keypad buzzer sounds and the keypad displays “area name” and LATE or CLOSING TIME!. This reminds users still on the premises to arm the system or extend the schedule.
To extend the system’s schedule:
1. Press any SELECT key and the keypad will display ENTER CODE:-.
2. Enter your code and press COMMAND. The system’s schedule is automatically extended one hour.
3. The keypad then displays -: AM PM. You can enter a time to extend the schedule for greater than one hour. Press AM or PM.
Note: If the system is not armed, or the schedule extended, a
report is sent to the central station.
24
User Menu
Relay Output Schedules
The Schedules function allows you to set up to 50 different scheduled times for relays connected to your system to turn on and off automatically.
Programming Output Schedules:
1. Access the User Menu.
2. Press COMMAND until SCHEDULES? displays.
3. Press any SELECT key. The keypad displays PRI TMP OUT or (PRI SEC OUT). Press the SELECT key under OUT.
4. At the OUTPUT NO: – display, enter the relay output number you want to program. Press the COMMAND key.
If adding a schedule and all 50 are currently in use, you'll see an OUT SCHEDS FULL on the display. You must then delete or change an existing schedule.
5. The keypad displays SUN MON TUE WED. Press the COMMAND key to display THU FRI SAT.
6. Press the SELECT key under the day you want to program.
Note: After selecting the day of the week for the schedule to occur, the keypad displays any currently programmed On Off times previously set for that day. This feature allows you to review programmed schedules at any time.
7. If On Off times are displayed, the keypad then displays DELETE KEEP. Press the SELECT key under DELETE to enter new times.
8. The keypad then displays ON TIME?. This is followed by the display – : AM PM.
Enter a new relay On time and select AM or PM. The display changes to OFF TIME?. This is followed by the
display – : AM PM. Enter a new Off time for the relay. Enter all schedule times using a 12 hour clock. For example, to
enter 6 AM you would enter a 0 + 6 + 0 + 0 and press the SELECT key under AM. For 11 PM you would enter a 1 + 1 + 0 + 0 and press the SELECT key under PM.
9. The keypad then goes back to the day of the week displays allowing you to enter another Output schedule. To exit the user menu or to go back to the PRI TMP OUT display, press the ARROW key.
10. To clear a schedule, press DELETE and then AM when the opening time is requested.
List your Opening and Closing schedules in the table provided on the following page for easy reference.
Relay Output Schedules
The Schedules function allows you to set up to 50 different scheduled times for relays connected to your system to turn on and off automatically.
Programming Output Schedules:
1. Access the User Menu.
2. Press COMMAND until SCHEDULES? displays.
3. Press any SELECT key. The keypad displays PRI TMP OUT or (PRI SEC OUT). Press the SELECT key under OUT.
4. At the OUTPUT NO: – display, enter the relay output number you want to program. Press the COMMAND key.
If adding a schedule and all 50 are currently in use, you'll see an OUT SCHEDS FULL on the display. You must then delete or change an existing schedule.
5. The keypad displays SUN MON TUE WED. Press the COMMAND key to display THU FRI SAT.
6. Press the SELECT key under the day you want to program.
Note: After selecting the day of the week for the schedule to occur, the keypad displays any currently programmed On Off times previously set for that day. This feature allows you to review programmed schedules at any time.
User Menu
7. If On Off times are displayed, the keypad then displays DELETE KEEP. Press the SELECT key under DELETE to enter new
times.
8. The keypad then displays ON TIME?. This is followed by the display – : AM PM.
Enter a new relay On time and select AM or PM. The display changes to OFF TIME?. This is followed by the
display – : AM PM. Enter a new Off time for the relay. Enter all schedule times using a 12 hour clock. For example, to
enter 6 AM you would enter a 0 + 6 + 0 + 0 and press the SELECT key under AM. For 11 PM you would enter a 1 + 1 + 0 + 0 and press the SELECT key under PM.
9. The keypad then goes back to the day of the week displays allowing you to enter another Output schedule. To exit the user menu or to go back to the PRI TMP OUT display, press the ARROW key.
10. To clear a schedule, press DELETE and then AM when the opening time is requested.
List your Opening and Closing schedules in the table provided on the following page for easy reference.
25
User Menu
25
Schedules continued
Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim
Arm/Disarm Schedules
Area # __ , or Int or Perim Area # __ , or Int or Perim
Output # __
Output # __
Output # __
Output # __
Output # __
Output Schedules
Output # __
2626User Menu
PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff
Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing
Sun Mon Tue Wed Thu Fri Sat
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
Suggestion
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: Photocopy this page before using.
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
Schedules continued
Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim Area # __ , or Int or Perim
Arm/Disarm Schedules
Area # __ , or Int or Perim Area # __ , or Int or Perim
Output # __
Output # __
Output # __
Output # __
Output # __
Output Schedules
Output # __
User Menu
PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC PRM - PRI TMP - SEC Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff Description _________OnOff
Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing Opening Closing
Sun Mon Tue Wed Thu Fri Sat
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
Suggestion
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: Photocopy this page before using.
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
: _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M : _ M
Setting the Date and Time
User Code Level: 8 and above. Function: Allows you to change the current date and time displayed
on the Security Command keypad and used by the system to log events in its Event Memory program, and control schedules.
Setting the System’s Date and Time
1. Access the User Menu.
2. Press COMMAND until TIME? displays.
3. The keypad displays the current day and time. Press the COMMAND key. The keypad displays the current date. Press the COMMAND key to make any changes.
4. The keypad displays TIME DAY DATE.
5. Press the SELECT key under TIME to change the time. The keypad displays – : AM PM. Enter the current time and select AM or PM.
The display changes back to TIME DAY DATE.
6. Press the SELECT key under DAY to change the day of week. The keypad displays SUN MON TUE WED. If the current day of the week is not displayed, press the COMMAND key.
7. The keypad displays THU FRI SAT. Press the SELECT key under the correct day. You can use the ARROW key to toggle between the two day of the week displays.
8. Press the SELECT key under DATE to change the date. The keypad displays
MONTH:- Enter one or two digits for the month.
Press COMMAND.
DAY:- Enter up to two digits for the day.
Press COMMAND.
YEAR:- Enter up to two digits for the year.
Press COMMAND.
The display returns to the TIME DAY DATE display. Press the ARROW key to exit the User Menu.
Note: The date and time portion of the Security Command System
is year 2000 compliant.
Setting the Date and Time
User Code Level: 8 and above. Function: Allows you to change the current date and time displayed
on the Security Command keypad and used by the system to log events in its Event Memory program, and control schedules.
Setting the System’s Date and Time
1. Access the User Menu.
2. Press COMMAND until TIME? displays.
3. The keypad displays the current day and time. Press the COMMAND key. The keypad displays the current date. Press the COMMAND key to make any changes.
4. The keypad displays TIME DAY DATE.
5. Press the SELECT key under TIME to change the time. The keypad displays – : AM PM. Enter the current time and select AM or PM.
The display changes back to TIME DAY DATE.
6. Press the SELECT key under DAY to change the day of week. The keypad displays SUN MON TUE WED. If the current day of the week is not displayed, press the COMMAND key.
7. The keypad displays THU FRI SAT. Press the SELECT key under the correct day. You can use the ARROW key to toggle between the two day of the week displays.
User Menu
8. Press the SELECT key under DATE to change the date. The keypad displays
MONTH:- Enter one or two digits for the month.
Press COMMAND.
DAY:- Enter up to two digits for the day.
Press COMMAND.
YEAR:- Enter up to two digits for the year.
Press COMMAND.
The display returns to the TIME DAY DATE display. Press the ARROW key to exit the User Menu.
Note: The date and time portion of the Security Command System
is year 2000 compliant.
27
User Menu
27
Display Events
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Allows you to review up to 200 past system events.
There are six event types:
Zone Activity - Zone alarms, troubles, and restorals. Opening and Closing - Arming and disarming of the system. User Code Changes - Adding, deleting, and changing user codes. Schedule Changes - Adding, deleting, and changing schedules. Door Access - Each door access function used at a keypad. Supervisory - Problems with the system’s hardware components.
The system’s memory can hold a maximum of 200 events for 45 days. Any event older than 45 days is cleared automatically by the system. Also, once the full 200 events are stored, any new event causes the oldest event to be cleared.
Using the Display Events
1. Access the User Menu.
2. Press the COMMAND key until DISPLAY EVENTS? displays. Press any SELECT key.
3. The keypad displays FRST LST PRT SRT. Select FRST (first) to view the oldest to newest events. Select LST (last) to view the newest to oldest events. If you select FIRST, use the COMMAND key to scroll up through the events. If you select
LAST, use the ARROW key to scroll down through the events.
28
User Menu
ARROW key
SELECT keys
POWER
JONES RESIDENCE FR I 2 : 51 AM
1234
A BC
5678
90
YZ
COMMAND key
G H I J KL
D E F
COMMAND
Select PRT (print) to print the complete Display Events log. Select SRT (sort) to sort through the Display Events log and
collect information specific to a user or system event.
4. To use the Sort feature, press the SELECT key under SRT. The keypad displays FRST DATE: 8/21. Press any SELECT key and enter a 4-digit beginning date for the sort. Press COMMAND.
5. The keypad displays LAST DATE: 10/17. Press any SELECT key and enter a 4-digit ending date for the sort. Press COMMAND.
6. The keypad displays USER NUMBER: -. To sort events for a particular user, enter their user number or press COMMAND to sort for all users. To search for a user, press any SELECT key then use the COMMAND and ARROW keys to browse through the user names in the system. When the user you want is displayed, press any SELECT key then press COMMAND.
7. The keypad next displays five event types that you can include in the sort. Press the
right
SELECT key to display YES as the
event type name is displayed on the keypad. Press COMMAND.
VW XMNO P Q R ST U
The following are the five sort event types:
ACCESSES = door accesses granted.
DOOR NUMBER = leave blank for all doors. ZONE EVENTS = zone alarms, troubles, and restorals. ARM/DISARM = arming and disarming events. USER EVENTS = adding, deleting, and changing user codes. SUPERVISORY = system hardware problems.
8. After the last event type is displayed, the keypad again displays FRST LST PRT SRT. At this point, you can view or print the new sorted Display Events or press SRT for a new sort.
Display Events
User Code Level: 1 and 2 - During schedules only. 3 to 9 - Anytime. Function: Allows you to review up to 200 past system events.
There are six event types:
Zone Activity - Zone alarms, troubles, and restorals. Opening and Closing - Arming and disarming of the system. User Code Changes - Adding, deleting, and changing user codes. Schedule Changes - Adding, deleting, and changing schedules. Door Access - Each door access function used at a keypad. Supervisory - Problems with the system’s hardware components.
The system’s memory can hold a maximum of 200 events for 45 days. Any event older than 45 days is cleared automatically by the system. Also, once the full 200 events are stored, any new event causes the oldest event to be cleared.
Using the Display Events
1. Access the User Menu.
2. Press the COMMAND key until DISPLAY EVENTS? displays. Press any SELECT key.
3. The keypad displays FRST LST PRT SRT. Select FRST (first) to view the oldest to newest events. Select LST (last) to view the newest to oldest events. If you select FIRST, use the COMMAND key to scroll up through the events. If you select LAST, use the ARROW key to scroll down through the events.
User Menu
28
ARROW key
SELECT keys
POWER
JONES RESIDENCE FR I 2 : 51 AM
1234
A BC
5678
90
YZ
COMMAND key
G H I JK L
D E F
COMMAND
Select PRT (print) to print the complete Display Events log. Select SRT (sort) to sort through the Display Events log and
collect information specific to a user or system event.
4. To use the Sort feature, press the SELECT key under SRT. The keypad displays FRST DATE: 8/21. Press any SELECT key and enter a 4-digit beginning date for the sort. Press COMMAND.
5. The keypad displays LAST DATE: 10/17. Press any SELECT key and enter a 4-digit ending date for the sort. Press COMMAND.
6. The keypad displays USER NUMBER: -. To sort events for a particular user, enter their user number or press COMMAND to sort for all users. To search for a user, press any SELECT key then use the COMMAND and ARROW keys to browse through the user names in the system. When the user you want is displayed, press any SELECT key then press COMMAND.
7. The keypad next displays five event types that you can include in the sort. Press the
right
SELECT key to display YES as the
event type name is displayed on the keypad. Press COMMAND.
VW XMNO P Q R ST U
The following are the five sort event types:
ACCESSES = door accesses granted.
DOOR NUMBER = leave blank for all doors. ZONE EVENTS = zone alarms, troubles, and restorals. ARM/DISARM = arming and disarming events. USER EVENTS = adding, deleting, and changing user codes. SUPERVISORY = system hardware problems.
8. After the last event type is displayed, the keypad again displays FRST LST PRT SRT. At this point, you can view or print the new sorted Display Events or press SRT for a new sort.
About the Display Events Section
This section of the user’s guide shows the User's Guide Display Events items for both 16-character (single line) and 32-character keypad displays. While in the Display Events function, use the COMMAND and ARROW keys to go forward or backward through the list of events.
Arming and Disarming Event Displays
This displays any arming or disarming of system areas.
16-Character Display Description
ARM 3 12 1017 Area 3 was armed by user 12 on Oct. 17.
Press the SELECT key under 3 for the area name, under 12 for the user name, or under 1017 for the time the arming occurred.
32-Character Display Description
ARM 5:10P 10 / 17 The Perimeter was armed at 5:10
PERIMETER Press any Select key to display the area
number and user number then any Select key to display the user name.
Arming Event Types - There are 2 event type you may see here:
ARM - User armed the system DIS - User disarmed the system
PM.
Zone Event Displays
This section displays alarms, troubles, and other events that could occur on your protection zones.
16-Character Display Description
2 BURG ALR 1017 A burglary alarm occurred on zone 2.
Press the the alarm occurred.
32-Character Display Description
ALR 10: 23P 10/17 An alarm occurred at 10:23 BASEMENT DOOR Press any SELECT key to see the zone
number and zone type.
Zone Type - There are 7 possible zone types you may see here.
FIRE - Fire PANC - Panic BURG - Burglary EMRG - Emergency SUPV - Supervisory AUX1 - Auxiliary 1 AUX2 - Auxiliary 2
Event Types - There are 6 event types you may see here:
ALR - Alarm TBL - Trouble RST - Restore LOW - Low battery MIS - Missing wireless transmitter
Note: LOW and MIS are for wireless systems only.
right
SELECT key for the time
PM on Oct. 17.
About the Display Events Section
This section of the user’s guide shows the User's Guide Display Events items for both 16-character (single line) and 32-character keypad displays. While in the Display Events function, use the COMMAND and ARROW keys to go forward or backward through the list of events.
Arming and Disarming Event Displays
This displays any arming or disarming of system areas.
16-Character Display Description
ARM 3 12 1017 Area 3 was armed by user 12 on Oct. 17.
Press the Select key under 3 for the area name, under 12 for the user name, or under 1017 for the time the arming occurred.
32-Character Display Description
ARM 5:10P 10/ 17 The Perimeter was armed at 5:10
PERIMETER Press any Select key to display the area
number and user number then any Select key to display the user name.
Arming Event Types - There are 2 event type you may see here:
ARM - User armed the system DIS - User disarmed the system
PM.
User Menu
29
Zone Event Displays
This section displays alarms, troubles, and other events that could occur on your protection zones.
16-Character Display Description
2 BURG ALR 1017 A burglary alarm occurred on zone 2.
Press the alarm occurred.
32-Character Display Description
ALR 10: 23P 10/17 An alarm occurred at 10:23 BASEMENT DOOR Press any Select key to see the zone
number and zone type.
Zone Type - There are 7 possible zone types you may see here.
FIRE - Fire PANC - Panic BURG - Burglary EMRG - Emergency SUPV - Supervisory AUX1 - Auxiliary 1 AUX2 - Auxiliary 2
Event Types - There are 6 event type you may see here:
ALR - Alarm TBL - Trouble RST - Restore LOW - Low battery MIS - Missing wireless transmitter
Note: LOW and MIS are for wireless systems only.
right
Select key for the time the
PM on Oct. 17.
User Menu
29
User Code Change Event Displays
This displays any addition, deletion, or change to a user code.
16-Character Display Description
12 ADD 19 1017 User 12 added user 19 on Oct. 17. Press
the
right
SELECT key for the time this
occurred.
System Monitor Event Displays
This displays any problems with the system's AC power, battery, or phone line(s) or any opening of a tampered panel box.
16-Character Display Description
POWER TBL 1017 An AC failure occurred on Oct. 17. Press
the SELECT key under 1017 for the time.
32-Character Display Description
ADD 11: 41A 10 / 17 User 19 added by user 12 at 11:41 US:19 BY US:12 Press the Select key under either user
(US:) number for the user name.
User Code Event Types - There are 3 event types you may see here:
ADD - User added DEL - User deleted CHG - User code or authority level has been changed.
AM.
Supervisory Event Displays
This displays the date and time of an automatic test report.
16-Character Display Description
AUTO RECALL 1017 The test report was sent on Oct. 17.
32-Character Display Description
MSG 11: 58P 10 / 17 The test report was sent to the central AUTO RECALL station at the date and time shown.
30
User Menu
32-Character Display Description
TBL 11:41A 10/17 An AC failure occurred on Oct. 17. Press POWER the SELECT key under 1017 for the time
the failure occurred.
System Monitor Event Types - There are 2 event types:
TBL - Trouble RST - Restore
System Monitor Event Names - There are 5 system monitors:
POWER - AC power to panel BATTERY - On panel LINE 1 - Phone line number 1 LINE 2 - Phone line number 2 TAMPER - On panel box
User Code Change Event Displays
This displays any addition, deletion, or change to a user code.
16-Character Display Description
12 ADD 19 1017 User 12 added user 19 on Oct. 17.
Press the this occurred.
32-Character Display Description
ADD 11: 41A 10 / 17 User 19 added by user 12 at 11:41 US:19 BY US:12 Press the Select key under either user
(US:) number for the user name.
User Code Event Types - There are 3 event type you may see here:
ADD - User added DEL - User deleted CHG - User code or authority level has been changed.
right
Select key for the time
AM.
Supervisory Event Displays
This displays the date and time of an automatic test report.
16-Character Display Description
AUTO RECALL 1017 The test report was sent on Oct. 17.
System Monitor Event Displays
This displays any problems with the system's AC power, battery, or phone line(s) or any opening of a tampered panel box.
16-Character Display Description
POWER TBL 1017 An AC failure occurred on Oct. 17. Press
the Select key under 1017 for the time.
32-Character Display Description
TBL 11:41A 10/17 An AC failure occurred on Oct. 17. Press POWER the Select key under 1017 for the time
the failure occurred.
System Monitor Event Types - There are 2 event types:
TBL - Trouble RST - Restore
System Monitor Event Names - There are 5 system monitors:
POWER - AC power to panel BATTERY - On panel LINE 1 - Phone line number 1 LINE 2 - Phone line number 2 TAMPER - On panel box
32-Character Display Description
MSG 11: 58P 10 / 17 The test report was sent to the central AUTO RECALL station at the date and time shown.
User Menu
30
Door Access Event Displays
This displays the keypad address where a *Door Access occurred and the user number of the person granted access.
16-Character Display Description
DOOR 3 024 1017 Door (keypad) #3 was accessed by
user 24 on Oct. 17. Press the SELECT key under 1017 for the time of occurrence or under 024 for the user name.
Schedule Change Event Displays
This displays Changes made to the system’s schedules.
16-Character Display Description
PRM MON 024 1017 A Permanent schedule for Monday was
changed by user 24 on Oct. 17. Press the SELECT key under 1017 for the time of occurrence or under 024 for the user name.
32-Character Display Description
ACC 5:18P 10/17 Door (keypad) #3 was accessed by DOOR 3 USER:024 user 24 on Oct. 17. Press the SELECT
key under 1017 for the time of occurrence or under 024 for the user name.
About Door Access
Door Access is a feature available only on certain Security Command keypads that contain a built-in door releasing relay. When low voltage power for an electric door strike or magnetic lock is connected to the relay’s contacts, users entering a valid user code can release the lock and gain access to the protected area.
The Display Events feature logs the user number and name of the person granted access, the date and time, and from which keypad they entered their code.
Door Access Event Displays
This displays the keypad address where a *Door Access occurred and the user number of the person granted access.
16-Character Display Description
DOOR 3 024 1017 Door (keypad) #3 was accessed by
user 24 on Oct. 17. Press the Select key under 1017 for the time of occurrence or under 024 for the user name.
32-Character Display Description
PRM 9:41A 10/17 A Permanent schedule for Monday was SCH MON USER:024 changed by user 24 on Oct. 17.
Schedule Types - There are 4 possible schedule types:
PRM - Permanent TMP - Temporary PRI - Primary SEC - Secondary
MON - This is the day of the week in which the schedule change
occurred. The days are displayed using three letters. Press the SELECT key under the day of the week to display the scheduled Opening time and once again for the scheduled Closing time.
024 - User number of the person who made the change. Press the SELECT key under this number to display the user's name.
User Menu
31
Schedule Change Event Displays
This displays Changes made to the system’s schedules.
16-Character Display Description
PRM MON 024 1017 A Permanent schedule for Monday was
changed by user 24 on Oct. 17. Press the Select key under 1017 for the time of occurrence or under 024 for the user name.
32-Character Display Description
ACC 5:18P 10/17 Door (keypad) #3 was accessed by DOOR 3 USER:024 user 24 on Oct. 17. Press the Select key
under 1017 for the time of occurrence or under 024 for the user name.
About Door Access
Door Access is a feature available only on certain Security Command keypads that contain a built-in door releasing relay. When low voltage power for an electric door strike or magnetic lock is connected to the relay’s contacts, only users entering a valid user code can release the lock and gain access to the protected area.
The Display Events feature logs the user number and name of the person granted access, the date and time, and from which keypad they entered their code.
32-Character Display Description
PRM 9:41A 10/17 A Permanent schedule for Monday was SCH MON USER:024 changed by user 24 on Oct. 17.
Schedule Types - There are 4 possible schedule types:
PRM - Permanent TMP - Temporary PRI - Primary SEC - Secondary
MON - This is the day of the week in which the schedule change
occurred. The days are displayed using three letters. Press the SELECT key under the day of the week to display the scheduled Opening time and once again for the scheduled Closing time.
024 - User number of the person who made the change. Press the SELECT key under this number to display the user's name.
User Menu
31
Zone Bypass Event Displays
This displays the bypassing of system zones.
16-Character Display Description
26 BYPS 12 1017 Zone 26 bypassed by user 12. Press the
left
SELECT key for the zone name and
the
right
SELECT key for the time.
32-Character Display Description
BYP 5:18P 10 / 17 The east window zone was bypassed. EAST WINDOW Press a SELECT key for the zone
number and user number. Press again for the user name.
Bypass Event Types - There are 4 event types:
BYP - Bypass RST - Restore FRC - Force Arm FLT - Zone Fault
Note: You may sometimes see the user as SWG. This is short for
Swinger Bypass, which is an automatic function that allows the system to bypass a zone.
SERVICE REQUEST?
This feature of the User Menu allows you to just press any top row SELECT key while SERVICE REQUEST? is displayed and have the system automatically send a "Request for Service" message to the central station. The display changes to REQUEST MADE momentarily to confirm your request was sent.
Our service department will then contact you to arrange a service appointment.
32
User Menu
Zone Bypass Event Displays
This displays the bypassing of system zones.
16-Character Display Description
26 BYPS 12 1017 Zone 26 bypassed by user 12. Press the
left
Select key for the zone name and
the
right
Select key for the time.
32-Character Display Description
BYP 5:18P 10 / 17 The east window zone was bypassed. EAST WINDOW Press a Select key for the zone number
and user number. Press again for the user name.
Bypass Event Types - There are 4 event types:
BYP - Bypass RST - Restore FRC - Force Arm FLT - Zone Fault
Note: You may sometimes see the user as SWG. This is short for
Swinger Bypass which is an automatic function that allows the system to bypass a zone.
SERVICE REQUEST?
This feature of the User Menu allows you to just press any top row SELECT key while SERVICE REQUEST? is displayed and have the system automatically send a "Request for Service" message to the central station. The display changes to REQUEST MADE momentarily to confirm your request was sent.
Our service department will then contact you to arrange a service appointment.
User Menu
32
System Setup
We've provided this System Setup section to allow you to track the current and future status of the programmable options on your Security Command system. If you make changes to the system, you should update the information contained on these pages.
Your system is monitored by a central station.
❏ Yes ❏ No C/S Name: Address: City/State: Emergency Phone: Service Phone: Service Manager:
Your system sends Opening and Closing reports.
❏ Yes ❏ No
Your system sends Zone Bypass reports.
❏ Yes ❏ No
Your system sends Ambush reports.
❏ Yes ❏ No
Security Command keypads
Address Locations
1 2 3 4 5 6 7 8
Which keypads display System Status?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
Which keypads display Armed Status?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
Which keypads provide Door Access reports?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
System Setup
We've provided this System Setup section to allow you to track the current and future status of the programmable options on your Security Command system. If you make changes to the system, you should update the information contained on these pages.
Your system is monitored by a central station.
❏ Yes ❏ No C/S Name: Address: City/State: Emergency Phone: Service Phone: Service Manager:
Your system sends Opening and Closing reports.
❏ Yes ❏ No
Your system sends Zone Bypass reports.
❏ Yes ❏ No
Your system sends Ambush reports.
❏ Yes ❏ No
System Setup
33
Security Command keypads
Address Locations
1 2 3 4 5 6 7 8
Which keypads display System Status?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
Which keypads display Armed Status?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
Which keypads provide Door Access reports?
❏ 1 ❏ 2 ❏ 3 ❏ 4 ❏ 5 ❏ 6 ❏ 7 ❏ 8 ❏ N/A
System Setup
33
Area names and numbers
If you have an area system where your system is divided into up to eight separate areas, each area can have a custom name or description that displays at the keypad. This can help you easily track events when they occur elsewhere in your system.
Area Name
1 2 3 4 5 6 7 8
Schedules
Your system uses the following schedule types:
❏ Permanent and Temporary schedules ❏ Primary and Secondary schedules
Output relays
Your system has output relays that are used to control various functions within the building or around its perimeter. Below is a list of those relays and the devices they control.
Output # What it controls
Use the Output number in the User Menu when setting Output Schedules or using the Outputs On Off option to manually toggle the relays.
System Setup
34
Area names and numbers
If you have an area system where your system is divided into up to eight separate areas, each area can have a custom name or description that displays at the keypad. This can help you easily track events when they occur elsewhere in your system.
Area Name
1 2 3 4 5 6 7 8
Schedules
Your system uses the following schedule types:
❏ Permanent and Temporary schedules ❏ Primary and Secondary schedules
Output relays
Your system has output relays that are used to control various functions within the building or around its perimeter. Below is a list of those relays and the devices they control.
Output # What it controls
Use the Output number in the User Menu when setting Output Schedules or using the Outputs On Off option to manually toggle the relays.
System Setup
34
User Codes
Depending on how your system is programmed, you may have 50 to 200 user codes available. As you add new users or change current users' codes, you can keep track of their level of access to the system, and the areas in which their codes will operate.
Use the following table to track custom user codes in your system.
User Name
Custom user codes
When adding codes to the system through the User Menu, you can choose the CUSTOM option to select the specific menu items you want the user to access.
After adding the code into the keypad you'll see the LEVEL CUSTOM display. Choosing CUSTOM displays the full list of keypad menu options one at a time. A YES next to the option means it is enabled for the user. To disable the option, press the second SELECT key from the right to display NO. See below:
LEVEL CUSTOM
ARM/DIS YES
(
= press this SELECT key.
)
ARM/DIS NO
COMMAND
Press the COMMAND key to display the next menu option.
Suggestion
: Photocopy this table before using.
User #
Arm and Disarm
Alarm Silence
Sensor Reset
Door Access
Arm Areas
Outputs on/off
Zone Status
Bypass Zones
Zone Monitor
System Status
System Test User Codes
Schedules
Time
Display Events
Extend Closing
Temporary Code
Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 Area 8
System Setup
35
User Codes
Depending on how your system is programmed, you may have 50 to 200 user codes available. As you add new users or change current users' codes, you can keep track of their level of access to the system, and the areas in which their codes will operate.
Custom user codes
When adding codes to the system through the User Menu, you can choose the CUSTOM option to select the specific menu items you want the user to access.
After adding the code into the keypad you'll see the LEVEL CUSTOM display. Choosing CUSTOM displays the full list of keypad menu options one at a time. A YES next to the option means it is enabled for the user. To disable the option, press the second SELECT key from the right to display NO. See below:
LEVEL CUSTOM
ARM/DIS YES
(
ARM/DIS NO
COMMAND
Press the COMMAND key to display the next menu option.
= press this SELECT key.
)
Use the following table to track custom user codes in your system.
User Name
User #
Arm and Disarm
Alarm Silence
Sensor Reset
Door Access
Arm Areas
Outputs on/off
Zone Status
Bypass Zones
Zone Monitor
System Status
System Test User Codes
Schedules
Time
Display Events
Extend Closing
Temporary Code
Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 Area 8
Suggestion
: Photocopy this table before using.
System Setup
35
Standard User Codes
You can program user numbers from 1 to (50, 100, or 200). Use the tables provided below to track users of the system.
User User Name Level Areas of access
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
36
System Setup
User User Name Level Areas of access
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Suggestion
: Photocopy this page before using.
Standard User Codes
You can program user numbers from 1 to (50, 100, or 200). Use the tables provided below to track users of the system.
User User Name Level Areas of access
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
System Setup
36
User User Name Level Areas of access
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Suggestion
: Photocopy this page before using.
Frequently asked questions
This section of the user's guide attempts to answer questions you might have regarding the operation of your Security Command system.
Q. If I bypass an exit delay door when I arm the system, will I get an alarm if I come through it later?
A. You won't get an alarm from the door because it's bypassed but if you also walk through a motion detector or other armed door inside the premises you will get an alarm.
Q. When I arm or disarm my Area system, I get ALL? NO YES displayed. Does this mean all areas in the system?
A. Choosing YES arms or disarms all areas that are authorized for your user code.
Q. How do I create a schedule that starts at 8:00 am on Monday and ends at 5:00 PM on Friday.
A. In the days of the week display, select MON (Monday). For the OPENING TIME?, enter 0 + 8 + 0 + 0 AM. For the CLOSING TIME?,
at the MON — : AM PM display press the SELECT key under MON; this scrolls through the days of the week. Stop at the day you want the schedule to end. Next, enter 0 + 5 + 0 + 0 PM into the FRI — : AM PM closing time display. Press COMMAND. Press the ARROW key to exit the User Menu.
Q. What do I do if I want to be in the building past the scheduled closing (arming) time?
A. If your system is programmed for Closing Check, the keypad emits a steady tone after the schedule expires and displays “area name” LATE or CLOSING TIME!. During this display, pressing any SELECT key displays ENTER CODE: . Enter your user code and press COMMAND. Your schedule is automatically extended one hour.
The keypad now displays — : AM PM. Enter in the new time you want the schedule to expire and press COMMAND.
The time you enter may extend past midnight by pressing the AM key after the appropriate time has been entered.
This sets the opening time to 8:00 am Monday and the closing time to 5:00 PM Friday. You can substitute any other day or time in this example.
Frequently asked questions
This section of the user's guide attempts to answer questions you might have regarding the operation of your Security Command system.
Q. If I bypass an exit delay door when I arm the system, will I get an alarm if I come through it later?
A. You won't get an alarm from the door because it's bypassed but if you also walk through a motion detector or other armed door inside the premises you will get an alarm.
Q. When I arm or disarm my Area system, I get ALL? NO YES displayed. Does this mean all areas in the system?
A. Choosing YES arms or disarms all areas that are authorized for your user code.
Q. How do I create a schedule that starts at 8:00 am on Monday and ends at 5:00 PM on Friday.
System Setup
Q. What do I do if I want to be in the building past the scheduled closing (arming) time?
A. If your system is programmed for Closing Check, the keypad emits a steady tone after the schedule expires and displays “area name” LATE or CLOSING TIME!. During this display, pressing any SELECT key displays ENTER CODE: . Enter your user code and press COMMAND. Your schedule is automatically extended one hour.
The keypad now displays — : AM PM. Enter in the new time you want the schedule to expire and press COMMAND.
The time you enter may extend past midnight by pressing the AM key after the appropriate time has been entered.
37
A. In the days of the week display, select MON (Monday). For the OPENING TIME?, enter 0 + 8 + 0 + 0 AM. For the CLOSING TIME?,
at the MON — : AM PM display press the SELECT key under MON; this scrolls through the days of the week. Stop at the day you want the schedule to end. Next, enter 0 + 5 + 0 + 0 PM into the FRI — : AM PM closing time display. Press COMMAND. Press the ARROW key to exit the User Menu.
This sets the opening time to 8:00 am Monday and the closing time to 5:00 PM Friday. You can substitute any other day or time in this example.
System Setup
37
Zone Status Browser
Access the User Menu. Press COMMAND until ZONE
STATUS appears.
Start Here
ZONE STATUS?
Press any SELECT key then press the SELECT key under
NBR.
Press one of the left two SELECT keys to browse through the names of zones.
Press the COMMAND key to scroll through the list of all zone names.
When the correct zone name is displayed, press any SELECT key.
Verify the zone number matches the previously shown name.
The system displays one of these zone status messages:
–OKAY = the zone is normal –BYPAS = the zone is bypassed –BAD O = the zone is open –BAD S = the zone is shorted
ARM BYPS ALR NBR
ZONE NO: –
SELECT ZONE . . .
EAST DOOR
ZONE NO : 0 1 2
Press COMMAND.
EAST DOOR – OKAY
COMMAND
COMMAND
COMMAND
SELECT AREA . . .
FRONT OFFICE
24 HOUR ZONES
SELECT ZONE . . .
HALL SMOKE
ZONE NO : 0 3 4
Press COMMAND.
HALL SMOKE–OKAY
Pressing COMMAND allows you to enter another zone number.
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
COMMAND
When the area where the zone is located is displayed, press any SELECT key.
COMMAND
After all the areas are displayed, the system allows you to search through the 24 hour zones (Fire, Panic,
COMMAND
Supervisory, etc.).
COMMAND
When the correct zone name is displayed, press any SELECT key.
Verify the zone number matches the previously shown name.
COMMAND
The system displays one of these zone status messages:
–OKAY = the zone is normal –BYPAS = the zone is bypassed
COMMAND
–BAD O = the zone is open –BAD S = the zone is shorted
Appendix
38
Zone Status Browser
Access the User Menu. Press COMMAND until ZONE STATUS appears.
Press any SELECT key then press the SELECT key under
NBR.
Press one of the left two SELECT keys to browse through the names of zones.
Press the COMMAND key to scroll through the list of all zone names.
When the correct zone name is displayed, press any SELECT key.
Start Here
ZONE STATUS?
ARM BYPS ALR NBR
ZONE NO: –
SELECT ZONE . . .
EAST DOOR
COMMAND
SELECT AREA . . .
COMMAND
FRONT OFFICE
COMMAND
24 HOUR ZONES
SELECT ZONE . . .
HALL SMOKE
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
When the area where the zone is located is displayed, press any SELECT key.
After all the areas are displayed, the system allows you to search through the 24 hour zones (Fire, Panic,
COMMAND
Supervisory, etc.).
COMMAND
When the correct zone name is displayed, press any SELECT key.
38
Appendix
Verify the zone number matches the previously shown name.
The system displays one of these zone status messages:
–OKAY = the zone is normal –BYPAS = the zone is bypassed –BAD O = the zone is open –BAD S = the zone is shorted
ZONE NO : 0 1 2
Press COMMAND.
EAST DOOR – OKAY
COMMAND
COMMAND
ZONE NO : 0 3 4
Press COMMAND.
HALL SMOKE–OKAY
Pressing COMMAND allows you to enter another zone number.
Verify the zone number matches the previously shown name.
COMMAND
The system displays one of these zone status messages:
–OKAY = the zone is normal –BYPAS = the zone is bypassed
COMMAND
–BAD O = the zone is open –BAD S = the zone is shorted
Access the User Menu. Press COMMAND until BYPASS ZONES appears. Press any SELECT key.
Start Here
Bypass Zones Browser
BYPASS ZONES?
Press either of the two left SELECT keys.
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
When the area where the zone is located is displayed, press any SELECT key.
The display shows the zone number. Press the SELECT key under RST to Reset the zone. Press the SELECT key under BYP to Bypass the zone.
ZONE: – RST BYP
SELECT AREA . . .
COMMAND
FRONT OFFICE
SELECT ZONE . . .
COMMAND
EAST DOOR
ZONE:012 RST BYP
ZONE: – RST BYP
Press the COMMAND key to scroll through the list of all zone names.
When the correct zone name is displayed, press any SELECT key.
The display returns to the ZONE: prompt allowing you to enter another zone number.
Appendix
39
Access the User Menu. Press COMMAND until BYPASS ZONES appears. Press any SELECT key.
Press either of the two left SELECT keys.
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
When the area where the zone is located is displayed, press any SELECT key.
The display shows the zone number. Press the SELECT key under RST to Reset the zone. Press the SELECT key under BYP to Bypass the zone.
Start Here
BYPASS ZONES?
ZONE: – RST BYP
SELECT AREA . . .
COMMAND
FRONT OFFICE
SELECT ZONE . . .
COMMAND
EAST DOOR
ZONE:012 RST BYP
Bypass Zones Browser
Press the COMMAND key to scroll through the list of all zone names.
When the correct zone name is displayed, press any SELECT key.
ZONE: – RST BYP
The display returns to the ZONE: prompt allowing you to enter another zone number.
Appendix
39
Zone Monitor Browser
Start Here
ZONE MONITOR?
Access the User Menu. Press COMMAND until ZONE MONITOR? displays. Press any SELECT key.
40
Appendix
ALL NBR
ZONE: – ADD RMV
SELECT AREA . . .
FRONT OFFICE
SELECT ZONE . . .
The display shows the zone number.
Press the SELECT key under NBR.
Press either of the two left SELECT keys.
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
COMMAND
When the area where the zone is located is displayed, press any SELECT key.
Press the COMMAND key to scroll through the list of all zone names.
COMMAND
EAST DOOR
ZONE:012 ADD RMV
Selecting ADD puts the zone in the monitor mode.
When the correct zone name is displayed, press any SELECT key.
Selecting RMV removes the zone from the monitor mode.
Zone Monitor Browser
Start Here
ZONE MONITOR?
ALL NBR
ZONE: – ADD RMV
SELECT AREA . . .
FRONT OFFICE
SELECT ZONE . . .
The display shows the zone number.
Access the User Menu. Press COMMAND until ZONE MONITOR? displays. Press any SELECT key.
Press the SELECT key under NBR.
Press either of the two left SELECT keys.
This prompt allows you to search for a zone by area. Press the COMMAND key to scroll through the list of areas.
COMMAND
When the area where the zone is located is displayed, press any SELECT key.
Press the COMMAND key to scroll through the list of all zone names.
COMMAND
EAST DOOR
ZONE:012 ADD RMV
When the correct zone name is displayed, press any SELECT key.
40
Appendix
Selecting ADD puts the zone in the monitor mode.
Selecting RMV removes the zone from the monitor mode.
Start Here
USER CODES?
Access the User Menu. Press COMMAND until USER CODES? displays.
Add User Codes Browser
Press the SELECT key under ADD.
Enter a new user number
Enter a new user number.
USER NUMBER: 12
1243
Press COMMAND.
COMMAND
ADD DEL CHG
USER NUMBER: –
.
CODE NO: –
12 43
CODE NO: 1 2 3 4
USER 012
–
At this prompt, you can enter a new user number or scroll through the available user numbers.
View available user numbers
Press any SELECT key.
USER NUMBER: 012
COMMAND
Enter the new user code.
Verify the number and press COMMAND.
COMMAND
The default user name appears. Press any SELECT key to clear this name.
See the Entering Custom Names diagram at the end of this guide.
.
The first available user number is displayed.
Press COMMAND.
Appendix
41
Press the SELECT key under ADD.
Enter a new user number
Enter a new user number.
USER NUMBER: 12
1243
Press COMMAND.
COMMAND
Start Here
USER CODES?
ADD DEL CHG
USER NUMBER: –
.
CODE NO: –
12 43
CODE NO: 1 2 3 4
Access the User Menu. Press COMMAND until USER CODES? displays.
At this prompt, you can enter a new user number or scroll through the available user numbers.
View available user numbers
Press any SELECT key.
USER NUMBER: 012
Enter the new user code.
Verify the number and press COMMAND.
COMMAND
The first available user number is displayed.
COMMAND
Press COMMAND.
Add User Codes Browser
.
USER 012
–
The default user name appears. Press any SELECT key to clear this name.
See the Entering Custom Names diagram at the end of this guide.
Appendix
41
Delete User Codes Browser
Start Here
USER CODES?
Access the User Menu. Press the COMMAND key until USER CODES? displays.
42
Appendix
Press the SELECT key under DEL.
Enter a user number
USER NUMBER: 12
12
3
Press COMMAND.
USER 12 DELETED
ADD DEL CHG
USER NUMBER: –
.
4
COMMAND
At this prompt, you can enter a user number or scroll through the list of user names.
View current user names
.
Press any SELECT key.
MIKE JONES
KATIE SMITH
USER NUMBER: 013
The first available user name is displayed.
COMMAND
Press COMMAND.
The next available user name is displayed.
If this is the user you want to delete, press any SELECT key.
Verify the user number.
COMMAND
Press COMMAND.
USER 13 DELETED
Delete User Codes Browser
Press the SELECT key under DEL.
Enter a user number.
USER NUMBER: 12
12
Press COMMAND.
USER 12 DELETED
3
Start Here
USER CODES?
ADD DEL CHG
USER NUMBER: –
4
COMMAND
Access the User Menu. Press the COMMAND key until USER CODES? displays.
At this prompt, you can enter a user number or scroll through the list of user names.
View current user names.
Press any SELECT key.
MIKE JONES
KATIE SMITH
USER NUMBER: 013
The first available user name is displayed.
COMMAND
Press COMMAND.
The next available user name is displayed.
If this is the user you want to delete, press any SELECT key.
Verify the user number.
42
Appendix
COMMAND
USER 13 DELETED
Press COMMAND.
Start Here
USER CODES?
Change User Codes Browser
Access the User Menu. Press COMMAND until USER CODES? displays.
Press the SELECT key under CHG.
Enter a user number
USER NUMBER: 12
12
3
Press COMMAND.
CODE NO: * * * * *
Press any SELECT key to clear the present code.
CODE NO:
12
Enter a new code and press COMMAND.
3
KATIE SMITH
ADD DEL CHG
At this prompt, you can enter a user
USER NUMBER: –
number or scroll through the list of user names
View current user names
.
Press any SELECT key.
MIKE JONES
4
COMMAND
KATIE SMITH
USER NUMBER: 013
4
COMMAND
Follow the prompts to complete the code change. You can also press any SELECT key here to clear a custom user name and use the data entry keys to enter a new user name.
.
The first available user name is displayed.
COMMAND
Press COMMAND.
The next available user name is displayed.
If this is the user you want to change, press any SELECT key.
Verify the user number.
COMMAND
Press COMMAND.
Appendix
43
Press the SELECT key under CHG.
Enter a user number.
USER NUMBER: 12
12
3
Press COMMAND.
CODE NO: * * * * *
Press any SELECT key to clear the present code.
CODE NO:
12
Enter a new code and press COMMAND.
3
KATIE SMITH
Start Here
USER CODES?
ADD DEL CHG
USER NUMBER: –
4
COMMAND
4
COMMAND
Follow the prompts to complete the code change. You can also press any SELECT key here to clear a custom user name and use the data entry keys to enter a new user name.
Access the User Menu. Press COMMAND until USER CODES? displays.
At this prompt, you can enter a user number or scroll through the list of user names
View current user names.
Press any SELECT key.
MIKE JONES
KATIE SMITH
USER NUMBER: 013
Change User Codes Browser
The first available user name is displayed.
COMMAND
Press COMMAND.
The next available user name is displayed.
If this is the user you want to change, press any SELECT key.
Verify the user number.
COMMAND
Press COMMAND.
Appendix
43
Entering Custom Names
1
To enter a custom name into the keypad, you'll be using the 3 rows of number keys.
2
Under each number key are three letters.
To enter a custom name, press the number key above the letter you want to enter.
1
A B C
The nine and zero keys . . .
9
–
12 43
56 87
{
90 COMMAND
1
B
A
A
12 43
56 87
90 COMMAND
Once you've cleared the default name, the display shows just a dash on the left side.
3
With the number displayed, press the SELECT key that matches the position of the letter. See example.
C
4
Once the letter you want is displayed, press the number key above the next letter you want to enter.
You can enter up to 16 characters for each name into the keypad.
0
Appendix
44
Entering Custom Names
Y
Pressing the 9 key provides you with Y, Z, and a space that you can use between names. For example: BOB S M I T H.
1
To enter a custom name into the keypad, you'll be using the 3 rows of number keys.
1
A B C
2
Under each number key are three letters.
To enter a custom name, press the number key above the letter you want to enter.
(space)
Z
–
12 43
56 87
{
90 COMMAND
1
A
A
12 43
56 87
90 COMMAND
.
–
Pressing the 0 (zero) key provides you with a (dash), (period), (asterisk), and a (pound sign).
Once you've cleared the default name, the display shows just a dash on the left side.
#
*
3
With the number displayed, press the SELECT key that matches the position of the letter. See example.
B
C
4
Once the letter you want is displayed, press the number key above the next letter you want to enter.
You can enter up to 16 characters for each name into the keypad.
44
Appendix
The nine and zero keys . . .
9
(space)
Z
Y
Pressing the 9 key provides you with Y, Z, and a space that you can use between names. For example: BOB S M I T H.
0
.
–
Pressing the 0 (zero) key provides you with a (dash), (period), (asterisk), and a (pound sign).
#
*
Easy Entry™ User's Guide
This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command system. If your system is not currently using any access control devices, disregard this section. There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that your system requires a user code to arm and disarm the protection.
DOOR STRIKE
From the Status List, present your card to the reader. Once it is validated by the system, the Door Strike relay activates. Home/Away systems only activate the Door Strike relay when arming and disarming.
ARMING AND DISARMING AN AREA SYSTEM
Press Command. The keypad displays ARM DISARM. Press the Select key under either option. The keypad displays ENTER CODE: -. Present your card to the reader. Once it is validated by the system, all areas accessible by you arm or disarm automatically.
ABC SECURITY ARM DISARM
POWER POWER POWER
ABC SECURITY FRI 2:51 AM
POWER
While the keypad is in the Status List, present your access card.
ABC SECURITY ENTER CODE: –
The relay activates momentarily during which you must open the door.
Once you open the door, you have 30 seconds to exit and close the door before the zone 2 Soft­Shunt expires.
ABC SECURITY ALL? NO YES
Select NO to arm or disarm individual areas. Select YES, or simply wait, and the keypad will automatically arm or disarm all areas for which you are authorized.
Appendix
45
Easy Entry™ User's Guide
This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command system. If your system is not currently using any access control devices, disregard this section. There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that your system requires a user code to arm and disarm the protection.
DOOR STRIKE
From the Status List, present your card to the reader. Once it is validated by the system, the Door Strike relay activates. Home/Away systems only activate the Door Strike relay when arming and disarming.
ARMING AND DISARMING AN AREA SYSTEM
Press Command. The keypad displays ARM DISARM. Press the Select key under either option. The keypad displays ENTER CODE: -. Present your card to the reader. Once it is validated by the system, all areas accessible by you arm or disarm automatically.
ABC SECURITY ARM DISARM
POWER POWER POWER
ABC SECURITY FRI 2:51 AM
POWER
While the keypad is in the Status List, present your access card.
ABC SECURITY ENTER CODE: –
The relay activates momentarily during which you must open the door.
Once you open the door, you have 30 seconds to exit and close the door before the zone 2 Soft­Shunt expires.
ABC SECURITY ALL? NO YES
Select NO to arm or disarm individual areas. Select YES, or simply wait, and the keypad will automatically arm or disarm all areas for which you are authorized.
Appendix
45
ARMING AND DISARMING AN ALL/PERIMETER SYSTEM
ABC SECURITY FRI 2:51 AM
POWER
Press Command. The keypad displays PERIM ALL (when arming) or DISARM?. Press the Select key under the option. The keypad displays ENTER CODE: -.
PERIM ALL
DISARM?
POWER
Present your card to the reader. Once it is validated by the system, both areas arm or disarm automatically and the Door Strike relay activates.
ARMING AND DISARMING A HOME/AWAY SYSTEM
Home/Away system Arming and Disarming - Present your card to the reader. If the system
is armed, once the card is validated all areas are disarmed. If the system is disarmed when you present your card, once it is validated all areas are armed
in the AWAY mode.
or
The system arms or disarms the areas and activates the Door Strike relay.
ENTRY DELAY
Once the protected door is opened and the entry delay starts, the keypad displays ENTER CODE: -. Present your card to the reader and, once it is validated, the system disarms all areas accessible by you. Area systems provide a delay to allow selected areas only to be disarmed. See Arming and Disarming above.
Access door is
opened.
Using the access reader for user menu access
You can also use a card reader to access the User Menu when the
MENU? NO YES display is shown, and a code is requested.
46
Appendix
ARMING AND DISARMING AN ALL/PERIMETER SYSTEM
Press Command. The keypad displays PERIM ALL (when arming) or DISARM?. Press the Select key under the option. The keypad displays ENTER CODE: -.
PERIM ALL
DISARM?
POWER
Present your card to the reader. Once it is validated by the system, both areas arm or disarm automatically and the Door Strike relay activates.
ARMING AND DISARMING A HOME/AWAY SYSTEM
Home/Away system Arming and Disarming - Present your card to the reader. If the system is armed, once the card is validated all areas are disarmed.
ABC SECURITY ENTER CODE: -
POWER
or
POWER
The system disarms the areas and activates the Door Strike relay. Area systems allow a delay for you to select only certain areas. See Arming and Disarming.
The system arms or disarms the areas and activates the Door Strike relay.
ABC SECURITY FRI 2:51 AM
POWER
If the system is disarmed when you present your card, once it is validated all areas are armed in the AWAY mode.
ENTRY DELAY
Once the protected door is opened and the entry delay starts, the keypad displays ENTER CODE: -. Present your card to the reader and, once it is validated, the system disarms all areas accessible by you. Area systems provide a delay to allow selected areas only to be disarmed. See Arming and Disarming above.
Using the access reader for user menu access
You can also use a card reader to access the User Menu when the MENU? NO YES display is shown, and a code is requested.
Appendix
46
Access door is
opened.
ABC SECURITY ENTER CODE: -
POWER
The system disarms the areas and activates the Door Strike relay. Area systems allow a delay for you to select only certain areas. See Arming and Disarming.
POWER
Pager Direct™ User's Guide
Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system and know at a glance the status of your system.
Area Names
List your system's area names and numbers below:
Area Name Area Name
1_______________________ 3 ______________________
2_______________________ 4 ______________________
Service Department Phone: ______________________ Emergency Phone: _____________________________
Central Station Phone: ____________________________
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Fold
List your system's area names and numbers below:
Area Name Area Name
1_______________________ 3 ______________________
2_______________________ 4 ______________________
Service Department Phone: ______________________ Emergency Phone: _____________________________
Central Station Phone: ____________________________
Pager Direct™
Security Command Alphanumeric Paging
Cut along dotted lines
Security Command Numeric Paging
Area Names
Pager Direct™
Cut along dotted lines
Appendix
47
Pager Direct™ User's Guide
Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way as someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the system and know at a glance the status of your system.
Area Names
List your system's area names and numbers below:
Area Name Area Name
1_______________________ 3 ______________________
2_______________________ 4 ______________________
Service Department Phone: ______________________ Emergency Phone: _____________________________
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Central Station Phone: ____________________________
Fold
List your system's area names and numbers below:
Area Name Area Name
1_______________________ 3 ______________________
2_______________________ 4 ______________________
Service Department Phone: ______________________ Emergency Phone: _____________________________
Central Station Phone: ____________________________
Pager Direct™
Area Names
Pager Direct™
Security Command Alphanumeric Paging
Cut along dotted lines Cut along dotted lines
Security Command Numeric Paging
Appendix
47
Numeric Pager Display
00128–301 234
Account Number
Account Number
This number has been programmed into your Security Command system as an identifier. Whenever the system sends a message to your pager, it will always send the account number first to identify itself.
MessageIDAlways
Zero
Zone, Area, or
User Number
Account Number
Whenever the system sends a message to your pager, it will always send the account number first to identify itself. After the account, you'll see:
Typical Zone Event Display Description
20002 001 NORTHWEST DOORS BURG *ALARM* SHIPPING
Account Zone Zone Name Zone Type Event Area Name
Zone Types - BURG, FIRE, SUPV (Supervisory), PANC (Panic), EMRG (Emergency), AUX1, or AUX2 Events - ALARM or TROUBLE
Typical Arming/Disarming Display Description
20002 ARMED 0016 WILLIAM SMITH 01 EAST WAREHOUSE
Account Event User # User Name Area # Area Name
Events - ARMED or DISARMED
Message ID
This is always a single digit, 1 to 6, that describes the message sent.
1 = Zone Alarm 3 = Area(s) Arming 2 = Zone Trouble 4 = Area(s) Disarming 6 = User Checkin
Zone, Area, or User Number
If this message is for a zone, the 1 to 3 digit zone number is displayed. If this message is for areas that are being armed or disarmed, the area
numbers are shown in sequential order. Example: 1 2 4.
Security Command Numeric Paging
Appendix
48
Numeric Pager Display
00128–301 234
Account Number
Account Number
This number has been programmed into your Security Command system as an identifier. Whenever the system sends a message to your pager, it will always send the account number first to identify itself.
MessageIDAlways
Zero
Zone, Area, or
User Number
User Checkin Display Description
20002 USER CHECKIN REPORT BY 0016 BILLY JONES
Account Function Performed User # User Name
Functions - USER CHECKIN REPORT (An authorized user has selected Checkin from the User Menu)
Typical System Event Display Description
20002 LATE TO CLOSE
Account Event
Events - LATE TO CLOSE (The system has not been armed at its scheduled closing time)
ALARM CANCELLED (An alarm has been cancelled by an authorized user)
Security Command Alphanumeric Paging
Account Number
Whenever the system sends a message to your pager, it will always send the account number first to identify itself. After the account, you'll see:
Typical Zone Event Display Description
20002 001 NORTHWEST DOORS BURG *ALARM* SHIPPING
Account Zone Zone Name Zone Type Event Area Name
Zone Types - BURG, FIRE, SUPV (Supervisory), PANC (Panic), EMRG (Emergency), AUX1, or AUX2 Events - ALARM or TROUBLE
Typical Arming/Disarming Display Description
20002 ARMED 0016 WILLIAM SMITH 01 EAST WAREHOUSE
Account Event User # User Name Area # Area Name
Events - ARMED or DISARMED
Message ID
This is always a single digit, 1 to 6, that describes the message sent.
1 = Zone Alarm 3 = Area(s) Arming 2 = Zone Trouble 4 = Area(s) Disarming 6 = User Checkin
Zone, Area, or User Number
If this message is for a zone, the 1 to 3 digit zone number is displayed. If this message is for areas that are being armed or disarmed, the area
numbers are shown in sequential order. Example: 1 2 4.
Security Command Numeric Paging
Appendix
48
User Checkin Display Description
20002 USER CHECKIN REPORT BY 0016 BILLY JONES
Account Function Performed User # User Name
Functions - USER CHECKIN REPORT (An authorized user has selected Checkin from the User Menu)
Typical System Event Display Description
20002 LATE TO CLOSE
Account Event
Events - LATE TO CLOSE (The system has not been armed at its scheduled closing time)
ALARM CANCELLED (An alarm has been cancelled by an authorized user)
Security Command Alphanumeric Paging
FA100 User's Guide
These instructions guide you through the operation of your system using the FA100 Wireless Command Transmitter. The FA100 operates for the Home/Away or ALL/Perimeter arming systems.
Arming a Home/Away or ALL/Perimeter System
1. Press the HOME button to arm the Perimeter burglary protection.
2. Press the AWAY button to arm all of the burglary protection.
Disarming a Home/Away or ALL/Perimeter System
1. Press the OFF button to disarm all of the burglary protection.
Using the ALERT Button
Pressing the ALERT button sends a Panic alarm to the panel. If your system is monitored by a central station, the proper authorities will be notified of the alarm.
FA113 User's Guide
These instructions guide you through the operation of your system using the FA113 Wireless Keychain Remote.
Arming
1. Press the ON button to arm all of the burglary protection.
Disarming
1. Press the OFF button to disarm all of the burglary protection.
Using the ALERT Buttons
Press the two ALERT buttons simultaneously to send a Panic alarm to the panel. If your system is monitored by a central station, the proper authorities will be notified of the alarm.
Appendix
FA100 User's Guide
These instructions guide you through the operation of your system using the FA100 Wireless Command Transmitter. The FA100 operates for the Home/Away or ALL/Perimeter arming systems.
Arming a Home/Away or ALL/Perimeter System
1. Press the HOME button to arm the Perimeter burglary protection.
2. Press the AWAY button to arm all of the burglary protection.
Disarming a Home/Away or ALL/Perimeter System
1. Press the OFF button to disarm all of the burglary protection.
Using the ALERT Button
Pressing the ALERT button sends a Panic alarm to the panel. If your system is monitored by a central station, the proper authorities will be notified of the alarm.
FA113 User's Guide
These instructions guide you through the operation of your system using the FA113 Wireless Keychain Remote.
49
Arming
1. Press the ON button to arm all of the burglary protection.
Disarming
1. Press the OFF button to disarm all of the burglary protection.
Using the ALERT Buttons
Press the two ALERT buttons simultaneously to send a Panic alarm to the panel. If your system is monitored by a central station, the proper authorities will be notified of the alarm.
Appendix
49
Index
Alarm display 3 Ambush codes 22 Area Schedules 24 Armed Message 6 Arming
All/Perimeter mode 9, 46 Area mode 7, 45 Home/Away mode 11, 46 Instant mode 9, 11 using Easy Entry™ 45 with doors and windows open 6
Bypassing a zone 17
restoring a bypassed zone 17
zones that can't be bypassed 17 CLOSING TIME! display 23 ONE MOMENT message 6 Disarming 4
alarm display 8, 10, 12
clears alarm displays 5
during an alarm 10, 12
Easy Entry™ keypads 45
ENTER CODE display 3, 8, 10, 12
keypad display 8, 10, 12
only selected areas 8
prewarn tone 8, 10, 12
reporting to central station 8, 10, 12
Door Strike operation 45 Easy Entry™ 45 Emergency procedures ii Entry and Exit zones 5 Events held in memory
amount 28 False Alarms 1 Keypad Messages 3
ALARM CANCELLED 10, 12
BAD * 6
CLOSING TIME! 23
ONE MOMENT ... 6
INSTNT 9, 11
LOCAL ALARM ONLY 6 Keypad operation 2 Keypad tones
during a trouble condition 4
entering while armed 4
Zone Monitor tone 4 Keyswitch operation
exit delay display 6 Monitoring zones 18 Outputs
names and numbers 16, 34
turning on and off 16 Pager reporting 47
quick reference card 47
Perimeter protection 4
arming 9, 11 Power (AC) LED 2 Priority zone
BAD * condition 6 Relay (output) control 16 Resetting a smoke detector 14 Security Command keypad 1, 2 Sending reports to a Central station 5, 8, 10, 12 Sending reports to your pager 47 Sensor Reset 14
before using 14
for wireless systems 14 Silent alarm 21 System Setup 33 System status 5 Testing the system 1 Turning the system off 8, 10, 12 Turning the system on 7, 9, 11 User Codes 20
Ambush codes 21
areas 20
authority level 21, 22
deleting 22
Temporary codes 21 user number 20 user names 20
User Menu 1
accessing 13, 46 restrictions 20
Using Schedules 23
automatic arming 23 automatic disarming 23
Using the keypad 2
arrow key 2 command key 2 top row keys 2
Viewing past events 28
arming and disarming 29 system troubles 30 user code changes 30 zone alarms and troubles 29
Wireless
FA100 49 FA113 49 Keychain Remote 49 low battery displays 3
Zones 5
24 hour zones 5 bypassed 6 force armed 6
Zone Monitor 18
50
Appendix
Index
Alarm display 3 Ambush codes 22 Area Schedules 24 Armed Message 6 Arming
All/Perimeter mode 9, 46 Area mode 7, 45 Home/Away mode 11, 46 Instant mode 9, 11 using Easy Entry™ 45 with doors and windows open 6
Bypassing a zone 17
restoring a bypassed zone 17
zones that can't be bypassed 17 CLOSING TIME! display 23 ONE MOMENT message 6 Disarming 4
alarm display 8, 10, 12
clears alarm displays 5
during an alarm 10, 12
Easy Entry™ keypads 45
ENTER CODE display 3, 8, 10, 12
keypad display 8, 10, 12
only selected areas 8
prewarn tone 8, 10, 12
reporting to central station 8, 10, 12
Door Strike operation 45 Easy Entry™ 45 Emergency procedures ii Entry and Exit zones 5 Events held in memory
amount 28 False Alarms 1 Keypad Messages 3
ALARM CANCELLED 10, 12
BAD * 6
CLOSING TIME! 23
ONE MOMENT ... 6
INSTNT 9, 11
LOCAL ALARM ONLY 6 Keypad operation 2 Keypad tones
during a trouble condition 4
entering while armed 4
Zone Monitor tone 4 Keyswitch operation
exit delay display 6 Monitoring zones 18 Outputs
names and numbers 16, 34
turning on and off 16 Pager reporting 47
quick reference card 47
Perimeter protection 4
arming 9, 11 Power (AC) LED 2 Priority zone
BAD * condition 6 Relay (output) control 16 Resetting a smoke detector 14 Security Command keypad 1, 2 Sending reports to a Central station 5,
8, 10, 12 Sending reports to your pager 47 Sensor Reset 14
before using 14
for wireless systems 14 Silent alarm 21 System Setup 33 System status 5 Testing the system 1 Turning the system off 8, 10, 12 Turning the system on 7, 9, 11 User Codes 20
Ambush codes 21
areas 20
authority level 21, 22
deleting 22
Temporary codes 21 user number 20 user names 20
User Menu 1
accessing 13, 46 restrictions 20
Using Schedules 23
automatic arming 23 automatic disarming 23
Using the keypad 2
arrow key 2 command key 2 top row keys 2
Viewing past events 28
arming and disarming 29 system troubles 30 user code changes 30 zone alarms and troubles 29
Wireless
FA100 49 FA113 49 Keychain Remote 49 low battery displays 3
Zones 5
24 hour zones 5 bypassed 6 force armed 6
Zone Monitor 18
50
Appendix
LT-0287 (11/97)
LT-0287 (11/97)
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use