DMP SR3 Quick Start Guide

SR3 Bluetooth and Proximity Reader

Wire the Reader

Connect the reader wires to the access controller according to the purpose of each controller terminal. Refer
to Table 1 and the following examples for details. For wiring and power requirements, refer to “Wiring and Power”.

GET STARTED

SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
reader protocol to communicate with door controllers or access control modules.

Procedure

The installation must follow this procedure:

Step 1 (Technician): Install the reader.

Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.

Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.

Step 4 (Customer): Assign credentials to a user in Virtual Keypad.

Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad.

Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.

Quick Start Guide

This quick start guide walks you through Step 1 and Step 2. For the full installation guide, follow the QR code below.

Full Installation Guide

To view the full SR3 Installation Guide (LT-2505), scan this QR code or visit DMP.com.

Wire the Reader

WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit’s

memory and firmware, which renders the device inoperable until it is reconfigured and re-enrolled.

Disconnect power before wiring the reader. After wiring and reconnecting power, the LED turns steady yellow,
indicating that the reader is ready for enrollment. Follow these guidelines when wiring the reader: Connections must
be made in accordance with NFPA 70: Do not connect to a receptacle controlled by a switch. Minimum wire gauge is
24 AWG with a maximum single wire run length of 500 ft (150 m).

WIRE COLOR PURPOSE

Red Power (Positive) R1 1 (RED) Red

Black Ground (Negative) B1 4 (BLK) Black

White Data 1 W1 2 (WHT) White

Green Data 0 G1 3 (GRN) Green/White

Blue Green LED LC LC None

Orange Beeper BC RA None

Purple Red LED None None None

Yellow Smart Card Present None None None

TYPICAL X1 SERIES
TERMINALS

TYPICAL 734 SERIES
TERMINALS

TYPICAL KEYPAD
WIRES

STEP 2:  ENROLL & ASSOCIATE THE READER

Save

Enroll & Associate the Reader in Tech APP

A technician on site must associate each reader with a system before mobile credentials can be purchased in Dealer
Admin by an Administrator.

Note: For XR Series panels with 734 Series Access Control Modules, ensure Program 734 Options is turned on and
Card Options is set to Custom in Device Setup before proceeding.

1. Stand at the reader and ensure your device has Bluetooth turned on.

2. Open Tech APP, then fi nd and open the appropriate system.

3. Tap the Bluetooth Readers tile.

4. Tap

Add. Name the reader, then tap Create.

5. When prompted, touch your device to the reader. When paired successfully, the reader beeps.

6. In Tech APP, open the reader you added. Use the slider to adjust the Reader Range closer or farther as needed.
Range is 3in to 30ft (7.62 cm to 9.14 m).

7. To update the reader’s fi rmware, go to Firmware and tap Update. If no new fi rmware is available, this button is not
displayed.

8. Tap

.

LED Operation

LED COLOR LED BEHAVIOR MEANING

None None No power or LED not connected

Yellow Spinning Powering on

Yellow Steady Connected to power, ready for enrollment

White Steady Enrolled, waiting for credential

Blue Spinning Searching for credential

Green Flash Access Granted

Mobile Device and Software Requirements

▶ The SR3 uses BLE Version 4.2 or higher

▶ Android devices with Version 8.0 (Oreo) or higher and Bluetooth enabled

▶ iOS devices with Version 10.0 or higher and Bluetooth enabled

▶ Tech APP (Version 2.15.0 or higher) and Virtual Keypad (Version 6.35.0or higher)

▶ Compatible with Mobile Credentials and 125 kHz proximity credentials

Specifi cations

Operating Voltage 12VDC

Current Draw 100 mA typical at 12 VDC

135 to 155 mA max at 12VDC

Read Range Adjustable, range 3.0 in to 30 ft (7.62 cm to 9.14 m)

Operating Temperature -27 °F to 151 °F (-33 °C to 66 °C)

Recommended Humidity 85% RH or lower, non-condensing

IP Rating IP65

Dimensions 6.0” x 1.7” x 1.3” (15.24 cm x 4.32 cm x 3.30 cm)

18205

LT-2519 21182

© 2021

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

Domestic: 800.641.4282 | International: 417.831.9362

DMP.com