DMP 790 User Manual

USER'S GUIDE

790/793 Demonstrator Keypads

Description

The DMP 790 and 793 Demos are portable, hand held keypads that allow

123

you to demonstrate the operation of DMP 32-character LCD keypads for
sales and training presentations.

Both keypads operate in either the Area Arming, All/Perimeter, or
Home/Sleep/Away modes and simulate arming, disarming and the
following User Menu options: ALARM SILENCE, SENSOR RESET,

ARMED AREAS, ZONE MONITOR, SCHEDULES, USER
CODES, and DISPLAY EVENTS.

Demonstrating how the system disarms

In Area Arming mode, press COMMAND to display ARM DISARM.
Press the SELECT key under DISARM. The Demo displays ENTER
CODE: –. Enter any 4-digit code. The Demo displays ALL? NO YES,
select YES to disarm all four areas. Select NO to disarm selected areas.
The Demo displays the name of each area along with its area number and
a NO YES prompt. Select NO to leave the area armed and display the
next area.

In All/Perimeter and Home/Sleep/Away modes, Enter a 4-digit code.
The Demo displays ALL SYSTEM OFF.

793 Demo Features

The 793 Demo additionally contains a built-in proximity reader for
demonstrating the Easy Entry™ system. Just present the card or token
whenever the ENTER CODE: - prompt is displayed.

Powering the Demo

Your 790/793 Demo operates on a standard 9V Alkaline battery that
connects to a harness at the back of the keypad. A battery and holder are
supplied as well as some adhesive foam allowing you to attach the
battery holder directly to the back of the keypad housing. See Figure 1.

Important: Unplug the 9V battery when not in use.

Fire Zone Alarm

While the Demo is armed or disarmed, pressing the second left SELECT
key simulates a fire zone alarm. The keypad displays SMOKE
DETECTOR and sounds the alarm. To silence the alarm, enter any 4­digit code. Press the SELECT key under SILENCE if required.

To turn off the red keypad backlighting, press COMMAND key until
MENU? NO YES displays then press the SELECT key under YES.
At the ENTER CODE: prompt, enter any 4-digit code and press

COMMAND. At SENSOR RESET?, press any SELECT key.

Panic Key Alarm

To demonstrate the manual alarm capability of the LCD series keypads,
the 790/793 Demos provide an audible and visual alarm representation
of a manual Fire alarm that can be inititated by pressing and holding the
two top right SELECT keys. The Police and Emergency Panic alarms
will only produce a short beep for demonstration as these keys are used
for the Front Door and Fire Alarm activations.

Battery
Holder

Adhesive

Backed

Foam

Alkaline

9V

Battery

Figure 1: Connecting the 9V battery

Battery

Harness

Demonstrating how the system arms

In Area Arming mode, press COMMAND to display ARM DISARM.
Press the SELECT key under ARM. At ALL? NO YES, select YES
to arm all four areas. Select NO to arm selected areas. The Demo
displays the name of each area along with its area number and a NO YES
prompt. Select NO to leave the area off and display the next area.

In All/Perimeter and Home/Sleep/Away modes, press COMMAND and
select from either the PERIM ALL or HOME SLEEP AWAY options.

During the exit delay in All/Perimeter and Home/Sleep/Away modes,
press the SELECT key under INSTANT to instantly arm the areas.

Front Door Zone

While the Demo is armed, pressing the first left SELECT key simulates
a front door zone fault and starts the entry delay. After 15 seconds, the
790/793 Demo simulates a front door alarm. In the Home/Sleep/Away
and All/Perimeter modes, entering any 4-digit code displays DISARM
SILENCE. Press the SELECT key under DISARM to disarm the
keypad and silence the alarm. Press the SELECT key under SILENCE
to silence the alarm only.

In Area Arming mode, entering any 4-digit user code silences the alarm
while leaving the areas armed. To turn off the red keypad backlighting,
just disarm the system.

Menu Options

The 790/793 Demo simulates the same keypad User Menu available to
customers in actual installations. To enter the menu, press the
COMMAND key until MENU? NO YES displays then press the
Select key under YES. At the ENTER CODE: prompt, enter any 4-digit
code and press COMMAND. Once in the menu, use the COMMAND
and ARROW keys to scroll through the available options.

Alarm Silence

Simulates silencing an alarm.

Sensor Reset

Simulates resetting sensors.

Armed Areas

Displays the name of each armed area for 4 seconds.

Zone Monitor

Allows you to select all or some zones to put into the zone monitor mode.

Schedules

Simulates entering schedules into the system.

User Codes

Simulates the adding, deleting, and changing of user codes to the system.
After specifying the user level, you can also use the number keys to
demonstrate entering a custom user name into the system.

Display Events

This option displays simulated events. Refer to the panel's user's
guide for a description of the entries.

2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282

LT-0321 (12/96)

User Options Menu

The 790/793 Demos simulate the User Options Menu for adjusting the
keypad's brightness, tone, and speaker volume. On an actual installation,
these adjustments can be made by the user at any time.

To access the User Options Menu, press and hold the COMMAND and
Arrow keys for about five seconds. The display changes to:

SET BRIGHTNESS
< ■ ■ ■ ■ ■ ■ ■ ■ >

Use the top left and right SELECT keys to dim and brighten the display.
Press the COMMAND key. The display changes to:

SET TONE
< ■ ■ ■ ■ ■ ■ ■ ■ >

Use the left and right SELECT keys to set the keypad's tone.
Press the COMMAND key. The display changes to:

How to enter alpha text

To enter a new default keypad message into the keypad, you'll be using
the number keys (1 through 9) and the left three SELECT keys (number
1, 2, and 3). Under each number key are three letters. the first letter, for
example A under the number 1 key, corresponds with the number 1
SELECT key. To make the letter A appear in the display you would
press the number 1 key and then the number 1 SELECT key. To make
the letter B appear in the display you would press the press the number
1 key and then the number 2 SELECT key. To make the letter C appear
in the display you would press the number 1 key and then the number 3
SELECT key. This operation is the same for all groups of letters under
the number keys.

Press the COMMAND key to return to the Installer Options Menu. Press
the SELECT key under KPD DIAG to start the keypad diagnostics.

The first diagnostic test causes the keypad to light all the elements of the
LCD panel and the Red backlighting of the keyboard alternately. Press
the COMMAND key to continue.

The display changes to:

SET VOLUME LEVEL
< ■ ■ ■ ■ ■ ■ ■ ■ >

Use the top left and right SELECT keys to adjust the keypad's volume.

Installer Options Menu

The 790/793 Demos contain an Installer Options Menu that allows you
to customize many of the keypad's features and displays. To enter the
Installer Options Menu, press and hold the COMMAND and ARROW
keys for about five seconds. The display changes to SET BRIGHTNESS.
Enter 3577 and press COMMAND. The display changes to:

KPD KPD
OPT DIAG STOP

Press the SELECT key under KPD OPT (keypad options) to display:

SYSTEM TYPE:
*AREA A/P H/A

(the asterisk shows the current selection)

Three Operating Modes

The first option allows you set the operating mode of the keypad to either
Area Arming, All/Perimeter, or Home/Sleep/Away modes. To change
the current mode, press the SELECT key under the appropriate choice.
An asterisk appears next to your selection.

Press the COMMAND key to display:

DEFAULT KPD MSG:
790 DEMO KEYPAD

You can enter a custom message of up to 16 characters that appears on
the top line of the keypad display. This allows you to customize the
Demo with a customer's name prior to a sales or training call. To change
the default message, press any SELECT key. The current message is
cleared and a dash appears to the left. Using the letters under the number
keys, you can now enter a new default keypad message.

PRESS KEY TO
TEST

This test allows you to confirm that all the keys are in good working
order. As you press and hold a key its number appears in the display. You
can test each key except the ARROW and COMMAND keys in this
manner.

Press COMMAND to display the Zone Test Feature.

Z1 OKAY Z2 OKAY
Z3 OKAY Z4 OKAY

This feature simulates the zone test feature of the 790/793 keypads. In
an actual installation you would be able to open and close the keypad's
zones and see the change reflected here. The three different displays you
would see here are: OPEN, SHRT (short), and OKAY.

Press COMMAND to display:

INPUT WIEGAND

This simulates the display an installer would see on an Easy Entry™
keypad using access control readers. The keypad displays OKAY when
a card is read by the internal proximity reader on a 793 Demo.

Factory Programmed areas

The Area Arming, All/Perimeter, and Home/Sleep/Away modes each
contain factory programmed areas.

Area Arming

1- Northwest Office (includes the Front Door)
2- Manufacturing
3- South Warehouse
4- West Power Plant

All/Perimeter - Home/Sleep/Away

1- Perimeter (includes the Front Door)
2- Interior
3- Bedrooms (Home/Sleep/Away only)

Digital Monitoring Products

2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282