DMP 263LTE-A, 263LTE-FN, 265LTE-A, 263LTE-V, 263EXT Specification
...
DMP.COM
Digital Cellular Communicators
@DMPALARMS
263EXT
▸ Modular add-on to XTL, XT or XR
Series™ panels
▸ Direct cellular communication
enables a direct path for alarm
signals from the panel to the
monitoring station
▸ Uses digital cellular LTE data
networks from AT&T or Verizon
XTLtouch
FEATURES
▸ Plug-and-play installation
and activation of add-on
communication modules
▸ Direct reporting to any
DMP monitoring center
receiver with no relaying or
intermediary retransmission
of alarm signals
▸ Power from panel with low
current draw for long standby
battery life
▸ Fully supervised to ensure
communication
263LTE-FN
XT Series
▸ Can be equipped with local or
remote antenna
▸ Check signal strength
indication at the keypad
▸ Supports the DMP Virtual
Keypad™ app
▸ XR550E provides privacy
for your data with DMP
encryption technology
▸ XR150FC/XR550FC with 263
Series communicators have
FDNY approval for network or
cell primary communication
XR Series
▸ DMP Adaptive Technology™
switches communication
paths while maintaining
supervision if the current
path becomes unavailable on
the XR Series™ panels
▸ 263EXT Cellular Extension
Modules extend cellular reach
up to 300 feet using a single
wired connection without
losing dB strength
▸ Access to FirstNet’s high-
speed network for alarm
panel communication
(263LTE-FN)
XTLplus
CELLULAR COMMUNICATORS
PRIMARY OR BACKUP PATH
Configure your DMP digital cellular
communicator as the primary path, providing
installation flexibility and cost savings. For
commercial fire applications, the 263LTE can be
used as a stand-alone communicator without the
need for a backup.
Cellular is the right choice for locations
not easily reached by phone or land lines,
or where there are concerns that physical
communication links might be tampered with.
Your cellular communicator can also be a backup
communication path, providing the security of a
communication link that continues to function,
even when land lines are cut or compromised.
FULLY SUPERVISED
You’re kept fully informed of system status.
The unit sends full reporting messages including
Zones, Areas and Users, with all names and
details included. Full supervision ensures that
the cellular communication path is intact
and functional.
ADAPTIVE TECHNOLOGY™
If the primary communication path is
compromised or becomes unavailable, Adaptive
Technology almost instantly switches to a
designated backup path. Where multiple
backups are available, communications can
be programmed to switch to another path
as necessary. The check-in frequency and
programming for a backup path adapt to the
check-in programming of the primary path.
When the primary path becomes available,
normal communications are restored. Adaptive
Technology provides additional confidence in
the integrity of your system, while protecting you
from unexpected cellular service charges.
DIRECT DATA TRANSMISSION
The digital cellular communicators transmit IP
data packets directly from the panel’s processor
over the LTE wireless data network. All of the
messages that are capable of being sent by
the control panel are received directly by the
DMP monitoring center receiver. There are no
intermediary servers or network operation
centers, and no retransmission or reinterpretation
of the information. Direct reporting means
faster response, with no concerns about signals
not being properly relayed or intermediate
communication links failing.
CELLULAR SERVICE FLEXIBILITY
With SecureCom Wireless™ from DMP, you
have a one-stop resource for both hardware
and cellular service. DMP digital cellular
communicators, whether selected as original
equipment in a new panel or added to an existing
panel via an expansion card, are ready to use the
SecureCom service.
263LTE CELLULAR COMMUNICATORS
For existing XT/XR Series panels not originally
configured with cellular communications,
the 263 Series expansion cards let you add
cellular capabilities.
The 263LTE allows alarm messages to be
communicated to an SCS-1R or SCS-VR Receiver
over their respective HSPA+ or LTE networks. It
provides a fully supervised alarm communication
path over the network.
The 263LTE is installed in the panel enclosure
and powered by the panel so no additional
enclosure, power supply or battery backup
is needed. Plug-and-play installation makes
upgrading your panel quick and easy. The
263LTE includes an embedded SIM card for easy
activation. All modules are ready for activation
with SecureCom Wireless.
263EXT CELLULAR EXTENSION MODULES
The 263EXT comes with a module that installs
directly on the control panel inside the enclosure.
Also included is a second remote module to
install with a cell modem in the attic or wherever
signal strength is best. Between the two, you can
have up to 300 feet of continuous reach with
a CAT5 cable or 22 AWG shielded wire.
The modules communicate with each other
through a single wired connection, maintaining
cellular signal.
With DMP’s 263EXT Cellular Extension Modules,
you can extend cellular reach without losing a
single dB. The modules are compatible with
all 263 modems and with all XT and XR
Series panels.
265LTE CELLULAR COMMUNICATORS
The 265LTE cellular communicators pair with
XTLplus™ systems, whereas the 265LTE-V-Touch
plugs into the XTLtouch™. In either case, both
easily incorporate cellular communications.
In the panel plastic, it requires no additional
enclosures, power supplies, batteries, cabling or
conduit connections. The 265LTE contains LTE
technology. It includes an embedded SIM card
for easy activation. All modules are ready for
activation with SecureCom Wireless.
263LTE-FN FIRSTNET READY™ CELLULAR COMMUNICATOR
The 263LTE-FN provides wireless communication
for DMP XR Series panels and is approved for use
on FirstNet®, which is built with AT&T in a publicprivate partnership with the First Responder
Network Authority. With DMP’s FirstNet Ready
communicator, alarm companies have the
advantage of using Band 14 – the nationwide,
high-quality spectrum set aside by the federal
government specifically for FirstNet.
Alarm service companies qualify to use the
FirstNet network by first obtaining a TMA
Certificate of Verification that verifies they are
in compliance with accepted Alarm Industry
Standards. In addition to the TMA certification,
alarm service providers must enter into a
FirstNet Agreement with AT&T before they
can oer FirstNet Ready alarm panels with
FirstNet service.
Note: If using the 263LTE-FN with the XR150/
XR550 Series, a model 381 cable is required for
connection from the cell module SMA connector
to the panel enclosure knockout.
Specifications
Primary Power 12 VDC from panel
Current Draw (263LTE)
Standby 14 mA
Alarm 14 mA
Current Draw (265LTE)
Standby 13 mA
Alarm 13 mA
Ordering Information
263LTE -A/381-2 AT&T LTE Cellular Communicator, XT/XR Series
263LTE-A AT&T Cellular Communicator, XT Series
263LTE-FN AT&T FirstNet Cellular Communicator, XR
Series
265LTE-A AT&T Cellular Communicator, XTLplus
263LTE -V Verizon LTE Cellular Communicator, XT/XR Series
263EXT Cellular Extension Modules, XT/XR Series
265LTE-V Verizon LTE Cellular Communicator, XTLplus
265LTE-V-Touch Verizon LTE Cellular Communicator, XTLtouch
Accessories
381-2 18" Coax Extension
381-12 12' Coax Extension
381-25 25' Coax Extension
383 Dual Band Antenna
386 Wall Mount Antenna Bracket
387-2 2 dB Attack Enclosure Antenna
387-4 4' SMA to N Extension Cable
387-8 8' SMA to N Extension Cable
387-25 SMA TO N CABLE, 25FT, LMR195
387-50 SMA TO N CABLE, 50FT, LMR195
388-1 3 dB Fiberglass Antenna w/bracket
388-2 2 dB Attack Enclosure Antenna
388-3 3 dB MEG Antenna
Certifications
California State Fire Marshal (CSFM)
New York City (FDNY COA #6167)
Underwriters Laboratories (UL)
Underwriters Laboratories Canada (ULC)
For additional information, visit DMP.com
and select Compliance.
800-641-4282 | DMP.com
2500 N. Partnership Blvd, Springfield, MO 65803
Designed, engineered & manufactured in
Springfield, MO using U.S. & global components
LIMITED WARRANTY: DMP warrants that the
products manufactured by DMP and described
herein shall be free from defects of manufacture,
labeling, and packaging for a period of three
(3) years from the invoice date to the original
Buyer, provided that representative samples
of the defective products are returned to DMP
for inspection…To read the full DMP Limited
Warranty, go to DMP.com/Warranty or check the
DMP Price List or Catalog.
© 2020 Digital Monitoring Products, Inc. | LT-1027 | 20433
Loading...