DLS PS4A, PS6A, R1070, MS6, R6A User Manual

...
REFERENCE SERIES
CAR AUDIO SPEAKERS
PS4, PS5, PS6 PS4A, PS5A, PS6A R4, R5A, R6A MS5, MS6 R964, R1070
WELCOME
Thank you for buying a DLS REFERENCE speaker. This manual will show you how to do a correct installa­tion. Please read the entire manual before beginning the installation. Install the speakers yourself if you feel confident with our instructions and if you have the proper tools. However if you feel unsure, turn over the installation job to someone better suited to it.
INSTALLATION
Mount the speakers in the door or in the dashboard of your car. Normally they will fit in the facory pre-made mounting holes. If you want an improved sound reinforce with a baffle of MDF-board or similar . An installation high up on the door side is to be prefered. An alternative in­stallation is in so called kick panels down on each side of the floor with the speakers facing up- and inwards towards the listener. For two- or three way speaker systems with separate tweeter an installation of the tweeter close to the bass/ mid element is to be prefered. The tweeter can also be installed on the dash-board, or recessed in the door with the accessories in the tweeter box. It is important to fasten the speakers properly in order to avoid bad sound or rattling. For speakers with separate filters in boxes or similar it is vital that they are attached properly to the interior of the vehicle to avoid rattling. Don´t place them close to the internal wiring of the car, this can cause interference. Avoid to install filter boxes in the door sides because they can easily be broken because of rattling or moisture. Make sure the cables don´t get jammed causing a short circuit to ground. This can damage the output circuits of the head unit or amplifier. The sealing strip coming with some of the kits can be used for improved sealing between the bass element and the mounting surface. The tweeter installation for kits with separate tweeter is described on last page, or in the instruction sheet coming with the tweeters.
SPEAKER ENCLOSURES
If you want to install the speaker in an enclosure the nor­mal size for a sealed type is: 4” (10 cm) speakers : 2-4 liters 5,25” (13 cm) speakers : 6-8 liters 6,5” (16,5 cm) speakers : 10-12 liters 8” (20 cm) speakers : 15-20 liters 6 x 9” speakers : 15-20 liters 7 x 10” speakers : 20-25 liters
These volumes are only a guideline. The volumes can vary between different speakers. Contact your local DLS dealer for more exact information about your specific speaker.
TWO-WAY SYSTEMS PS4/4A, PS5/5A & PS6/6A
These 2-way systems have a separate tweeter. The filt­ers are either single filter box (PS4/5/6) or separate lowpass and highpass in a plastic boxes with selectable tweeter level inside (PS4A/5A/6A). PS-series have small installation depth and fits mots modern vehicles. Install the filter boxes in a dry place. Fasten them with screws or wire ties. If installed in the door side face the connections downwards to avoid moisture inside the filter box. On the following pages you can see how to connect the filters.
The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
TWO-WAY SYSTEMS R4, R5A & R6A
These 2-way systems have a separate tweeter. The filt­ers are combined lowpass and highpass in a plastic box with selectable tweeter level inside. R-series are spekers with heavy magnet systems giving good speker control but instead a larger installation depth. On the following pages you can see how to connect the filters.
The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
COAXIAL SPEAKERS R964 & R1070
These coaxial speakers have a separate filter box with lowpass filter for the woofer and a highpass filter for the tweeter. The tweeter level can be adjusted inside the filter box in two steps, high and low. R964 has a bi-wiring op­tion in the filter. On the following pages you can see how to connect the filter.
The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
TWO-WAY SYSTEMS MS5 & MS6
These 2-way systems have a separate 28 mm tweeter. The filters are combined lowpass and highpass in a plastic box with selectable tweeter level inside. MS-series are spekers with heavy magnet systems. The woofers mag­nesium cone body delivers a tight & controlled bass. On the following pages you can see how to connect the filters.
The filters must be used, if you connect without them the sound becomes bad and you will destroy the tweeter.
IMPORTANT! The speaker cone is made of magnesium, a material of low weight with excellent acoustic qualitys. We recommend you to NEVER touch the cone body of MS5 or MS6 with your fingers. Remaining deformation of the cone body will occour if you touch it.
SPEAKER FACTS FOR DLS REFERENCE SERIES
Model Woofer Tweeter Nom. Max Sensi- Magnet Inst. Mounting Crossover
PS4/4A 10 cm / 4” 20 mm / 0,8” 50 W 80 W 90 dB 80 mm / 3,15” 50 mm /1,97” 98 mm / 3,85” Separate boxes PS5/5A 13 cm / 5,25” 25 mm / 1” 50 W 80 W 92 dB 90 mm / 3,54” 45 mm / 1,77” 117 mm / 4,6” Separate boxes PS6/6A 16,5 cm / 6,5” 25 mm / 1” 50 W 80 W 92 dB 90 mm / 3,54” 53 mm / 2,09” 146 mm / 5,75” Separate boxes R4 10 cm / 4” 20 mm / 0,8” 50 W 80 W 94 dB 80 mm / 3,15” 60 mm / 2,36” 102 mm / 4” Separate box R5A 13 cm / 5,25” 25 mm / 1” 80 W 120 W 94 dB 90 mm / 3,54” 60 mm / 2,36” 120 mm / 4,72” Separate box R6A 16,5 cm / 6,5” 25 mm / 1” 80 W 120 W 94 dB 100 mm / 4” 76 mm / 3” 140 mm / 5,5” Separate box R964 6 x 9” 25 mm / 1” 80 W 120 W 93 dB 120 mm / 4,7” 90 mm / 3,54” 150x220 mm / 5,9x8,7” Separate box R1070 7 x 10” 25 mm / 1” 100 W 150 W 93 dB 145 mm / 5,7” 80 mm / 3,15” 156x225 mm / 6,15x8,86” Separate box MS5 13 cm / 5,25” 28 mm / 1,1” 80 W 120 W 90 dB 90 mm / 3,54” 58 mm / 2,28” 120 mm / 4,72” Separate box MS6 16,5 cm / 6,5” 28 mm / 1,1” 100 W 150 W 92 dB 100 mm / 4” 67 mm / 2,64” 140 mm / 5,5” Separate box
RUNNING-IN PERIOD
Allow the speakers to play for at least 15-20 hours. After this time the performance is correct.
SPEAKER PHASING
To be sure to have the correct speaker polarity (phase) you can check this by using a 1,5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus,
power power tivity size depth hole
CONNECTION OF SPEAKERS
Make sure you connect the cables with correct polarity to the speakers. Observe the markings on the terminal. The small terminal is minus.
+
-
and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel.
-
+
This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier.
FILTER/CROSSOVER INSTALLATIONS
Filter installation and connection of R4, R5A & R6A
-
Silver
2-way crossover
INPUT WOOFER TWEETER
+ - + - + -
Hi Low
Hi
Mid
Low
Tw
level
Silver/red Black
Black/blue
+
Head unit / amp.
-
+
Woofer
-
R4 tweeter level select:
Select tweeter level by moving the jumper inside the filter box between high or low. Make your own tests for best result.
R5A, R6A tweeter level select:
Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result.
Tweeter
+
Filter installation and connection of PS4, PS5 & PS6
Hi Mid Lo
Tw select
INPUT WOOFER TWEETER
+ - + - + -
T weeter level select:
Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result.
Silver
Silver/red Black
Black/ blue
+
Head unit/amp.
-
-
+
Tweeter
-
+
Bass/mid
Filter installation and connection of PS4A, PS5A & PS6A
Tw level
Hi Mid Lo
Silver
Silver/red
IN TWEETER
+ - + -
IN WOOFER
+ - + -
Black
Black/blue
-
+
Tweeter
-
Head unit / amp
+
-
+
Woofer
T weeter level select:
Select tweeter level by moving the jumper inside the filter box between high, mid or low. Make your own tests for best result.
Loading...
+ 2 hidden pages