D Link SL2640BT1 Users Manual

FCC Information

This equipment complies with CFR 47, Part 15.19 of the FCC rules. Operation of the equipment is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.

This device must not be co-located or operating in conjunction with any other antenna or transmitter

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Federal Communications Commission (FCC) Requirements, Part 15

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

Regulatory information / Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.

MPE Statement (Safety Information)

Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal.

Safety Information

In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.

Table of Contents

Before You Begin..........................................................................................1

Package Contents.................................................................................................1

System Requirements...........................................................................................1

Features...............................................................................................................2

HARDWARE OVERVIEW.............................................................................................3

Connections..................................................................................................3

LED Indicators..............................................................................................4

INSTALLATION............................................................................................................5

Installation Notes...................................................................................................5

Information you will need from your ADSL service provider.............................7

Information you will need about DSL-2640B...................................................8

Information you will need about your LAN or computer:..................................8

Device Installation.................................................................................................9

Power on Router...........................................................................................9

Factory Reset Button.....................................................................................9

Network Connections..................................................................................10

INTRODUCTION TO WEB CONFIGURATION.............................................................11

Preparation Before Login......................................................................................11

Logging In to the Modem.....................................................................................12

First-Time Login..........................................................................................12

Quick Setup........................................................................................................13

WAN Interface Setup...................................................................................13

LAN Interface Setup....................................................................................22

Wireless Interface Setup..............................................................................23

WAN Setup Summary.................................................................................23

Quick Setup Completion..............................................................................24

DSL Router Device Information............................................................................24

Summary of Device Information...................................................................25

WAN Interface Information...........................................................................25

Statistics of LAN..........................................................................................26

Statistics of WAN.........................................................................................26

Statistics of ATM..........................................................................................26

Statistics of ADSL........................................................................................27

Route Table Information...............................................................................28

ARP Table Information.................................................................................29

Advanced Setup..................................................................................................29

WAN Configuration......................................................................................29

LAN Configuration.......................................................................................31

NAT............................................................................................................31

Security......................................................................................................36

Parental Control..........................................................................................40

Quality of Service........................................................................................41

Routing.......................................................................................................47

DNS............................................................................................................47

DSL............................................................................................................47

Port Mapping...............................................................................................47

IPSec..........................................................................................................47

Certificate....................................................................................................47

Wireless..............................................................................................................47

Wireless LAN Basics....................................................................................47

Wireless – Basic..........................................................................................47

Wireless – Security......................................................................................47

Wireless - MAC Filter...................................................................................47

Wireless – Bridge.........................................................................................47

Wireless – Advanced...................................................................................47

Wireless -- Authenticated Stations................................................................47

Diagnostics.........................................................................................................47

Management.......................................................................................................47

Settings.......................................................................................................47

System Log.................................................................................................47

TR-069 Client..............................................................................................47

Internet Time...............................................................................................47

Access Control............................................................................................47

Update Software..........................................................................................47

Save/Reboot...............................................................................................47

TROUBLESHOOTING................................................................................................47

NETWORKING BASICS..............................................................................................47

Check Your IP Address........................................................................................47

Statically Assign An IP Address............................................................................47

TECHNICAL SPECIFICATIONS..................................................................................47

Product Overview

Before You Begin

Please read and make sure you understand all the prerequisites for proper installation of your new Router. Have all the necessary information and equipment on hand before beginning the installation.

Package Contents

= DSL-2640B ADSL Router = Power Adapter = CD-ROM with User Manual = One twisted-pair telephone cable used for ADSL connection = One straight-through Ethernet cable = One Quick Installation Guide

Warning: The Router must be used with the power adapter

included with the device.

System Requirements

• ADSL Internet service

• Computer with:

• 200 MHz Processor

• 64MB Memory

• CD-ROM Drive

• Ethernet Adapter with TCP/IP Protocol Installed

• Internet Explorer v6 or later, FireFox v1.5

• Computer with Windows 2000, Windows XP, or Windows Vista

D-Link DSL-2640B User Manual

Product Overview

Features

• PPP (Point-to-Point Protocol) Security – The DSL-2640B ADSL Router supports PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol) for PPP connections. The Router also supports MSCHAP.

• DHCP Support – Dynamic Host Configuration Protocol automatically and dynamically assigns all LAN IP settings to each host on your network. This eliminates the need to reconfigure every host whenever changes in network topology occur.

• Network Address Translation (NAT) – For small office environments, the DSL-2640B allows multiple users on the LAN to access the Internet concurrently through a single Internet account. This provides Internet access to everyone in the office for the price of a single user. NAT improves network security in effect by hiding the private network behind one global and visible IP address. NAT address mapping can also be used to link two IP domains via a LAN-to-LAN connection.

• TCP/IP (Transfer Control Protocol/Internet Protocol) – The DSL-2640B supports TCP/IP protocol, the language used for the Internet. It is compatible with access servers manufactured by major vendors.

• RIP-1/RIP-2 – The DSL-2640B supports both RIP-1 and RIP-2 exchanges with other routers. Using both versions lets the Router to communicate with all RIP enabled devices.

• Static Routing – This allows you to select a data path to a particular network destination that will remain in the routing table and never “age out”. If you wish to define a specific route that will always be used for data traffic from your LAN to a specific destination within your LAN (for example to another router or a server) or outside your network (to an ISP defined default gateway for instance).

• Default Routing – This allows you to choose a default path for incoming data packets for which the destination address is unknown. This is particularly useful when/if the Router functions as the sole connection to the Internet.

• Precise ATM Traffic Shaping – Traffic shaping is a method of controlling the flow rate of ATM data cells. This function helps to establish the Quality of Service for ATM data transfer.

• Full Network Management – The DSL-2640B incorporates SNMP (Simple Network Management Protocol) support for web-based management and text-based network management.

• Easy Installation – The DSL-2640B uses a web-based graphical user interface program for convenient management access and easy set up. Any common web browser software can be used to manage the Router.

D-Link DSL-2640B User Manual

Product Overview

Connections

Hardware Overview

D-Link DSL-2640B User Manual

Product Overview

LED Indicators

Front Panel

Side Panel

LED Color

Power

LAN 1/2/3/4 Green

WLAN Green

DSL Green

Internet

WPS (on the side panel)

Status Description

Green Red On Not bootable or device is malfunction.

Green Red On The device is attempted to become IP connected, but failed.

Blue

Off Power not supplied. On Power supplied.

Off No LAN link. Blink Data is being transmitted through the LAN interface. On LAN link is established and active. Off WLAN is disabled. Blink WLAN traffic is flowing. On WLAN link is established. Off DSL line is disconnected. Blink DSL line is training. On DSL line is connected. Off The device is under the Bridge mode, DSL connection is not present, or the power is off. Blink DSL traffic is flowing. On IP is connected.

Off Device is ready for new WPS to setup. Blink WPS is successfully triggered

Connection is successfully established between the router and the client, the LED would remain in solid light for 5s.

D-Link DSL-2640B User Manual

Installation

This section will walk you through the installation process. Placement of the Wireless ADSL Router is very important. Do not place the Router in an enclosed area such as a closet, cabinet, or in the attic or garage. Place the Wireless ADSL Router in a location where it can be easily connected to Ethernet devices, the telephone line as well as to a power source.

Installation Notes

In order to establish a connection to the Internet it will be necessary to provide information to the Router that will be stored in its memory. For some users, only their account information (Username and Password) is required. For others, various parameters that control and define the Internet connection will be required. You can print out the two pages below and use the tables to list this information. This way you have a hard copy of all the information needed to setup the Router. If it is necessary to reconfigure the device, all the necessary information can be easily accessed. Be sure to keep this information safe and private.

Low Pass Filters

Since ADSL and telephone services share the same copper wiring to carry their respective signals, a filtering mechanism may be necessary to avoid mutual interference. A low pass filter device can be installed for each telephone that shares the line with the ADSL line. These filters are easy to install passive devices that connect to the ADSL device and/or telephone using standard telephone cable. Ask your service provider for more information about the use of low pass filters with your installation.

Operating Systems

The DSL-2640B uses an HTML-based web interface for setup and management. The web configuration manager may be accessed using any operating system capable of running web browser software, including Windows 98 SE, Windows ME, Windows 2000, Windows XP, and Windows Vista.

Web Browser

Any common web browser can be used to configure the Router using the web configuration management software. The program is designed to work best with more recently released browsers such as Opera, Microsoft Internet Explorer® version 6.0, Netscape Navigator® version 6.2.3, or later versions. The web browser must have JavaScript enabled. JavaScript is enabled by default on many browsers. Make sure JavaScript has not been disabled by other software (such as virus protection or web user security packages) that may be running on your computer.

Ethernet Port (NIC Adapter)

Any computer that uses the Router must be able to connect to it through the Ethernet port on the Router. This connection is an Ethernet connection and therefore requires that your computer be equipped with an Ethernet port as well. Most notebook computers are now sold with an Ethernet port already installed. Likewise, most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment. If your computer does not have an Ethernet port, you must install an Ethernet NIC adapter before you can use the Router. If you must install an adapter, follow the installation instructions that come with the Ethernet NIC adapter.

Additional Software

It may be necessary to install software on your computer that enables the computer to access the Internet. Additional software must be installed if you are using the

D-Link DSL-2640B User Manual

Installation

device as a simple bridge. For a bridged connection, the information needed to make and maintain the Internet connection is stored on another computer or gateway device, not in the Router itself.

If your ADSL service is delivered through a PPPoE or PPPoA connection, the information needed to establish and maintain the Internet connection can be stored in the Router. In this case, it is not necessary to install software on your computer. It may however be necessary to change some settings in the device, including account information used to identify and verify the connection.

All connections to the Internet require a unique global IP address. For bridged connections, the global IP settings must reside in a TCP/IP enabled device on the LAN side of the bridge, such as a PC, a server, a gateway device such as a router or similar firewall hardware. The IP address can be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required.

Wireless LAN

Computers using the Wireless network can access the Internet or use the embedded 802.1g wireless access point. Wireless workstations must have an 802.1g or

802.1b wireless network card installed to use the Wireless ADSL Router. In addition the workstations must be configured to operate on the same channel and SSID as the Wireless ADSL Router. If wireless security is used, the wireless workstations must be properly configured for the security settings used.

D-Link DSL-2640B User Manual

Installation

Information you will need from your ADSL service provider

Username

This is the Username used to log on to your ADSL service provider’s network. Your ADSL service provider uses this to identify your account.

Password

This is the Password used, in conjunction with the Username above, to log on to your ADSL service provider’s network. This is used to verify the identity of your account.

WAN Setting / Connection Type

These settings describe the method your ADSL service provider uses to transport data between the Internet and your computer. Most users will use the default settings. You may need to specify one of the following WAN Setting and Connection Type configurations (Connection Type settings listed in parenthesis):

• PPPoE/PPPoA (PPPoE LLC, PPPoE VC-Mux, PPPoA LLC or PPPoA VC-Mux)

• Dynamic IP Address (1483 Bridged IP LLC, 1483 Bridged IP VC-Mux)

• Static IP Address (1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP LLC (IPoA) or 1483 Routed IP VC-Mux)

• Bridge Mode (1483 Bridged IP LLC or 1483 Bridged IP VC Mux)

Modulation Type

ADSL uses various standardized modulation techniques to transmit data over the allotted signal frequencies. Some users may need to change the type of modulation used for their service. The default DSL modulation (Auto Synch-Up) used for the Router automatically detects all types of ADSL, ADSL2, and ADSL2+ modulation.

Security Protocol

This is the method your ADSL service provider will use to verify your Username and Password when you log on to their network. Your Router supports the PAP and CHAP protocols.

VPI

Most users will not be required to change this setting. The Virtual Path Identifier (VPI) is used in conjunction with the Virtual Channel Identifier (VCI) to identify the data path between your ADSL service provider’s network and your computer. If you are setting up the Router for multiple virtual connections, you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections. This setting can be changed in the WAN Settings window of the web management interface.

VCI

Most users will not be required to change this setting. The Virtual Channel Identifier (VCI) used in conjunction with the VPI to identify the data path between your ADSL service provider’s network and your computer. If you are setting up the Router for multiple virtual connections, you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections. This setting can be changed in the WAN Settings window of the web management interface.

D-Link DSL-2640B User Manual

Installation

Information you will need about DSL-2640B

Username

This is the Username needed to access the Router’s management interface. When you attempt to connect to the device through a web browser you will be prompted to enter this Username. The default Username for the Router is “admin.” The user cannot change this.

Password This is the Password you will be prompted to enter when you access the Router’s management interface. The default Password is “admin.” The user may change this.

LAN IP addresses for the DSL-2640B

This is the IP address you will enter into the Address field of your web browser to access the Router’s configuration graphical user interface (GUI) using a web browser. The default IP address is 10.1.1.1. This may be changed to suit any IP address scheme the user desires. This address will be the base IP address used for DHCP service on the LAN when DHCP is enabled.

LAN Subnet Mask for the DSL-2640B

This is the subnet mask used by the DSL-2640B, and will be used throughout your LAN. The default subnet mask is 255.0.0.0. This can be changed later.

Information you will need about your LAN or computer:

Ethernet NIC

If your computer has an Ethernet NIC, you can connect the DSL-2640B to this Ethernet port using an Ethernet cable. You can also use the Ethernet ports on the DSL-2640B to connect to other computer or Ethernet devices.

DHCP Client status

Your DSL-2640B ADSL Router is configured, by default, to be a DHCP server. This means that it can assign an IP address, subnet mask, and a default gateway address to computers on your LAN. The default range of IP addresses the DSL-2640B will assign are from 10.1.1.5 to 10.1.1.254. Your computer (or computers) needs to be configured to obtain an IP address automatically (that is, they need to be configured as DHCP clients.)

It is recommended that you collect and record this information here, or in some other secure place, in case you have to re-configure your ADSL connection in the future. Once you have the above information, you are ready to setup and configure your DSL-2640B ADSL Router.

D-Link DSL-2640B User Manual

Installation

Device Installation

The Wireless ADSL Router maintains three separate interfaces, an ADSL, an Ethernet, and a Wireless LAN interface. Place the Wireless ADSL Router in a location where it can be easily connected to Ethernet devices, the telephone line as well as to a power source.

The Router can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting.

Power on Router

The Router must be used with the power adapter included with the device.

1. Connect the power adapter to the Power Input (12V DC, 1A) on the back panel of the Wireless ADSL Router and plug the other end of the power adapter to a wall outlet or power strip.

2. Push the Power Button to turn the power on.

3. The Power LED on the front panel will shine bright green to indicate the device is powered on.

4. If the Ethernet port is connected to a working device, check the LAN LED indicator to make sure the connection is valid. The Wireless ADSL Router will attempt to establish the ADSL connection, if the ADSL line is connected and the Wireless ADSL Router is properly configured the ADSL LED will light up after several seconds. If this is the first time installing the device, some settings may need to be changed before the Wireless ADSL Router can establish a connection.

Factory Reset Button

The Router may be reset to the original factory default settings by using a ballpoint or paperclip to gently push down the reset button in the following sequence:

1. With the router powered on (check the Power LED to make sure it lights steady green), press and hold down the reset button using a paper clip or similar object for about 6 to 8 seconds.

2. The router will restart. Watch the Power LED to verify that it is restarting.

3. When it is powered on again it is ready to be configured. The whole process takes about 30 seconds.

4. The device settings will be restored to the factory default IP address 10.1.1.1 and the subnet mask is 255.0.0.0, the default management Username is “admin” and the default Password is “admin.”

Note: A factory reset will erase the current configuration settings and reset them to the default settings. After it has restarted, log in to the router’s web-based

management interface and use the Setup Wizard to configure the basic settings.

D-Link DSL-2640B User Manual

Installation

Network Connections

Connect ADSL Line

Use the ADSL cable included with the Router to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Router and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions included with the device or given to you by your service provider. The ADSL connection represents the WAN interface, the connection to the Internet. It is the physical link to the service provider’s network backbone and ultimately to the Internet.

Connect Router to Ethernet

The Router may be connected to a single computer or Ethernet device through the 10/100BASE-TX Ethernet port on the rear panel. Any connection to an Ethernet concentrating device such as a switch or hub must operate at a speed of 10/100 Mbps only. When connecting the Router to any Ethernet device that is capable of operating at speeds higher than 10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting port. Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 port on the Router is a crossed port (MDI-X). Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. When connecting the Router directly to a PC or server use a normal straight-through cable. You should use a crossed cable when connecting the Router to a normal (MDI-X) port on a switch or hub. Use a normal straight-through cable when connecting it to an uplink (MDI-II) port on a hub or switch. The rules governing Ethernet cable lengths apply to the LAN to Router connection. Be sure that the cable connecting the LAN to the Router does not exceed 100 meters.

Hub or Switch to Router Connection

Connect the Router to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable. If you wish to reserve the uplink port on the switch or hub for another device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable.

Computer to Router Connection

You can connect the Router directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided.

Wireless Connection to Router

The Router’s embedded 802.11g wireless access point should be configured to suit the local wireless network. All 802.11g or 802.11b devices that associate with the Router’s wireless access point must have the same SSID and channel. If wireless security is used, the wireless clients must be configured with the correct security information to use the Router. More information on configuring the wireless settings is found later in this manual.

D-Link DSL-2640B User Manual

Web Configuration

Introduction to Web Configuration

The first time you setup the Router. It is recommended that you configure the WAN connection using a single computer, to ensure that both the computer and the Router are not connected to the LAN. Once the WAN connection operates properly, you may continue to make changes to Router configuration, including IP settings and DHCP setup. This chapter is concerned with using your computer to configure the WAN connection. The following chapter describes the various menus used to configure and monitor the Router, including how to change IP settings and DHCP server setup.

Preparation Before Login

Before accessing the Modem, ensure the communication between PC and Modem is normal. Check the communication as follows.

= Configure the IP address of the PC as 10.1.1.X (2~254), net mask as

255.0.0.0, gateway address as 10.1.1.1 (for customized version, configure them according to the actual version).

= Enter arp -a in the DOS window to check whether the PC can read the MAC

address of the Modem.

= Ping the management IP address (10.1.1.1 by default) of the Modem.

If the PC can read the MAC address of the Modem and can ping through the management IP address of the Modem, that means the communication of the PC and the Modem is normal.

Note: When you manage the Modem through Web, you must keep the Modem power on. Otherwise, the Modem may be damaged.

Web Configuration

Logging In to the Modem

The following description is a detail “How-To” user guide and is prepared for first time users.

First-Time Login

When you log in to the DSL Router for the first time, the login wizard appears.

Step 1 Open a Web browser on your computer. Step 2 Enter http://10.1.1.1 (DSL router default IP address) in the address bar. The login page

appears.

Step 3 Enter a user name and the password. The default username and password of the super

user are admin and admin. The username and password of the common user are user and

user. You need not enter the username and password again if you select the option Remember my password. It is recommended to change these default values after logging

in to the DSL router for the first time.

Step 4 Click OK to log in or click Cancel to exit the login page.

After logging in to the DSL router as a super user, you can query, configure, and modify all configurations, and diagnose the system. You need to reboot the DSL router to enable your modification or configuration effective in some cases, for example, after you modify the PVC configuration. Some

modification, such as adding a static route, takes effect at once, and does not require modem reboot.

Web Configuration

Quick Setup

The Quick Setup page mainly includes the following three functions:

= WAN interface setup = LAN interface setup = Wireless interface setup

Quick setup enables fast and accurate configuration of your Internet connection and other important parameters. The following sections describe these various configuration parameters. Whether you configure these parameters or use the default ones, click Next to enable your Internet connection.

When subscribing to a broadband service, you should be aware of the method by which you are connected to the Internet. Your physical WAN device can be Ethernet, DSL, or both. Technical information regarding the properties of your Internet connection should be provided by your Internet service provider (ISP). For example, your ISP should inform you whether you are connected to the Internet by using a static or dynamic IP address, or the protocols, such as PPPOA or PPPoE, which you use to communicate over the Internet.

WAN Interface Setup

During WAN interface setup, you can set up a PVC and its properties:

= VPI = VCI = QoS = Internet connection type = Encapsulation type = IGMP service = NAT

Setting Up VPI/VCI and QoS

After logging in to the DSL router, if no PVC is configured previously and no default settings exist, the Quick Setup webpage appears, which contains some basic configuration that is needed by ATM PVC. The following introduction guides you through the necessary steps to configure your DSL Router.

Web Configuration

According to your ISP instructions, specify the following parameters: = VPI (Virtual Path Identifier)

Virtual path between two points in an ATM network. The valid value range is from 0 to 255.

= VCI (Virtual Channel Identifier)

Virtual channel between two points in an ATM network. The valid value range is from 32 to 65535 (1 to 31 are reserved for known protocols).

= Enable Quality Of Service

Enabling QoS for a PVC improves performance for selected classes of applications. However, since QoS also consumes system resources, the number of PVCs is reduced consequently. Use Advanced Setup/Quality of Service to assign priorities for the applications.

For example, PVC 0/35 is to be modified and the default values of QoS remain. In actual applications, you can modify them depending on your ISP instructions.

Selecting Internet Connection Type and Encapsulation Type

You can select your connection type from the following list. Each connect type corresponds to several encapsulation types:

= PPP over ATM (PPPoA)

PPPoA Encapsulation Mode: VC/MUX, LLC/ENCAPSULATION

= PPP over Ethernet (PPPoE)

PPPoE Encapsulation Mode: LLC/SNAP-BRIDGING, VC/MUX

= MAC Encapsulation Routing (MER)

MER Encapsulation Mode: LLC/SNAP-BRIDGING, VC/MUX

= IP over ATM (IPoA)

IPoA Encapsulation Mode: LLC/SNAP-ROUTING, VC/MUX

= Bridging

Bridging Encapsulation Mode: LLC/SNAP-BRIDGING, VC/MUX

For example, change the connection type of PVC 0/35 to Bridging. Select Bridging, and set Encapsulation Mode to LLC/SNAP-BRIDGING (depending on the uplink equipment).

D-Link DSL-2640B User Manual

Web Configuration

Internet Connection Type - PPP over ATM (PPPoA)

Step 5 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 6 In the Internet connection type and encapsulation type page, set the Connection

Type to PPP over ATM (PPPoA) and select the encapsulation mode.

D-Link DSL-2640B User Manual

Web Configuration

Step 7 Click Next and the PPP information configuration page appears.

Your ISP should provide you with the following information:

= PPP Username = PPP Password = Authentication Method

You can also select another service function as follows:

= Dial on demand (with idle timeout timer) = PPP IP extension = Use static IP address = Retry PPP password on authentication error = Enable PPP debug mode

Step 8 Click Next and the PPPoA IGMP and WAN function configuration page appears.

To use IGMP service on pppoa pvc, select the Enable IGMP Multicast check box.

D-Link DSL-2640B User Manual

Web Configuration

Internet Connection Type - PPP over Ethernet (PPPoE)

Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection Type to

PPP over Ethernet (PPPoE) and select the encapsulation mode.

Web Configuration

Step 3 Click Next and the PPP information configuration page appears.

Your ISP should provide you with the following information:

= PPP Username = PPP Password = Authentication Method

You can also select another service function as follows:

= Dial on demand (with idle timeout timer) = PPP IP extension = Use Static IP Address = Retry PPP password on authentication error = Enable PPP Debug Mode

Step 4 Click Next and the PPPoE IGMP and WAN function configuration page appears.

To use IGMP service on pppoe pvc, select the Enable IGMP Multicast check box.

D-Link DSL-2640B User Manual

Web Configuration

Internet Connection Type - MAC Encapsulation Routing (MER)

Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection

Type to MAC Encapsulation Routing (MER) and select the encapsulation mode.

Step 3 Click Next and the WAN IP configuration page appears.

You can select the service function as follows:

= Obtain an IP address automatically (use dhcp to obtain wan ip) = Use the following IP address (use static wan ip) = Obtain default gateway automatically (use dhcp to obtain gateway IP) = Use the following default gateway (use static gateway ip) = Obtain DNS server addresses automatically (use dhcp to obtain DNS server IP) = Use the following DNS server addresses (use static DNS server IP)

Web Configuration

Step 4 Click Next and the MER IGMP and WAN function configuration page appears.

To use IGMP service on MER pvc, select the Enable IGMP Multicast check box. In the MER mode, you can configure the following functions:

= Enable NAT. = Enable Fullcone NAT. = Enable Firewall.

Internet Connection Type - IP over ATM (IPoA)

Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection

Type to IP over ATM (IPoA) and select the encapsulation mode.

D-Link DSL-2640B User Manual

Web Configuration

Step 3 Click Next and the WAN IP configuration page appears.

You can select the service function as follows:

= Use the following IP address (static wan ip) = Use the following default gateway (static gateway ip) = Use the following DNS server addresses (static DNS server ip)

Step 4 Click Next and the IPoA IGMP and WAN function configuration page appears.

To use IGMP service on ipoa pvc, select the Enable IGMP Multicast check box. In the MER mode, you can configure the following functions:

= Enable NAT. = Enable Fullcone NAT. = Enable Firewall.

Internet Connection Type – Bridging

Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS.

D-Link DSL-2640B User Manual

Web Configuration

Step 2 In the Internet connection type and encapsulation type page, set the Connection

Type to Bridging and select the encapsulation mode.

Step 3 Click Next and the Bridging service configuration page appears.

LAN Interface Setup

The LAN interface setup page is shown on the right.

D-Link DSL-2640B User Manual

Web Configuration

Wireless Interface Setup

Enable Wireless: Select or deselect the check box to enable or disable wireless connection. SSID: It is the network name shared among all points in a wireless network. The SSID must be

identical for all points in the wireless network. It is case-sensitive and must not exceed 32 characters (use any character on the keyboard).

WAN Setup Summary

In WAN setup summary, you can view the following properties of the added PVC:

= VPI/VCI = Connection Type: = Service Name: = Service Category: = IP Address: = Service State: = NAT = Firewall = IGMP = QoS

D-Link DSL-2640B User Manual

Web Configuration

To make any modifications, click Back. Click Save/Reboot, and the following page appears.

Note: You need to reboot to activate this WAN page and further configure services in this

interface, and it takes about two minutes to reboot.

Quick Setup Completion

After the previous setup, you can immediately start using your gateway to:

= Share a broadband connection among multiple users (HTTP, FTP, Telnet, NetMeeting) and between all of the computers connected to your home network. = Build a home network by connecting additional PCs and network devices to the gateway. = Control network parameters, including DHCP, DNS, and WAN settings. = View network status, traffic statistics, system log, and more. = Allow access from the Internet to games and other services provided by computers in the home network. = Prohibit computers in the home network from accessing selected services on the Internet. = Block access to specific Internet websites from your home network.

If your gateway is equipped with multiple LAN ports, you can connect additional devices directly to the gateway. Otherwise, connect a hub or switch to the LAN port, to which you can connect additional devices. In both cases, configure newly connected devices to automatically obtain IP address as previously described.

DSL Router Device Information

Click Device Info and you can view the following information.

= Summary = WAN = Statistics = Route = ARP = DHCP

D-Link DSL-2640B User Manual

+ 61 hidden pages