Page 1
OSMO
External Battery Extender
Quick Start Guide
2016.04
V1.0
Page 2
Disclaimer and Warning
Congratulations on purchasing your new DJI product. The
information in this document affects your safety and your legal
rights and responsibilities. Read this entire document carefully to
ensure proper conguration before use. Failure to read and follow
instructions and warnings in this document may result in serious
injury to yourself or others, damage to your DJI product, or damage
to other objects in the vicinity. This document and all other collateral
documents are subject to change at the sole discretion of DJI. For
up-to-date product information, visit http://www.dji.com and click on
the product page for this product.
By using this product, you hereby signify that you have read this
disclaimer and warning carefully and that you understand and
agree to abide by the terms and conditions herein. You agree that
you are solely responsible for your own conduct while using this
product, and for any consequences thereof. You agree to use
this product only for purposes that are proper and in accordance
with all applicable laws, rules, and regulations, and all terms,
precautions, practices, policies and guidelines DJI has made and
may make available.
DJI accepts no liability for damage, injury or any legal responsibility
incurred directly or indirectly from the use of this product. The user
shall observe safe and lawful practices including, but not limited to,
those set forth in this document.
Introduction
The Osmo external battery extender is designed to prolong the
operating time of the Osmo by connecting to external power
sources such as a dedicated DJI charger or Intelligent Battery. It
is ideal for using the Osmo in extended period operations such
as timelapse.
1
Page 3
Usage
1. Remove the original Osmo battery cover.
Use a pin or sharp object to slide the spring needle on the hinge
of the battery cover to the left. Then remove the original battery
cover from the Osmo.
Spring Needle
2. Install the new Osmo battery cover.
Insert one end of the spring needle on the battery cover into
the left mounting hole on the Osmo handle.
Slide the spring needle on the hinge to the left to insert it into
the right mounting hole.
Note that the spring must be fitted into the dedicated
mounting hole on the Osmo handle.
Spring
Mounting
Hole
2
Page 4
3. Insert the External Battery Extender into the Osmo handle as
shown below. Pull the External Battery Extender cable through
the battery cover.
4. Connect the External Battery Extender to an external power
supply such as the dedicated DJI Charger or Battery (refer to
the Specications to learn more).
If using a DJI Intelligent Battery as the power supply, a
Battery (10 PIN-A or 2 PIN) to DC Power Cable is required
and can be purchased separately from the ofcial DJI Online
Store.
3
Page 5
The Osmo Base is compatible with the External Battery Extender.
Specications
Supported DJI Charger Models
PH4C100 (Phantom 4 - 100W Charger)
ADE019 (Phantom 3 - 100W Charger)
A14-057N1A (Phantom 3 - 57W Charger)
ADE018 (Inspire 1 - 180W Charger)
A14-100P1A (Inspire 1 - 100W Charger)
Supported DJI Car Charger Models
C4S90-4 (Phantom 4 Car Charger)
C4S90 (Phantom 3 Car Charger)
C6S90 (Inspire 1 Car Charger)
4
Page 6
Supported DJI Intelligent Battery Models
*
PH4-5350mAh-15.2V (Phantom 4 Intelligent Flight Battery
PH3-4480mAh-15.2V (Phantom 3 Intelligent Flight Battery
TB47/TB48 (Inspire 1 Intelligent Flight Battery
**
844297-4350mAh-15.2V (Ronin Intelligent Battery
824380-3400mAh-14.8V (Ronin Intelligent Battery
423496-1580mAh-14.4V (Ronin-M Intelligent Battery
* Must be used with Battery (10 PIN-A) to DC Power Cable
** Must be used with Battery (2 PIN) to DC Power Cable
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
EU Compliance Statement
SZ DJI TECHNOLOGY CO., LTD hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of the EMC Directive.
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany
DJI Support:
www.dji.com/support
The content in this document is subject to change.
Download the latest version from
www.dji.com/product/osmo
If you have any questions about this document, please contact DJI
by sending a message to DocSupport@dji.com.
2016 DJI. All Rights Reserved.
©
)
**
)
)
**
)
**
)
**
)
Loading...