Dixon ZTR 5004, ZTR 5023 User Manual
ZTR®
5000 SERIES
OPERATORS MANUAL
2003
IMPORTANT - READ CAREFULLY
The Dixon® ZTR® Mower is both easy and fun to operate.
However, any power mower must be operated properly to be
safe. It is not a toy or a recreational vehicle. Before you
start to use the mower, read the operators manual carefully
and become completely familiar with the controls.
The information contained in this manual applies to all
Dixon® ZTR® 5000 Series Mowers. Your Dixon dealer
will gladly answer any questions.
See your dealer for warranty service, parts and repairs.
INDEX
Page
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14
Seat Adjustment Instructions. . . . . . . . . . . . . . . . . . . . . . . . .15
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-20
Operation Instructions. . . . . . . . . . . . . . . . . . . 21-32
Care & Maintenance. . . . . . . . . . . . . . . . . . . . . .33-54
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 55-56
Standard Service Parts List. . . . . . . . . . . . . . . . . . . .57-58
5000 Series
Part No. 13634-0702
3
SAFETY
RIDING LAWN MOWERS,
IF IMPROPERLY OPERATED,
CAN CAUSE SERIOUS INJURY OR DEATH.
The most common causes of injury to the operator or bystander...
BLADE CONTACT
TIP OVER
RUN OVER
BACK OVER
...read and understand this manual to prevent injuries.
4
SAFETY
Safety Alert Symbol
When you see this symbol,
BE ALERT to the potential for injury.
Follow recommended safety precautions
and safe operating practices.
DANGER
(highlighted in red)
indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING
(highlighted in orange)
indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION
(highlighted in yellow)
indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury. It may also be used
to alert against unsafe practices.
5
Failure to observe the following safety
instructions could result in serious injury or death.
GENERAL OPERATION:
Read, understand, and follow all instructions in the manual
and on the mower before starting.
Only allow responsible adults, who are familiar with the
instructions, to operate the mower.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing.
Stop mower if anyone enters the area.
NEVER carry passengers.
SAFETY
Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
Be aware of the mower discharge direction and do not point
it at anyone.
Do not operate the mower without either the entire grass
catcher or the deflector in place.
Slow down before turning.
Never leave a running mower unattended. Always turn off
blades, set parking brake, stop engine and remove key before
dismounting.
6
SAFETY
GENERAL OPERATION (continued):
Turn off blades when not mowing.
Stop engine before removing grass catcher or unclogging
chute.
Mow only in daylight or good artificial light.
Do not operate the mower while under the influence of
alcohol or drugs.
Watch for traffic when operating near or crossingroadways.
Use extra care when loading or unloading the mower into a
trailer or truck. Do not ride the mower when loading and
unloading.
Always wear safety goggles or safety glasses with side
shields when operating mower.
Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability to
operate the riding mower safely enough to protect
themselves and others from serious injury.
Follow the manufacturers recommendation for wheel
weights and counterweights.
•Maintain or replace safety & instruction labels as needed.
WARNING:
The engine exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive
harm.
7
SLOPE OPERATION:
SAFETY
Slopes are a major factor related to loss-of-control and tip-over accidents,
If you cannot back up the slope or if you feel uneasy on it,
DO
which can result in severe injury or death.
All slopes require extra caution.
do not mow it!
Mow across the slope with your Dixon ZTR - never up or down.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain could overturn the
mower. Tall grass can hide obstacles.
Use slow speed. Tires may lose traction on slopes even though the
brakes are functioning properly.
Use extra care with grass catchers or other attachments. These can
change the stability of the mower.
Keep all movement on the slopes slow and gradual. Do not make
sudden changes in speed or direction.
Avoid starting or stopping on a slope. If tires lose traction, disengage
the blades and proceed slowly down the slope.
If front wheels lift off the ground, pull the levers back to stabilize the
mower.
DO NOT
Do not turn on slopes unless necessary, and then, turn slowly and
gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The mower
could suddenly turn over if a wheel is over the edge of a cliff or ditch,
or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause sliding.
Do not try to stabilize the mower by putting your foot on the ground.
Do not use grass catcher on steep slopes.
8
SAFETY
CHILDREN:
Tragic accidents can occur if the operator is
not alert to the presence of children.
Children are attracted to lawn mowers and the mowing activity.
NEVER assume children will stay where they were last seen.
Be alert to avoid accidents.
Keep children out of the mowing area and under the
watchful care of another responsible adult.
Be alert and turn mower off if a child enters the area.
Before and during backing, look BEHIND and DOWN for
small children.
Never carry children. They may fall off and be seriously
injured or interfere with safe mower operation.
Never allow children to operate the mower.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
9
SAFETY
SERVICE:
Use extra care in handling gasoline and other fuels. They are
flammable and vapors are explosive.
Use only an approved container.
Never remove fuel cap or add fuel with engine running.
Allow engine to cool before refueling.
Do not smoke while refueling.
Never refuel the mower indoors.
Never store the mower or fuel container inside a building
where there is an open flame.
If fuel is spilled on clothing, change clothing immediately.
To prevent fire and explosion caused by static electricity:
Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
10
When practical, remove fuel-powered equipment
from the truck or trailer and refuel it on the
ground. If this is not possible, then refuel such
equipment on a trailer with a portable container,
rather than from a fuel dispenser nozzle.
If a fuel dispenser nozzle must be used, keep the
nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
SAFETY
SERVICE (continued):
Never run a mower inside a closed area. The exhaust fumes are
toxic.
Keep nuts and bolts tight, especially blade attachment bolts, and
keep equipment in good condition.
Never tamper with safety devices. Check their proper operation
regularly.
Keep mower free of grass, leaves, or other debris buildup. Clean
up oil or fuel spillage. Allow mower to cool before storing.
Stop and inspect the equipment if you strike an object. Repair,
if necessary, before restarting.
Never make adjustments or repairs with the engine running
unless otherwise specified.
Grass catcher components are subject to wear, damage and
deterioration, which could expose moving parts or allow objects
to be thrown. Frequently check components and replace with
original equipment parts, when necessary.
Mower blades are sharp and can cut. Wrap the blade(s) or wear
gloves, and use extra caution when servicing them.
Batteries contain sulfuric acid. To prevent burns avoid contact
with skin, eyes and clothing. To prevent a fire or explosion keep
sparks and open flames away from battery.
Before disconnecting the negative (-) ground cable, make sure all
switches are OFF.
11
DIXON LIMITED WARRANTY POLICY - HYDRO GEAR MODELS
5000 - 6000 - 7000 Series Mowers
WARRANTY: Dixon Commercial Warranty is for a period of one (1) year from date of purchase
or 400 hours of use, whichever occurs first. Mowers used for Homeowner Application (used only
at owners primary place of residence) are warranted for two (2) years from date of purchase.
DIXON ZTR MOWERS ARE WARRANTED AGAINST DEFECTS IN MATERIALS AND
WORKMANSHIP AND PROVIDES FOR REPLACEMENT OR REPAIR OF PARTS INCLUDING LABOR
COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS:
1. Warranty applies only to original retail purchaser of new and unused mowers and
2. All Dixon warranty must be accomplished by authorized Dixon dealers and in
3. Battery warranty: Limited to 90 days from date of purchase.
4. Accessories Warranty (Grass Catchers, Snow Blades, Covers, etc.): Limited to 90
5. Warranty does not apply to damage in transit or incidents of misuse, negligence,
6. The following items are not covered by this warranty policy:
7. There is no other express warranty. Implied warranties, including those of merchant
WARRANTY VALIDATION: At the time of sale, selling dealer must review each portion of this
warranty document, complete the information section below, secure customer's signature and
send copy to Dixon Industries, Inc.
Date of Purchase Model Deck Size S/N
accessories.
accordance with Dixon warranty policy and allowances. All warranty claims must be
approved by Dixon Industries, Inc.
days from date of purchase.
accidents, or alteration. The use of parts or components other than those supplied
by Dixon Industries, Inc. VOIDS ALL WARRANTY.
(a) Pick up and delivery charges for transportation of mower to and from an
Authorized Dixon Dealer's place of business.
(b) Routine maintenance or adjustments
(c) Belts/Blades/Hydro filters
(d) Engines -- All engines used on Dixon ZTR mowers are warranted by each
individual engine manufacturer.
(e) Any costs or expense of providing substitute equipment while repair work is
being performed on a warranted mower.
ability and fitness for a particular purpose, are limited to the same duration of the
express warranty, and to the extent permitted by law any and all implied warranties
are excluded. Liabilities for consequential damages under any and all warranties are
excluded.
Copies: Pink/Customer Yellow/Dealer White/Return to Dixon Ind.
(Owner's Name)
(Street Address)
(City/State/Zip)
DIXON INDUSTRIES, INC.
A BLOUNT International Inc. Co.
PO BOX 1569
COFFEYVILLE KS 67337 0945
PHONE 620 251 2000
FAX 620 251 4117
12
(Dealership Name & Dealer Number)
(Street Address)
(City/State/Zip)
(Dealer's Signature)(Owner's Signature)
www.dixon-ztr.com
1-877-CUT-MORE
SPECIFICATIONS
Model ZTR 5004/5005
CHASSIS: 11 GA - rectangular tube
BODY: Two piece-made of rotational molded polyethylene. Front
SEAT: Designed for operator comfort by use of high-density
MOWER DECK: Two decks are available. The 42 is made of stamped
BLADE DRIVE: Electric clutch
DRIVE SYSTEM: Each rear wheel is independently driven by a HydroGear
ENGINE: 19HP Kawasaki overhead valves, replaceable oil filter, full
STARTING SYSTEM: Electric by key switch operation with safety interlocks on
TIRES: Front 11 X 4 X 5 ribbed tread
body contains access panels for battery service & engine
to mower deck belt removal. Rear body tilts up to allow
service on the entire drive system.
closed cell foam padded back rest and arm rests,
upholstered with Cordura
is adjustable fore and aft.
steel. The 50 is made of 11 GA fabricated welded
construction with external reinforcement ribs. Three
blades combine for either a 42 or 50 cut width. Cut
height approximately 1.5 to 4.5 via 7 position lift handle.
BDU-10L Series 70 hydrostatic transmission. The hydrostatic
transmissions power a fully enclosed HydroGear gearbox.
pressure lube system, dual element air cleaner, integral fuel
pump.
parking brake and blade drive clutch.
Rear 20 X 10 X 8 Multi-Trac
TM
water-repellent fabric. Seat
RECOMMENDED Front 16 - 21 lbs.
TIRE PRESSURE: Rear 8 - 14 lbs.
CAPACITIES: Fuel - 4.8 gallons total (dual tanks)
Oil tank - 3 quart with in-line 40 micron filter
Engine - 2 qts. SAE 30 (with filter)
DIMENSIONS: Width 55 (42 Deck), 60 (50 Deck)
Height 45
Length 72:
Weight 594 lbs, (42 Deck], 650 lbs (50 Deck)
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
13
SPECIFICATIONS
Model ZTR 5023
CHASSIS: 11 GA - rectangular tube
BODY: Two piece - made of high-density polyethylene. Front body contains
SEAT: Designed for operator comfort by use of high density closed cell
MOWER DECK: Two decks are available. The 60" is made of stamped steel. The
BLADE DRIVE: Electric clutch
DRIVE SYSTEM: Each rear wheel is independently driven by a HydroGear BDU-10L
ENGINE: 23HP Kohler Command, 4-Cycle, V-Configuration, Overhead Valve,
STARTING SYSTEM: Electric by key switch operation with safety interlocks on parking
TIRES: Front 11 X 4 X 5 Ribbed Tread
access panels for battery service and engine to mower deck belt
removal. Rear body tilts up to allow service on the entire drive
system.
foam padded back and arm rests, upholstered with Cordura
water-repellent fabric. Seat is adjustable fore and aft.
50" is made of 11 GA fabricated welded construction with external
reinforcement ribs. Three blades combine for a 50" or 60" cut
width. Cut height approximately 1.5" to 4.5" via 7 position lift
handle.
Series 70 hydrostatic transmission.The hydrostatic
transmissions, in turn, power a fully enclosed HydroGear gearbox.
Air-Cooled, Gasoline, Vertical Shaft, Aluminum Head, and Crankcase
with Cast Iron Liners, Full Pressure Lubrication/Full Flow Filter,
Pulse-type Fuel Pump, Fixed Jet Carburetor w/Smart-Choke,
Electronic Ignition, In-Line Fuel Filter, Dual Element Air Cleaner.
brake and blade drive clutch.
Rear 20 X 10 X 8 Multi Trac
TM
RECOMMENDED Front 16 - 21 lbs.
TIRE PRESSURE: Rear 8 - 14 lbs.
CAPACITIES: Fuel - 4.8 gallons total (dual tanks)
DIMENSIONS: Width 60"(50" Deck), 72"(60" Deck)
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION
Hydrostat oil tank - 3 quart with in-line 40 micron filter
Engine - 2 qts. SAE 10W30 (with filter)
Height 45"
Length 72"
Weight 680 lbs.(50" Deck), 685 lbs.(60" Deck)
14
SEAT ADJUSTMENT INSTRUCTIONS
5000 Series Models
1. Grasp seat slide adjuster and move
it into adjustment position.
2. Slide seat forward or backward.
3. Release seat slide adjuster.
15
CONTROLS
CONTROL LEVERS
Note: For access to the seat, move control levers to neutral position and
swing them outward.
TO GO FORWARD:
•From neutral position, gently push both control levers forward.
•To increase speed, move levers further forward.
TO GO BACKWARD:
•From neutral position, gently pull both control levers toward you.
TURNING:
•Turning is controlled by moving one control lever slightly forward or
rearward of the other.
•To turn left, move left lever rearward of the right lever.
•To turn right, move right lever rearward of the left lever.
•To turn on mowers own axis (zero turning radius), stop and move one
lever to reverse position and the other to forward position.
BRAKING:
•To brake mower, move both levers in direction opposite of travel.
LEFT TURN OPPOSITE
Note: The pressure required to operate the mower is very light.
16
CONTROLS
CHOKE CONTROL LEVER:
•Located on control panel to operators right.
•Used to start a cold engine.
THROTTLE CONTROL LEVER:
•Located on control panel to operators right.
•Controls engine speed, slow to maximum.
•While moving, throttle control should be set to
MAXIMUM for wide open setting to insure
adequate cooling of the engine and to maintain
mower deck blade speed.
17
CONTROLS
PARKING BRAKE:
The parking brake is designed to hold the mower from moving and is
not intended for use in stopping the mower while it is in motion.
CAUTION Engage parking brake before
starting engine.
TO SET PARKING BRAKE:
The hand operated brake is located at
the left hand side of the mower.
To engage brake, pull lever up (to the
rear).
To release brake, move lever forward
(down).
Note: Always set parking brake
before dismounting. Release
parking brake before moving
mower.
HYDRO GEAR SYSTEM:
•Allows the mower to turn on its own
axis (zero turning radius).
•Each lever controls one side of the
mower.
•Note: The pressure required to operate
the mower is very light.
18
Loading...