Page 1
TECHNICAL DATA BROCHURE
ZTR 308
-
311
DIXON INDUSTRIES, INC. B
OX 484, COFFEYVILLE, KANSAS 67337 (316) 251
-
2000
IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION.
Seat Adjustment
Loosen Bolts on sliding brackets under each side of seat, slide seat forward or rearward to
desired position. Re -tighten bolts. Do not operate mower with bracket bolts in a loose
condition.
Mower Blade Operation
To start mower blades, move lever on floor slowly to "ENGAGE" position. To stop
mower blades, move lever on floo r slowly to "DISENGAGE" position.
Body Removal
1. Disconnect throttle cable from engine.
2. Disconnect the rear wiring loom (P/N 4109) from the body by lightly squeezing
Seal plug. This is located at the left rear of the body.
3. Note: Loosen bolts that hold body switch (P/N 4079) and slide switch away
the Econo-
from engaging
rod. Tighten one bolt just enough to hold switch in this position until body is
reassembled.
4. Remove 4 control lever bolts and remove upper control levers (P/N 1501L-1501R).
5. Remove engaging handle (P/N 6089) by removing bolt and nut under handle.
6. Remove the 2 attach nuts on floor of body and 2 sheet metal screws at the
rear of body.
7. Place height adjustment lever in vertical position, engage parking brake and carefully lift
body up and off chassis.
8. Reverse the above procedure for assembly.
Safety Checks
With the mower deck in the engaged position slide the body switch (P/N 4079) toward
the engaging rod (P/N 6087-1) until the switch leaf just makes contact with the
switch button. Tighten both bolts in switch bracket.
With mower deck engaged, attempt to start engine in all cutting height positions.
If engine starts in any cutting height position, re-adjust the switch. Disengage
the mower deck and start the engine in each cutting height position. If engine
fails to start in any cutting height position, re-adjust switch.
With operator in normal mowing/position, engage mower deck and remove weight from
seat. The engine should stop. Repeat this procedure in each cutting height
position. If engine does not stop when operator rises from seat in each cutting
height position, return to an authorized Dixon dealer for adjustment f>r repairs.
Parking Brake Adjustment
Remove body as described above. Tighten nut on brake rod (P/N2533) (Located in
transaxle on each side.), just enough to prevent brake from slipping
Over tightening may cause premature wear on brake band (P/N 5085).
Mower Drive Belt Adjustment
when engaged. CAUTION:
Belt tension for mower drive belt (P/N 2412) is adjusted by loosening nut on the
arm assembly (P/N 2171 -A) and turning bolt to achieve desired tension.
Tension should be checked with belt in engaged position.
Removing Mower Deck
Re-tighten nut.
1. Remove engaging handle (P/N 6089) by removing bolt and nut under handle.
front of the
connecting
2. Loosen belt keeper (P/N 2234) located under engine by loosening 2 rear engine
mount bolts to allow mower deck drive belt to come free of rear pulley.
Re-tighten belt keeper,
(continued on back) 1
D.I. Form S -35 (Rev. 6/83)
Page 2
3
Page 3
4
Page 4
ART # NAME
PART # NAME
PART # NAME
1015 Caster Weldment
1020 Caster Axle
1022 Caster Wheel & T1re
1022A Caster Wheel Bearing
I030 Upper Lift Link-Rear
I039 Lower Lift Link
1108 Tire - Front Wheel
1109 Inner Tube - Front Wheel
1501R Upper Control Lever
ISOIL Upper Control Lever
1507 Wheel/Deck Hub Bearing
1536 Chain Connecting Link
1540 Engine Shaft Key
543 Lift Knob
544 Bellcrank
560-1 Battery Splash Guard
574 Brake Pivot Weldment
606 Brake Mount Weldment
647 Control Pin
654 Transaxle Idler Weld.
655 Transaxle Idler Pulley
657 Transaxle Idler Spring
2000-2 Frame Weldment
2077 Walking Beam Weldment
2100 Bumper Weldment
2105 Bumper Pad
2154 Hub Pulley Spacer
2155 Hub Bearing Spacer
2159 Engaging Idler Spacer
2164 Support Sprocket Spacer
2165-1 Torque Rod
2166 Pivot Bolt
2171A Connecting Arm Assy.
2171-1 Connecting Arm Weldment
2172 Swivel Fitting
2176 Body
2179 Switch Bracket-Body
2180 Switch Bracket-Sw. Sect.
2204 Wheel Hub
2214R Brake Arm Weldment R
2214L Brake Arm Weldment L
2221 Transaxle Shim 16ga
2222 Transaxle Shim 22ga
2225 Battery Box Weldment
2231 Lower Control Lever Assy
2234 Belt Keeper
2237 Tie Bar Assy.
2238 Tie Bar
2240 Short Brake Rod Assy.
2402 Rear Wheel & Tire
406 30" Mower Blade
408 Drive Chain Assy.
411 Mower Deck V-Pulley
412 Deck Drive Belt
413 V-Idler Pulley
414 Engaging Idler Tension Sprg
417 Control Rod Assy
418 Long Brake Rod Assy
422 Name Decal
436 Switch Decal
2444 Battery Ground Cable
2449 Caster Nipple
2452 Engaging Idler Bshg.
2456 Model Decal-ZTR 308
2460 Parking Brake Decal
2463 Seat
2465 Rear Tire(16x6.5-8)
2466 Rear Rim (16x6.5-8)
2468 Double Engine Pulley
2469 V-Belt
2470 Transaxle Pulley
2501 Rear Tube' Weldment
2504 Front Tube
2507 Support L
2508 Support R
2509 Support Shaft
2514 Torque Rod Stiffener R
2515 Torque Rod Stiffener L
2524 Transaxle
2600-3 Mower Deck Assy.
2601-2 Mower Deck Weldment
2612 Engaging Idler Weld.
2620-1 Engaging Rod
2626 Deflector Sheet
2640 Mower Deck Hub Assy.
2641 Mower Deck Hub Sub-Assy.
2642 Mower Deck Hub
2645 Blade Shaft Weldment
2647 Blade Washer
2648 Deck Hub Key
2668 Stiffener
2823 Oil Drain Assy.
3029 Front Grommet
3120 Nylon Shoulder Bshg.
3123 Control Pin
3129 Plastic Tube Closure
3502 Hand Grip
3504 Double Ball Joint
3507 Floor Pad -Long
3508 Floor Pad -Short
3511 Adhesive Bumper Pad
3521 Engaging Cam Mount Bshg.
3531 Decal-Operating Inst.
3532 Decal-Blade Drive
3533 Decal-Cutting Height
3536 Warning Label-Danger
4005B Throttle Cable
4006-2 Solenoid-Starter Cable
4006-8 Solenoid-Battery Cable
4007-1 Battery-12V
4009 Wire Clip(not shown)
4013 Wire Tie (not shown)
4047 Seat Switch
4067 Ignition Switch
4067A Switch Key (for 4067)
4075 10 AMP Fuse
4079 Body Switch
4092 Fuse Holder
4109 Rear Wiring Loom
4115 Wiring Kit
4122 Body Wiring Loom
4124 Solenoid
4148 Seat Angle
5005 Discup
5007 Cone Frame
5009R Cradle
5009L Cradle
5012 Cradle Shaft
5013 Cone Frame Shaft
5015 24T Sprocket
5016 Molded Cone
5018 9T Sprocket-Narrow
5019 Transaxle Chain
5021 9T Sprocket-Wide
5024-1 Cradle Spring
5028 Transaxle Bearing
5036 Pivot Spring
5046 Positive Neutral R
5047 Positive Neutral S
5053 Brake Arm Retainer
6059 Flat Idler Pulley
6089 Engaging Handle
6107 Deck Pin
6136-2 Engaging Cam Weld.
6159 Stabilizer Arm Wel
Loading...