Page 1
Ditec CROSS18-19
Sliding gates automation
(original instructions)
www.ditecentrematic.com
IP1984E EN
Technical Manual
Page 2
24
IP1984EEN - 2015-09-22
Page 3
25
IP1984EEN - 2015-09-22
Index
Caption
Subject Page
1. General safety precautions 26
2. Declaration of incorporation of partly completed machinery 27
2.1 Machinery Directive 27
3. Technical data 28
3.1 Operating instructions 28
4. Standard installation 29
5. Dimensions 30
6. Main components 30
7. Installation 31
7.1 Preliminary checks 31
7.2 Base plate fastening 32
7.3 Geared motor installation 33
7.4 Rack installation 34
7.5 Lever stop installation and adjustment 35
7.6 Magnetic limit switches installation and adjustment 35
7.7 Rotary stop installation and adjustment 36
7.7 Chain drive kit installation 37
8. Electrical connections 38
9. Routine maintenance plan 38
Operating instructions 39
i
This symbol indicates instructions or notes regarding safety issues which require particular attention.
This symbol indicates informations which are useful for correct product function.
Page 4
26
IP1984EEN - 2015-09-22
1. General safety precautions
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed in accordance with
Good Working Methods and in compliance with applicable regulations.
Before installing the product, carefully read the instructions.
Bad installation could be hazardous.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-
ment or left within reach of children, as these are a potential source of hazard.
Before installing the product, make sure it is in perfect condition.
Do not install the product in an explosive environment and atmosphere: gas or inflammable
fumes are a serious hazard risk.
Before installing the motors, make all structural changes relating to safety clearances and
protection or segregation of all areas where there is risk of being crushed, cut or dragged, and
danger areas in general.
Make sure the existing structure is up to standard in terms of strength and stability.
The motor manufacturer is not responsible for failure to use Good Working Methods in building
the frames to be motorized or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking
into account: applicable laws and directives, Good Working Methods, installation premises,
system operating logic and the forces developed by the motorized door.
The safety devices must protect any areas where the risk exists of being crushed, cut or gragged,
or where there are any other risks generated by the motorized door.
Apply hazard area notices required by applicable regulations.
Each installation must clearly show the identification details of the motorized door.
When necessary, connect the motorized door to a reliable earth system made in accordance
with applicable safety regulations.
During installation, maintenance and repair, interrupt the power supply before opening the lid
to access the electrical parts.
The protective casing of the automation must be removed by qualified personnel only.
To handle electronic parts, wear earthed antistatic conductive bracelets.
The motor manufacturer declines all responsibility in the event of component parts being
fitted that are not compatible with the safe an correct operation.
For repairs or replacements of products only original spare parts must be used.
The installer shall provide all information relating to automatic, manual and emergency operation of the motorized door, and provide the user with operating instructions.
Page 5
27
IP1984EEN - 2015-09-22
2. Declaration of incorporation of partly
completed machinery
2.1 Machinery Directive
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB with headquarters in Lodjursgatan 10, SE-261 44
Landskrona, Sweden
declares that the automation system for Ditec CROSS18-19 sliding gates:
- has been constructed to be installed on a manual door to construct a machine pursuant to
the Directive 2006/42/EC. The manufacturer of the motorized door shall declare conformity pursuant to the Directive 2006/42/EC (annex II-A), prior to the machine being put into
service;
- conforms to applicable essential safety requirements indicated in annex I, chapter 1 of the
Directive 2006/42/EC;
- conforms to the Low Voltage Directive 2006/95/EC;
- conforms to the Electromagnetic Compatibility Directive 2004/108/EC;
- technical documentation conforms to Annex VII-B to the Directive 2006/42/EC;
- technical documentation is managed by Marco Pietro Zini with offices in Via Mons. Banfi,
3 - 21042 Caronno Pertusella (VA) - ITALY;
- a copy of technical documentation will be provided to national competent authorities, following a suitably justified request.
Landskrona, 13-01-2013 Marco Pietro Zini
(BA President)
Pursuant to Machinery Directive (2006/42/EC) the installer who motorizes a door or gate has
the same obligations as the manufacturer of machinery and as such must:
- prepare the technical file which must contain the documents indicated in Annex V of the
Machinery Directive;
(The technical file must be kept and placed at the disposal of competent national authorities
for at least ten years from the date of manufacture of the motorized door);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery
Directive and deliver it to the customer;
- affix the EC marking on the motorized door in accordance with point 1.7.3 of Annex I of the
Machinery Directive.
Page 6
28
IP1984EEN - 2015-09-22
3. Technical data
Ditec CROSS18 Ditec CROSS18E Ditec CROSS18VE Ditec CROSS19V
Power supply 230 V~ 50 Hz 230 V~ 50 Hz 230 V~ 50 Hz 400 V~ 50 Hz
Absorption 3 A 3 A 3 A 1,2 A
Thrust 1200 N
1200 N
1200 N 1500 N
Door speed 0,2 m/s 0,2 m/s 0,2 m/s 0,2 m/s
Max run 11 m 20 m 20 m 20 m
Max door weight 1800 kg 1800 kg 1800 kg 1800 kg
Service class 4 - INTENSIVE 4 - INTENSIVE 4 - INTENSIVE 4 - INTENSIVE
Min number of
consecutive cycles
50 50 50 50
Intermittence
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Temperature min -20° C
max +55° C
min -20° C
max +55° C
min -20° C
max +55° C
min -20° C
max +55° C
Degree of protection
IP24D IP24D IP24D IP24D
Control panel E1A - LOGIC M E1A (incorporated) LOGICM
(incorporated)
E1T
3.1 Operating instructions
Service class: 4 (minimum 100 cycles a day for 10 years or 200 cycles a day for 5 years)
Use: INTENSIVE (For vehicle or pedestrian accesses to large condominiums, industrial or
commercial complexes and parking lots with very frequent use).
- Performance characteristics are to be understood as referring to the recommended weight
(approx. 2/3 of maximum permissible weight). A reduction in performance is to be expected
when the access is made to operate at the maximum permissible weight.
- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of use. During given time spans
product performance characteristics will be such as not to require any special maintenance.
- The actual performance characteristics of each automatic access may be affected by independent
variables such as friction, balancing and environmental factors, all of which may substantially
alter the performance characteristics of the automatic access or curtail its working life or parts
thereof (including the automatic devices themselves). When setting up, specific local conditions
must be duly borne in mind and the installation adapted accordingly for ensuring maximum
durability and trouble-free operation.
Page 7
29
IP1984EEN - 2015-09-22
4. Standard installation
Ref. Code Description
1 Ditec CROSS18
Ditec CROSS18E
Ditec CROSS18VE
Ditec CROSS19V
230V gearmotor with rotary limit switch
230V gearmotor with lever limit switch / built-in control panel
230V gearmotor with magnetic limit switch / built-in control panel
400V gearmotor with magnetic limit switch
2 GOL4
GOL4C
Transmitter
3 LAMP Flashing light
4 XEL5
LAN4
GOL4M
Key selector
Control keyboard
Codified via radio control keyboard
5 XEL2
LAB4
Photocells
Photocells IP55
6 SOFA-SOFB
GOPAV
Safety edge
Radio system for safety edges
7 LAB9 Magnetic loop detection device for traffic monitoring
A Connect the power supply to an approved omnipolar switch with an opening
distance of the contacts of at least 3mm (not supplied).
The connection to the mains must be made via an independent channel,
separated from the connections to command and safety devices.
1 A
4
7
2
6
3
5
5
Page 8
30
IP1984EEN - 2015-09-22
5. Dimensions
6. Main components
Ref. Code Description
8 Motor
9 Casing
10 Control panel
11 Manual release
12 Pinion
13 Rack stop
14 Rotary stop group
15 Lever stop group
16 Magnetic limit switch group
440
24058 142
375
205
115
13
12
10
11
8
9
14
8
9
10
11
15
12
10
11
8
9
1616
12
Page 9
31
IP1984EEN - 2015-09-22
7. Installation
7.1 Preliminary checks
The given operating and performance features can only be guaranteed with the use of DITEC
accessories and safety devices.Unless otherwise specified, all measurements are expressed in
millimetres (mm).
Check the stability of the wing (derailing and lateral falls) and the sliding wheels and that the upper
guides do not cause any friction.
The sliding guide must be securely fixed to the ground for the full length within the doorway and
must have no irregularities that could hinder the movement of the gate.
The opening and closing stops must be fitted.
If the gate has slits, make sure they are covered to prevent shearing points.
Safety device should be installed at the end of the wing to reduce the collision force.
NOTE: make sure that the gate can not exit the sliding guides and fall.
Page 10
32
IP1984EEN - 2015-09-22
7.2 Base plate position
- Insert the anchor ties onto the base plate and fix them with the supplied nuts.
- Make a concrete base with the anchor ties and base plate embedded, which must be level and
clean, following the measurements indicated in the diagram.
i
NOTE: If the concrete base is already present, fix the base plate with expansion bolts M8 (not supplied)
to allow height adjustment.
OPENING
130
X+20 [*]
70[**]
min
150
Ø50x2
90°
240
270
[*] CROSSCRI
X=40
[**]
OPENING
130
X+20 [*]
70[**]
min
60
Ø50x2
90°
240
270
[*] CROSSCRI
X=40
[**]
Page 11
33
IP1984EEN - 2015-09-22
- Release the gearmotor and remove the key (see OPERATING INSTRUCTIONS). Unscrew the two
front screws and remove the casing [9].
- Place the gearmotor onto the base plate.
- Gearmotor adjustment
Horizontally slide the gearmotor on the slots of the anchor brackets (max 10 mm).
Vertically with the four levelling screws [A].
7.3 Geared motor installation
WARNING: the gearmotor must be suitably raised from the ground to avoid flooding.
37
66102
X
A
10
10
A
37
66102
X
A
10
10
A
i
NOTA: during the vertical adjustment, keep the gearmotor slightly raised from the base plate so that the
rack can be fixed and subsequent adjustments are possible.
- Release the gearmotor (see OPERATING INSTRUCTIONS) and open the gate.
- Rest the rack onto the pinion and manually sliding the gate, fix it throughout its entire length.
- Once fixing is complete, vertically adjust the gearmotor to give a play of 2-3 mm between the
rack and the pinion.
- CROSS18 only. Between the rack and the rack stop must be a play of 3 mm.
- Secure the gearmotor with the nuts.
- Slightly lubricate the rack and pinion after assembly.
Manually check that the gate slides evenly and without friction.
7.4 Rack installation
110
2÷3
~3
CROSS18 only
13
Page 12
34
IP1984EEN - 2015-09-22
7.5 Lever stop installation and adjustment
7.6 Magnetic limit switches installation and adjustment
- Manually place the wing in the completely open position and fix the limit switch bracket [B] onto
the rack so that the upper lever stop exceed for 2/3 times the length of the bracket. Repeat the
operation with the wing fully closed.
- After having carried out a few manoeuvres, adjust the position of the limit switch bracket [B] so
that the gate stops about 20 mm before the opening and closing stop
- Manually place the wing in the completely open position and fix the stop bracket [A] onto the rack
so that the upper lever stop exceed for 2/3 times the length of the bracket. Repeat the operation
with the wing fully closed.
- After having carried out a few manoeuvres, adjust the position of the limit switch bracket [A] so
that the gate stops about 20 mm before the opening and closing stop.
15÷20
A
A
AA
OPENING
~20
B
BB
B
15÷20
OPENING
~20
Page 13
35
IP1984EEN - 2015-09-22
7.7 Rotary stop adjustment
- With the gate open, turn the screw [A] so that cam [MA] activates the opening microswitch.
- With the gate closed, turn the screw [C] so that cam [MC] activates the closing microswitch.
NOTE: with the gate opened to the left (gearmotor side view) the microswitches are inverted [A]
for closing [C] and opening.
- Adjust [A] and [C] so that the activation of the limit switch stops the gate approximately 20 mm
before the stop.
OPENING
~20
MC
MA
A
C
i
NOTE: make sure this occurs after having performed several operations.
Page 14
36
IP1984EEN - 2015-09-22
7.8 Chain drive kit installation
- Release the gearmotor (see OPERATING INSTRUCTIONS).
- Remove pinion for rack.
- Fix the pinion supporting plate [A] to the gearmotor.
- Insert the pinion [B] as illustrated in the diagram.
- Manually pass the chain between the pinions.
- Fix the cover plate [C].
- Manually move the wing into the open position and fix the brackets [D] onto the wing as illustrated
in the figure.
- Connect chain [E], which was previously assembled on the gearmotor, to tie rod [F] and fix it to
bracket [D].
- Fix bracket [D] on the opposite side of the gate. Connect the chain [E] to the tie rod [F] and fix
it to bracket [D] (cut the excess chain).
NOTE: make sure that the distance between the pinion centre [X] and tie rod [F] is correct when
the gate is fully open and closed.
- Secure the gearmotor with the nuts [G].
- Tighten the chain [E] with the tie rods [F].
- Slightly lubricate the chain [E] and pinions after assembly.
N.B.: Install the chain traction kit before securing the gearmotor to the base plate.
40
X
F
DEG
A
B
C
110
min 60
X
F
Page 15
37
IP1984EEN - 2015-09-22
Before connecting the power supply, make sure the plate data correspond to that of the
mains power supply.
An omnipolar disconnection switch with minimum contact gaps of 3 mm must be included in
the mains supply.
Check that upstream of the electrical installation there is an adequate residual current circuit
breaker and a suitable overcurrent cutout.
Use a H05RN-F 3G1,5 or H05RR-F 3G1,5 type electric cable and connect to the terminals L
(brown), N (blue) in the automation.
Connect the yellow-green earth wire to the appropriate terminal already connected to the motor.
Secure the cable using the special cable clamp and remove the outer sheath near the terminal
only.
Connection to the mains power supply, in the section outside the automation, is made with
independent channels and separated from the connections to the control and safety devices.
The channel must go into the automation through the holes on the base plate.
Make sure there are no sharp edges that may damage the power supply cable.
Make sure that the mains power supply (230 V) conductors and the accessory power supply
(24 V) conductors are separate.
8. Electrical connections
CROSS18 CROSS18E CROSS18VE CROSS19V
Control panel E1A - LOGICM E1A LOGIC M E1T
NOTE: the electrical connections and starting of the gearmotor are illustrated in the control panel installation manual.
i
17 14 12 11 00011234567892041UWV
460 V
140°C
M
3~
black
black
yellow
Brake
black
red
white
Opening limit switch
Cl
osing limiti switch
Release switch
blue
blue
POWER
SA
11
IN
J12
com
blue
black
Opening limit switch
Cl
osing limiti switch
Release switch
M1
1~
12
R1
RF
AUX
A
N
T
C
O
M
F1
TC TM
JR6
12
12 011
11
01568941
NCUWVLN
SO 6>4
NIO
PRG
JR4
JR10
JR3
1ON234
1
4
5
2
3
F
U
S
E
E1A
SIG
LN
W+B
-B M
Power suppl
y
230 V~ / 50 Hz
white
white
black
blue
Brake
25μF
POWER
SA
11
IN
J12
M1
1~
12
R1
RF
AUX
A
N
T
C
O
M
F1
TC TM
JR6
12
12 011
11 01568941NCUWVLN
SO 6>4
NIO
PRG
JR4
JR10
JR3
1ON234
1
4
5
2
3
F
U
S
E
E1A
SIG
LN
W+B
-B M
blue
25μF
com
Opening limit switch
Cl
osing limiti switch
Release switch
Power suppl
y
230 V~ / 50 Hz
white
black
white
black
Brake
blue
TM
RF
AUX
AUX
JR6
POWER
SA
IN
11
12
F1
F2
TC RP TR R1
OM=OFF
J7
15 14 13 12 11
00112345678920 41
UWVXZYLN
D5 S5 JT
NIO
SO
JR10
JR4
EO
1ON23456
1
4
2
F
U
S
E
F
U
S
E
LOGICM
M1
1~
LN
W+B
-B M
com
blue
black
Opening limit switch
Cl
osing limiti switch
Release switch
Power suppl
y
230 V~ / 50 Hz
white
white
black
Brake
blue
CROSS18
CROSS18E
CROSS18VE
CROSS19V
Page 16
38
IP1984EEN - 2015-09-22
9. Routine maintenance plan
Perform the following operations and checks every 6 months according to intensity of use of the
automation.
- Visually check that the gate, the fixing brackets and existing structure have suitable mechanical
strength and are in good condition.
- Check the gate-gearmotor alignment, the distance (2-3 mm) between the throat of the pinion
and the crest of the rack.
- Clean the wheel’s sliding guide, the rack and pinion of the gear motor and slightly lubricate
the rack and pinion of the gearmotor. Manually check that the gate slides evenly and without
friction.
Connect the power supply and block the gearmotor (see RELEASE INSTRUCTIONS operations):
- Check that the limit switches are working correctly.
- Check the power adjustment.
- Check that all control and safety functions are working correctly.
WARNING: For spare parts, see the spares price list.
i
Page 17
39
IP1984EEN - 2015-09-22
The following precautions are an integral and essential part of the product and must be
supplied to the user.
Read them carefully since they contain important information on safe installation, use and maintenance.
These instructions must be kept and forwarded to all possible future users of the system.
This product must only be used for the specific purpose for which it was designed.
Any other use is to be considered improper and therefore dangerous.
The manufacturer cannot be held responsible for any damage caused by improper, incorrect or
unreasonable use.
This product should not be used by people (including children) with reduced physical, sensory or
mental capabilities or lack of experience and knowledge unless they have been given supervision
or instructions concerning the use of the appliance by a person responsible for their safety.
Avoid operating in the proximity of the hinges or moving mechanical parts.
Do not enter within the operating range of the motorized door while it is moving.
Do not block the movement of the motorized door since this may be dangerous.
Do not allow children to play or stay within the operating range of the motorized door.
Keep remote controls and/or any other control devices out of the reach of children in order to
avoid possible
involuntary activation of the motorized door.
In the event of fault or malfunctioning of the product, turn off the power supply switch, do not
attempt to repair or intervene directly and contact only qualified personnel.
Failure to comply with the above may cause a dangerous situation.
All cleaning, maintenance or repair work must be carried out by qualified personnel.
To ensure that the system works efficiently and correctly, the manufacturer’s indications must be
complied with and routine maintenance of the motorized door must be performed by qualified
personnel.
In particular, regular checks are recommended in order to verify that the safety devices are ope-
rating correctly.
All installation, maintenance and repair work must be documented and made available
to the user.
For the correct disposal of electric and electronic equipment, waste batteries and accumulators,
the user must take such products to the designated municipal collection facilities.
Ditec CROSS18-19
Sliding gates
Operating instructions
General safety precautions
DETACH AND DELIVER TO THE CUSTOMER
Page 18
40
IP1984EEN - 2015-09-22
In the event of a fault or power failure, insert the key
and turn it anticlockwise and completely open the
hatch. Open the gate manually.
To block the gate again, close the hatch, turn the key
clockwise and remove the key.
Manual release instructions
WARNING: the door wing block and release operations must be performed with the motor idle.
When the hatch is closed, but the key is still horizontal, the release micro remains open and all gate
operations are prevented.
For any problems and/or information, contact the support service.
Installer’s stamp Operator
Date of intervention
Technician’s signature
Customer’s signature
Intervention:
DETACH AND DELIVER TO THE CUSTOMER
90°
90°
OFF
ON
Entrematic Group AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
www.ditecentrematic.com
Page 19
41
IP1984EEN - 2015-09-22
All the rights concerning this material are the exclusive property of Entrematic Group AB. Although the contents of this publication have been drawn up with the greatest care, Entrematic Group AB cannot be held
responsible in any way for any damage caused by mistakes or omissions in this publication.
We reserve the right to make changes without prior notice. Copying, scanning and changing in any way are
expressly forbidden unless authorised in writing by Entrematic Group AB.
Page 20
IP1984EEN - 2015-09-22
Entrematic Group AB
Lodjursgatan 10
SE-261 44, Landskrona
Sweden
www.ditecentrematic.com
Loading...