Ditec CROSS18-19
Sliding gates automation
(original instructions)
www.ditecentrematic.com
IP1984E EN
Technical Manual
24
IP1984EEN - 2015-09-22
25
IP1984EEN - 2015-09-22
Index
Caption
Subject Page
1. General safety precautions 26
2. Declaration of incorporation of partly completed machinery 27
2.1 Machinery Directive 27
3. Technical data 28
3.1 Operating instructions 28
4. Standard installation 29
5. Dimensions 30
6. Main components 30
7. Installation 31
7.1 Preliminary checks 31
7.2 Base plate fastening 32
7.3 Geared motor installation 33
7.4 Rack installation 34
7.5 Lever stop installation and adjustment 35
7.6 Magnetic limit switches installation and adjustment 35
7.7 Rotary stop installation and adjustment 36
7.7 Chain drive kit installation 37
8. Electrical connections 38
9. Routine maintenance plan 38
Operating instructions 39
i
This symbol indicates instructions or notes regarding safety issues which require particular attention.
This symbol indicates informations which are useful for correct product function.
26
IP1984EEN - 2015-09-22
1. General safety precautions
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed in accordance with
Good Working Methods and in compliance with applicable regulations.
Before installing the product, carefully read the instructions.
Bad installation could be hazardous.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-
ment or left within reach of children, as these are a potential source of hazard.
Before installing the product, make sure it is in perfect condition.
Do not install the product in an explosive environment and atmosphere: gas or inflammable
fumes are a serious hazard risk.
Before installing the motors, make all structural changes relating to safety clearances and
protection or segregation of all areas where there is risk of being crushed, cut or dragged, and
danger areas in general.
Make sure the existing structure is up to standard in terms of strength and stability.
The motor manufacturer is not responsible for failure to use Good Working Methods in building
the frames to be motorized or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking
into account: applicable laws and directives, Good Working Methods, installation premises,
system operating logic and the forces developed by the motorized door.
The safety devices must protect any areas where the risk exists of being crushed, cut or gragged,
or where there are any other risks generated by the motorized door.
Apply hazard area notices required by applicable regulations.
Each installation must clearly show the identification details of the motorized door.
When necessary, connect the motorized door to a reliable earth system made in accordance
with applicable safety regulations.
During installation, maintenance and repair, interrupt the power supply before opening the lid
to access the electrical parts.
The protective casing of the automation must be removed by qualified personnel only.
To handle electronic parts, wear earthed antistatic conductive bracelets.
The motor manufacturer declines all responsibility in the event of component parts being
fitted that are not compatible with the safe an correct operation.
For repairs or replacements of products only original spare parts must be used.
The installer shall provide all information relating to automatic, manual and emergency operation of the motorized door, and provide the user with operating instructions.
27
IP1984EEN - 2015-09-22
2. Declaration of incorporation of partly
completed machinery
2.1 Machinery Directive
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB with headquarters in Lodjursgatan 10, SE-261 44
Landskrona, Sweden
declares that the automation system for Ditec CROSS18-19 sliding gates:
- has been constructed to be installed on a manual door to construct a machine pursuant to
the Directive 2006/42/EC. The manufacturer of the motorized door shall declare conformity pursuant to the Directive 2006/42/EC (annex II-A), prior to the machine being put into
service;
- conforms to applicable essential safety requirements indicated in annex I, chapter 1 of the
Directive 2006/42/EC;
- conforms to the Low Voltage Directive 2006/95/EC;
- conforms to the Electromagnetic Compatibility Directive 2004/108/EC;
- technical documentation conforms to Annex VII-B to the Directive 2006/42/EC;
- technical documentation is managed by Marco Pietro Zini with offices in Via Mons. Banfi,
3 - 21042 Caronno Pertusella (VA) - ITALY;
- a copy of technical documentation will be provided to national competent authorities, following a suitably justified request.
Landskrona, 13-01-2013 Marco Pietro Zini
(BA President)
Pursuant to Machinery Directive (2006/42/EC) the installer who motorizes a door or gate has
the same obligations as the manufacturer of machinery and as such must:
- prepare the technical file which must contain the documents indicated in Annex V of the
Machinery Directive;
(The technical file must be kept and placed at the disposal of competent national authorities
for at least ten years from the date of manufacture of the motorized door);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery
Directive and deliver it to the customer;
- affix the EC marking on the motorized door in accordance with point 1.7.3 of Annex I of the
Machinery Directive.
28
IP1984EEN - 2015-09-22
3. Technical data
Ditec CROSS18 Ditec CROSS18E Ditec CROSS18VE Ditec CROSS19V
Power supply 230 V~ 50 Hz 230 V~ 50 Hz 230 V~ 50 Hz 400 V~ 50 Hz
Absorption 3 A 3 A 3 A 1,2 A
Thrust 1200 N
1200 N
1200 N 1500 N
Door speed 0,2 m/s 0,2 m/s 0,2 m/s 0,2 m/s
Max run 11 m 20 m 20 m 20 m
Max door weight 1800 kg 1800 kg 1800 kg 1800 kg
Service class 4 - INTENSIVE 4 - INTENSIVE 4 - INTENSIVE 4 - INTENSIVE
Min number of
consecutive cycles
50 50 50 50
Intermittence
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Temperature min -20° C
max +55° C
min -20° C
max +55° C
min -20° C
max +55° C
min -20° C
max +55° C
Degree of protection
IP24D IP24D IP24D IP24D
Control panel E1A - LOGIC M E1A (incorporated) LOGICM
(incorporated)
E1T
3.1 Operating instructions
Service class: 4 (minimum 100 cycles a day for 10 years or 200 cycles a day for 5 years)
Use: INTENSIVE (For vehicle or pedestrian accesses to large condominiums, industrial or
commercial complexes and parking lots with very frequent use).
- Performance characteristics are to be understood as referring to the recommended weight
(approx. 2/3 of maximum permissible weight). A reduction in performance is to be expected
when the access is made to operate at the maximum permissible weight.
- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of use. During given time spans
product performance characteristics will be such as not to require any special maintenance.
- The actual performance characteristics of each automatic access may be affected by independent
variables such as friction, balancing and environmental factors, all of which may substantially
alter the performance characteristics of the automatic access or curtail its working life or parts
thereof (including the automatic devices themselves). When setting up, specific local conditions
must be duly borne in mind and the installation adapted accordingly for ensuring maximum
durability and trouble-free operation.
Loading...