DIRTDEVIL M086020 User Manual

OWNER’S MANUAL

Operating and Servicing Instructions

Find GENUINE Replacement Parts at

www.dirtdevil.com

• Please read these instructions carefully before using your Upright.

• Let us help you put your vacuum together or answer any questions, call:

This cleaner uses the following parts:

BELT STYLE

BAG TYPE

THIS VACUUM CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY.

IMPORTANT SAFETY INSTRUCTIONS

When you use an appliance, basic precautions should always be followed, including the following:

• READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

• ALWAYS FOLLOW THESE SAFETY INSTRUCTIONS.

• BRING VACUUM CLEANER TO UPRIGHT POSITION WHEN USING THE HOSE AND ATTACHMENTS.

• DO NOT LEAVE VACUUM CLEANER UNATTENDED WHEN PLUGGED IN.

• REGULARLY CHECK THE FILTER TO CLEAN OR REPLACE.

• WARNING: DO NOT USE SHARP OBJECTS TO CLEAN OUT THE HOSE SINCE THEY COULD CAUSE DAMAGE.

• OCCASIONALLY REMOVE BRUSH AND CLEAN DEBRIS FROM END CAPS TO KEEP BRUSH ROTATING SMOOTHLY.

• WARNING: THE CORDS, WIRES, AND/OR CABLES SUPPLIED WITH THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD OR LEAD COMPOUNDS, KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USING.

WARNING: TO REDUCE THE RISK OF FIRE,

1-800-321-1134 (USA & Canada) www.dirtdevil.com

WARNING:

Cleaner assembly may include small parts. Small parts can present a choking hazard.

Warranty Registration

• Online at: www.dirtdevil.com

• Mail: Royal Appliance Mfg 7005 Cochran Rd. Glenwillow, Ohio 44139

Español - página E1

For quick reference, please record your vacuum information below.

Model #: Mfg. Code:

(Mfg. code located on the lower backside of cleaner)

6/06

ELECTRIC SHOCK OR INJURY:

• Do not leave appliance when plugged in. Unplug from outlet when not in use

and before servicing.

• Do not use outdoors or on wet surfaces. Electrical shock could occur.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center for inspection. Call 1-800-321-1134 for the nearest service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Do not use without dust bag and/or filters in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

• Keep the vacuum cleaner on the floor. Only the hand-held vacuum cleaners may be set on furniture.

• Vacuum cleaner must be in the upright position to lift the rotating brush off the carpet when doing above floor cleaning.

• Do not use an extension cord with this vacuum cleaner.

• Store the vacuum cleaner indoors. Put the vacuum cleaner away after use to prevent tripping accidents.

• Using improper voltage may result in damage to the motor and possible injury to the user. Proper voltage is listed on the cleaner plate.

• Only use attachments and hoses recommended by the manufacturer. Use the

vacuum cleaner only as stated in this manual.

• Unplug before connecting *Power Brush Tool.

*NOT AVAILABLE ON ALL MODELS

SAVE THESE INSTRUCTIONS

WARNING:

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

CONGRATULATIONS

You are now the proud owner of a Dirt Devil®. We trust your new purchase will bring you many years of satisfaction.

Our company has designed and developed this product with you in mind. We are very proud of our products and hope that you are equally satisfied

with their quality and performance. Thank you for your support of Dirt Devil® products.

Visit our website at www.dirtdevil.com

TABLE OF CONTENTS

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2, 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5

How to Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

Tool Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

How To Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

Floor/Carpet Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

Above Floor Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

Paper Bag: Removal & Replacement . . . . . . . . . . . . . . . . . . . . . Page 8

Filter: Removal & Replacement . . . . . . . . . . . . . . . . . . . . . . . . . Page 8, 9

Belt or Brushroll: Removal & Replacement . . . . . . . . . . . . . . . . . Page 10

Lightbulb: Removal & Replacement . . . . . . . . . . . . . . . . . . . . . . Page 11

Transporting Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12

Your cleaner contains a thermal protective device to shut off the motor to avoid overheating. If this happens, turn switch off and unplug the cleaner. Inspect the exhaust, inlet, hose, and filters for any blockage. Change bag if full. After approximately 30 minutes the motor will have cooled and the vacuum will be ready to use. NOTE: The cleaner must remain unplugged during the 30 minute

cooling period.

LIMITED WARRANTY

To the consumer, Royal Appliance Mfg. Co. warrants this vacuum cleaner to be free of defects in material or workmanship commencing upon the date of the original purchase. Refer to your vacuum cleaner carton for the length of warranty and save your original sales receipt to validate start of warranty period.

If the vacuum cleaner should become defective within the warranty period, we will repair or replace any defective parts free of charge. The complete machine must be delivered prepaid to any ROYAL® Authorized Sales & Warranty Service Station. Please include complete description of the problem, day of purchase, copy of original sales receipt and your name, address and telephone number. If you are not near a Warranty Station, call the factory for assistance at USA & Canada: 1-800-321-1134. Use only genuine Royal® replacement parts.

The warranty does not include unusual wear, damage resulting from accident or unreasonable use of the vacuum cleaner. This warranty does not cover brushes, bags, flat belts, filters and bulbs. This warranty does not cover unauthorized repairs. This warranty gives you specific legal rights and you may also have other rights (Other rights may vary from state to state in the USA).

IMPORTANT: USE ONLY GENUINE ROYAL® REPLACEMENT PARTS. NOTE: TO REGISTER YOUR PRODUCT, RETURN YOUR WARRANTY CARD OR REGISTER ONLINE AT WWW.DIRTDEVIL.COM.

FEATURES

HOW TO ASSEMBLE

TOOL REQUIRED: PHILLIPS SCREWDRIVER

BACKFRONT

HANDLE ASSEMBLY

FRONT

1. Handle Grip

2. Power Brush Tool

3. Front Panel Release Lever

4. Front Panel

5. Filter Cage

6. Headlight

7. Scuff Guard™ Bumper

8. Brush View Window

9. Carpet Height Adjustment Knob

10. Hose Grip

11. Full Bag Indicator

15 16

Pull release lever on front panel to remove front panel from body of cleaner.

Secure the handle by installing the two (2) screws provided into the holes on the front of the unit. Make sure to fully tighten screws.

Stand unit in upright position and insert handle into the hole on the top of the back panel.

HOSE ASSEMBLY

Place hose onto hose wrap (located on back of handle) to secure.

Insert carry handle into back panel opening at the top of the back panel.

Insert the hose grip into the side of the cleaner. Press down firmly to secure. NOTE: A slight

twisting motion may help.

TOOL STORAGE CORD STORAGE

BACK

12. Upper Cord Wrap with Quick Cord Release

13. Long Power Cord

14. Hose Wrap/Carry Handle

15. Crevice Tool

(inside extension wand)

16. Extension Wand

17. Lower Cord Wrap

18. Stretch Hose

19. Swivel Casters

20. Handle Release Pedal

21. On/Off Pedal

22. Dust Brush

™

Attach front panel by aligning 2 tabs on front panel with 2 slots on body of cleaner. Secure front panel by snapping into place.

BACK FRONT

Attach Tools: Place dust brush (A) onto peg on the tool caddy with bristles facing out. Slide the extension wand (B)/ crevice tool (C) (stored inside of extension wand) through the ring on the back right side of tool caddy (Diagram 4). Clip Power Brush Tool (D) into the power brush tool caddy on the front of the handle (Diagram 4a).

4a.

C B

For tidy cord storage, wrap cord around hooks on back of cleaner. The quick cord release turns for easy access to the cord.

HOW TO OPERATE

BAG T YPE

WARNING: FULLY ASSEMBLE BEFORE OPERATING. NOTE: Cleaner must be in the upright position to lift the rotating brush off the carpet when cleaning above the

floor.

CARPET SETTINGS

CARPET CLEANING

NOTE: The cleaner may be in the upright or operating position to adjust carpet setting. ADJUSTING IN THE UPRIGHT POSITION: Rotate the knob to the desired setting.

NOTE: The knob will rotate easily. Once the carpet setting is selected, and the cleaner

placed in the operating position, the setting will be in the correct position.

ADJUSTING IN THE OPERATING POSITION: Rotate the knob to the desired setting. NOTE: The knob will rotate with some resistance. The nozzle will raise and lower as the

knob is rotated.

PAPER BAG: REMOVAL & REPLACEMENT

WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING. NOTE: Unplug cleaner before changing paper bag. Cleaner must have paper bag in place at all times. You can

tell your bag needs replacing when you experience less suction or when the Full Bag Indicator changes to yellow or red. Do not exceed marked fill line on paper bag. Different types of dirt may require bag replacement more often.

FULL BAG INDICATOR: When the Full Bag Indicator window changes to yellow or red, it may be time for a new paper bag. Check the paper bag, and if full, replace as described below. If not, the cleaner may have a clogged dirt passage (See “Trouble Shooting” Pg. 12).

For Bag Type U replacements, please visit our website at www.dirtdevil.com to buy online or call customer service at 1-800-321-1134.

REMOVE OLD BAG

Raised

Locking

Tabs

TO INSTALL NEW BAG

Hole

Raised

Locking

Tabs

ABOVE FLOOR CLEANING

Plug cord into electrical outlet. Turn cleaner “ON”. Power Pedal located on lower left side of back of unit.

Put cleaner in its upright position. Remove the hose from the side of the cleaner by pulling out the hose grip. NOTE: A slight

twisting motion my help.

With foot, depress the handle release pedal on the lower back side of the cleaning nozzle. NOTE: Rotating brush

could cause area rug fringe to become tangled within cleaner. Use caution when vacuuming throw rugs with fringe.

Choose any of the handy accessories or use the hose alone. Simply push the attachment firmly onto the end of the wand or hose grip. To remove tool, twist and pull apart gently.

Pull release lever on front panel to remove front panel.

Grasp cardboard collar of paper bag with both hands and pull past raised locking tabs on the dirt tube. Dispose of old paper bag.

I M P O R T A N T : Expand bag away from hole before installing. Press in opening to clear paper away from hole.

Grip cardboard collar and push past raised locking tabs on dirt tube with both hands.

Fold bag inward about 3” from bottom to rest on top of bag support posts. Reattach front panel. NOTE: Be sure not to let the bag get caught between the front and back panel.

FILTER: REMOVAL & REPLACEMENT

WARNING: UNPLUG CLEANER BEFORE CHANGING FILTER. NOTE: Filter should be cleaned as needed.

For Bag Chamber filter replacements, please visit our website at www.dirtdevil.com to buy online or call customer service at 1-800-321-1134.

BAG CHAMBER FILTER (INTERNAL)

Located under the paper bag.

Remove front panel.

Lift up on front edge and pull towards you to remove. Shake or brush excess dirt off of filter. Slide filter pad back into position. Replace front panel.

FILTER REMOVAL & REPLACEMENT: CONTINUED

BELT STYL E

TOOL REQUIRED: PHILLIPS SCREWDRIVER

WARNING: UNPLUG CLEANER BEFORE CHANGING FILTER. NOTE: Filter should be cleaned as needed.

For Exhaust filter replacements, please visit our website at www.dirtdevil.com to buy online or call customer service at 1-800-321-1134.

EXHAUST FILTER

Located on the side of the cleaner.

BELT OR BRUSHROLL: REMOVAL & REPLACEMENT

TOOL REQUIRED: PHILLIPS OR FLATHEAD SCREWDRIVER

WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING.

For Belt Style 5 replacements, please visit our website at www.dirtdevil.com to buy online or call customer service at 1-800-321-1134.

TO REMOVE OLD BELT

Remove screw from filter cage.

Tap the filter on the inside of a garbage can to remove excess dust and dirt. DO NOT APPLY WATER TO PLEATED FILTER!

Pivot filter cage away from body of cleaner then remove.

Return HEPA filter cartridge to cleaner.

Grasp HEPA filter cartridge and remove.

Return filter cage to cleaner by inserting tabs on corners of filter cage into slots on side of the cleaner. Rotate back into place and secure with the one screw.

Lay cleaner flat and flip cleaner to expose nozzle base. Base should lay flat and face up. To remove nozzle guard, use Phillips screwdriver to remove the four (4) screws. Arrows show location of screws.

TO REPLACE NEW BELT

Slide belt onto motorshaft. Place new belt in area of brushroll without

Motor

Shaft

bristles (see inset).

Secure by aligning the three (3) tabs in the base slots. To reattach nozzle guard, rotate/pivot back into position.

Rotate/pivot the nozzle guard and pull off.

Lift and remove brushroll. Dispose of old belt.

With new belt in place, pull and slide brushroll into nozzle making sure that the brushroll end caps are in the correct orientation (see inset). Rotate brushroll manually to make sure belt is properly aligned.

Replace all four (4) screws to secure nozzle guard. NOTE: Make sure

bumper is secure before replacing screws.

LIGHTBULB: REMOVAL & REPLACEMENT

TOOL REQUIRED: PHILLIPS OR FLATHEAD SCREWDRIVER WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR REPLACING LIGHTBULB.

This cleaner uses a common automotive lamp #906, 13.0 volts. For bulb replacement call 1-800-321-1134 or your local auto parts store.

Remove front panel.

Pull bulb out of socket to remove. Push bulb into socket to replace.

2a.

Reattach headlight lens panel and replace both screws to secure into place. Reattach front panel.

Lay cleaner flat. Unscrew the two (2) screws on the headlight lens panel (Diagram 2). Lift cover to remove (Diagram 2a).

HOW TO TRANSPORT CLEANER

Use the carrying handle on the back of the cleaner to move cleaner from room to room (See Pg. 5, #13 for location).

NOTE: Do not push cleaner forward while leaning on back casters, pull cleaner on back casters, or attempt to lift cleaner using upper handle.

GENERAL MAINTENANCE

DEBRIS REMOVAL/POWER BRUSH TOOL

TROUBLESHOOTING GUIDE

WARNING: TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING

PROBLEM POSSIBLE REASON POSSIBLE SOLUTION

Cleaner won’t run

Cleaner won’t pick-up or low suction

Dust escaping from cleaner

Cleaner tools won’t pick-up

Headlight not working

Cleaner is difficult to push

Belt burns or breaks

1. Power cord not firmly plugged into outlet.

2. Blown fuse or tripped breaker.

3. Needs service.

4. Thermal Protector activated.

1. Paper bag is not opened.

2. Paper bag full.

3. Brushroll worn.

4. Broken or worn belt.

5. Clogged filter pad.

6. Nozzle/dirt passage clogged.

7. Carpet height setting is incorrect.

8. No paper bag.

9. Bag inlet clogged.

1. Paper bag full.

2. Bag not installed correctly.

3. Puncture/hole in paper bag.

4. No bag in cleaner.

5. Hose not installed correctly.

1. Hose clogged.

2. Bag inlet clogged.

3. Paper bag full.

4. No bag in cleaner; filter clogged.

1. Bulb burnt out.

2. Loose electrical wires.

1. Carpet height setting is incorrect.

1. Brush may be jammed with debris.

2. Brush End Caps are clogged with debris.

3. Carpet Height Setting is incorrect.

4. Belt is broken.

1. Plug unit in firmly.

2. Check fuse or breaker in home. Replace fuse/reset breaker.

3. Take to service center or call 1-800-321-1134.

4. Allow cleaner to cool - Pg. 3.

1. Insert finger into hole and push paper away from opening - Pg. 8.

2. Replace paper bag - Pg. 8.

3. Replace brushroll - Pg. 10.

4. Replace belt - Pg. 10.

5. Clean or replace filter - Pg. 8 & 9.

6. Remove base nozzle cover - Pg. 10; remove obstruction OR remove hose - Pg. 6.

7. Set carpet height adjustment to appropriate setting for carpet being cleaned - Pg. 7.

8. Clean filter - Pg. 8, install bag - Pg. 7.

9. Remove hose & paper bag and clean inlet Pg. 6 & 8.

1. Replace paper bag - Pg. 8.

2. Review paper bag installation - Pg. 8.

3. Replace paper bag - Pg. 8. Clean/Replace filter Pg. 8 & 9.

4. Install bag - Pg. 8, clean filter - Pg. 8 & 9.

5. Review hose installation - Pg. 6.

1. Remove hose and tools; remove obstruction Pg. 6.

2. Remove hose & paper bag and clean inlet Pg. 6 & 8.

3. Replace paper bag - Pg. 8.

4. Install paper bag - Pg. 8, clean filter - Pg. 8 & 9.

1. Replace bulb - Pg. 11.

2. Call 1-800-321-1134 for nearest authorized Royal® Dealer.

1. Set carpet height adjust lever to appropriate setting for carpet being cleaned - Pg. 7.

1. Remove brush - Pg. 10. Clean brush or debris.

2. Remove brush. Determine if End Caps rotate freely. If not, replace brushroll - Pg. 10.

3. Set Carpet Height adjustment to appropriate setting for carpet being cleaned - Pg. 7.

4. Replace belt - Pg. 10.

LOCKING RING

Rotate locking ring 180˚ and turn Power Brush Tool over.

Pivot lower housing and remove clog.

To reassemble, be sure tabs are engaged. Pivot the lower housing closed.

ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE

CUSTOMER SERVICE (1-800-321-1134)

In the event that further assistance is required, see your Yellow Pages for an authorized Royal® Dealer or visit our website at www.dirtdevil.com. Costs of any transportation to and from any place of repair are to be paid by the owner. The service parts used in this unit are easily replaced and readily available from an authorized Royal® Dealer or retailer. Always identify your cleaner by the model number and manufacturing code when requesting information or ordering replacement parts. (The model number appears on the bottom of the cleaner.)

+ 12 hidden pages

DIRTDEVIL M086020 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual