Dirt Devil Bandit DDBBC User Manual

Download

Page 1

Bagged Cylinder

USER GUIDE

Dirt Devil Service Line:

AU: 1300 361 505 / NZ: 0800 800 900

LET’S GO.

What’s your Dirt Devil’s model number?

D D B B C

What’s your serial number?

Note these down in case you need them in future. Please keep instructions for further use.

dirtdevil.com.au DDB BC

(Located on the base of the machine)

Page 2

Dirt Devil Service Line: AU: 1300 361 505

NZ: 0800 800 900 dirtdevil.com.au

Page 3

MACHINE OVERVIEW

Filters

Pre-motor Filter Post-motor Filter

Accessories

CYLINDER

1. Bag full indicator

2. Lid release button

3. Hose inlet

4. Cord rewind button (press down on handle)

5. Carry handle

6. On/off button, variable power dial

7. Floor tool parking slot

8. Plug

9. Post-motor ﬁlter cover

dirtdevil.com.au 2

ACCESSORIES

10. 3-in-1 crevice tool, dusting brush and upholstery tool

11. Hose

12. Combination tool

13. Telescopic wand

FILTERS

• Pre-motor lter (located inside

the dust bag cavity, behind the dust bag)

• Post-motor lter (located

behind the exhaust ﬁlter cover)

Page 4

dirtdevil.com.au

SAFETY INSTRUCTIONS

THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. IF USED COMMERCIALLY WARRANTY IS VOI D.

When using the vacuum cleaner basic safety precautions should always be observed, including the following:

1. Only use the vacuum cleaner indoors on dry surfaces.

2. Turn off the on/off switch on the vacuum cleaner controls before disconnecting or connecting from the mains supply.

3. Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose and accessories.

4. Children should be supervised to ensure that they do not play with the appliance.

5. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

6. Cleaning and maintenance shall not be made by children.

7. The appliance should only be used as described in this user guide.

8. Only Dirt Devil recommended attachments should be used with this appliance.

9. Do not use this vacuum cleaner if it has been dropped, damaged, left outdoors or dropped into water. Do not use this vacuum cleaner with a damaged cord or plug.

10. Do not pull or carry this appliance by the cord. Do not use the cord as a handle, close a door on the cord or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.

11. Do not handle the plug or the vacuum cleaner with wet hands.

12. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.

13. Do not pick up any hot coals, ash, cigarette butts, matches or any hot, smoking or burning objects.

14. Do not pick up any flammable or combustible materials (lighter fluid, petrol, kerosene etc.) or use in the presence of explosive liquids or vapours.

15. Do not vacuum harmful or toxic material (chlorine, bleach, ammonia, drain cleaner etc.).

16. Do not vacuum hard or sharp objects such as glass, nails, screws, coins etc.

1 7. Do not vacuum plaster dust, concrete dust or any other

building or vitreous materials.

18. Do not vacuum baking soda or any other powder-based carpet refresher or deodoriser.

19. Use only SAA approved 10amp extension cords. Non-approved cords may overheat. Care should be taken to arrange the cord so that the cord cannot be tripped over.

20. Store the vacuum cleaner in a cool, dry area.

21. Do not put any objects into openings. Do not use with any openings blocked and do not restrict airflow. Keep all openings free of dust, lint, hair or anything that might reduce airflow.

22. Do not use the vacuum cleaner with blocked filters and without all of the filters in place.

23. Take extra care when positioning the vacuum cleaner on the stairs.

24. Please ensure that the brushbar is turned off when you are vacuuming on the stairs.

25. Keep vacuuming area well lit.

WARNING: Always switch off and unplug the vacuum

cleaner from the electrical socket before assembling, opening or emptying the dirt container, or before connecting/disconnecting the attachments.

CAUTION: The vacuum cleaner is a very powerful unit.

Before plugging the cord into the electrical socket, make sure the switch is in the ‘off’ position.

IMPORTANT: If the inlet, hose or telescopic tube is

blocked, switch off the vacuum cleaner and remove the blockage(s) before re-starting the vacuum cleaner.

IMPORTANT: Dirt Devil recommends the use of Residual

Current Device Rating of 30mA or less.

IMPORTANT: It is very important that filters are kept clean

to obtain maximum performance from your vacuum cleaner. Not cleaning and not replacing your filters regularly can reduce the suction power and cause overheating and permanent damage to the vacuum cleaner.

NOTE: If the supply cord is damaged it must be replaced

by the manufacturer, or a similarly qualified person in order to avoid hazard, or invalidating the warranty.

IMPORTANT: The motor is equipped with a thermal cut-out. If

for any reason the unit should overheat (eg. from blocked nozzles, a full dust container or unclean filters), the thermostat will automatically turn off the switch. Should this occur, unplug the vacuum cleaner from the electrical socket and turn off the switch. Remove dirt container and empty. Clean filters. Allow the unit to cool for approximately one (1) hour. To re-start, plug into an electrical socket and switch back on.

DAMAGE TO THE VACUUM CLEANER CAUSED AS A DIRECT RESULT OF NOT ADHERING TO THE GENERAL SAFETY INFORMATION AND THE INSTRUCTIONS IN THIS USER GUIDE INVALIDATES THE WARRANTY

PLEASE KEEP THESE INSTRUCTIONS FOR FUTUR E REFERENCE

Dirt Devil Service Line: AU: 1300 361 505

NZ: 0800 800 900

Page 5

OPERATION

Assemble appliance and adjust accessories to surface

WARNING: Danger of injury! Only attach the accessory parts when the appliance is not connected

to the power supply.

CAUTION: Before assembling, make sure that the accessory part suits the surface to be cleaned.

NOTE: Twist the accessory part when connecting them to

the wand or hose so they are securely in place. Ensure that installed parts are secure by trying to pull them apart.

1. Assemble the appliance and accessory parts depending on the surface you want to vacuum clean (Fig. 1 – 10).

2. Ensure that the auxiliary air regulator is shut (Fig. 2).

3. If you use the telescopic tube (Fig. 3), adjust its

length (Fig. 4).

4. If you use the combination ﬂoor tool (Fig. 5), using the rocker switch, set it to the ﬂoor to be cleaned (Fig. 6 hard ﬂoor, Fig. 7 carpet).

3 4 6

Connect hose to telescopic wand.

Telescopic wand height adjust.

Attach hose to vacuum cleaner.

Combination ﬂoor tool.

Close auxiliary air regulator.

Rocker Switch

Hard ﬂoors.

9 10

Rocker Switch

Carpet.

Dusting brush.

dirtdevil.com.au 4

Crevice tool. Upholstery tool.

Page 6

dirtdevil.com.au

OPERATION

Vacuum cleaning

WARNING: Danger of injury! Check appliance and power cord before each use. A damaged appliance

or power cord must never be used.

CAUTION: Only use the appliance with all ﬁlters clean, undamaged, dry and correctly ﬁtted. Make sure

that no objects obstruct the telescopic tube, the suction hose or other openings.

1. Pull the cable out of the appliance (Fig. 11) and plug into a socket.

WARNING: Danger of electric shock! If the red marking shows retract the cord by pressing the cord

retract button to pull in the cord up to the yellow mark (Fig. 12) again.

2. Switch on the appliance using the on/off switch (Fig. 13).

3. Set the power to the setting that corresponds to the cleaning task. (Fig. 14).

NOTE: The auxiliary air regulator must be completely closed for vacuum cleaning. With the auxiliary air regulator

you can quickly reduce the suction power, to release objects (such as curtains) that have been sucked in.

4. Vacuum clean (Fig. 15).

WARNING: Danger of injury! When vacuum-cleaning stairs make sure that you always stand on a higher

level than the appliance.

WARNING: Keep the appliance out of the reach of children.

Dirt Devil Service Line: AU: 1300 361 505

NZ: 0800 800 900

Page 7

OPERATION

After use

click!

WARNING: Danger of injury! After vacuuming, switch off the appliance and wind up the power cord.

When winding up the cord keep the plug in your hand so that the cord does not cause injury.

CAUTION: Never store the appliance next to heat sources (e.g. stoves or radiators). Avoid exposing

it to direct sunlight. Store the appliance and accessories in a cool and dry location (Fig. 16 – 20).

CAUTION: If you intend to store the appliance for a long period of time without use, it is recommended

that the bag be replaced with a new one, refer to ‘Changing the dust bag’.

dirtdevil.com.au 6

Page 8

dirtdevil.com.au

MAINTENANCE

Changing the dust bag

CAUTION: Switch off the appliance before changing the dust bag.

CAUTION: To avoid damage to the vacuum cleaner, never use the appliance without having inserted

a dust bag. Otherwise, the appliance might be damaged.

21 22 23 24

25 26 27

NOTE: As soon as the dust bag change indicator appears in the window (Fig. 21), the dust bag has to be

changed. In addition, change the dust bag at least every three months and before storing for a long period.

1. Switch off the appliance.

2. Pull the plug out of the plug socket.

3. Use the lid release button to open the dust compartment cover (Fig. 22).

4. Pull the full dust bag out carefully (Fig. 23 – 24).

5. Insert a new dust bag (Fig. 25).

6. Check whether the dust ﬁlter bag is ﬂush with the edges.

7. Unfold the bag after insertion (Fig. 26) so that it can erect itself during vacuuming and ﬁll up optimally.

8. Shut the dust compartment cover (Fig. 27).

Dirt Devil Service Line: AU: 1300 361 505

NZ: 0800 800 900

Page 9

MAINTENANCE

Cleaning / changing the pre-motor ﬁlter

CAUTION: Clean the pre-motor ﬁlter every time you change the dust bag, and at least every 3 months.

Replace the pre-motor ﬁlter at least every 6 months, depending on level of use. As a rule ﬁlters must be replaced as soon as they are discoloured, deformed or damaged.

CAUTION: The ﬁlter is washable, but it may not be cleaned in dishwashers or washing machines.

Also, do not use cleaning agents or brushes with hard bristles. Leave the ﬁlter to dry thoroughly after cleaning it with water (approx. 24 hours at room temperature). Only put it back in place when it is completely dry.

1. Switch off the appliance.

2. Pull the plug out of the plug socket.

3. Take the full dust bag out of the appliance (Fig. 28), refer to: ‘Changing the dust bag’.

4. Pull the ﬁlter up and out of the ﬁlter holder (Fig. 29).

5. Rinse out the ﬁlter thoroughly with running cold or lukewarm water (Fig. 30).

6. Leave the ﬁlter to thoroughly dry (approx. 24 hours at room temperature).

7. Insert the ﬁlter back into the ﬁlter holder (Fig. 31).

8. Put the dust bag back in (Fig. 32), refer to: ‘Changing the dust bag’.

dirtdevil.com.au 8

Page 10

dirtdevil.com.au

MAINTENANCE

Cleaning / changing the post-motor ﬁlter

click!

CAUTION: Clean the post-motor ﬁlter each time you clean the pre-motor ﬁlter. Replace with a new

ﬁlter as soon as it has been discoloured, deformed or is damaged or at least every 6 months, depending on level of use.

CAUTION: The ﬁlter is washable, but it may not be cleaned in dishwashers or washing machines. Also, do not use cleaning agents or brushes with hard bristles. Leave the ﬁlter to dry after cleaning it with water (approx. 24 hours at room temperature). Only put it back in place when it is completely dry.

1. Switch off the appliance.

2. Pull the plug out of the plug socket.

3. Open the post-motor ﬁlter cover as shown (Fig. 33).

4. Take the ﬁlter out of the appliance (Fig. 34).

5. Rinse out the post-motor ﬁlter thoroughly under running cold or lukewarm water (Fig. 35).

6. Then leave the post-motor ﬁlter to dry (approx. 24 hours at room temperature).

7. Put the ﬁlter back into its holder (Fig. 36).

8. Put the post-motor ﬁlter cover into its recesses.

9. Push the cover until it locks into place (Fig. 37).

Dirt Devil Service Line: AU: 1300 361 505

NZ: 0800 800 900

Page 11

FAQ

WARNING: To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance/troubleshooting checks.

Problem Solution

The cleaning results are unsatisfactory in spite of the appliance working correctly

The dust filter bag change indicator appears in the window (Fig. 21).

The vacuum cleaner stops suddenly

The air auxiliary regulator (Fig. 2) is open. Close the air auxiliary regulator (Fig. 2).

Position of the suction power control is not appropriate (Fig. 14). Adjust the position of the suction power control (Fig. 14).

The attached accessory is unsuitable. Change the accessory, ‘Assemble appliance and adjust accessories to surface’.

The collar brush of the combination floor tool is not in a position appropriate to the type of floor (Figures 6 – 7). Adjust the position of the collar brush on the combination floor tool switch using the rocker switch (Figures 6 – 7).

The dust bag is full. Replace the dust bag ‘Changing the dust bag’, page 7.

The filters are dirty. Clean the filters, pages 8-9.

Accessories, telescopic tube or suction hose is blocked. Remove the obstruction. If necessary, use a long wooden stick (e.g. a broomstick) to do this.

The dust bag is full. Change the dust bag, page 7.

The filters are dirty. Clean the filters, pages 8-9.

Accessories, telescopic tube or suction hose is blocked. Remove the obstacle. If necessary, use a long wooden stick (e. g. a broomstick) to do this.

The overheating protection has tripped (possibly due to blocked suction channels, filters, or similar).

1. Switch the appliance off and pull the plug out of the socket.

2. Remove the cause of overheating (e.g. by disassembling telescopic tube and suction hose and removing the obstacle and/or cleaning filters).

3. Wait approx. 1 hour until the appliance has cooled off.

4. After the appliance has cooled off, you may switch it on again.