Diodes PDR5G User Manual
e3
PDR5G
E
E1
b1
A
A2
A2
D
b2
b1
e
L1
L1
E
b1
D
b2
b1
e
D2
L
E2
L1
LEFT PIN
RIGHT PIN
Note: Pins Left & Right must
be electrically connected
at the printed circuit board.
BOTTOMSIDE
HEAT SINK
W
Features
· Glass Passivated Die Construction
· Low Leakage Current
· Lead Free Finish, RoHS Compliant (Note 1)
· "Green" Molding Compound (No Br, Sb)
· Qualified to AEC-Q101 Standards for High Reliability
Mechanical Data
· Case: PowerDI
· Case Material: Molded Plastic, “Green” Molding
Compound. UL Flammability Classification Rating 94V-0
· Moisture Sensitivity: Level 1 per J-STD-020C
· Terminals: Finish – Matte Tin annealed over Copper
leadframe. Solderable per MIL-STD-202, Method 208
· Polarity: See Diagram
· Marking: See Page 3
· Weight: 0.096 grams (approximate)
ä
5
5A GLASS PASSIVATED RECTIFIER
PowerDI
ä
PowerDIä5
A
A2
b1
b2
D
D2
E
e
E1
E2
L
L1
W
Min Max
1.05 1.15
0.33 0.43
0.80 0.99
1.70 1.88
3.90 4.05
3.05 NOM
6.40 6.60
1.84 NOM
5.30 5.45
3.55 NOM
0.75 0.95
0.50 0.65
1.20 1.50
Dim
All Dimensions in mm
5
Maximum Ratings
@ TA = 25°C unless otherwise specified
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Characteristic Symbol
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
RMS Reverse Voltage
Average Rectified Output Current (See also figure 4)
Non-Repetitive Peak Forward Surge Current
8.3ms Single half sine-wave Superimposed on Rated Load
Thermal Characteristics
Thermal Resistance Junction to Soldering Point
Characteristic Symbol Typ Max Unit
Thermal Resistance Junction to Ambient Air (Note 2)
Thermal Resistance Junction to Ambient Air (Note 3)
Thermal Resistance Junction to Ambient Air (Note 4)
Operating Temperature Range
Storage Temperature Range
Notes: 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.
2. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T
3. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T
4. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. T
V
V
V
R(RMS)
I
R
R
R
R
T
RRM
RWM
V
R
I
O
FSM
qJS
qJA
qJA
qJA
T
STG
j
Value
400 V
283 V
5 A
100 A
¾ 1.5 °C/W
75 ¾ °C/W
65 ¾ °C/W
45 ¾ °C/W
¾ -65 to +150 °C
¾ -65 to +150 °C
= 25°C
A
A
= 25°C
A
= 25°C
Unit
DS30552 Rev. 6 - 2 1 of 3 PDR5G
PowerDI is a trademark of Diodes Incorporated. www.diodes.com ã Diodes Incorporated
I , INSTANTANEOUS FORWARD CURRENT (A)
F
V , INSTANTANEOUS FORWARD VOLTAGE (V)
F
Fig. 1 Typical Forward Characteristics
10
1
100
0
0.2
0.4
0.6
0.8
1.0 1.2
100m
1m
10m
T = 25°C
j
T = 85°C
j
T = 150°C
j
T = -65°C
j
0
80
160
240
400
V , INSTANTANEOUS REVERSE VOLTAGE (V)
R
Fig. 2 Typical Reverse Characteristics
I INSTANTANEOUS REVERSE CURRENT (A)
,
R
320
10n
100n
1n
T = +25°C
j
T = +85°C
j
T = +150°C
j
T = +125°C
j
T = -65°C
j
C , TOTAL CAPACITANCE (pF)
T
V , REVERSE VOLTAGE (V)
R
Fig. 3 Typical Total Capacitance vs. Reverse Voltage
0
25
50
75
100
0 5
10
15
20
25
30
f = 1 MHz
0
1.5
3.0
4.5
7.5
6.0
0
25
50
75
100
125
150
175
I , DC FORWARD CURRENT (A)
F
T , AMBIENT TEMPERATURE (°C)
A
Fig. 4 DC Forward Current Derating
Note 2
Note 6
Electrical Characteristics
@ TA = 25°C unless otherwise specified
Characteristic Symbol
Reverse Breakdown Voltage (Note 5)
Forward Voltage
Reverse Leakage Current (Note 5)
Reverse Recovery Time
Notes: 2. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T
3. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T
4. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. T
5. Short duration test pulse used to minimize self-heating effect.
6. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 18.8mm x 14.4mm. Anode pad dimensions 5.6mm x 3.0mm.
V
(BR)R
V
F
I
R
t
rr
Min Typ Max Unit
400 ¾ ¾ V
¾ 0.92 1.15 V
¾
¾
0.02
9
10
250
mA
¾ 3.3 ¾ ms
IR = 10mA
IF = 5A, TS = 25°C
TS = 25°C, VR = 400V
TS = 125°C, VR = 400V
IF = 0.5A, IR = 1.0A,
Irr = 0.25A
= 25°C
A
A
= 25°C
A
Test Condition
= 25°C
DS30552 Rev. 6 - 2 2 of 3 PDR5G
PowerDI is a trademark of Diodes Incorporated. www.diodes.com
Loading...