Diodes AP2602 User Manual
Octave Remote Resistor-programmable Temperature Switches AP2602
Preliminary Datasheet
General Description
The AP2602 are fully integrated, resistor
programmable octave remote temperature switches
with selectable external/internal trigger voltages
setting. The thresholds are set by external resistors
and thermistors with negative temperature
coefficient.
The AP2602 provides 4 open-drain, active low,
over-temperature outputs for each 2 sensors. These
switches operate with a 2.7V to 5.5V single supply.
The AP2602 are available in 16-pin QFN-3X3-16
package.
Features
8 Remote Temperature Switches Set by
•
Thermistor and External Resistors
• 4 Open-drain Active Low Output Stages for
Each 2 Temperature Switches
• Selectable External/Internal Trigger Voltages
Setting
• Built-in Hysteresis Temperature when Using
Internal Setting Trigger Vo ltage
• Guaranteed Output Signal Valid to V
• QFN-3X3-16 Package
=0.8V
CC
Applications
• µP Temperature Monitoring High-speed
Computers
• Temperature Control
• Temperature Alarms
• Fan Control
• Automotives
Figure 1. Package Type of AP2602
QFN-3X3-16
Feb. 2012 Rev. 1. 0 BCD Semiconductor Manufacturing Limited
1
Preliminary Datasheet
Octave Remote Resistor-programmable Temperature Switches AP2602
Pin Configuration
FN Package
(QFN-3X3-16)
Pin 1 M ar k
TMSNS3
TMSNS6
TMSNS2
13141516
TMSNS7
12
11
10
OT12
TMSNS1
TMSNS8
OT78
VTRIG
VCC
GND
Note 1: Recommend connecting the thermal pad to GND for excellent power dissipation.
Figure 2. Pin Configuration of AP2602 (Top View)
1
2
3
SEL
49
OT34
TMSNS4
EP
567 8
OT56
TMSNS5
Pin Description
Pin
Number
1 VTRIG
2 VCC
3 GND
4 SEL
5,7,8,10,
11,13,14,16
6,9,12,15
Pin
Name
TMSNSX
__________
OTXY
Function
Input of external setting trigger voltage
Power-supply input
Ground
Connect SEL to GND to select external trigger voltage, while connecting
SEL to VCC to select internal trigger voltage. Don’t leave the pin floating
Connect an external 1% resistor from TMSNSX to GND to set trigger point
of remote temperature sensorX
Open-Drain, active low, over-temperature output for sensor 1, 2, sensor 3,
4, sensor 5, 6, sensor 7, 8 respectively. The OTXY
results of sensorX and sensorY
__________
outputs are the wire-or
Feb. 2012 Rev. 1. 0 BCD Semiconductor Manufacturing Limited
2
Preliminary Datasheet
Octave Remote Resistor-programmable Temperature Switches AP2602
Functional Block Diagram
VTRIG
SEL
VCC
4
1
2
TMSNS
TMSNS2
TMSNS8
11
1
13
14
16
5
7
8
&
10
VREF
VREF
CMP
CMP with
Hysteresis
CMP
CMP with
Hysteresis
Deglitch Logic
Deglitch Logic
12
15
OT12
6
&
9
OT78
Figure 3. Functional Block Diagram of AP2602
3
GND
Feb. 2012 Rev. 1. 0 BCD Semiconductor Manufacturing Limited
3
Preliminary Datasheet
Octave Remote Resistor-programmable Temperature Switches AP2602
Ordering Information
AP2602 -
Circuit Type G1: Green
Package
QFN-3X3-16
Package
FN: QFN-3X3-16
Temperature
Range
-40 to 125°C
Part Number Marking ID
AP2602FNTR-G1 B2E Tape & Reel
TR: Tape & Reel
Packing
Type
BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant
and green.
Absolute Maximum Ratings (Note 2)
Parameter Symbol Value Unit
Supply Voltage VCC -0.3 to 6 V
OTXY Voltage
TMSNSX, VTRIG Voltage
SEL Voltage V
Output Current (All Pins) 20 mA
Input Current (All Pins) 20 mA
Operating Junction Temperature TJ 150
Storage Temperature Range T
Lead T em perature
(Soldering, 10 seconds)
Thermal Resistance
VOT -0.3 to 6 V
V
TMSNSX,
V
TRIG
-0.3 to 6 V
SEL
-65 to 150
STG
260
T
LEAD
θ
JA
QFN-3X3-16 68
-0.3 to V
+0.3 V
CC
°C
°C
°C
°C/W
ESD (Machine Model)
ESD (Human Body Model)
Note 2: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. These are stress ratings only, and functional operation of the device at these or any other conditions
beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute
Maximum Ratings” for extended periods may affect device reliability.
Feb. 2012 Rev. 1. 0 BCD Semiconductor Manufacturing Limited
4
200 V
2000 V
Loading...