Dinex IESSB10 User Manual

JOB _____________

TRAY MAKEUP SLAT BELT MOTORIZED CONVEYORS

Item Numbers

Slat Belt Motorized Conveyors

q DXIESSB8

q DXIESSB10

q DXIESSB12

q DXIESSB14

q DXIESSB16

q DXIESSB18

q DXIESSB20

Shown with optional electric
raceway and outlets.

ITEM # _____________

Application

The straight-line Slat Belt motorized
conveyor is designed for tray make-up
operations. The Slat Belt conveyor will
help streamline tray assembly for any
healthcare or catering operation. All units
can be equipped with raceways and
breaker panels for online support
equipment connections. Mobile or
stationary, these units are designed for
easy cleaning and long life. Since these
units are built to customer specification
some units may not be available in
mobile configuration. Please consult
factory.

Construction

Drive housing is 18-gauge stainless
steel. 2” x 2” x .1875” stainless steel all
welded angle and channel framework.
Removable panels provided for easy
access. Stainless steel shelf on outside
end of drive section to hold soaplube
container.

Conveyor is driven by a totally enclosed
fan cooled D.C. permanent magnet
motor through worm gear speed reducer,
sprockets, and roller chain. Motor
controlled with SCR power transmission
group. Main control panel has speed
control station with stop-start controls

includes dynamic braking, and is NEMA
4 watertight. Shafting is solid stainless
steel with stainless steel sprockets.
Bearings are self-aligning ball bearings
sealed for life.

Belt is Lo-Friction Lexan plastic with
tapered slats carried by stainless steel
roller chain. Slats are snap attached to
chain and do not require special tools
for removal. Belt speed is electronically
adjustable in speed range from
approximately 0 to 40 FPM.

Conveyor slider pan belt terminates at
drive end to provide flat top space for
one tray. Die-formed crimp edge has
straight turndown on long sides and is
straight down on ends. Belt will terminate
at drive end to provide flat top space
for one tray. Supports are 1.625” O.D.
No.16-gauge stainless steel tubing
“H” frames on 6’ to 7’ centers.
Interconnecting crossrails are required.

The intermediate section is 1.5” x 1.5”,
No. 12-gauge stainless steel angle
framing with full length replaceable
synthetic guide rails for belt return.

The tail section consists of a stainless
steel framework which houses tail roller
and bracket guides. Stainless steel
panels will conceal frame where exposed.

The optional wash system is located
within the drive housing and consists
of all welded stainless steel wash tank
with removable scrap collection basket.
Tank is fitted with spray manifolds
pre-piped to detergent injection
system with solenoid valve to control
flow of wash solution onto belt. Positive
displacement type detergent pump is
electrically operated. Stainless steel drip
collection pans are located beneath the
belt return track for the entire length of
the conveyor. 140°F hot water is
recommended for the wash system.

Warranty

One year parts and labor.

Building 2, Suite 106
628 Hebron Avenue
Glastonbury, CT 06033

800.523.9752 Fax: [phone]
www.dinex.com

049-REV 10/09

TRAY MAKEUP SLAT BELT MOTORIZED CONVEYORS

Application

Panel box is watertight NEMA 3R
construction located on conveyor in
totally accessible area. Integrally
connected to panel box is an all
stainless steel electric receptacle
housing full length of conveyor. The
optional electric raceway is of watertight
construction. All receptacles required
for support equipment have watertight
spring loaded covers or threaded
removable watertight ring covers with
rust resistant ball and chain. All
receptacles are wired on individual
circuits to panel box and matched to
electrical support equipment.

For the optional wash system provide a
.5” 140°F hot water stub out of floor at
drive housing for connecting to valve in
the drive section (if mobile, a quick
disconnect is required). Provide hub
drain or floor drain under drive housing.
A drain is required under the tail section
if the conveyor is over 16’ long. Electrical
service at location is required (stub if
stationary, grounded receptacle if
mobile). Conveyor can be furnished
in any voltage that is available in the
Continental United States.

Note: Engineering data chart must be
completed accurately for proper
selection of receptacles and panel box.

21” (53cm)

10” (25cm)

Drive Elevation

Standard features

• Electrical raceway

• Variable speed

• SBC 10” slat with stainless steel

carrier chain

• Stainless steel replaceable wear

strips

• Pan limit switch

• Stationary

• Dry operation with manual

cleaning

• Replaceable belt return rails

• Removable scrap basket

• All welded heavy-duty frame

36” (91cm)

6” (15cm)

Options

• Electric raceway

• Receptacles

• Casters

• Field joints

• Cord and plug

• Wash systems

Items and Dimensions

ITEM NUMBER MODEL NUMBER SIZE SHIP WEIGHT

DXIESSB8 IESSB8 8 ft. (2.4 meter) section 600 lb. (272kg)

DXIESSB10 IESSB10 10 ft. (3.05 meter) section 750 lb. (340kg)

DXIESSB12 IESSB12 12 ft. (3.6 meter) section 900 lb. (408kg)

DXIESSB14 IESSB14 14 ft. (4.3 meter) section 960 lb. (435kg)

DXIESSB16 IESSB16 16 ft. (4.9 meter) section 1,020 lb. (462kg)

DXIESSB18 IESSB18 18 ft. (5.5 meter) section 1,080 lb. (489kg)

DXIESSB20 IESSB20 20 ft. (6.1 meter) section 1,140 lb. (517kg)

Please confirm that you have the most current specification sheet by visiting www.dinex.com.

Dinex® reserves the right to change specifications and product design without notice.
Such revisions do not entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased equipment.

Printed in USA

Building 2, Suite 106
628 Hebron Avenue
Glastonbury, CT 06033

800.523.9752 Fax: [phone]
www.dinex.com

049-REV 10/09