Dinex IESB10 User Manual

TRAY MAKEUP CONVEYORS

Shown with optional electric
raceway and outlets.

JOB _____________

Item Numbers

Band Belt Conveyors

q DXIESB8

q DXIESB10

q DXIESB12

q DXIESB14

q DXIESB16

q DXIESB18

q DXIESB20

ITEM # _____________

Application

The straight-line Band Belt motorized
conveyor is designed for tray make-up
operations. The Band Belt conveyor will
help streamline tray assembly for any
healthcare or catering operation. All units
can be equipped with raceways and
breaker panels for on-line support
equipment connections. Mobile or
stationary, these units are designed for
easy cleaning and long life. Since these
units are built to customer specification
some units may not be available in
mobile configuration. Please consult
factory.

Construction

Drive housing is 18-gauge stainless
steel. 2” x 2” x 3/16” stainless steel all
welded angle and channel framework.
Removable panels provided for easy
access.

Drive is totally enclosed fan cooled D.C.
permanent magnet motor through worm
gear speed reducer, sprockets, and roller
chain. Automatic belt tensioning device
is provided. Rollers are crowned to
assure proper tracking. Conveyor is
furnished with side belt guides to also
assist in belt tracking. Motor controlled
with SCR power transmission group.

SCR main control panel has speed
control station with stop-start controls.
SCR system includes dynamic braking.
All controls are NEMA 4 watertight.
Shafting is solid stainless steel with
stainless steel sprockets. Bearings are
self-aligning ball bearings sealed for life.

Dual 1/2” diameter urethane belts are
FDA approved.

Belt speed is electronically adjustable in
speeds ranging from approximately 0 to
40 FPM.

Die-formed crimp edge has straight
turndown on long sides and is straight
down on ends. Belt terminates at drive
end to provide flat top space for one
tray. Supports are 1.625”(4cm) O.D.
No.16-gauge stainless steel tubing
“H” frames on 6’ to 7’ centers.
Interconnecting crossrails are required.

The intermediate section is 1.5” x

1.5” x No.12-gauge stainless steel
angle frame. 1.875” O.D. PVC bearing
supported stainless steel shaft mounted
idler rollers on 48”(122cm) centers.
Exposed sides are fitted with removable
stainless steel panels.

The tail section consists of a stainless
steel framework which houses tail roller
and bracket guides. Stainless steel
panels conceal frame where exposed.

Manual cleaning system head section
fitted with stainless steel slide out
crumb collector pan. Conveyor will
stop as tray reaches check point and
will automatically restart when tray
is removed.

Warranty

One year parts and labor.

Building 2, Suite 106
628 Hebron Avenue
Glastonbury, CT 06033

800.523.9752 Fax: [phone]
www.dinex.com

053-REV 10/09

TRAY MAKEUP CONVEYORS

Panel box is watertight NEMA 3R
construction located on conveyor in
totally accessible area. Integrally
connected to panel box is an all
stainless steel electric receptacle
housing full length of conveyor. The
optional electric raceway is of watertight
construction. All receptacles required
for support equipment have watertight
spring loaded covers or threaded
removable watertight ring covers with
rust resistant ball and chain. All
receptacles are wired on individual
circuits to panel box and matched
to electrical support equipment.

Electrical service at location is required
(stub if stationary, grounded receptacle
if mobile). Conveyor can be furnished in
any voltage that is available in the
Continental United States.

1.625”(4cm) O.D.

stainless steel

and crossrails

14-gauge

stainless
steel top

Stainless steel

apron at sides

16-gauge

tubing legs

Determined by tray size

1/2” diameter hyphen solid
polyurethane belt with
continuous polyester core

10”

(25cm)

1.875”(5cm)
O.D. P.V.C.
idler rollers

35”

(89cm)

10”

(25cm)

Note: Engineering data chart must
be completed accurately for proper
selection of receptacles and panel box.

Items and Dimensions

ITEM NUMBER MODEL NUMBER SIZE SHIP WEIGHT

DXIESB8 IESB8 8 ft. (2.4 meter) section 680 lb. (272kg)

DXIESB10 IESB10 10 ft. (3.05 meter) section 740 lb. (340kg)

DXIESB12 IESB12 12 ft. (3.6 meter) section 800 lb. (408kg)

DXIESB14 IESB14 14 ft. (4.3 meter) section 860 lb. (435kg)

DXIESB16 IESB16 16 ft. (4.9 meter) section 920 lb. (462kg)

DXIESB18 IESB18 18 ft. (5.5 meter) section 980 lb. (489kg)

Stainless steel

adjustable bullet

shaped feet

Standard Features

• Variable speed

• Two 1/2” diameter round belts and

FDA approved

• Slider pan has “Air Glide” ride

• Pan limit switch

• Stationary

• Dry operation

• Removable crumb-collector pan

• All welded heavy duty frame

Options

• Electric raceway

• Receptacles

• Casters

• Field joint

• Cord and plug

DXIESB20 IESB20 20 ft. (6.1 meter) section 1,040 lb. (517kg)

Please confirm that you have the most current specification sheet by visiting www.dinex.com.

Dinex® reserves the right to change specifications and product design without notice.
Such revisions do not entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased equipment.

Printed in USA

Building 2, Suite 106
628 Hebron Avenue
Glastonbury, CT 06033

800.523.9752 Fax: [phone]
www.dinex.com

053-REV 10/09