Dinex IDTIC Service Manual

Cantilev er
Tray & Rack Dispensers

Models IDTIC/ IDT2C/ & IDRC/

DINEX INTERNATIONAL,INC. • 628-2 HEBRON AVENUE,GLASTONBURY CT 06033 • WWW.DINEX.COM

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Spring Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Carrier Platform Field Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Dinex® Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

For Service Information,call 1-888-673-4639

Please provide following information:

• Model number

• Serial number

• Part Description and number as shown in parts list.

Manual No. TRD-C-2 Rev-07/05

Service Manual

Printed in the USA

For Equipment with Serial Number 040001N

SPRING CALIBRATION

To remove back panel

1.Remove two screws (item 1) from bottom of panel.
(Figure 1)

2.Insert ball point pen or similar object into hole (item 2),
and lift panel up,out,and down.(Figure 2).

Page 2

Introduction:

Installation:

Congratulations:You have just purchased one of the finest
pieces of equipment on the market today.Before installing
or operating our new Dinex® Products equipment you
should read through this material.This manual should be
retained for further reference as it contains installation and
operating instructions,service tips,part list and warranty
information.Should you have any questions concerning
the Equipment,please call the Dinex Hotline at 1-888-673­4639 (Monday through Friday from 8 am to 5 pm,Eastern
Standard Time).

IMPORTANT: For your safety,read and follow all cautions,
information and warnings

FREIGHT DAMAGE CLAIMS

Your Dinex® Products equipment was carefully inspected
and packed before leaving our factory. The transpor tation
company assumes full responsibility for safe delivery of
this equipment.Dinex® Products cannot assume responsi­bility for damage or loss incurred in transit.Visible damage
or loss should be noted on freight bill and signed by
person making delivery.

A freight claim should be filed immediately with the trans­portation company.If damage is unnoticed or concealed
until equipment is unpacked,notify the transpor tation
company immediately and tell them you want to file a
concealed damage claim.This must be done within fifteen
(15) days after delivery was made.Be sure to retain all

packing material and cartons.

WARNING:Installation of this equipment should be
performed only by persons qualified or licensed to install
electrical equipment.

• Adjustments and service work should be performed
only by a qualified service technician.S er vice is available
through Authorized Dinex® Products Parts & Service
Distributors throughout the United States.For a
complete listing of these consult your distributor listing
or write Dinex® Products for the name of the nearest
distributor.

• This equipment in intended for commercial use only.
Not for household use.

• Use of other than genuine Dinex® Products replace­ments parts or service work performed by other than
authorized Dinex® Products service agents will void the
warranty.

• Do not use any corrosive cleaners.Use only cleaners
approved for stainless steel.

!

!

Figure 1

2

1

1

3

2

Back
Panel

Figure 2