Dinex 611120, 611220, 611208, 611240 Operating And Maintenance Manual
DINEX INTERNATIONAL, INC. • 628-2 HEBRON AVENUE, GLASTONBURY CT 06033 • WWW.DINEX.COM
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dinex® Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SMART•THERM™ MODES: Induction Base Heating or change to
Cook-Top Mode for use with induction cooking pans.
For Service Information, call 1-888-673-4639
Please provide following information:
• Model number
• Serial number
Manual No. IH-ST-2 Rev-05/06
Sm a r t • Th e r m
™
O p e r ating & Ma i n te n a n c e Ma n u a l
Model: 611120 (120V), 611220 (208V/240V)
611208 (208V), 611240 (240V)
Page 2
Introduction
You have purchased the new Dinex® Smart•Therm™
Induction Charger. Please read this manual for helpful
guidelines on how to use your Equipment. Should you
have any questions concerning the Equipment, please call
the Dinex® Service at 1-888-673-4639.
IMPORTANT: For your safety,read and follow all cautions,
information and warnings.
FREIGHT DAMAGE CLAIMS
Your Smart•Therm Induction Charger was carefully
inspected and packed before leaving our factory.The
transportation company assumes full responsibility for
safe delivery of this equipment. Dinex® cannot assume
responsibilities for damage or loss incurred in transit.
Visible damage or loss should be noted on the freight bill
and signed by the person making the delivery.
A freight claim should be filed immediately with the transportation company. If damage is unnoticed or concealed
until equipment is unpacked, notify the transportation
company immediately and tell them you want to file a
concealed damage claim. This must be done within fifteen
(15) days after delivery was made. Be sure to retain all
packing material and cartons.
WARNING: Use of this symbol identifies a potentially
hazardous situation which, if not avoided,may result in
damage to the machine or injury to the operator.
CAUTION: If the product is used without observing the
information given under this symbol, minor personal
injury, or damage to equipment may result.
WARNING: Installation of this equipment should be
performed only by persons qualified or licensed to install
electrical equipment.
• Adjustments and service work should be performed only
by qualified service technicians.
• This equipment is intended for commercial use only.
Not for household use.
• Use of other than genuine Dinex® replacement parts or
service work performed by other than authorized Dinex®
service agents will void the warranty.
• Do not use any corrosive cleaners. Use only mild
detergents.
APPLICATION & USE
The Eq u i p m e nt is for co m m e r cial use in the food serv i ce
i n d u s t r y. It provides maximum induction heating co m p at i b l e
Di n ex® bases. Use in Sm a r t • T h e r m ™ m ode with Di n e x ®
Sm a r t • T h e r m™ base only. Modes 611120 & 611220 can also
be used in coo k - top mode after re m oval of base locato r.
SAFETY
The instructions contained in this manual provide important guidelines for the Equipment user regarding a correct
and safe installation. Particular attention should be paid to
the warnings given in various parts of this manual. Do not
attempt to repair this equipment. Repairs are to be performed by authorized personnel only.
• Do not use the machine if glass is broken or if anything
melts onto it.
•
Always use an i n d u c tion co m p a t i b l e pan 8 inches or more
in diameter on the cook-top surface. (cook-top mode)
• Never use the machine as a work surf a ce or cutting bo a rd.
•
Do not attempt to heat aluminum fo i l .
•
Never attempt to cook food dire ct l y on the glass surf a ce.
• Always have the base loca t or in place when heating induct i o n
b a s e s .
IMPORTANT: Do not put Smart•Therm™base in microwave
oven.
INFO: Please note that this appliance is for commercial
use only and must be used exclusively for the purposes
prescribed.
IMPORTANT: The following instructions reduces the risk
of fire, electrical shock or injury.
SET UP
1. Carefully remove any packing material from the charger
and check loose packing material for small parts or
accessories. Inspect charger for concealed damage
before putting packing material aside. Keep packing
until you are confident with equipment application.
2. The Smart•Therm™ charger (mdl 611120) is equipped
with a three-prong electrical plug. The Smart•Therm™
chargers (mdls 611220, 611208, 611240) are equipped
with a locking plug. These plugs are part of a system
that will protect you from serious injury if something
goes wrong with the electrical wiring in the charger. Be
sure the plug is plugged into a matching soc k et that is
p r o p e r ly gro u n d e d.
WARNING: DO NOT cut or break off the large third prong
in this plug, or change the plug or power cord in any way.
Doing so will create a safety hazard and also void the
warranty.
3. MAKE SURE THAT INCOMING VOLTAGE MATCHES
CHARGER REQUIREMENTS. A product identification
l a bel on the bo t t om of the charger specifies the ope rating vo l t a g e, wat t a g e, c u rre n t, f re q u e n cy, and phase of
c h a r g e r.
Plugging or wiring the charger into less vo l tage than the charger is rated may significa nt l y
d e c r ease the pe r fo rm a n c e or seve rely damage elect r onic co m po n e n t s .
!
!
!
!
!
!
!
!
Installation
2. The Sm a r t • T h e rm™ Ch a r ger is turned on by pressing the
g reen “ P OW E R ”b u t t on on the left fro n t of the membra n e
panel. A green LED will illuminate indicating that the
Smart•Therm™ Charger is turned on and ready for use.
3 .
Be sure base locator is placed on the Sm a r t • T h e r m ™
Ch a rger pro p e r l y.
4 . Pl a c e a Di n e x® Sm a rt • Th e r m™ base on the Sm a rt • Th e r m ™
Ch a rg e r . The charger will beep once as it re cog n i z es the base.
5. Red LED(s) will illuminate indicating that the base is
c h a r g i n g . Do Not Remove the base while the red LED(s)
a re in prog re s s i o n . As the base charg e s, the red LED(s)
will light prog r e s s i vely to the ri g h t until all 10 are lit. If the
base is re m oved be f o r e all 10 are lit,it will not be fully
c h a r ged resulting in a lower delive r y te m pe r at u re.
INFO: You will hear three loud “BEEPS”if you remove the
base before it is fully charged.
6. If no red LED’s illuminate, re m o ve and re position the base.
7. After all 10 LED’s light, they will all flash and the charger
will beep indicating that base is at the full temperature.
Charge time for a base will be approximately 13 seconds
for 611240, 15 seconds for 611208, 17 seconds for
611220 @ 240V, 20 seconds @ 208V,or 30 seconds
for 611120 (120V), depending on the residual energy in
the base. Voltages lower than those listed will increase
changing time.
INFO: Fluctuation in voltage may affect cycle heating time.
8. When the heating cycle is complete, the 10 LED’s will
flash and an audible signal will indicate that the base
has completed its cycle.
9. I m m e d i a tely place another base on the Sm a r t • Th e r m ™
Ch a r ger making sure that the red LED(s) illuminate. If the
base is alre a dy partially charged the cycle time will be
re d u c ed acco r d i n g l y . The number of LED’s will indicate the
i n te r nal level of late nt heat or charge re m a i n i n g. Fo r
ex a m p l e, if 4 LED’s are lit,the base will re q u i re only 6 more
l i g h ts to co m p l e t e the cycle time for a full charg e.
10. If the charger sees no activity for an extended period of
time, it will beep 2 times and go into “Sleep” mode to
conserve power. This will be indicated by the red LED’s
scrolling across the display. Press any button to restart
normal operation.
11. The Smart•Therm™ Charger has an auto-shutoff fea-
ture that will turn off the machine after it has been idle
for a period of time. The charger can also be turned off
manually by depressing the “power” button.
INFO: The cooling fan will continue to run and will turn off
approximately 20 seconds after the power is turned off.
Smart•Therm™ chargers have an auto-reset feature that is
activated when the unit is turned off. Upon turning the unit
off, the fan will cycle on, all lights will flash,and it will then
turn off.
COOKING MODE (611120 & 611220 ONLY!)
WARNING: Do not heat Smart•Bases in cooktop mode.
Doing so will void warranty. Always use the Base Locator
when heating Smart•Bases.
The Smart•Therm™ Charger will power up by default in
the Smart•Therm™ mode. If your charger is equiped with
the cooktop feature, you can also use the charger as a
Page 3
4. Do not place foreign objects on the charger,or between
the Dinex® base and locator. Foreign objects may overheat and cause damage to the charger and/or base.
5. Do not use any Smart•Therm™ Charger that has a damaged cord or plug. Consult the warranty and follow
instructions for service.
6. Do not let the charger cord touch hot surfaces.
7. The center of the charger top may get hot to the touch
after hours of continuous use. Use caution when loading and unloading bases.
8. A dedicated electrical circuit is recommended for
EACH Smart•Therm™ Charger.
IMPORTANT: Every installation site has different electrical
wiring requirement. Because many different local codes
exist, it is the owner and installer’s responsibility to comply
with all federal, state and local codes. Dinex® is not responsible for any consequential damages, either expressed or
implied, as a result of failure to comply with installation
requirements.
WA R N I N G : Please do not attempt to open the charger or pe rform
s e rv i ce of any ki n d. This prod u ct can only be serv i ced by a Di n e x ®
Au t h o ri z ed Se rv i ce Agent or designated Di n ex® pe r s o n n e l . Co n t a c t
Di n ex® at 1-888-673-4639 for serv i ce info r m a t i o n .
WARNING: Any installation not matching the requirements discussed in this manual will automatically void
the product’s warranty.
INSTALLATION
1. The Smart•Therm™ Charger can be installed on top of a
flat, level countertop or shelving, being careful to maintain at least two inches of clearance on all sides of the
charger for cooling. Do not place over paper or
loose material. That may inhibit air flow.
Dinex® Induction Stand
(Assessory product)
ICSTANDM (Mobile with casters)
ICSTAND (Not mobile)
2. The charger must be plugged into a grounded 120V,
208V or 240V (depending on the model purchased), single-phase receptacle. Check rating base on the charger
to verify correct voltage.
IMPORTANT: Each charger should be connected to its own
dedicated circuit. They should not be connected to circuits
sharing compressors or other heavy current draw devices.
(i.e. plate heaters, steam tables,etc.)
3. Do not move the Smart•Therm™ Charger when it is
electrically connected.
SMART•THERM™ MODE
WARNING: Do not heat Smart•Bases in cooktop mode.
Doing so will void warranty. Always use the Base Locator
when heating Smart•Bases.
1. Make sure that your Smart•Therm™ Charger is plugged
into an energized circuit as described in the previous
section. This should be a dedicated circuit, not shared
with any devices utilizing motors, compressors, or components requiring a heavy current draw.
Operation Instructions
!
!
!
!
!
!
!
!
!
Loading...