Dimplex HFPI9280 User Manual

PARTS AND SERVICE MANUAL

FOR THE 23” INSERT FIREPLACE

MODEL NUMBER:

HFPI9280 DFPI2311

TABLE OF CONTENTS

OPERATION PAGE 1

PARTS DRAWING PAGE 5

PARTS LIST PAGE 6

WIRING SCHEMATICS PAGE 7

LIGHT BULB REPLACEMENT PAGE 8

MANUAL CONTROL ON/OFF SWITCH REPLACEMENT PAGE 9

FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 10

POWER CORD REPLACEMENT PAGE 12

HEATER ASSEMBLY REPLACEMENT PAGE 13

REMOTE CONTROL CIRCUIT BOARD REPLACEMENT PAGE 14

HEATER DISABELER SWITCH REPLACEMENT PAGE 15

HFPI9280, DFI2311

OPERATION

Initializing The Remote Control

1. Turn on the electrical power at the circuit breaker.

2. Slide open the battery cover on the back of the remote transmitter.

3. Install three AAA batteries into the remote control. Replace the battery cover.

Note:

The LCD display will flash when new batteries are inserted.

4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press any button on the remote control. The remote is transferring the code to the receiver built into the fireplace.

5. Set the clock by depressing the button marked clock on the transmitter for five seconds. The hour display will flash.

6. Use the up and down buttons to set the hour.

7. Press the clock button again and the minute display will flash.

8. Use the up and down buttons to set the minute.

9. Press the clock button again and the 0F or 0C display will flash.

10. Use the up and down buttons to select the remote to display temperature in 0F or 0C

11. Press the clock button again. The remote control is now ready for operation.

Remote Control Operation

Warning

It takes some time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for correct operation.

Flame Mode Note

When flame mode is activated the flame will turn on only.

Note

When the flame button is pressed the display screen will display the flame status on or off.

To turn the flame on:

1. Press the FLAME button once.

2. The display screen will read OFF.

3. Press the FLAME button turn the flame on.

To turn the flame off:

1. Press the FLAME button once.

2. The display screen will read ON.

3. Press the FLAME button to turn the flame OFF.

HFPI9280, DFI2311

Auto Mode Note

When auto mode is activated the flame and heat will turn on. The heater will turn on and off to keep the room temperature the same as the remote controls set temperature.

1. Use the UP and DOWN buttons to set the desired target temperature.

2. Press the AUTO/OFF button once to activate the auto mode. In auto mode the remote transmitter will automatically turn on the flame and heater when the room temperature is below the target temperature and turn off the heater ONLY when the room temperature is above the target temperature.

3. Press the AUTO/OFF button to turn off the heater and flame (if it is already on) and exit the auto mode.

Sleep Mode

1. You can set the timer to the length of time you want the heater to operate (1 to 120 minutes).

2. Press the TIMER button once. The timer display will blink ---

3. Press the UP and DOWN buttons to adjust the timer display in minutes.

4. Press the TIMER button once to set the timer.

5. The timer setting can be reset by pressing the TIMER button and using the DOWN button until the timer display reads ----, press the TIMER button once to set the timer.

6. Press the AUTO/OFF button to turn on the heater.

7. The heater will turn off at the end of the timer setting.

Child Proof Function

1. Remove the battery cover on the back of the remote control.

2. Slide the small blue switch down to activate the child proof function.

3. Child Proof will appear on the display screen and all function on the remote will be locked.

4. To enable normal remote control operation when the child proof function is activated, press the up and down buttons in the following sequence, UP-DOWN-DOWN-UP-DOWN the remote functions will now operate normally. The remote will return to the child proof function if buttons are not pressed after two minutes.

5. To disable the child proof function remove the battery cover on the back of the remote and slide the small blue switch up.

Batteries

1. The remote control uses 3 AAA size batteries. Replace these batteries at least every 6 months or when the low battery appears on the remote display screen.

2. When batteries are removed wait at least 1 minute before replacing with new batteries.

HFPI9280, DFI2311

Code selection

If the current remote control is interfering with the operation of other remote control devices (TV, VCR, garage doors etc.) The code can be changed on the remote.

To change code:

1. Remove the battery cover on the back of the remote control.

2. Slide the four small switches to any configuration other than the factory set code.

3. Remove the batteries, wait for one minute.

4. Install the batteries.

5. Install the battery cover onto the remote.

6. Reinitialize the remote to match the new code to the masonry insert.

HFPI9280, DFPI2311

OPERATION

Masonry Insert Manual Control

1. The masonry insert has a manual power ON/OFF switch located in the upper corner of the unit.

2. To operate press the switch once, to turn the unit on. A red light will illuminate to indicate the power is on. Press the switch again to turn the unit off. Note When the manual power switch is used the heater will run. The manual ON/OFF switch is to be used only when the remote transmitter is OFF.

+ 11 hidden pages