These instructions should be read carefully and
retained for future use. Note also the information
presented on the appliance.
ISSUE: 1 Series: A
IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR
DAMAGE AND MAY INVALIDATE YOUR GUARANTEE
IMPORTANT SAFETY ADVICE
When using electrical heaters, basic precautions should always be followed to reduce the risk
of re, electrical shock, and injury to persons, including the following:
IMPORTANT – The wall bracket supplied with the heater must be used.
IMPORTANT – All packaging should be disposed of in an appropriate manner.
OVERHEATING WARNING
WARNING - In order to avoid overheating, do not cover or obstruct the heater. Do not place material
or garments on the heater, or obstruct the air circulation around the heater, for instance by curtains
or furniture, as this could cause overheating and a re risk. NEVER cover or obstruct in any way the
heat outlet slots at the top of the heater or the air inlet slots in the base of the heater.
WARNING -
THE SURFACES ON THIS HEATER CAN BE HOT. The heater carries a warning
‘DO NOT COVER’ to alert the user to the risk of re that exists if the heater is accidentally
covered.
CAUTION - Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
For your safety this heater is tted with a thermal cut-out. In the event that the product
overheats for some reason, the cut-out prevents excessive temperatures on the product by
cutting the power to the heater. Once the heater has cooled down, it will reset automatically,
it will continue to cycle on and o automatically until the reason for overheating is removed.
The display screen may ash red to indicate the product has overheated. To reset the display,
remove the obstruction and hold Enter for 10 seconds.
SUITABLE APPLICATIONS
WARNING - This heater is suitable for normal domestic household purposes and should not
be used in any other type of environment. This product should only be used in the country
where it was purchased from by a recognised commercial retailer. Do not use outdoors.
SERVICING AND REPAIRS
WARNING - Servicing and product repairs should only be undertaken by the manufacturers
approved service agent or a similarly trained or qualied person, using only exact manufacturer
approved spare parts.
PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with the
convection eect of electric heaters can cause signicant soot deposits to build up on the
surface directly above and to the sides of the heater. This is not a fault of the heater. Extensive
burning of candles or smoking in the operating environment of this product can produce heavy
discolouration within a few months of use.
OPERATING WARNINGS
IMPORTANT: Remember to observe all safety warnings and precautions when operating the
heater on the automatic or timer modes, either attended or unattended since a re risk exists
when the heater is accidentally covered or displaced.
CAUTION: Do not use if the heater’s mains power lead is damaged. If the supply cord is
damaged it must be replaced by the installer or an approved Dimplex service partner.
2
ELECTRICAL INSTALLATION
WARNING - The electrical installation of this heater must be carried out by a suitably qualied
or trained electrician, and be in strict accordance with the current wiring Regulations BS
7671. The supply must be connected via a switched fused spur with a fuse rated suitably
for the appliances ex. Failure to follow these instructions will mean that the manufacturer’s
instructions have not been adhered to. THERE ARE NO EXCEPTIONS.
WARNING - Minimum clearances and IP zone requirements must be adhered to in accordance
with the current wiring regulations.
The wires in this mains lead are coloured in accordance with the following code:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
• This heater must be earthed
• Not suitable for connection via a plug top
• Do not locate the heater immediately below a xed electrical point i.e. socket outlet.
The heater is tted with a length of exible cable type H05VV-F size 3 x 1.0mm² for 500W to
2kW models for connection to the xed wiring of the premises through a suitable connection
box positioned adjacent to the heater. A means for disconnection must be incorporated in the
xed wiring of the premises in accordance with the current wiring regulations. The supply circuit
to the heater must incorporate a double pole isolating switch having a contact separation of at
least 3mm. Products that are supplied without a plug are for installation into the xed wiring of
the property, via a suitable double pole switched fused spur with a fuse rated suitably for the
appliances ex. Typical fuse ratings for 230V equipment - Up to 700W = 3A, over 700W = 13A.
In installation the supply cord may be cut to the appropriate length for the electrical connection
point. Excess cable should not be inserted and stored behind the heater.
WARNING: This heater must not be connected to the electricity supply via an external switching
device (such as a timer) or a circuit that is regularly switched on and o by the utility supplier.
Failure to follow this warning could result in the heater’s thermal cut-o being inadvertently
reset and could create a re hazard. Cables/exes that are supplied pre-tted to the product
must NOT be extended.
CHILD SAFETY
WARNING - This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of appliance by a person responsible for their safety.
This appliance can be used by children from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/o the appliance provided
that it has been placed or installed in its intended normal operating position and they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years and less than 8 years shall not regulate and
clean the appliance or perform user maintenance. This product contains a replaceable battery.
WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN.
WARNING - Packaging should be disposed o responsibly as the EPS could be a potential
chocking hazard for children
3
Energy Related Product Directive
This product complies with Lot20 of the Energy Eciency Directive (2015/1188).
Type of heat output/ room temperature control
With electronic room temperature controlYes
Electronic room temperature control plus week timerYes
ManufacturerGlen Dimplex Heating & Ventilation (GDC Group Ltd.)
5
General Information
Please read the instructions closely before rst using the product, there is also a quick-start
guide on page 8 if you need a reminder of how to use the basic functions in the future.
The heater is designed for wall mounting using the wall bracket supplied. It should only be
operated when in the upright position as shown - see Fig.3 and Fig.4. All models are splash
proof to IP24. Before connecting the heater check that the supply voltage is the same as that
stated on the heater.
Wall Mounting Instructions
IMPORTANT - The wall bracket
supplied with the heater must
be used and the heater must
be installed in the correct
orientation. The xings should
be used to secure the bracket to
the particular wall on which the
heater will be installed. The heater
should be positioned observing
the minimum clearances stated
around the heater - see Fig. 2,
Fig. 3 and Fig. 4.
‘B’
Minimum
mounting
clearance
MODELABCDE
GFP050E128mm263mm450mm430mm108mm
GFP075E298mm263mm620mm430mm108mm
GFP100E298mm263mm620mm430mm108mm
GFP150E368mm263mm690mm430mm108mm
GFP200E538mm263mm860mm430mm108mm
Fig. 2
‘A’
310
255
Minimum mounting clearance
6
To mount the heater to the wall:
1. Remove wall mounting bracket from the back of the heater by depressing the spring latch
at the side of each bracket - see Fig.2.
2. Fix the wall bracket securely to the wall through the four screw holes. Ensure only screw
ttings provided are used for the particular wall type.
3. Present the heater to the wall bracket and engage bottom slots in the back with bracket hooks.
4. Press heater into locked position and ensure the clips on the top are engaged.
WARNING:
This product is heavy and care
should be taken in installation
150mm
‘D’
(min)
Minimum mounting clearance
‘C’
150mm
(min)
Fig. 3
150
(min)
mm
Shelf / Obstruction
150mm
(min)
Minimum front
clearance
300mm
150mm
(min)
Fig. 4
‘E’
*Please note correct product
orientation is with controller
facing top right side only
7
Quick Start Guide
This guide is for quick reference only.
Please refer to the operating section on Page 10 for further information.
How Does the Heater Control Work?
The controller allows you to choose when you want heat and at what temperature.
When using a timer mode (see below), Comfort On will display on the home screen to tell you
when the heater is maintaining the temperature displayed. Comfort O will display when the
heater is outside of a timed heating period. When Manual, Eco or Frost modes are being used
the heater will always maintain the temperature shown on the home screen.
Set the Time
To set the date and time on the heater, press Menu, then press Enter with Time / Date highlighted.
Press or until the correct value is shown, then press Enter to conrm and move on to the
next value. Repeat until all details are correct, and Set displays, then press Back.
The time is automatically adjusted in spring and autumn between Greenwich Mean Time (GMT)
and British Summer Time (BST).
Set the Temperature
The temperature shown on the display is the room temperature set point (target room
temperature). This is the temperature that the heater will maintain during the heating periods.
If the room temperature is above this temperature then the heater will not operate. The heater
leaves the factory with this temperature set at 21°C which represents a typical, comfortable
room temperature. If you require a dierent room temperature then press either or until the
display shows the temperature you require.
Timer Modes
Your Dimplex GFPE Panel comes
pre-programmed with four timer
modes. These modes dene
the periods when the heater will
operate in Comfort On mode.
The four modes are shown in Fig.5
Timer ModeDescription
User timerCustomise times in four periods
Out All Day6 hours heating per day in two periods
Home All Day13 hours heating per day in one period
Holiday
Set the temperature and number of
days for which you are on holiday
Fig. 5
Child Lock
If you need to lock the controls so that the settings
cannot be changed then activate the Child Lock.
To lock the controls press and hold both the Back
button and Enter for three seconds. Child Lock will
appear at the bottom of the screen. To unlock the
control repeat the action by pressing both the Back
button and Enter for three seconds.
Out All Day
Comfort On
Child Lock
8
Loading...
+ 18 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.