Dimplex GDS331304CH User Manual

Owner’s Manual
Model WRCPF-KIT
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this device. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit www.dimplex.com
7209110100R03
2 www.dimplex.com
Table of Contents
Welcome & Congratulations . . . . . . . . . . . . 3
Product Overview .....................4
Receiver Installation (BF units only) ......5
Wall Control Installation ...............7
Initialization ........................14
Operation ..........................15
Warranty ..........................20
!
NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures
and techniques which, if not carefully followed, will result in damage to the equipment.
WARNING: Procedures
and techniques which, if not carefully followed, will expose
the user to the risk of re,
serious injury, or death.
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase a Wall Switch Remote Control Kit from Dimplex, the world leader in electric
replaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial number ready. (See above)
4 www.dimplex.com
Product Overview
The Wall Switch Remote Control Kit is designed to work with the following Dimplex electric
replaces:
BF33STP
BF33DXP
BF39STP
BF39DXP
BF45DXP
BFSL33
BLF50
DF3033ST
DFG3033BLK
For the BF units, mentioned above, follow the Remote Receiver control installation instructions starting on page 5.
For replace models BFSL33,
BLF50, DF3033ST and DFG3033, the pre-installed remote receiver in these models is compatible with the Wall
Switch Remote Control. The
Remote Receiver and bracket contained in this kit will not be required, proceed directly to the
Wall Control Installation on page
7.
!
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause interference and; (2) this device must accept any interference, including interference that may cause undesired operation of the device.
5
Receiver Installation (BF units only)
Open steel curtain (remove 1.
glass doors if applicable).
Remove two (2) screws on log 2.
grate and remove log grate (Figure 1).
Figure 1
Screws
Manual Controls
Pull front edge of plastic 3.
ember bed grate up and forward until rear tab releases from the ledge located at the bottom of the partially
reective glass (Figure 2).
Figure 2
Back ledge
Rear tab
Side section
Locate and remove the two (2) 4.
screws on the manual control bracket (Figure 3). Remove the bracket.
Locate and depress the 5.
mounting tabs on the plug connector and remove the manual control bracket from
replace (Figure 3).
Figure 3
Screw locations
Log ember bed
Front edge
Mounting
tabs
!
NOTE: Log set ts tightly into
rebox, some force may be
Manual controls
necessary to remove.
Plug connector
6 www.dimplex.com
Receiver Installation (BF units only)
Locate the plastic 9-pin plug 6.
in the bottom corner of the
replace where the manual
controls were plugged in to.
Insert the plug connector from 7.
the remote control bracket (Figure 4) into plastic plug
inside the replace.
Figure 4
Remote Control
Run black antenna wire under 8.
remote bracket and ensure all wiring is placed such that it does not interfere with re­assembly.
ledge (Figure 2) and the logs are resting against the partially
reective glass.
Replace log grate using two 11. (2) screws previously removed in step 2.
Antenna
Plug
Connector
Install the two (2) screws 9.
removed in step 4 into the remote control bracket and
attach it to the replace.
Replace the log set by 10. inserting front edge and pushing the back down until rear tab snaps under back
7
Wall Control Installation
!
NOTE: All electrical wiring
must comply with all national and local electrical codes and regulations. Always
use a qualied and licensed
electrician should you have any questions or concerns for all wiring work.
!
NOTE: The Wall Switch
Remote Control is made
to t standard Decora
style faceplates. Due to material inconsistencies of individual faceplates, it may be necessary to remove the faceplate for operations such as changing batteries.
Site Selection for Installation
Although this Wall Switch Remote Control can operate on battery power or by hard wire installation, a convenient and accessible location should be chosen. The range of the Wall Switch Remote Control is approximately 50 feet (15 m).
Installation requires the use of a standard device box and should the hard wire installation method be chosen, a location near an
available 24V~ power source should be considered.
WARNING: Electrocution or
other bodily harm and property damage can occur if a live wire is touched or damaged during installation. Always consult electrical schematics for the installation location of
all wiring or consult a qualied
and licensed electrician before you begin.
Installation
Required Tools and Hardware:
Flat head screwdriver
Wire cutters / strippers
Two (2) wire nuts for 22 AWG wire
Standard wall device box with minimum depth of 2.5 inches (6.35 cm)
24V~ Power supply (for hard wired power installation if applicable)
Battery Powered Installation
1. Remove the Wall Switch
Remote Control and installation hardware from its package.
8 www.dimplex.com
Wall Control Installation
2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push­lock latches and allow the Controller to be removed from the Outer Housing (Figure 5).
Figure 5
Outer
Housing
Controller
Figure 6
3. Open the Battery Compartment as shown in Figure 6 and remove the Insulating Strip as shown in Figure 7.
Figure 7
Insulating
Strip
4. Replace the battery compartment cover.
5. Reinsert the Controller back into the Outer Housing by realigning the tracks on the top and bottom of the unit with the guides inside the Outer Housing. Push the Controller in until you hear the push­lock latches click (Figure 8).
6. Slide the Controller and Outer Housing assembly into
Battery
Compartment
a standard device box and
fasten with the two (2) at
9
Wall Control Installation
Figure 8
to complete the installation and to blend the installation in
Controller
Tracks
with your choice of decor.
Hard Wired Power Supplied Installation
Before starting this installation, it is helpful to initialize the Wall Switch Remote Control with your
rebox (see Initialization section).
You should have the following items ready and prepared:
Guides
Outer
Housing
Installed standard wall device
Figure 9
box with a minimum depth of
2.5 inch (6.35 cm).
Controller
A 24V~ power source leading to the device box. Possible sources could be a 24V~ doorbell circuit or a Class 2 24V~ transformer.
The 24V~ wire leads coming
Wall Box
into the device box should have between 4 and 6 inches (10-15
Outer Housing
Flat head screws (supplied)
cm) of slack left inside the box to allow for ease of installation and/or servicing.
You may also leave the
head screws (supplied) as shown in Figure 9.
supplied AAA batteries in the Controller. There is an internal electronic bypass that will draw
7. Attach your choice of Decora style faceplate (not supplied)
on the hard wired power source before the batteries.
10 www.dimplex.com
Wall Control Installation
1. Unpack the Wall Switch Remote Control and all hardware from its package.
2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push­lock latches and allow the Controller to be removed from the Outer Housing (Figure 5).
3. Push the wire lead storage compartment cover on the back of the Control towards the right (as shown), and remove (Figure 10).
Figure 10
of the two holes located on the wire lead storage compartment cover (make sure orientation is as shown as in Figure 11).
Figure 11
5. Replace the wire lead storage compartment cover on the Controller with wire leads fed through and exposed.
6. Feed the two wire leads from the Controller through the two holes in the back of the Outer Housing as shown in Figure 12.
7. Gently pull the wire leads through while pushing the Controller into the Outer Housing until you hear the push
4. Uncoil the two wire leads and feed each of them through one
lock latches click, locking the Controller in place (Figure 13).
11
Wall Control Installation
Figure 12
Controller
Figure 13
Outer
Housing
Locking Screw Option (Figure 14)
To prevent tampering, damage, and theft, it is suggested to install the locking screws. Once installed, the locking screws will prevent the Controller from being released from the Outer Housing
without being removed rst from
the device box in the wall.
!
NOTE: A Philips head
screwdriver will be required for this step.
Figure 14
Locking
screws
Outer Housing
8. Using the wiring diagram in Figure 15 as a guide, make the appropriate wire connections.
12 www.dimplex.com
Wall Control Installation
Figure 15
Figure 16
Ensure each of the two
Controller lead wires are
connected to separate Low
Voltage 24V~ only wires.
Controller wire leads
Low Voltage
24V~ power source ONLY
Flat Head Screws (supplied)
13
Wall Control Installation
!
NOTE: Wire leads are not
polarized due to the nature of this device.
9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing into the device box (Figure 16). Fasten with two
supplied at head screws.
10. Attach your choice of Decora style faceplate (not supplied) to complete the installation and to blend the installation in with your choice of decor.
11. Initialize the sender with the receiver installed in your
replace.
14 www.dimplex.com
Initialization
After installation, locate the section which applies to your
specic model of replace and
follow the steps for remote control initialization and if required, re-initialization. Refer to your
replace's owner's manual to
locate manual or other controls as needed.
BF Models Using the Included Receiver Module
1. Ensure that power is supplied through main service panel.
2. Inside the replace, locate the
toggle switch on the manual controls and set to “Remote” (Figure 17-C).
Figure 17
D
E F
A
B C
3. Press and hold the On button on the manual controls
(Figure 17-A) for ve (5)
seconds. The Level 1 Indicator Light (Figure 17-D)
will then ash for 10 seconds.
4. Press any button on the Wall Switch Remote Control within that 10 seconds.
BLF50 Models
1. Ensure that power is supplied through main service panel.
2. Inside the replace, turn Main
On/Off Switch to Off (Figure 18-A) and wait 10 seconds.
3. Move the Three Position
Switch (Figure 18-B) to the
REMOTE ” position.
Figure 18
C
BLF50 Manual controls
B A
4. Turn Main On/Off Switch to On.
5. Press and hold the Manual Control Button marked “
I ” (Figure 18-C) for ve (5) seconds. After ve (5)
seconds, there is a 10 second window to press any button on the remote control.
6. Press any button on the Wall Switch Remote Control within that 10 seconds.
15
Initialization
DF3033ST and DFG3033 Models
1. Ensure that power is supplied through main service panel.
2. Ensure the Main On/Off Switch located in the switch box on
the replace in the upper right
hand corner is in the
On
position (Figure 19A).
Figure 19
ABC
DF3033ST / DFG3033
Manual controls
Operation
Manual Controls
3. Set the 3 Position Manual Control (Figure 19B) to the Remote position (left position).
4. Press and hold the Initialization Button on the unit (Figure 19C).
5. While holding the Initialization Button, press any button on the Wall Switch Remote Control.
6. Release the Initialization Button and button pressed on the Control, sender is
initialized with the replace.
The following instructions will cover the operation of the manual controls installed with the receiver
The replace can be controlled
with switches located on the
receiver as shown in Figure 20. board contained with this kit (BF unit installations). For the
!
operation of manual controls for other installations (BLF50, DF3033ST and DFG3033),
please consult your Owner's Manual for those specic models.
NOTE: Firebox must have
the Main On/Off and mode selector switch in the full on position for all features to work properly.
16 www.dimplex.com
Operation
Figure 20
A B C
D
A. On Button
Pressing this button toggles sequentially through the three
levels of the replace. Pressing once activates Level 1 - ame
effect only, twice activates Level 2
- ame effect and Purire™, three times activates Level 3 - ame effect, Purire™ and heat.
B. Off Button
Pressing this button at any time will shut the unit off.
C. Manual Selection Switch
OFF (center): Makes the unit inoperable.
MANUAL (top): All functions
of the replace are controlled
by the On and Off buttons as described above (A, B).
REMOTE (bottom): All
functions of the replace are
controlled by the Wall Switch Remote Control.
D. LED Indicators
Depicts which of the three (3)
levels the replace is currently
operating at: Level 1 - ame effect
only; Level 2 - ame effect and
Purire™; Level 3 - Flame effect,
Purire™ and heat.
!
NOTE: The third LED (Level 3)
on receiver board will always be illuminated when the Manual Selection Switch is set to REMOTE. The only time that the LED is turned off is when the thermostat is set to “Heat Off”.
Switches the operation of the
replace between the different modes of the replace:
17
Operation
Wall Switch Remote Control
6 7
5
8
10
12
4
Display Operation
1. Room Temperature
2. Set Temperature
3. Flame Effect
4. Purire™
5. Heat Off Indicator
6. Function Lock Indicator
7. RF Code Function Indicator
1
2
9
11
13
3
14
8. Set Temperature Down
9. Set Temperature Up
10. Flame Off
11. Flame On
12. Purire™Off
13. Purire™On
14. Low Battery Indicator
18 www.dimplex.com
Operation
1. Room Temperature
Displays current ambient temperature in the room.
2. Set Temperature
Displays and controls the heater to the temperature at which the thermostat is currently set to. Press 8 to lower the thermostat and press 9 to raise the thermostat. Pressing both 8 and 9 together will toggle between Celsius and Fahrenheit.
3. Flame Effect Icon
The ame icon will icker if and
when the Flame Effect is turned on. Press 11 to turn the Flame Effect on, and press 10 to turn the Flame Effect off.
4. Purire™Icon
The display arrows for the Purire™will cycle when turned on. Press 13 to turn the Purire™ function on, and press 12 to turn
Purire™ off.
those units with the Purire™
installed.
5. Heat Off Indicator
This function manually overrides
the thermostat control and
prevents the replace’s heater
from coming on.
To do this, press 8 to decrease
Set Temperature to any
o
temperature below 0
C or 32o F. To reactivate heat from “HEAT OFF” setting, press 9 to increase the thermostat Set Temperature. The Set Temperature will be displayed starting at 21o C (70o F), replacing the “HEAT OFF” icon.
6. Function Lock Indicator
Enabling this function will lock out the Wall Switch Remote Control so as to prevent the current settings from being changed. To Enable, press 8, 9, and 10 sequentially. To disengage, press 8, 9 and 10 sequentially again. The Indicator icon will be displayed when enabled.
!
NOTE: The Purire™ function
on this device will control only
19
Operation
7. RF Code Function and Change Procedure
In the event that the Wall Switch Remote Control does not work properly with the receiver due to interference from additional wireless signals, this function will allow the RF code to be changed.
To enable this function, press 9 and 12 together. “COD” will
appear on the display for ve (5)
seconds and the RF code will change automatically. Repeat
procedure as needed to nd a code that operates the replace
without interference.
Re-initialization of the Wall Switch Remote Control will need to take place with receiver after a new code has been activated. See initialization instructions on page 14.
14. Low Battery Indicator
When displayed, the indicator will signal that the batteries are low and should be replaced. To further extend battery life, the LED backlighting is turned off when the Low Battery Indicator is displayed.
Other Functions
6 Hour Sleep Timer
This feature ensures all functions are turned off six hours after any last button has been pressed.
To turn this feature on and off press 9, 11, 10, and 8 sequentially.
When activated, “6 Hr” will display for 5 seconds while the rest of the LCD remains blank. For the duration of the 6 hour delay, all functions remain working until the 6 hour time delay runs out. The Set Temperature and Room Temperature icons will alternately display their settings and the “6 Hr” icon display. After 6 hours have passed and all functions are turned off, “6 Hr” will ash until any button is pressed.
!
NOTE: If any button is
pressed while this function is enabled, the 6 hour timer will start over for another 6 hour period.
If / when deactivated, “- Hr” will
display for ve (5) seconds.
Warranty
This Dimplex Wall Switch Remote Control is warranted against defects in workmanship and materials for two years from date of sale. This warranty does not apply to damage from accident, misuse, or alteration, nor where the connected voltage is more that 5 % above the nameplate voltage, nor to equipment improperly installed or wired or maintained in violation of the instruction sheet. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser of the product only and is not transferable. No other written or oral warranty applies. No employee, agent, dealer or other person is authorized to give any warranties on behalf of Dimplex. The
customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs. Within the limitations of this warranty, inoperative units shall be returned to the nearest Dimplex authorized service center, and we shall repair or replace, at our option, at no charge to you with return freight paid be Dimplex. It is agreed that such repair or replacement is the exclusive remedy available from Dimplex and that
DIMPLEX IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGE. Some States do not allow the exclusion or limitation of consequential damages, so the above exclusion or limitation may not apply to you. This
warranty gives you specic legal rights
and you may also have other rights which vary from state to state.
Dimplex North America Limited
1367 Industrial Road Cambridge ON Canada N1R 7G8
© 2012 Dimplex North America Limited
20 www.dimplex.com
Loading...