08/50258/0 (UK) Issue 0
The product complies with the European Safety Standards EN60335-2-30 and the European S tandard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Branscombe
Barletta
Dillon
950
250
1070
Dillon
950
250
1070
Barletta
950
250
1070
Branscombe
1
2
M
A
X
T
M
IN
1
2
3
1
2
Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical
shock and injury to persons, including the following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower
or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they
do not play with the appliance.
Do not use this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
WARNING: In order to avoid overheating, do not cover the
heater. Do not place material or garments on the heater, or
obstruct the air circulation around the heater.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier. Loose
coals/pebbles are packed separately within the carton. When the heater
is assembled the coals/pebbles are placed on top of the fuel bed
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires little electricity.
These models are designed to be free standing and are normally
positioned against a wall.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Wall fixing - see Fig. 1
Attach the wall brackets to the appliance with the screws supplied see Fig. 1.
The appliance should then be securely fixed to the wall using the wall
plug and screw supplied for block walls.
Note – for studded walls special fasteners are required, see diagram
for recommended position of fixing screws.
Controls - see Fig. 2
Three switches provide a choice of heat settings. A switch is in the ON
position when the side with the markings on (i.e. I, I, or II) is pushed in.
Switch 1 (I) Controls the electricity supply to the heater and flame
effect.
Note: This switch must be in the ON (I) position for
heater to operate with or without heat.
Switch 2 (I) Provides 1kW heat output.
Switch 3 (II) Provides 2kW output with switch 2.
Thermostat (T)
In order to maintain a certain room temperature, set the controller to
‘max.’. Operate the appliance at full power until the required room
temperature is reached. Set back the thermostatic controller until the
appliance switches off with an audible “click”. This temperature will be
kept almost constant by the thermostatic control switching on and off
automatically.Please note that the appliance can only be switched on
when the thermostat setting is higher then the room temperature.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent damage
due to overheating. This can happen if the heat outlet was restricted in
any way. The heater will switch on once the obstruction has been
removed and the heater has cooled. If the cut-out continues to operate
intermittently, the heater should be switched off and a service agent
contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) bulbs in place of
conventional bulbs . These generate the same light levels as conventional
bulbs, but use a fraction of the energy consumed. These LED bulbs are
maintenance–free and will not require replacing during the life of the
product.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully with
a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment
of a vacuum cleaner should occasionally be used to clean the outlet
grille of the fan heater.
To clean the fuel effect, remove the coals/pebbles and wash in warm
water. The plastic tray should be wiped clean with a damp cloth. When
dry replace the coals/pebbles and arrange for best effect.
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULL Y AND RET AINED FOR FUTURE REFERENCE
Barletta, Branscombe & Dillon Suites
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
UK customer help line 8.00am–5.00pm Mon-Fri and 8:30am-1.00pm Sat (October–March)
Customer Services: Tel. 0845 600 5111
Fax. 01489 773053
e-mail customer.services@glendimplex.com
Republic of Ireland Tel. 01 8424833
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0845 600 5111. It would assist us if you can
quote the model number, series, date of purchase, and nature of the
fault at the time of your call. The customer services help desk will also
be able to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this
may result in loss or damage and delay in providing you with a
satisfactory service.
Please retain your receipt as proof of purchase.
Loading...