Digitus DN-70590, DN-70690 User Manual

300 MBIT DUAL BAND

WIRELESS ACCESS

POINT | ROUTER

User Manual

DN-70590

publication may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language or computer language, in any form or

by any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission of this company

This company makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties, merchantability or fitness for any particular purpose. Any software

described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase, the buyer (and not this company, its

distributor, or its dealer) assumes the entire cost of all necessary servicing,

repair, and any incidental or consequential damages resulting from any defect

in the software. Further, this company reserves the right to revise this

publication and to make changes from time to time in the contents thereof

without obligation to notify any person of such revision or changes.

Federal Communication

Commission

Interference Statement

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This equipment must be installed and operated in accordance with provided

instructions and a minimum 20 cm spacing must be provided between

computer mounted antenna and person’s body (excluding extremities of hands,

wrist and feet) during wireless modes of operation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall not

be less than 20cm (8 inches) during normal operation.

The antenna(s) used for this transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

The equipment version marketed in US is restricted to usage of the channels

1-11 only.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC

OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on

radio equipment and telecommunication terminal Equipment and the mutual

recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station

Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who

install and use it. However, special attention must be paid to the dangers of

electric shock and static electricity when working with electrical equipment. All

guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria,

Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,

Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United

Kingdom.

The ETSI version of this device is also authorized for use in EFTA member

states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not intended for use

None.

CONTENTS

CHAPTER I: PRODUCT INFORMATION

1-1 Introduction and safety information

1-2 Safety Information

1-3 System Requirements

1-4 Package Contents

1-5 Know your new wireless broadband router

CHAPTER II: SYSTEM AND NETWORK SETUP

2-1 Build network connection

2-2 Connecting to wireless broadband router by web browser 2-2-1 Windows 95/98/Me IP address setup 2-2-2 Windows 2000 IP address setup 2-2-3 Windows XP IP address setup 2-2-4 Windows Vista IP address setup 2-2-5 Router IP address lookup

2-3 Using ‘Quick Setup’ 2-3-1 Setup procedure for ‘Cable Modem’ 2-3-2 Setup procedure for ‘Fixed-IP xDSL’ 2-3-3 Setup procedure for ‘PPPoE xDSL’ 2-3-4 Setup procedure for ‘PPTP xDSL’ 2-3-5 Setup procedure for ‘L2TP xDSL’ 2-3-6 Setup procedure for ‘Telstra Big Pond’

2-4 Basic Setup 2-4-1 Time zone and time auto-synchronization 2-4-2 Change management password 2-4-3 Remote Management

2-5 Setup Internet Connection (WAN Setup) 2-5-1 Setup procedure for ‘Dynamic IP’ 2-5-2 Setup procedure for ‘Static IP’ 2-5-3 Setup procedure for ‘PPPoE’ 2-5-4 Setup procedure for ‘PPTP’ 2-5-5 Setup procedure for ‘L2TP’ 2-5-6 Setup procedure for ‘Telstra Big Pond’ 2-5-7 Setup procedure for ‘DNS’ 2-5-8 Setup procedure for ‘DDNS’ 2-5-9 Setup procedure for ‘WISP’

2-6 Wired LAN Configurations 2-6-1 LAN IP section 2-6-2 DHCP Server 2-6-3 Static DHCP Leases Table

2-7 Wireless LAN Configurations 2-7-1 Basic Wireless Settings 2-7-1-1 Setup procedure for ‘AP' 2-7-1-2 Setup procedure for ‘Station-Infrastructure' 2-7-1-3 Setup procedure for ‘AP Bridge - Point to Point’ 2-7-1-4

Setup procedure for ‘AP Bridge - Point to Multi Point’

2-7-1-5 Setup procedure for ‘AP Bridge - WDS’ 2-7-1-6 Setup procedure for ‘Universal Repeater' 2-7-2 Advanced Wireless Settings 2-7-3 Wireless Security 2-7-3-1 Disable wireless security 2-7-3-2 WEP - Wired Equivalent Privacy 2-7-3-3 Wi-Fi Protected Access (WPA) 2-7-3-4 WPA RADIUS 2-7-4 Wireless Access Control 2-7-5 Wi-Fi Protected Setup (WPS) 2-7-6 Security Tips for Wireless Network

CHAPTER III: ADVANCED FUNCTIONS

3-1 Quality of Service (QoS) 3-1-1 Basic QoS Settings 3-1-2 Add a new QoS rule

3-2 Network Address Translation (NAT) 3-2-1 Basic NAT Settings (Enable or disable NAT function) 3-2-2 Port Forwarding 3-2-3 Virtual Server 3-2-4 Port Mapping for Special Applications 3-2-5 UPnP Setting 3-2-6 ALG Settings

3-3 Firewall 3-3-1 Access Control 3-3-1-1 Add PC 3-3-2 URL Blocking 3-3-3 DoS Attack Prevention 3-3-3-1 DoS - Advanced Settings 3-3-4 Demilitarized Zone (DMZ)

3-4 System Status 3-4-1 System information and firmware version 3-4-2 Internet Connection Status 3-4-3 Device Status 3-4-4 System Log 3-4-5 Active DHCP client list 3-4-6 Statistics

3-5 System Tools 3-5-1 Configuration Backup and Restore 3-5-2 Firmware Upgrade 3-5-3 System Reset

CHAPTER IV: APPENDIX

4-1 Hardware Specification

4-2 Troubleshooting

4-3 Glossary

Chapter I: Product Information

1-1 Introduction and safety information

Thank you for purchasing this wireless concurrent dual band gigabit router! This high cost-efficiency router is the best choice for Small office / Home office users, all computers and network devices can share a single xDSL / cable modem internet connection at high speed. Easy install procedures allows any computer users to setup a network environment in very short time - within minutes, even inexperienced. When the number of your computers and network-enabled devices grow, you can also expand the number of network slot by simple attach a hub or switch, to extend the scope of your network!

With built-in both 2.4GHz and 5GHz radios, this router supports both of the IEEE 802.11b/g/n and 802.11a/n wireless network capabilities simultaneously, all computers and wireless-enabled network devices (including PDA, cellular phone, game console, and more!) can connect to this wireless router without additional cabling. New N wireless capability also gives you the highest speed of wireless experience ever! With a compatible wireless card installed in your PC, you can transfer file for up to 300Mbps (transfer data rate)! The radio coverage is also doubled, so don’t worry if your office or house is really big!

Other features of this router including:

• Supports 2.4GHz and 5GHz wireless devices simultaneously.

• High Internet Access throughput.

• Allow multiple users to share a single Internet line.

• Share a single Cable or xDSL internet connection.

• Access private LAN servers from the internet.

• Four wired LAN ports (10/100/1000M) and one WAN port

(10/100/1000M).

• Provides IEEE 802.11a/b/g/n wireless LAN capability.

• Support DHCP (Server/Client) for easy IP-address setup.

• Support multiple wireless modes like: AP, Station-Infrastructure,

Wireless Bridge and Universal Repeater.

• Advanced network and security features like: Special Applications, QoS,

DMZ, Virtual Servers, Access Control, Firewall.

• Allow you to monitor the router’s status like: DHCP Client Log, System

Log, Security Log and Device/Connection Status.

• Easy to use Web-based GUI for network configuration and

management purposes.

• Remote management function allows configuration and upgrades from

a remote computer (over the Internet).

•

Auto MDI / MDI-X function for all wired Ethernet ports.

1-2 Safety Information

In order to keep the safety of users and your properties, please follow the

following safety instructions:

1. This router is designed for indoor use only; DO NOT place this router

outdoor.

2. DO NOT put this router at or near hot or humid places, like kitchen or

bathroom. Also, do not left this router in the car in summer.

3. DO NOT pull any connected cable with force; disconnect it from the router

first.

4. If you want to place this router at high places or hang on the wall, please

make sure the router is firmly secured. Falling from high places would damage

the router and its accessories, and warranty will be void.

5. Accessories of this router, like antenna and power supply, are danger to

small children under 3 years old. They may put the small parts in their nose or

month and it could cause serious damage to them. KEEP THIS ROUTER OUT

THE REACH OF CHILDREN!

6. The router will become hot when being used for long time (This is normal

and is not a malfunction). DO NOT put this router on paper, cloth, or other

flammable materials.

7. There’s no user-serviceable part inside the router. If you found that the

router is not working properly, please contact your dealer of purchase and ask

for help. DO NOT disassemble the router, warranty will be void.

8. If the router falls into water when it’s powered, DO NOT use your hand to

pick it up. Switch the electrical power off before you do anything, or contact an

experienced technician for help.

9. If you smell something strange, or even see some smoke coming out from

the router or power supply, remove the power supply or switch the electrical power off immediately, and call dealer of purchase for help.

1-3 System Requirements

 Internet connection, provided by xDSL or cable modem with a RJ-45

Ethernet port.

 Computer or network devices with wired or wireless network interface

card.

 Web browser (Microsoft Internet Explorer 4.0 or above, Netscape

Navigator 4.7 or above, Opera web browser, or Safari web browser).

 An available AC power socket (100 – 240V, 50/60Hz)

1-4 Package Contents

Before you starting to use this router, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items:

Gigabit router (main body, 1 pcs) ....................................... 1

Quick installation guide (1 pcs) ........................................... 2

User manual CDROM (1 pcs) ............................................. 3

A/C power adapter (1 pcs) .................................................. 4

1-5 Know your new wireless broadband router

Front Panel

LED Name Light

Status

Description

PWR

On Router is switched on and correctly

powered.

2.4G

On 2.4GHz Wireless WPS function is

enabled.

Off 2.4GHz Wireless network is switched off.

Flashing 2.4GHz Wireless LAN activity

(transferring or receiving data).

On 5GHz Wireless WPS function is enabled.

Off 5GHz Wireless network is switched off.

Flashing 5GHz Wireless LAN activity (transferring

or receiving data).

LAN 1-4 LNK/ACT

On LAN port is connected.

Off LAN port is not connected.

Flashing LAN activity (transferring or receiving

data).

WAN LNK/ACT

On WAN port is connected.

Off WAN port is not connected.

Flashing WAN activity (transferring or receiving

data).

LAN 1-4 1000M

On LAN port is linked in 1000Mbps speed.

Off LAN port is linked in 10/100Mbps speed.

WAN 1000M

On WAN port is linked in 1000Mbps speed.

Off WAN port is linked in 10/100Mbps speed.

Back Panel

Item Name Description

Antenna A/B It is dual band 3dBi dipole antenna.

Radio

ON/OFF

Switch the button to activate or deactivate the wireless

functions.

Reset / WPS Reset the router to factory default settings (clear all settings)

or start WPS function. Press this button and hold for 10

seconds to restore all settings to factory defaults; press this

button for less than 5 seconds once to start 2.4GHz wireless

WPS function, and press this button for less than 5 seconds

twice to start 5GHz wireless WPS function.

WAN Wide Area Network (WAN / Internet) port.

1 – 4 Local Area Network (LAN) ports 1 to 4.

Power Power connector, connects to A/C power adapter.

Antenna A Antenna B

Chapter II: System and Network Setup

2-1 Build network connection

Please follow the following instruction to build the network connection between your new WIRELESS router and your computers, network devices:

1. Connect your xDSL / cable modem to the WAN port of router by Ethernet cable.

2. Connect all your computers, network devices (network-enabled consumer devices other than computers, like game console, or switch / hub) to the LAN port of the router.

3. Connect the A/C power adapter to the wall socket, and then connect it to the ‘Power’ socket of the router.

4. Please check all LEDs on the front panel. ‘PWR’ LED should be steadily on, WAN and LAN LEDs should be on if the computer / network device connected to the respective port of the router is powered on and correctly connected. If PWD LED is not on, or any LED you expected is not on, please recheck the cabling, or jump to ‘4-2 Troubleshooting’ for possible reasons and solution.

2-2 Connecting to wireless broadband router by web browser

After the network connection is built, the next step you should do is setup the router with proper network parameters, so it can work properly in your network environment.

Before you can connect to the router and start configuration procedures, your computer must be able to get an IP address automatically (use dynamic IP address). If it’s set to use static IP address, or you’re unsure, please follow the following instructions to configure your computer to use dynamic IP address:

If the operating system of your computer is….

Windows 95/98/Me - please go to section 2-2-1

Windows 2000 - please go to section 2-2-2 Windows XP - please go to section 2-2-3 Windows Vista - please go to section 2-2-4

2-2-1 Windows 95/98/Me IP address setup:

1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network icon, and Network window will appear. Select ‘TCP/IP’, then click ‘Properties’.

2. Select ‘Obtain an IP address from a DHCP server’ and then click

‘OK’.

2-2-2Windows 2000 IP address setup:

1. Click ‘Start’ button (it should be located at lower-left corner of

your computer), then click control panel. Double-click Network and

Dial-up Connections icon; click Local Area Connection, and Local Area Connection Properties window will appear. Select

‘Internet Protocol (TCP/IP)’ and then click ‘Properties’

2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS

server address automatically’, then click ‘OK’.

2-2-3Windows XP IP address setup:

1. Click ‘Start’ button (it should be located at lower-left corner of

your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click ‘Properties’

2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS

server address automatically’, then click ‘OK’.

2-2-4Windows Vista IP address setup:

1. Click ‘Start’ button (it should be located at lower-left corner of

your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select ‘Properties’. Local Area Connection Properties window will appear, select ‘Internet Protocol Version 4 (TCP / IPv4), and then click ‘Properties’

2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS

server address automatically’, then click ‘OK’.

2-2-5 Router IP address lookup

After the IP address setup is complete, please click ‘start’ -> ‘run’ at the bottom-lower corner of your desktop:

Input ‘cmd’, then click ‘OK’

Input ‘ipconfig’, then press ‘Enter’ key. Please check the IP address followed by ‘Default Gateway’ (In this example, the IP address of router is 192.168.2.1, please note that this value may be different.)

NOTE: If the IP address of Gateway is not displayed, or the address followed

by ‘IP Address’ begins with ‘169’, please recheck network connection

between your computer and router, and / or go to the beginning of this

chapter, to recheck every step of network setup procedure.

3. Connect the router’s management interface by web browser

After your computer obtained an IP address from router, please start your web browser, and input the IP address of router in address bar. The following message should be shown:

Please input user name and password in the field respectively, default user name is ‘admin’, and default password is ‘1234’, then press ‘OK’ button, and you can see the web management interface of this router:

NOTE: If you can’t see the web management interface, and you’re

being prompted to input user name and password again, it means you

didn’t input username and password correctly. Please retype user

name and password again. If you’re certain about the user name and

password you type are correct, please go to ‘4-2 Troubleshooting’ to

perform a factory reset, to set the password back to default value.

TIP: This page shows the four major setting categories: Quick Setup,

General Setup, Status, and Tools. You can find the shortcut which

leads to these setting categories at the upper-right corner of every

page, and you can jump to another category directly by clicking the

link, and don’t have to go back to the first page.

+ 140 hidden pages

Digitus DN-70590, DN-70690 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual