Digitus DN-13008 User manual

Digitus

DN-13007 / DN-13008 / DN-13018

USB 2.0 Hi-Speed MFP Server

Quick Installation Guide

. Introduction

①

This document describes the steps for installing and configuring

Digitus DN-13007/DN-13008/DN-13018 USB 2.0 MFP server as a

Print/File/Scan server in the Windows environment. Digitus

DN-13007/DN-13008 uses LAN (standard Ethernet) to access network,

while Digitus DN-13018 uses LAN or wireless module (802.11b/g) to

access network. The following table shows the differences among

DN-13007, DN-13008, and DN-13018.

Model LAN Wireless USB Port(s)

DN-13008 Yes No 1

DN-13007 Yes No 2

DN-13018 Yes Yes 2

Except for the wireless configuration, most configuration and

operations are the same for DN-13007/DN-13008 and DN-13018.

Similarly, almost all of the configuration and operations are the same

for DN-13007 and DN-13008 except that only one USB device can be

connected to DN-13008 while at most two USB devices can be

connected to DN-13007. Please refer to the User’s Manual in the

bundled CD-ROM for more details.

- This Setup Guide is only for Windows users.

- If you use the MFP server in Unix/Linux, please refer to the User’s

Manual in the bundled CD-ROM for more details.

. Package Contents

②

If any item is missing, please contact the shop where you bought this

product.

- One Digitus DN-13007 or DN-13008 or DN-13018 USB 2.0 MFP

Server (x1)

- One MFP Control Center Software CD (x1)

- One DC IN 12V/1A Power Adaptor (x1)

. OS Requirements

③

I. Windows 2000/XP/2003/Vista II. Unix, Linux , Apple OS X 10.3x, and RFC-1179 LPD System

. Physical Description

④

1. Power Adaptor Connector: DC IN 12V/1A adaptor

2. Init Button: restore the configurable parameters to the default

values

3. Wireless Station (only for DN-13018): IEEE 802.11 b/g wireless

station with antenna inside

4. Ethernet Connector: a twisted pair category 5 cable

5. USB Host Ports: USB 1.1/2.0 low, full, and Hi-Speed compliant

6. Indicators  Power Indicator is lit while power is applied. If it is not lit, or if

it blinks, there is a problem with the MFP server or Power

Adapter.

 Link Status (only for DN-13007/DN-13008) is lit while network

is applied. If it is not lit, it indicates that this server does not

connect to the network.

 Status Indicator (only for DN-13007/DN-13008) blinks to

indicate network activity.

 LAN Indicator (only for DN-13018) blinks to indicate wired

network activity. If it is lit, it indicates the wired network is

applied. If it is not lit, it indicates that the server does not

connect to the wired network.

 WLAN Indicator (only for DN-13018) blinks to indicate wireless

network activity. If it is lit, it indicates the wireless network is

applied. If it is not lit, it indicates that the server does not

connect to the wireless network.

 USB1 Indicator is lit while a USB device connects to USB1 Port

of the MFP server. If it is not lit, or if it blinks, there is a

problem with the USB device or the MFP server.

 USB2 Indicator is lit while a USB device connects to USB2 Port

of the MFP server. If it is not lit, or if it blinks, there is a

problem with the USB device or the MFP server.

Note : There is only one USB LED indicator for DN-13008.

. Connect Digitus MFP Server to Your Wired Network

⑤

I. Connect the MFP server to the wired network, such as a LAN switch or a

LAN hub, using a LAN cable.

II. Connect USB printers, hard drives or flash ROM disks, or all-in-one

series printers (AIO/MFP) to the MFP server using USB cables.

III. Plug in the power adaptor (included in this package) to power on the

MFP server.

. Connect Digitus DN-13018 to Your Wireless Network

⑥

Just skip this step if you are using DN-13007 or DN-13008.

I. Follow Step 5. II. Properly set up wireless configuration as Step 8. III. Plug-off the LAN (Ethernet) cable. IV. Plug-off the power adapter and then plug-in the power adapter to

restart server. DN-13018 will connect to your wireless network.

. Install Utility

⑦

I. Insert the included CD-ROM into the personal computer. The

Autorun screen as Fig1 should appear.

Figure 1 Autorun

II. Click Install Product button. III. Click Next, if you see any Next button in installation windows. IV. Click Finish.

. Configure Digitus MFP Server with Utility

⑧

Using MFP Control Center Software (Fig2):

1. Open the Digitus MFP Control Center. It will automatically search the

existing servers and display their statuses.

2. Select the server that you want to configure. Double click the

selected server and enter Administrator (default: admin) and

Password (default: admin).

Figure 2 Control Center

3. Name your Digitus MFP server and select a codepage for file server

function as Fig3. Please enter the server name and the workgroup

name for Windows networking by SMB protocol. The default

server name is the model name (DN-13007 or DN-13008 or

DN-13018) and the workgroup name is “ARBEITSGRUPPE”. If you

want to use the file server function, you have to set the same

codepage as the one that your Windows PC is using.

4. Assign IP address to Digitus MFP server as Fig4. Please choose the

one method to set the IP address of the server. You can

automatically get IP by using DHCP or manually assign an IP to the

server.

+ 9 hidden pages